Fire Sense 61279 Owner's manual

- 1 -

Outdoor Patio Heater

Model # 61279,61301,61304,61281,61283,61285,61307

61287,61299,61312,61731,61732,61733,61734

Questions, problems, missing parts? Before returning to your

retailer, call our customer service hotline at 1-866-985-7877,

9 a.m. – 6 p.m., EST, Monday – Friday or email at

cservice@welltraveled.net.

ATTACH YOUR RECEIPT HERE

Serial Number ___________ Purchase Date ______

Manufacturer: Changzhou Wellife Furnace Co., Ltd.

- 2 -

Package Contents.......................................................................................................Page 3

Hardware ...................................................................................................................Page 4

Safety Information......................................................................................................Page 4-6

Assembly.....................................................................................................................Page 6-10

Operating Instructions.................................................................................................Page 11-13

Care and Maintenance..................................................................................................Page 14

Troubleshooting...........................................................................................................Page 15

Warranty......................................................................................................................Page 16

TABLE OF CONTENTS

ASSEMBLY

- 3 -

PACKAGE CONTENTS

Wheel Assembly

- 4 -

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install this appliance.

If you have any questions regarding the product, please call customer service at 1-866-985-7877, 9 a.m. –

6 p.m., EST, Monday – Friday.

This manual contains important information about the assembly, operation and maintenance of this patio

heater. General safety information is presented in the first few pages and is also located throughout this manual.

Keep this manual for future reference and to educate new users of this appliance. This manual should be read

in conjunction with the labeling on the appliance. Safety precautions are essential when any mechanical or

propane fueled equipment is involved. These precautions are necessary when using, storing, and servicing this

appliance. Using this appliance with the respect and caution demanded will reduce the possibilities of personal

injury or property damage. The following symbols shown below are used extensively throughout this manual.

Always heed these precautions, as they are essential when using any mechanical or propane fueled equipment.

HARDWARE

ASSEMBLY

SAFETY INFORMATION

- 5 -

SAFETY INFORMATION

- 6 -

PREPARATION

Before beginning assembly of this appliance, make sure all parts are present. Compare all parts with package

contents list and hardware as listed on pages 3 and 4 of this manual. If any part is missing or damaged, do not

attempt to assemble this product. Contact customer service for replacement parts.

ESTIMATED ASSEMBLY TIME: 60 minutes

Tools Required for Assembly (NOT included):

7/16" open-end wrench

Philips screwdriver with medium blade

Adjustable opening wrench

Leak Detection Solution (see instructions on page 11 on how to make solution.)

SAFETY INFORMATION

ASSEMBLY

- 7 -

1. Attach Wheel Assembly to Base. Line up holes in Wheel Assembly with

corresponding holes in Base and insert 2 - Medium Bolts through holes.

Finger tighten bolts. Be sure that Wheel Assembly is parallel to the Base

and fully tighten the bolts.

Note: For best stability, fill the sand box with sand.

Hardware Used: 2 Medium Bolts

2. Attach the Support Brackets to the Base. Attach the 3 - Support Brackets

loosely to the Base with 3 - Medium Bolts inserted through the holes in the

bottom of the Support Brackets and into the Base.

Hardware Used: 3 Medium Bolts

3. Attach the Post to the Support Brackets. Once you have tightened the bolts holding the

Support Brackets to the Base, align the holes in the bottom of the Post

with the holes on the tops of the Support Brackets and insert 6 - Large

Bolts through the hole in the Post and through the hole in the Support

Bracket. Affix 6 - Small Flange Nuts to the bottom of the Large Bolts.

Hand tighten initially then tighten with a wrench when all bolts have

been inserted.

Hardware Used: 6 Large Bolts

6 Small Flange Nuts

ASSEMBLY

- 8 -

4. Place Cylinder Housing onto Post. Slide Cylinder Housing down over

Support Brackets and Post and rest on Base.

5. Attach Reflector Studs to Screen Cover. Insert 3 Reflector Studs through

washers and into holes on screen cover. Tighten studs securely.

Hardware Used:

3 Reflector Studs 3 Large Flat Washers

6. Attach Head Assembly to Post. Unscrew 4 Small Bolts and 4 Lock Washers

pre-assembled in the Head Assembly. Route

Gas Hose down into post and then place

Head Assembly on top of Post.

