John Lewis JLWM1414 Quick start guide

John Lewis
Brand
John Lewis
Model
JLWM1414
Category
Washing machines
Type
Quick start guide

This manual is also suitable for

Quick User’s Guide
The On/Off button with AUTO Stand-by function
The Stand-by function automatically deactivates the appliance to decrease energy consumption when:
• Before you press Start/Pause button, if you do not use the appliance for about fi ve
minutes. All settings are cancelled. Press On/Off button to activate it again.
• After 5 minutes from the end of the washing programme. Once activated the ap-
Before you activate the appliance read
the Safety Information chapter in the
user manual.
For more information please always
refer to the user manual.
The detergent dispenser
Compartment for prewash or intensive phase
Compartment for the wash phase
Liquid additives compartment
Flap for powder (position up) or liquid detergent
1. On/Off button
2. Programme knob
3. Display
5. Delay start button
Control Panel
4. Start/Pause button
(position down)
1 2 3
4
56910 8 7
8. Intensive button
9.
Spin reduction button
10. Temperature button
7. Extra rinse button
6. Quick button
pliance again, the display shows the end of the cycle.
Interactive display
The simple and logic display gives immediately all the information about the washing
ALARM
CODES
The display can show alarm codes (refer to
“Troubleshooting” in the user manual):
-
: The appliance does not fill water properly.
-
: The appliance does not drain the water.
-
: The appliance door is open or not closed correctly.
-
: The anti-flood device is on. Disconnect the appliance
and close the water tap.
programme.
THE
OPTISENSE
WASH
The appliance adjusts automatically the cycle time to the
laundry load to have PERFECT
washing result in minimum necessary time. The dot flashes (e.g. ).
After about 15 minutes from the start of the programme, the
display shows the new
D
The temperature value.
The spin speed value, No Spin ( )
Rinse Hold ( ) function.
C. The washing phase symbols
- Washing phase
- Rinse phase
- Spin phase
- Child lock
- Door
A.
B.
You cannot open the appliance door when
the symbol is on.
only when this
symbol goes off.
If the programme is completed but the symbol stays on:
- There is water in the drum.
- The Rinse Hold function is on.
D. The
digit area:
- The washing programme duration.
- The Delay Start set.
- The alarm codes.
Err
- The messagge when you make
- The end of the programme ( ).
1 Only available for Spin/Drain programme.
2 The symbols appear on the display when the related phase
or function is set.
time value. The dot stops flashing (e.g. ).
a wrong selection.
- Delay start
You can open the door
A
B
C
Contact the service centre.
1
2
DAILY USE
1. Open the water tap and connect the
mains plug to the mains socket.
2. Press On/Off button to activate the
appliance.
3. Put the laundry in the drum, one item
at a time. Make sure that no laundry
stays between the seal and the door.
4. Close the door.
5. Put the detergent and additives in the
correct compartment of the dispenser.
6. Turn the programme knob to set a
programme.The corresponding
indicator comes on.
7. The display shows the default
temperature and maximum spin speed.
To change the default values or to set
functions press the corresponding
buttons.
8. If necessary, set the delay start
function. Press Delay Start button
repeatedly until the display shows the
desired delay time.
9. Press Start/Pause button to start the
washing programme. If you set the
Delay Start, the appliance starts the
countdown.
10. At the end of the programme the
display shows a zero , the symbol of
the last washing phase is on.
The indicator of the Start/Pause button
and the door lock symbol go off. If you
set the Rinse Hold function, refer to ‘At
the end of the programme’ chapter in
the user manual.
11. Unplug the appliance and close the
water tap.
AFTER PROGRAMME START
Cancel the Delay Start
1. Press Start/Pause button.
2. Press Delay Start button until the
display shows a zero.
3. Press Start/Pause button.The
programme starts.
Interrupt a programme and/or
change a function
1. Press Start/Pause button. Now you can
change the function set.The Time Save
cannot be set in this case.
2. Press Start/Pause button.The
programme continues.
Clean the appliance filter regularly. Refer to
“Care and Cleaning” chapter in the user manual.
CARE AND CLEANING
Quick Guide S7 132906750.qxd 25/03/2014 15:27 Page 3
Start the appliance
Programmes
Programme Temperature Type of load
Cottons
95º - Cold White and coloured cotton items
Synthetics
60º - Cold Synthetic or mixed fabric items
Easy Iron
60º - Cold Synthetic items
Delicates
40º - Cold Delicate fabrics as acrylics, viscose, polyester items
Wool/Silk
40º - Cold Fabrics with “hand washing” and “wool” c are symbols
20 Minute wash
40º - 30º Cotton and synthetic items with light soil or worn
Rinse
Cold All fabrics
Spin/Drain
/ The spin assumes the setting for cottons
Heavy cotton
Intensive
Cool wash
Cold Mixed fabrics (cotton and synthetic items)
Cottons
60° - 40° White and fast coloured cotton with normal soil.
Functions
For each programmes the display shows all the available functions.
In case of incorrect selection, the display tells that the selection is not possible.
132904000-A-192014
60° - 40° Coloured cotton and mixed fabric with normal soil.
60º - Cold Items in denim and jersey.
Lingerie
40º - Cold Very delicate items as lingerie, bras and underwear
with Prewash
60º - Cold Synthetic or mixed fabric items with heavy soil.
with Prewash
95º - Cold White and coloured cotton items with heavy soil
Quiet
95º - Cold White and coloured cotton items. No spinning phases.
economy
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

John Lewis JLWM1414 Quick start guide

John Lewis
Brand
John Lewis
Model
JLWM1414
Category
Washing machines
Type
Quick start guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents