Mitsubishi XD590U User manual

Category
Data projectors
Type
User manual
DLP PROJECTOR
MODEL
XD590U
User Manual
This User Manual is important to you.
Please read it before using your projector.
ENGLISH
EN-2
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsu-
lated "dangerous voltage" within the products enclosure that may be of sufficient magnitude to constitute a risk of electric
shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING
Use the attached specified power supply cord. If you use another
power supply cord, it may cause interference with radio and television
reception.
Use the attached RGB cable and the shielded LAN cable with this
equipment so as to keep interference within the limits of an FCC
Class B device.
This apparatus must be grounded.
DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE
PROJECTOR IS IN THE POWER ON MODE.
CAUTION
Not for use in a computer room as defined in the Standard for the
Protection of Electronic Computer/Data Processing Equipment,
ANSI/NFPA 75.
The attached power cord is to be used exclusively for this product.
Never use it for other products.
When using the projector in Europe:
COMPLIANCE NOTICE
This Projector complies with the requirements of the EC Directive
2004/108/EC "EMC Directive" and 2006/95/EC "Low Voltage Direc-
tive".
The electro-magnetic susceptibility has been chosen at a level that
gains proper operation in residential areas, on business and light
industrial premises and on small-scale enterprises, inside as well as
outside of the buildings. All places of operation are characterized by
their connection to the public low voltage power supply system.
WARNING
Use the attached RGB cable and the shielded LAN cable with this
equipment so as to keep interference within the limits of an EN55022
Class B device.
Please follow WARNING instructions.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION:
TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUT-
LET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
NOTE:
SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND
SHALL BE EASILY ACCESSIBLE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Note: This symbol mark is for
EU countries only.
This symbol mark is according to
the directive 2002/96/EC Article
10 Information for users and
Annex IV, and/or to the directive
2006/66/EC Article 20 Informa-
tion for end-users and Annex II.
Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality
materials and components which can be recycled and/or reused.
This symbol means that electrical and electronic equipment, batteries and accumula-
tors, at their end-of-life, should be disposed of separately from your household waste.
If a chemical symbol is printed beneath the symbol shown above, this chemical symbol
means that the battery or accumulator contains a heavy metal at a certain concentra-
tion. This will be indicated as follows:
Hg: mercury (0,0005%), Cd: cadmium (0,002%), Pb: lead (0,004%)
In the European Union there are separate collection systems for used electrical and
electronic products, batteries and accumulators.
Please, dispose of this equipment, batteries and accumulators correctly at your local
community waste collection/recycling centre.
Please, help us to conserve the environment we live in!
EN-3
ENGLISH
Contents
Important safeguards................................................................................................................................ 4
Overview...................................................................................................................................................6
Remote control .....................................................................................................................................7, 8
Installation ................................................................................................................................................9
Basic connections...................................................................................................................................10
Preparation .............................................................................................................................................13
Basic operation.......................................................................................................................................14
Menu operation.......................................................................................................................................18
Image adjustment ...................................................................................................................................26
Network settings .....................................................................................................................................28
Advanced features..................................................................................................................................31
Lamp replacement..................................................................................................................................34
Troubleshooting ......................................................................................................................................36
Indicators ................................................................................................................................................39
Specifications .........................................................................................................................................40
Trademark, Registered trademark
Macintosh is registered trademark of Apple Computer Inc.
DLP
TM
, Digital Micromirror Device, DMD, and BrilliantColor
TM
are all trademarks of Texas Instruments.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
Microsoft, Windows, Windows 2000, Windows XP, Windows Vista, and Internet Explorer are registered trademarks, trademarks, or trade names of
Microsoft Corporation in the U.S. and/or other countries.
Other brand or product names are trademarks or registered trademarks of their respective holders.
Declaration of Conformity
Model Number : XD590U
Trade Name : MITSUBISHI ELECTRIC
Responsible party : Mitsubishi Digital Electronics America, Inc.
9351 Jeronimo Road, Irvine, CA 92618 U.S.A
Telephone number : +1-(949) 465-6000
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
EN-4
Important safeguards
Please read all these instructions regarding your projector and retain
them for future reference. Follow all warnings and instructions marked
on the projector.
1. Read instructions
All the safety and operating instructions should be read before
the appliance is operated.
2. Retain instructions
The safety and operating instructions should be retained for
future reference.
3. Warnings
All warnings on the appliance and in the operating instructions
should be adhered to.
4. Instructions
All operating instructions must be followed.
5. Cleaning
Unplug this projector from the wall outlet before cleaning it. Do
not use liquid aerosol cleaners. Use a damp soft cloth for clean-
ing.
6. Attachments and equipment
Never add any attachments and/or equipment without the
approval of the manufacturer as such additions may result in the
risk of fire, electric shock or other personal injury.
7. Water and moisture
Do not use this projector near water or in contact with water.
8. Accessories
Do not place this projector on an unstable cart, stand, tripod,
bracket or table. Use only with a cart, stand, tripod bracket, or
table recommended by the manufacturer or sold with the projec-
tor. Any mounting of the appliance should follow the manufac-
turer’s instructions and should use a mounting accessory
recommended by the manufacturer.
An appliance and cart combination should be moved with care.
Quick stops, excessive force and uneven surfaces may cause
the appliance and cart combination to overturn.
9. Ventilation
Slots and openings in the cabinet are provided for ventilation,
ensuring reliable operation of the projector and to protect it from
overheating. Do not block these openings or allow them to be
blocked by placing the projector on a bed, sofa, rug, or book-
case. Ensure that there is adequate ventilation and that the man-
ufacturer’s instructions have been adhered to.
10. Power sources
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of the
type of power, please consult your appliance dealer or local
power company.
11. Power-cord protection
Power-supply cords should be routed so that they are not likely
to be walked on or pinched by items placed upon or against
them. Pay particular attention to cords at plugs, convenience
receptacles, and points where they exit from the appliance. Do
not put the power cord under a carpet.
12. Overloading
Do not overload wall outlets and extension cords as this can
result in a fire or electric shock.
13. Objects and liquids
Never push objects of any kind through openings of this projec-
tor as they may touch dangerous voltage points or short-out
parts that could result in a fire or electric shock. Never spill liquid
of any kind on the projector.
14. Servicing
Do not attempt to service this projector yourself. Refer all servic-
ing to qualified service personnel.
15. Damage requiring service
Unplug this projector from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
(a) If the power-supply cord or plug is damaged.
(b) If liquid has been spilled, or objects have fallen into the pro-
jector.
(c) If the projector does not operate normally after you follow
the operating instructions. Adjust only those controls that
are covered by the operating instructions. An improper
adjustment of other controls may result in damage and may
often require extensive work by a qualified technician to
restore the projector to its normal operation.
(d) If the projector has been exposed to rain or water.
(e) If the projector has been dropped or the cabinet has been
damaged.
(f) If the projector exhibits a distinct change in performance -
this indicates a need for service.
16. Replacement parts
When replacement parts are required, be sure that the service
technician has used replacement parts specified by the manu-
facturer or parts having the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock
or other hazards.
17. Safety check
Upon completion of any service or repair to this projector, ask
the service technician to perform safety checks determining that
the projector is in a safe operating condition.
EN-5
ENGLISH
WARNING:
Unplug immediately if there is something wrong with
your projector.
Do not operate if smoke, strange noise or odor comes out of your pro-
jector. It may cause fire or electric shock. In this case, unplug immedi-
ately and contact your dealer.
Never remove the cabinet.
This projector contains high voltage circuitry. An inadvertent contact
may result in an electric shock. Except as specifically explained in
User Manual, do not attempt to service this product by yourself.
Please contact your dealer when you want to fix, adjust, or inspect the
projector.
Do not modify the projector.
It can lead to fire or electric shock.
Do not keep using the damaged projector.
If the projector is dropped and the cabinet is damaged, unplug the
projector and contact your dealer for inspection. It may lead to fire if
you keep using the damaged projector.
Do not face the projection lens to the sun.
It can lead to fire.
Use correct voltage.
If you use incorrect voltage, it can lead to fire.
Do not place the projector on uneven surface.
Place the projector on a level and stable surface only.
Do not look into the lens when the projector is operating.
It may hurt your eyes. Never let children look into the lens when the
projector is on.
Do not unplug the power cord during operation.
It can lead to lamp breakage, fire, electric shock or other trouble. Wait
for the fan to stop before unplugging the power cord.
Do not touch the air outlet grilles and bottom plate.
Do not touch them or put other equipment close to the air outlet grilles
because they become hot during operation. The heated air outlet
grilles and bottom plate may cause injury or damage to other equip-
ment. Also, do not put the projector on a desk that is easily affected by
heat.
Do not look into the air outlet grilles when projector is
operating.
Heat, dust, etc. may blow out of them and hurt your eyes.
Do not block the air inlet and outlet grilles.
If they are blocked, heat may be generated inside the projector, caus-
ing deterioration in the projector quality and fire.
Do not use flammable solvents (benzene, thinner, etc.)
and flammable aerosols near the projector.
Flammable substances may ignite causing fire or breakdown because
the temperature inside the projector rises very high while the lamp is
illuminating.
Do not use the projector with condensation on it.
It can lead to breakdown or other failure.
Place of installation
For safety’s sake, do not use the projector at any place subjected to
high temperature and high humidity. Please maintain an operating
temperature, humidity, and altitude as specified below.
Operating temperature: between +41°F (+5°C) and +95°F (+35°C)
Operating humidity: between 30% and 90%
Never put any heat-producing device under the projector to pre-
vent the projector from being overheated.
Do not install the projector at a place that is unstable or subject to
vibration.
Do not install the projector near any equipment that produces a
strong magnetic field. Also refrain from installing the projector near
any cable carrying a large amount of current.
Place the projector on a solid, vibration-free surface. Otherwise it
may fall, causing serious injury or damage.
Do not stand the projector on its end. It may fall, causing serious
injury or damage.
Slanting the projector more than ±10° (right and left) or ±15° (front
and rear) may cause trouble or explosion of the lamp.
Do not place the projector near air-conditioning unit, heater, or
humidifier to avoid hot or moist air to the exhaust and ventilation
hole of the projector.
Be sure to use this projector at an altitude of less than 1500
meters.
When removing the lamp from the ceiling-mounted
projector
Be sure to use the lamp replacement attachment designed specifically
for this projector when replacing the lamp with a new one. Lamp frag-
ments may fall from the inside if the lamp were broken.
COMPLIANCE NOTICE OF FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gen-
erates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm-
ful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced Radio / TV technician for help.
Changes or modifications not expressly approved by Mitsubishi could void the user’s authority to operate this equipment.
COMPLIANCE NOTICE OF INDUSTRY CANADA
This Class B digital apparatus complies with Canadian ICES-003.
EN-6
Overview
1FOCUS ring
2ZOOM ring
3 Control panel
4 Air inlet grille
5 Remote control sensor (Front)
6 Air outlet grille
7 Terminal board
8 Speaker
9 Adjustment feet
10 Lock bar
11 Lamp cover
Caution:
Do not replace the lamp immediately after using the pro-
jector because the lamp would be extremely hot and it
may cause burns.
Control panel
1 POWER button (ON/STANDBY)
The status is changed between ON and STANDBY.
2 POWER indicator
3 MENU button
4 STATUS indicator
5 KEYSTONE/ENTER button
6 AUTO POSITION / S button
7 COMPUTER / W button
8 T button
9 VIDEO/ X button
Important:
While the menu or the screen for the keystone adjust-
ment or password entry is being displayed, the COM-
PUTER, VIDEO, and AUTO POSITION buttons
function as the W, X, and S buttons respectively.
While the menu is on the screen, the KEYSTONE but-
ton functions as the ENTER button.
Terminal board
1Power jack
2 COMPUTER IN terminal (1, 2) (Mini D-SUB 15-pin)
3 MONITOR OUT terminal (Mini D-SUB 15-pin)
4 Remote control sensor (Rear)
5 AUDIO IN-1 terminal (Mini jack)
6 AUDIO IN-2 terminal (Mini jack)
7 AUDIO OUT terminal (Mini jack)
8 S-VIDEO terminal
9 VIDEO terminal
10 SERIAL (RS-232C) terminal (Mini DIN)
11 Kensington Lock
12 LAN terminal (RJ-45)
13 AUDIO IN-3 terminals (L/R)
14 HDMI terminal (HDMI 19-pin)
Kensington Lock
This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System.
Refer to the information that came with the Kensington System for instructions on how to use it to secure the projector. Please contact Kensington
Technology Group below.
Kensington Technology Group
2855 Campus Drive
San Mateo, CA 94403, U.S.A.
Phone: +1- (650)572-2700 Fax: +1- (650)572-9675
11
985
1 23 4
10
7
6
6
4
2
8 9
5 3 17
7 513
8
214 3 10 12 4
61
9 11
EN-7
ENGLISH
Overview (continued)
Bottom side
1 Adjustment feet
Remote control
1ON button
2 MAGNIFY button
3 VOLUME UP, DOWN buttons
4 KEYSTONE button
5 MENU button
Two types of MENU display are equipped. QUICK
MENU appears on the screen when pressing MENU
button. In addition, DETAIL MENU appears when
selecting DETAIL MENU in this MENU and pressing
ENTER button.
6ENTER button
7 AV (Audio/Video) MUTE button
8 STANDBY button
9 ASPECT button
10 AUTO POSITION button
11 Direction buttons
12 FREEZE button
13 VIDEO, S-VIDEO buttons
14 COMPUTER (1, 2) buttons
15 HDMI button
The UP and DOWN buttons are used in the KEY-
STONE adjustment in addition to the volume control.
ON
ASPECTMAGNIFY
KEYSTONE
VOL PAGE
UP
DOWN
MENU
FREEZE
AUTO
POSITION
AV
MUTE
ENTER
1
2
COMPUTER
VIDEO
VIEWER
UNPLUG
S-VIDEO
WIRELESS DVI HDMI
STANDBY
1
2
3
4
5
6
7
8
9
13
14
10
11
12
15
This model does not
have these functions.
This model does not
have these functions.
EN-8
Remote control
Battery installation
Use two (AA, R6) size batteries.
1. Remove the back cover of the remote control by pushing the battery compartment door in the direction of the arrow.
2. Load the batteries making sure that they are positioned correctly (+ to +, and - to -).
Load the batteries from - spring side, and make sure to set them tightly.
3. Replace the back cover.
Caution:
Use of a battery of wrong type may cause explosion.
Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.
Dispose of used batteries according to your local regulations.
Batteries may explode if misused. Do not recharge, disassemble, or dispose of in fire.
Be sure to handle the battery according to the instructions.
Load the battery with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.
Keep batteries out of reach of children and pets.
Remove the battery, if the remote control is not used for a long time.
Do not combine a new battery with an old one.
If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them
with water and then consult your doctor.
Operation range (of the remote control)
The maximum operation distance of the remote control is about 10 m (or about 32 feet) when the remote control is pointed at the remote control
sensor of the projector. When the remote control is pointed to the screen, the distance from the remote control to the projector via the screen should
be 5 m or less. However, the operation distance varies depending on the type of the screen used.
Important:
Do not expose the remote control sensor to direct sunlight or fluorescent. Keep a distance at least 2 m (6.5 feet) between the remote control sen-
sor and the fluorescent light to ensure correct operation of the remote control.
Inverted fluorescent light, if located near the projector, may interfere the remote control.
When you use the remote control too close to the remote control sensor, the remote control may not work correctly.
Reception angle (horizontal) Reception angle (vertical), ceiling mount
Reception angle (vertical)
EN-9
ENGLISH
Installation
Layout of the projector
Image size varies depending on the distance between the screen and the projector.
Front projection
The above figures are approximate and may be slightly different from the actual measurements.
Front projection, ceiling mounting
For ceiling mounting, you need the ceiling mount kit designed for this
projector. Ask a specialist for installation.
For details, consult your dealer.
The warranty on this projector does not cover any damage caused
by use of any non-recommended ceiling mount kit or installation of
the ceiling mount kit in an improper location
.
When using the projector mounted on the ceiling, set IMAGE
REVERSE in the INSTALLATION menu to MIRROR INVERT. See
page 22.
When the projector is mounted on the ceiling, images may appear
darker than those projected in the case of tabletop mounting. This
isn’t a product malfunction.
Ceiling Mount Installation
If you wish to install the projector using a ceiling mount, please use
the screw holes as the illustration shows.
Important:
Screws are not included. Please obtain the appropriate screws for
your type of ceiling. (M4 diameter)
It is recommended that you keep a reasonable space between the
bracket and the projector to allow for proper heat distribution.
Rear projection
Ask a specialist for installation. For details, consult your dealer.
For rear projection, set IMAGE REVERSE in the INSTALLATION
menu to MIRROR. See page 22.
Caution:
Placing the projector directly on a carpet impairs ventilation by the
fans, causing damage or failure. Put a hard board under the pro-
jector to facilitate ventilation.
Place the projector at least 50 cm (or 20 inch) away from the wall
to prevent the air inlet grille and the air outlet grilles that emit hot
air from being blocked.
Do not use the projector in the following locations and manners,
which may cause fire or electric shock.