Note: Control knob should be above the decal

on Post.

Attach Head Assembly to Post by inserting

bolts through lock washers and into holes on

Head Assembly and Post. Once all bolts and

lock washers have been inserted, tighten securely.

Hardware Used:

4 Small Bolts 4 Lock Washers

ASSEMBLY

- 9 -

7. Install Reflector. NOTE: MAKE SURE TO REMOVE PROTECTIVE

PLASTIC COVER ON REFLECTOR PIECES PRIOR TO ASSEMBLY!

Assembly Tip: If necessary for proper alignment of reflector sections,

loosen each screw prior to further assembly and retighten after sections

are aligned.

Slide two Reflector Panels together. Insert one Small Screw.

Screw on Cap Nut loosely.

Repeat with the third Reflector Panel.

Slide Reflector Plate onto assembled Reflector Panels. Insert one

Small Screw and screw on Cap Nut loosely. Repeat with two more

Small Screws and Cap Nuts to complete reflector assembly. Fully

tighten all of the screws and cap nuts.

Hardware Used:

9 Small Screws 9 Cap Nuts

8. Attach Reflector Assembly to heater. While supporting heater,

tilt the Head Assembly and slide 3 Large Flat Washers over the Reflector

Studs. Place the Reflector Assembly onto the Reflector Studs and slide

3 Large Flat Washers over Reflector Studs and onto Reflector Assembly.

Secure with 3 Wing Nuts. Do NOT over tighten.

Once you have tightened the Wing Nuts, return the heater to an upright

position.

Hardware Used:

6 Large Flat Washers 3 Wing Nuts

ASSEMBLY

- 10 -

9. Connect the Hose and Regulator to the LP cylinder. The LP cylinder is

sold separately. Use a standard 20 lb. propane cylinder only. Lift the

Cylinder Housing up and rest it on the top of the assembled Support

Brackets. Screw Regulator onto Gas Hose. Do not cross thread. Hand

tighten securely. Attach Regulator to valve on LP cylinder and hand tighten

securely. Place LP tank onto base of heater and lower Cylinder Housing.

NOTE: Use this heater only with a propane vapor withdrawal supply

system. See Chapter 5 of the standard for storage and handling of liquefied

petroleum gas, ANSI/NFPA 58. Your local library or fire department should

have this book.

A minimum supply pressure of .5 psi is required for the purpose of input adjustment of propane gas. Storage of

an appliance indoors is permissible only if the cylinder is disconnected and removed from the appliance. A

cylinder must be stored outdoors in a well-ventilated area out of the reach of children. A disconnected cylinder

must have dust caps tightly installed and must not be stored in a building, garage, or any other enclosed area.

The minimum permissible gas supply pressure of 11 W.C. is required for purpose of hose adjustment. The

minimum hourly of 17,500 BTU is required input rating for a heater for automatic operation rating less than full

input rating.

The pressure regulator and hose assembly supplied with the appliance must be used.

The installation must conform with local codes, or in the absence of local codes, with national fuel gas code, ANSI

Z223.1/NFPA54, natural gas and propane Installation Code, CSA B149.1, or propane storage and handling code,

B149.2

A dented rusted or damaged propane cylinder may be hazardous and should be checked by your local cylinder

supplier. Never use a propane cylinder with a damaged valve connection.

The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders

of the U.S. Department of Transportation (DOT) or the standard for cylinders, spheres and tubes for

transportation of dangerous goods and commission, CAN/CSA-B339.

The cylinder must have a listed overfilling prevention device.

The cylinder must have a connection device compatible with the connection for the appliance.

The cylinder used must include a collar to protect the cylinder valve.

Never connect an unregulated propane cylinder to the heater.

 Do not store a spare LP-gas cylinder under or near this appliance.

 Never fill the cylinder beyond 80 percent full.

 Place the dust cap on the cylinder valve outlet whenever the cylinder

is not in use. Only install the type of dust cap on the cylinder valve

that is provided with the cylinder valve. Other types of caps or

plugs may result in leakage of propane.

ASSEMBLY

- 11 -

Leak Test

1. Make 2-3 oz. of leak test solution (one part liquid dishwashing detergent and three parts water).

2. Apply several drops of solution where hose attaches to regulator.

3. Apply several drops of solution where regulator connects to cylinder.

4. Make sure all patio heater valves are OFF.

5. Turn cylinder valve ON.

IF BUBBLES APPEAR AT ANY CONNECTION, THERE IS A LEAK.

1. Turn cylinder valve OFF.

2. If leak is detected at hose/regulator connection, tighten connection and perform another leak test. If bubbles continue to

appear, call our customer service hotline at 1-866-985-7877, 9 a.m. – 6 p.m., EST, Monday – Friday.

3. If leak is detected at regulator/cylinder valve connection, disconnect, reconnect, and perform another leak

test. If you continue to see bubbles after several attempts, cylinder valve is defective. Call our customer service

hotline at 1-866-985-7877, 9 a.m. – 6 p.m., EST, Monday – Friday

IF NO BUBBLES APPEAR AT ANY CONNECTION, THE CONNECTIONS ARE SECURE.

Note: Whenever gas connections are loosened or removed, you must perform a complete leak test.

Caution: Do not attempt to operate this appliance until you have read and understand all Safety Information in

this manual and all assembly is complete and leak tests have been performed.

Before Turning Gas Supply ON:

1. Your heater was designed and approved for OUTDOOR use only. Do NOT use it inside a building, garage, or

any other enclosed area.

2. Make sure surrounding areas are free of combustible materials, gasoline, and other flammable vapors or

liquids.

3. Ensure that there is no obstruction to air ventilation. Be sure all gas connections are tight and there are no

leaks.

4. Be sure the cylinder cover is clear of debris. Be sure any component removed during assembly or servicing is

replaced and fastened prior to starting.

Before Lighting:

1. Heater should be thoroughly inspected before each use, and by a qualified service person at least annually. If

re-lighting a hot heater, always wait at least 5 minutes.

2. Inspect the hose assembly for evidence of excessive abrasion, cuts, or wear. Suspected areas should be leak

tested. If the hose leaks, it must be replaced prior to operation. Only use the replacement hose assembly

specified by the manufacturer.

OPERATING INSTRUCTIONS

- 12 -

Lighting:

NOTE: This heater is equipped with a Pilot Light that allows for safer startups and shutdowns. Pilot MUST be lit

before Main Burner can be started. For initial start or after any cylinder change, hold the control knob in for 2

minutes to purge air from all gas lines before proceeding.

1. Turn the Control Knob to the “OFF” position.

2. Fully open the LP cylinder valve.

3. Open the Viewing Hole by sliding the cover to the left.

4. Push Control Knob in and rotate to Pilot position.

5. Push and release the Igniter Button on the control panel

until flame is visible through Viewing Hole.

6. Release Control Knob after 30-60 seconds. Pilot light will

remain lit. If not, return to Step 1.

7. Turn Control Knob to ON. Main Burner will light immediately.

Flame is visible through Viewing Hole. If not, return to Step 1.

8. To increase the flame, turn the Control Knob counter clockwise

to HI. To decrease the flame, turn the Control Knob clockwise to LO.

If your some reason your igniter fails to deliver a spark, your

heater can be started by inserting a lit match or stick lighter

through the pilot Viewing Hole while pushing the Control Knob

in while it is in the Pilot position.

NOTE: If Pilot fails to remain lit, all valves should be closed and a

waiting period of at least 5 minutes should pass before

attempting to re-light.

9. To turn the appliance OFF, push down the Control Knob and turn

clockwise to the Pilot position. Burner will extinguish but Pilot will remain On. To extinguish Pilot, press in the

Control Knob and continue to turn clockwise to OFF.

7. Wait at least 5 minutes before attempting to re-light the heater.

8. Turn the gas cylinder valve to OFF or closed.

If you experience any ignition problems, please consult “Troubleshooting” on page 15.

Caution: Avoid inhaling fumes emitted from the heater’s first use. Smoke and odor from the burning of oils used in the manufacturing will

appear. Both smoke and odor will dissipate after approximately 30 minutes. The heater should NOT produce thick black smoke.

When Heater is ON:

Emitter screen will become bright red due to intense heat. The color is more visible at night. Burner will display

tongues of blue and yellow flame. These flames should not be yellow or produce thick black smoke, indicating an

obstruction of airflow through the burners. The flame should be blue with straight yellow tops. If excessive yellow

flame is detected, turn off heater and consult “Troubleshooting” on page 15.

