Livex Lighting 73052-35 Operating instructions

Type
Operating instructions

This manual is also suitable for

Livex Lighting 73052-35 is a ceiling light fixture that can be used to replace an existing fixture. It features a single light bulb and a glass shade. The fixture is easy to install and comes with all the necessary hardware. It is important to shut off the power at the fuse or circuit breaker box before installing the fixture. The fixture is compatible with incandescent, CFL, and LED bulbs. The maximum wattage rating is not specified in the manual, so it is important to check the bulb's packaging before installing it. The fixture is not compatible with dimmers.

Livex Lighting 73052-35 is a ceiling light fixture that can be used to replace an existing fixture. It features a single light bulb and a glass shade. The fixture is easy to install and comes with all the necessary hardware. It is important to shut off the power at the fuse or circuit breaker box before installing the fixture. The fixture is compatible with incandescent, CFL, and LED bulbs. The maximum wattage rating is not specified in the manual, so it is important to check the bulb's packaging before installing it. The fixture is not compatible with dimmers.

ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed.
However, the installation instructions do apply to this product.
73051 73052 73053
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1)
1. Shut off the power at the fuse box or circuit breaker box. Remove the old
fixture from ceiling, including the single bar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area.
Take care not to lose any small parts necessary for installation.
3. Thread the pipe screw part way into the center hole of the single bar and
secure with hex nut.
4. Attach the single bar to the junction box using two box screws as shown. The
side of the single bar marked “GND” must face out . The junction box is
not included.
5. Hold the pan(A) towards the single bar and connect the electrical wires as
follows (See Fig.2). Connect the black wire from the fixture to the black
house (hot) wire; connect the white wire from the fixture to the white house
(neutral) wire. Make sure all wire nuts are secured. You may wrap the
connections with electrical tape. If your Junction box has a ground wire
(green or bare copper) connects fixture’s ground wire to it. Otherwise
attach the bare copper fixture wire to the green ground screw on the single
bar. Tuck the wire connections neatly into the ceiling junction box as you
are holding the fixture assembly toward the ceiling.
6. Raise plate(A) onto the junction box, aligning pipe screw on single bar with
center hole in plate and lock it securely with the ball nut(B).
7. Install the light bulbs(Not included) in accordance with the fixture’s
specifications.
DO NOT EXCEED THE MAXIMUM WATTAGE RATING!
8. Attach the glass shade(C) to the crown(E), raise the assembly to the pan,
aligning the thread hole of pan with the crown's hole, then tighten it with
the screws(D).
Your installation is now complete. Return power to the
j
unction box and test the fixture.
B
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black(Hot)
FIXTURE
WIRES
White or
Ribbed
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green or Bare
Copper(Ground)
Thank you for purchasing a LIVEX product.
Need assistance with parts or assembly? Please call customer service at: 800-761-8056
Or visit us online at: WWW.LIVEXLIGHTING.COM
©COYRIGHT ALL RIGHTS RESERVED.LIVEX LIGHTING,INC. DOC20160173051
FIG.2
FIG.1
  • Page 1 1

Livex Lighting 73052-35 Operating instructions

Type
Operating instructions
This manual is also suitable for

Livex Lighting 73052-35 is a ceiling light fixture that can be used to replace an existing fixture. It features a single light bulb and a glass shade. The fixture is easy to install and comes with all the necessary hardware. It is important to shut off the power at the fuse or circuit breaker box before installing the fixture. The fixture is compatible with incandescent, CFL, and LED bulbs. The maximum wattage rating is not specified in the manual, so it is important to check the bulb's packaging before installing it. The fixture is not compatible with dimmers.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI