Samsung SDH-B3020 User manual

4/8/16 CHANNEL DVR

User Manual

SDS-P3042/P4042/P4082/P5082/P5102/P5122

Copyright

Trademark

is the registered logo of Samsung Techwin Co., Ltd.

The name of this product is the registered trademark of Samsung Techwin Co., Ltd.

Other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall be reproduced,

distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.

Disclaimer

Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be

provided. Use of this document and the subsequent results shall be entirely on the user's own responsibility. Samsung Techwin reserves the

right to change the contents of this document without prior notice.



Design and specifications are subject to change without prior notice.



The initial administrator ID is “admin” and the password should be set when logging in for the first time.

Set password for your wireless network if you use the product with a wireless router. Being not protected with password or

using the default wireless router password may expose your video data to potential threat.

Please change your password every three months to safely protect personal information and to prevent the damage of the

information theft.

Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.

4/8/16 Channel DVR

User Manual

English _3

! overview

IMPORTANT SAFETY INSTRUCTIONS

Read these operating instructions carefully before using the unit.

Follow all the safety instructions listed below.

Keep these operating instructions handy for future reference.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two

blades with one wider than the other. A grounding type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit

into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods

of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been dropped.

overview

4_ overview

overview

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within

this unit.

This exclamation point symbol is intended to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

•

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

•

To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation

instructions.

WARNING

1. Be sure to use only the standard adapter that is specified in the specification sheet.

Using any other adapter could cause fire, electrical shock, or damage to the product.

2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or

damage to the product.

3. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.

4. When installing the camera, fasten it securely and firmly. The fall of camera may cause personal injury.

5. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on

top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.

6. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.

7. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately

disconnect the power source and contact the service center. Continued use in such a condition may cause fire

or electric shock.

8. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this

product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted

repair.)

9. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.

10. Do not expose the product to the direct airflow from an air conditioner.

Otherwise, it may cause moisture condensation inside the Clear Dome due to temperature difference between

internal and external of the dome camera.

11. If you install this product in a low-temp area such as inside a cold store, you must seal up the wiring pipe with

silicon, so that the external air can not flow inside the housing.

Otherwise, external high, humid air may flow inside the housing, pooling moisture or vapor inside the product

due to a difference between internal and external temperature.

English _5

! overview

BEFORE START

This user manual provides Information for using the DVR such as brief introduction, part names, functions, connection

to other equipment, menu setup, etc.

You have to keep in mind the following notices :

• SAMSUNG retains the copyright on this manual.

• This manual cannot be copied without SAMSUNG’s prior written approval.

• We are not liable for any or all losses to the product incurred by your use of non-standard product or violation

of instructions mentioned in this manual.

• Prior to opening the case, please consult a qualified technician first. Whenever this is needed power must be

removed from the unit.

• Before installing an additional HDD or connecting an external storage device (USB HDD) to this DVR, check the

compatibility. Consult your provider for the compatibility list.

Warning

❖ Battery

It is essential that when changing the battery in the unit, the replacement battery must be of the same type

otherwise there may be a possibility of an explosion.

The following are the specifications of the battery you are using now.

• Normal voltage : 3V

• Normal capacity : 170mAh

• Continuous standard load : 0.2mA

• Operating temperature : -20°C ~ +85°C

(-4°F ~ +185°F)

Caution

• Connect the power cord into a grounded outlet.

• The Mains plug is used as a disconnect device and shall stay readily operable at any time.

• Batteries shall not be exposed to excessive heat such as sunshine, fire or the like

• Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the

Instructions.

❖ System Shutdown

Turning off the power while the product is in operation, or undertaking improper actions may cause damage

or malfunction to the hard drive or the product.

Please turn off the power, please right-click to display the context sensitive menu and select <Shutdown>.

After selecting <OK> in the pop-up menu, you can pull off the power cord.

You may want to install a UPS system for safe operation in order to prevent damage caused by an

unexpected power stoppage. (Any questions concerning UPS, consult your UPS retailer.)

❖ Operating Temperature

The guaranteed operating temperature range of this product is 0°C ~ 40°C (32°F ~ 104°F).

This product may not work properly if you run right after a long period of storage at a temperature below the

guaranteed one.

Prior to using a device that has been stored for a long period in low temperatures, allow the product to stand

at room temperature for a period.

Especially for the built-in HDD in the product, its guaranteed temperature range is 5°C ~ 55°C (41°F ~ 131°F).

Likewise, the hard drive may not work at a temperature below the guaranteed one.

❖ Ethernet Port

DVR is designed for indoor use only and all the communication wirings are limited to inside of the building.

CALIFORNIA USA ONLY

This Perchlorate warning applies only to primary CR (Manganese Dioxide)

Lithium coin cells in the product sold or distributed ONLY in California USA.

“Perchlorate Material - special handling may apply, See www.dtsc.ca.gov/

hazardouswaste/perchlorate.”

6_ overview

over

view

ConTenTS

over

v

IeW

3

3 Important Safety Instructions

5 Befor

e Start

6

Contents

8

Featur

es

10

Part Names and Functions (Fr

ont)

11

Part Names and Functions (Rear)

12 Remote Contr

ol

ConneCTInG WITh oTher devICe

14

14 installation

14 Checking the Installation Envir

onment

15

Connecting External Devices

15 Connecting the USB

15

Connecting Exter

nal SATA HDD

16

Connecting the Camera (SDC-7340BC)

18 Connecting the RS-485 Device

18 Connecting the Network

LIve

20

20 Getting Started

22 Live Screen Configuration

27 Live Mode

30 Zoom

30 Audio On/Off

30 Freeze

31 Event Monitoring

mAIn menu

32

32 System Setup

44 Setting the Device

53 Setting the Recor

ding

56

Setting the Event

58 Backup

60 Network Configuration

73 Contr

olling a PTZ Device

English _7

! overview

SEARCH & PLAY

76

76 Search

79 Playback

WEB VIEWER

81

81 Introducing Web Viewer

82 Connecting Web Viewer (Windows)

84 Using Live Viewer (Windows)

92 Using Search Viewer

95 Viewer Setup

106 About

107 Connecting Web Viewer (Mac)

108 Using Live Viewer (Mac)

110 Mobile Viewer

BACKUP VIEWER

111

111 SEC Backup Viewer

APPENDIX

113

113 Product Specification (Camera)

114 Product Specification(DVR)

120 Product Overview

123 Default Setting

126 Troubleshooting

129 Open Source License Report on the Product

8_ overview

overview

FEATURES

The DVR employs H.264 video encoding for 4, 8 or 16 channel inputs and G.711 audio encoding for 4, 8 or 16

channels while simultaneously supports hard disc recording and playback.

These DVRs also supports network connectivity, providing remote monitoring from a remote PC transferring video

and audio data.

•

Provides a convenient User Interface

•

4/8/16 CH Composite Input Connectors

•

Supports WD1/CIF/2CIF/4CIF recording formats

•

With the network specific codec, network transfer enabled regardless of the recording conditions

•

De-interlacing processor for better picture quality

•

Display of HDD information and status by using HDD SMART

•

Hard Disk overwrite function

•

Mass storage hard disk backup through high-speed USB 2.0

•

Simultaneous Record and Playback of 4/8/16-channel video data

•

Various Search Modes (Search by Time, Event, Backup and Motion Detection)

•

Various Recording Modes (Manual, Event, Scheduled Recording)

•

Alarm Interface

•

Remote Monitoring function by Network Viewer, Smart Viewer and Mobile Viewer

Standards Approvals

M

`

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the interference at

his own expense.

English _9

! OVER

VIEW

Package Contents

Please unwrap the pr

oduct, and place the product on a flat place or in the place to be installed.

Please check the following contents are included in addition to the main unit.

POWER REC NETWORK

DVR (1SET) Ada

pter * / Power Cable * Mouse (1EA)

Remote Control (1EA) / Ba

ttery (2EA) SDC-7340BC * Camera Cable * (

60FT or 90FT

)

Camera Power Cable*

(5 splitter or 9 splitter)

Network Cable (1EA) HDMI Cable(1EA)

Expansion pipe and Screw * Manual CD (1EA) Quick Start Guide (1EA)

W

arranty Card (1EA)

M

odel SDC-7340BC Adapter/Power cable Camera Cable

Expansion pipe and Screw

Camera Power ca

ble

SDS-P3042 4EA 1EA 60FT: 4EA 12EA/12EA 5 splitter 1EA

SDS-P4042 4EA 1EA 60FT: 4EA 12EA/12EA 9 splitter 1EA

SDS-P4082 8EA 1EA 60FT: 6EA, 90FT: 2EA 24EA/24EA 9 splitter 1EA

SDS-P5082 8EA 2EA 60FT: 6EA, 90FT: 2EA 24EA/24EA 5 splitter 1EA

9 splitter 1EA

SDS-P5102 10EA 2EA 60FT: 8EA, 90FT: 2EA 30EA/30EA 5 splitter 1EA

9 splitter 1EA

SDS-P5122 12EA 2EA 60FT: 9EA, 90FT: 3EA 36EA/36EA 5 splitter 1EA

9 splitter 1EA

10_ overview

overview

PART NAMES AND FUNCTIONS (FRONT)

Part Names Functions

a

USB Port Connects the USB devices.

b

Remote Control

Receiver

Input the remote control signal.

c

LED Indicator

POWER : Displays the power ON/OFF status.

REC : Lights on when recording is in progress.

NETWORK : Displays both network connection and data transfer status.

M

`

All functions are operable with mouse control, since there are no front buttons.

POWER REC NETWORK

a

c

b

English _11

! overview

PART NAMES AND FUNCTIONS (REAR)

SDR-5102

SDR-4102

SDR-3102

Part Names Functions

a

VIDEO IN Input port for the composite video signal.

b

AUDIO IN Input ports (RCA jack) for the audio signal.

c

VGA OUT Output port for VGA video signal.

d

e-SATA Ports used for external storage device connections.

e

NETWORK NETWORK connector port.

f

DC 12V DVR power input port.

g

USB USB connector port.

h

RS-485 Used to establish RS-485 communications.

i

HDMI HDMI connector port.

j

AUDIO OUT Output port (RCA jack) for the audio signal.

VGA

LAN

RS485

IN1

CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8

CH9 CH10 CH11 CH12 CH13 CH14 CH15

IN2

IN3 IN4

AUDIO INVIDEO IN

HDMI DC 12 V

USB

eS ATA

AUDIO OUT

CH16

VGA

LAN

RS485

IN1

CH1 CH2 CH3 CH4

CH5 CH6 CH7 CH8

IN2

IN3 IN4

AUDIO INVIDEO IN

HDMI DC 12 V

USB

eS ATA

AUDIO OUT

VGA

LAN

RS485

IN1

CH1 CH2

CH3 CH4

IN2

IN3 IN4

AUDIO INVIDEO IN

HDMI DC 12 V

USB

eS ATA

AUDIO OUT

VGA

LAN

RS485

IN1

CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8

CH9 CH10 CH11 CH12 CH13 CH14 CH15

IN2

IN3 IN4

AUDIO INVIDEO IN

HDMI DC 12 V

USB

eS ATA

AUDIO OUT

CH16

VGA

LAN

RS485

IN1

CH1 CH2 CH3 CH4

CH5 CH6 CH7 CH8

IN2

IN3 IN4

AUDIO INVIDEO IN

HDMI DC 12 V

USB

eS ATA

AUDIO OUT

VGA

LAN

RS485

IN1

CH1 CH2

CH3 CH4

IN2

IN3 IN4

AUDIO INVIDEO IN

HDMI DC 12 V

USB

eS ATA

AUDIO OUT

a

b

c

d e

fghij

a b

c

e d

f

hgij

VGA

LAN

RS485

IN1

CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8

CH9 CH10 CH11 CH12 CH13 CH14 CH15

IN2

IN3 IN4

AUDIO INVIDEO IN

HDMI DC 12 V

USB

eS ATA

AUDIO OUT

CH16

VGA

LAN

RS485

IN1

CH1 CH2 CH3 CH4

CH5 CH6 CH7 CH8

IN2

IN3 IN4

AUDIO INVIDEO IN

HDMI DC 12 V

USB

eS ATA

AUDIO OUT

VGA

LAN

RS485

IN1

CH1 CH2

CH3 CH4

IN2

IN3 IN4

AUDIO INVIDEO IN

HDMI DC 12 V

USB

eS ATA

AUDIO OUT

j

f

hgi

a

b

c

e d

12_ overview

overview

REMOTE CONTROL

SEARCH

Displays the search menu.

POWER

Displays the Exit pop up screen.

NUMBER [0~+10]

Used as the numeric input keys, or displays a single

channel.

T/W

Zooms in or out.

BACKUP

Displays the Backup Menu.

MODE

Changes the screen mode.

MENU

Goes to the system menu screen.

Up/Down/Left/Right(

$%_ +

)/ENTER

Moves the cursor up/down/left/right, and runs the

Select Menu.

FREEZE

Freezes the screen temporarily.

ZOOM

Runs the digital zoom (x2) function.

DVR

Activates the DVR function.

ID

Sets the ID of the system.

Select 2 digits from 0 ~ 9 while pressing the ID Key.

SCROLL

,.

Moves the menu scroll.

RETURN

Returns to the previous screen.

AUDIO

Turns Audio on/off.

ALARM

Cancels the Alarm.

REC LOCK

Selects the recording lock function.

REC

Starts or ends the live recording.

Skip Backward (by unit time),

Slow Rewind, Slow Forward,

Skip Forward (by unit time)

Move Frame

While paused, moves to the previous/next frame.

FR, STOP, PLAY/PAUSE, FF

PRESET

Displays the Preset Setup.

Using the numeric buttons

CHANNEL 1–9 Press each button between 1 to 9. (8CH : 8)

CHANNEL 10 Press the [0/+10] button first, then press the [0/+10] within 1 second.

CHANNEL 11–16 Press the [0/+10] button first, then press any number between 1 to 6.

PTZ

Displays or ends PTZ.

VIEW

Runs the View function in the PTZ mode.

English _13

! overview

Changing the Remote Control ID

1. Press the [ID] button of the remote control and check the ID displayed on the DVR screen.

The factory default ID of the remote control is 00.

2. Enter 2 digits of your selection in order, while pressing the system [ID] button.

3. When ID input is done, press the system [ID] button again to check the setting.

M

`

If you want to change the remote control ID to 08: Press 0 and 8 in order while the system [ID] button is pressed.

Remote control's ID and DVR’s ID should be matched for proper operation. Refer to “Remote Devices”. (Page 50)

14_ connecting with other device

connecting with other device

One Year: 24HR X 365 DAY =8,760 HR

Temperature

Unit: ºC

Life (Unit: HOURS)

INSTALLATION

Please take note of the followings before using this product.

•

Do not use the product outdoor.

•

Do not spill water or liquid in the connection part of the product.

•

Do not impose the system to excessive shock or force.

•

Do not pull out the power plug forcefully.

•

Do not disassemble the product on your own.

•

Do not exceed the rated input/output range.

•

Use a certified power cord only.

•

For the product with an input ground, use a grounded power plug.

CHECKING THE INSTALLATION ENVIRONMENT

Samsung Digital Video Recorder (“DVR” hereinafter) is a state-

of-art security device, and contains mass storage hard disk(s)

and critical circuits inside.