Re-Lighting:

Note: For your safety, control knob cannot be turned OFF without first depressing the control knob and then

rotating to OFF.

1. Turn control knob to OFF.

2. Wait at least 5 minutes to allow gas to dissipate before re-lighting.

3. Repeat the “Lighting” steps as listed above.

OPERATING INSTRUCTIONS

- 13 -

Shut Down:

1. Turn Control Knob clockwise to Pilot while depressing the knob (normally, burner will make a slight popping

noise when extinguished.) Burner will extinguish but Pilot will remain lit.

2. To extinguish Pilot, press in Control Knob and continue to turn clockwise to OFF.

2. Turn cylinder valve clockwise to OFF and disconnect regulator when heater is not in use.

NOTE: After use, some discoloration of the emitter screen is normal.

Operation Checklist:

For a safe and pleasurable heating experience, perform this check before each use:

Before Operating:

1. I am familiar with entire owner’s manual and understand all precautions noted.

2. All components are properly assembled, intact and operable.

3. No alterations have been made.

4. All gas connections are secure and do not leak.

5. Wind velocity is below 10 mph.

6. Unit will operate at reduced efficiency below 40 degrees F.

7. Heater is for use outdoors (outside any enclosure).

8. There is adequate fresh air ventilation.

9. Heater is away from gasoline or other flammable liquids or vapors.

10. Heater is away from windows, air intake openings, sprinklers and other water sources.

11. Heater is at least 36 in. on top and at least 24 in. on sides from combustible materials.

12. Heater is on a hard and level surface.

13. There are no signs of spider or insect nests in heater orifices.

14. All burner passages are clear.

15. All air circulation passages are clear.

16. Children and adults should be alerted to the hazards of high surface temperatures and should stay away to

avoid burns or clothing ignition.

17. Young children should be carefully supervised when they are in the area of the heater.

18. Clothing or other protective material should not be hung from the heater, or placed on or near the heater.

19. Any guard or other protective device removed for servicing the heater must be replaced prior to operating

the heater.

20. Installation and repair should be done by a qualified service person. The heater should be inspected before

each use and at least annually by a qualified service person.

21. More frequent cleaning may be required as necessary. It is imperative that control compartment burner and

circulating air passageways of the heater be kept clean and free of debris and/or spider or insect nests.

After Operation:

1. Gas Control Knob is in OFF position.

2. Gas tank valve is OFF.

3. Disconnect gas line.

4. Heater is in upright secure location.

OPERATING INSTRUCTIONS

- 14 -

To enjoy years of outstanding performance from your heater, make sure you perform the following maintenance

activities on a regular basis:

Keep exterior surfaces clean.

1. Use soapy water for cleaning. Never use flammable or corrosive cleaning agents.

2. While cleaning your unit, be sure to keep the area around the burner and control compartment dry at all times.

Do not submerge the control valve assembly. If the gas control is submerged in water, do NOT use it. It must be

replaced.

3. Air flow must be unobstructed. Keep controls, burner, and circulating air passageways clean. Signs of possible

blockage include:

 Gas odor with extreme yellow tipping of flame.

 Heater does NOT reach the desired temperature.

 Heater glow is excessively uneven.

 Heater makes popping noise.

 Spiders and insects can nest in burner or orifices. This dangerous condition can damage heater and

render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help

clear away smaller particles.

 Carbon deposits may create a fire hazard. Clean dome and burner screen with warm soapy water if any

carbon deposits develop.

Note: In a salt-air environment (such as near an ocean), corrosion occurs more quickly than normal. Frequently

check for corroded areas and repair them promptly.

TIP (FOR STAINLESS STEEL MODELS):

Use high-quality automobile wax to help maintain the appearance of your heater. Apply to exterior

surfaces from the post down. DO NOT apply to emitter screen or domes.

Storage:

Between uses:

 Turn Control Knob OFF.

 Disconnect LP source.

 Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet,

hail, snow, dust and debris).

 If desired, cover heater to protect exterior surfaces and to help prevent build-up in air passages. Never

leave LP cylinder exposed to direct sunlight or excessive heat.

Note: Wait until heater is cool before covering.

Service:

Only a qualified service person should repair gas passages and associated components.

Caution: Always allow heater to cool before attempting service.