When the temperature rises inside the product, the product may

breakdown and the product life be shortened. Please pay

attention to the following recommendations before installation.

The followings are the recommendations when Samsung DVR is installed on a rack.

1. Please ensure that the rack inside is not sealed.

2. Please ensure the air is circulated through the inlet/outlet as shown in the picture.

3. If the DVR or other devices on a rack is to be stacked as in the picture, provide a

suitable space or install a ventilating opening for air circulation.

4. For natural air convection, place the inlet at the bottom of the rack and the outlet on top.

5. It is strongly recommended that a fan motor is installed at the inlet and the outlet for air

circulation. (Please fit a filter at the inlet to screen dust or foreign substances.)

6. Please maintain the temperature inside the rack or surrounding areas between

0°C ~ 40°C (32°F ~ 104°F) as shown in the figure 1.

Rack Mount Instructions - The following or similar rack-mount instructions are

included with the installation instructions :

A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the

operating ambient temperature of the rack environment may be greater than room

ambient. Therefore, consideration should be given to installing the equipment in an

environment compatible with the maximum ambient temperature specified by the

manufacturer.

B) Reduced Air Flow - Installation of the equipment in a rack should be such that the

amount of air flow required for safe operation of the equipment is not compromised.

C) Mechanical Loading - Mounting of the equipment in the rack should be such that a

hazardous condition is not achieved due to uneven mechanical loading.

D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply

circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring.

Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.

E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should

be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).

[Figure 1]

[Figure 2]

[Figure 1]

[Figure 2]

English _15

! CONNECTING WITH OTHER DEVICE

CONNECTING EXTERNAL DEVICES

CONNECTING THE USB

1. By factory default, a USB port is provided for external connection.

2. You can connect a USB HDD, USB memory or mouse to the USB port.

3. If a USB HDD is connected to the system, recognition and settings are available in “Main Menu > Setting the

Device > Storage Device”. (Page 47)

4. This product supports hot-plugging, which connects/removes the USB device during the system operation.

J

`

If you use the USB device for Backup purposes, format it with FAT32 on PC if it is not formatted on the DVR.

CONNECTING EXTERNAL SATA HDD (ESATA)

External SATA port is provided on the rear panel.

If connected to the system, the external SATA HDD (eSATA) can be recognized and configured in “Main Menu >

Device > Storage Device”.

J

`

Use a cable shorter than 1 m for the external external SATA HDD (eSATA) connections.

`

Unexpected disconnection to a device in use which is connected via eSATA may restart the system. Check whether the

device is in use before disconnecting it.

`

In the event of replacing an HDD of an external SATA HDD, please power off the external SATA HDD to change the HDD.

CONSOLE

AUDIO IN

CH1

CH2

VGA OUT

DC 12V

NETWORK

AUDIO IN

VIDEO IN

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

CH3

CH4

AUDIO OUT

+ -

RS 485

IN1

IN3

IN4

AUDIO IN

AUDIO OUT

VGA

LAN

RS485

IN2

HDMI

DC 12 V

USB

eSATA

VIDEO IN

16_ connecting with other device

connecting with other device

CONNECTING THE CAMERA (SDC-7340BC)

Equipped with the IR LED and the illumination sensor, enables you to monitor at night as well as in daytime.

The camera is suitable for both internal and external use.

`

Please make sure not to fully expose the camera to rain. The camera must be installed under a shelter to avoid exposure to excessive rain

or moisture.

Name Description

a

IR LED These infrared LED's are controlled by the illumination sensor.

b

Lens

Focal length of 3.6mm enables you to cover relatively longer range of monitoring.

c

Illumination Sensor Detects incoming light to control the IR LED.

d

BNC Cable BNC terminal for video signal output.

e

Power Cable Used to plug the power cable.

d

e

a

b

c

English _17

! CONNECTING WITH OTHER DEVICE

Connecting with DVR

`

The following figures are based on Model SDR-5102.

Installing the camera

The camera can be installed on the wall, ceiling, shelf or a desired position using the provided bracket.

1. Select a position where you want to install the camera.

`

Make sure the selected position can sustain the weight of the camera.

2. Attach the camera bracket to the wall using the supplied screws.

•

SDC-7340BC : M4 X L20

3. Adjust the camera to target the video location and tighten the camera bracket handle on the camera

bracket.

4. Connect the camera cable to the camera.

J

`

You should be careful when installing the camera outdoors because the cable connectors may be wet with moisture or pile

up with impurities.

`

The camera satisfies the IP66 standard, and direct exposure to water or moisture may cause problem such as

condensation.

IN1

IN3

IN4

AUDIO IN

AUDIO OUT

VGA

LAN

RS485

IN2

HDMI

DC 12 V

USB

eSATA

VIDEO IN

M4 X L20

sized screws

wall or ceiling

Handle

18_ connecting with other device

connecting with other device

CONNECTING THE RS-485 DEVICE

Connect the rear [RS-485 +, –] port to the PTZ camera.

J

`

You can connect and control the PTZ camera which supports the RS-485 communication.

`

Check if the RS-485 device is compatible with the product first.

`

Pay attention not to change the polarity (+/-) of the RS-485 device when connecting it.

`

Depending on camera’s type, connection polarity can be different. For further information,

refer to the respective PTZ Camera’s documentation.

CONNECTING THE NETWORK

`

The following figures are based on Model SDR-5102.

Connecting to network through Ethernet (10/100BaseT)

RS485

IN1

IN3

IN4

AUDIO IN

AUDIO OUT

VGA

LAN

RS485

IN2

HDMI

DC 12 V

USB

eSATA

VIDEO IN

RJ-45 Ethernet Cable

(Direct Cable)

Back Bone

Hub/Switcher

Windows

Network Viewer

NETWORK

English _19

! CONNECTING WITH OTHER DEVICE

Connecting to the Network using the router

Connecting to Network through ADSL

IN1

IN3

IN4

AUDIO IN

AUDIO OUT

VGA

LAN

RS485

IN2

HDMI

DC 12 V

USB

eSATA

VIDEO IN

Broadband Router

xDSL or Cable Modem

External

Remote PC

DDNS Server

(Data Center)

NETWORK

xDSL or Cable Modem

IN1

IN3

IN4

AUDIO IN

AUDIO OUT

VGA

LAN

RS485

IN2

HDMI

DC 12 V

USB

eSATA

VIDEO IN

NETWORK

RJ-45 Ethernet Cable

(Direct Cable)

Phone(ADSL) Line

ADSL MODEM

Hub/Switcher

Windows

Network Viewer

20_ live

live

GETTING STARTED

Starting the system

1. Connect the power cable of the DVR to the wall outlet.

M

`

It takes about 10 seconds to display the start screen after

booting.

2. You will see the initialization screen.

The initialization process will last about 1 minute.

If a new HDD is installed, the initialization process may

take longer.

3. The live screen appears with a beep.

Shutting Down the System

You can shut down the system only if you have logged in to the DVR.

You require permission to shut down the system if you are not logged in as admin.

1. Press the [POWER] button on the remote control, or

right-click to display the context sensitive menu and select

<Shutdown>.

2. The “Shutdown” confirmation window appears.

3. Use the arrow keys on the remote control to move to

<OK> and press the [ENTER] button or click <OK>. The

system will shut down.

M

`

For the permission management, refer to “Permission

Management > Setting Permissions”. (Page 39)

REC

2013-01-01 01:10:25

2013-01-01

01:10:25

2013-01-01 01:10:25

2013-01-01

01:10:25

Shutdown

Are you sure to shutdown?

OK Cancel

Page is loading ...

Samsung SDH-B3020 User manual

Samsung SDH-B3020 User manual

Related papers

Other documents