CARE AND MAINTENANCE

- 15 -

If you have any questions regarding this product, please call our customer service hotline at 1-866-985-7877,

9a.m. – 6 p.m. (EST), Monday – Friday, or email us at cservice@welltraveled.net.

TROUBLESHOOTING

- 16 -

1 YEAR LIMITED WARRANTY – Customers in the Continental US

All components are warranted for a period of 1 year after date of purchase by the original owner against defects in materials

and workmanship under normal use. This warranty does NOT cover normal wear and weathering, assembly and/or

maintenance OR use in a commercial application if model is not designated as a commercial model. At Well Traveled Living’s

sole discretion, products under warranty will be repaired and/or replaced at no charge to the customer. Any returns sent back

to Well Traveled Living must be sent via prepaid freight and in the original retail packaging.

For warranty service contact Well Traveled Living at the address, phone numbers or internet site and email listed in this

owner’s manual. Be sure to have your sales receipt, date of purchase and catalogue/model numbers available when calling. All

warranty service will be coordinated by the Well Traveled Living’s, Amelia Island, Florida service center.

This warranty is extended only to the original purchaser. Proof of purchase will be required before warranty service is rendered.

The sales receipt is the only valid proof of purchase. This warranty only covers failures due to defects in materials or

workmanship which occur during normal use. Failures and/or damage which result from accident, negligence, misuse, abuse,

neglect, mishandling, alteration or modification, failure to maintain, improper assembly or maintenance, service by

unauthorized agency or use of unauthorized components or damage that is attributable to acts of God are NOT covered.

***THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED ABOVE***

***PURCHASER ASSUMES ALL RISKS IN THE ASSEMBLY AND OPERATION OF THIS UNIT***

***FAILURE TO FOLLOW WARNINGS AND OPERATIONAL INSTRUCTIONS CONTAINED IN THIS MANUAL CAN

RESULT IN SEVERE PROPERTY DAMAGE AND/OR PERSONAL INJURY***

IN NO EVENT WILL WELL TRAVELED LIVING, OR ITS DIRECTORS, OFFICERS OR AGENTS BE LIABLE TO THE

PURCHASER OR ANY THIRD PARTY, WHETHER IN CONTRACT, IN TORT, OR ON ANY OTHER BASIS, FOR ANY

INDIRECT, SPECIAL, PUNITIVE, EXEMPLARY, CONSEQUENTIAL, OR INCIDENTAL LOSS, COST, OR DAMAGE

ARISING OUT OF OR IN CONNECTION WITH THE SALE, MAINTENANCE, USE, OR INABILITY TO USE THE PRODUCT,

EVEN IF WELL TRAVELED LIVING OR ITS DIRECTORS, OFFICERS OR AGENTS HAVE BEEN ADVISED OF THE

POSSIBILITY OF SUCH LOSSES, COSTS OR DAMAGES, OR IF SUCH LOSSES, COSTS, OR DAMAGES ARE

FORESEEABLE. IN NO EVENT WILL WELL TRAVELED LIVING, OR ITS OFFICERS, DIRECTORS, OR AGENTS BE

LIABLE FOR ANY DIRECT LOSSES, COSTS OR DAMAGES THAT EXCEED THE PURCHASE PRICE OF THE

PRODUCT.

SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER.

This limited warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to

jurisdiction. The provisions of the United Nations Convention on Contracts for the Sales of Goods shall not apply to this limited

warranty or the sale of products covered by this limited warranty.

Distributed By:

Well Traveled Living

716 S 8

th

Street

Amelia Island, FL 32034

Toll Free: 866-WTL-SUPP

(866-985-7877)

Web: www.wtliving.com

Email: cservice@welltraveled.net

***IMPORTANT NOTICE***

-Do NOT return to place of purchase-

For customer service and warranty issues

contact our Customer Service Center at:

(866)-985-7877 OR

Email: cservice@welltraveled.net

Customer Service Hours: Mon. – Fri. 9:00 a.m. – 6:00 p.m.

(EST)

Fire Sense®, Mojave Sun ®, and Well Traveled Living® are registered trademarks of Well Traveled Imports, Inc®. All

assembly instruction presentations are the property of Well Traveled Imports, Inc.® and are protected by U.S. copyrights

Fire Sense 61279 Owner's manual

Fire Sense 61279 Owner's manual

Related papers

Other documents