In a dusty or humid place.
In a sideways or upside-down position.
Near a heater.
In an oily, smoky, or damp place such as a kitchen.
In direct sunlight.
Where the temperature rises high, such as in a closed car.
Where the temperature is lower than +41°F (or +5°C) or higher
than +95°F (or +35°C ).
Important:
Do not apply force to the lens, because the lens may be damaged.
Be sure to use this projector at an altitude of less than 1500
meters.
Screen Distance from the screen : L
Hd
Diagonal size Width : SW Height : SH Shortest (WIDE) Longest (TELE)
inch cm inch cm inch cm inch m inch m inch cm
4010232812461 45 1.1 67 1.7 3.6 9
60 152 48 122 36 91 68 1.7 102 2.6 5.4 14
80 203 64 163 48 122 91 2.3 137 3.5 7.2 18
100 254 80 203 60 152 115 2.9 171 4.3 9.0 23
150 381 120 305 90 229 173 4.4 258 6.5 13.5 34
200 508 160 406 120 305 231 5.9 344 8.7 18.0 46
250 635 200 508 150 381 289 7.3 431 10.9 22.5 57
300 762 240 610 180 457 348 8.8 - - 27.0 69
SH
Hd
L
SW
L : Between the screen and the front edge of the projector
Hd : Height of the projected image
EN-10
Basic connections
This projector can be connected with various devices such as a VCR, video camera, videodisc player, and personal computer that have analog RGB
output connectors.
Important:
Make sure that the connected device is turned off before starting connection.
Plug in the power cords of the projector and the connected devices firmly. When unplugging, hold and pull the plug. Do not pull the cord.
When the projector and the connected devices are located too close to each other, the projected image may be affected by their interference.
See the owner’s guide of each device for details about its connections.
Projector + AV device
Important:
Match the colors of the video and audio plugs on the Audio cable with those of the terminals.
Speaker output is mono.
Projector + DVD player or HDTV decoder
Some DVD players have an output connector for 3-line fitting (Y, CB, CR). When connecting such DVD player with this projector, use the
COMPUTER IN terminal.
Important:
The terminal’s names Y, PB, and PR are given as examples of when a HDTV decoder is connected.
The terminal’s names vary depending on the connected devices.
Use a Mini D-SUB 15-pin - BNC conversion cable for connection.
Image may not be projected correctly with some DVD players.
When connecting a HDTV decoder having RGB output terminals, set COMPUTER INPUT to RGB in the SIGNAL menu.
S-VIDEO IN
(option)
AUDIO IN-3L
(option)
to audio output (L)
to audio output (R)
to S-video output
VCR, etc.
to Video output
VIDEO IN
(option)
AUDIO IN-3R
BR
DVD player or HDTV decoder
Audio cable (option)
to audio output
BNC - RCA connector (option)
No connection
COMPUTER IN
Mini D-SUB 15-pin - BNC conversion
cable (option)
EN-11
ENGLISH
Basic connections (continued)
Connection (for video equipment having an HDMI terminal)
Important:
Use a commercially available HDMI (with HDMI logo) cable.
You don’t have to connect any cable for audio input. You can input video and audio using an HDMI cable only.
When HDMI audio isn’t output, it may be output by turning off the power of the video equipment with the projector and the video equipment con-
nected to each other and then turning back on the power.
Some cables may not be connected correctly depending on the size and shape of their connectors.
Equipment having an
HDMI terminal
to HDMI terminal
HDMI (with HDMI logo) cable (option)
HDMI IN
EN-12
Basic connections (continued)
Projector + Computer
For computer with Mini D-SUB
For analog connection:
1. Connect one end of the supplied RGB cable to the COMPUTER IN terminal (1, 2) of the projector.
2. Connect the other end of the RGB cable to the monitor port of the computer.
For monitor connection:
Connect the RGB cable from the monitor to the MONITOR OUT terminal of the projector.
Images may not be displayed correctly depending on the type of the input signal. See the instruction manual of the monitor.
Signals are coming from the COMPUTER IN terminal (1 or 2) of the projector.
MONITOR OUT is not output during the STANDBY state.
When signals are coming from both COMPUTER IN terminals (1, 2), images are projected from the terminal (1 or 2) currently or last selected in
the projector's menu.
Important:
When you use a longer RGB cable instead of the provided cable, the image may not be projected correctly.
Some computers require additional connectors or analog RGB output adapters to be connected with this projector. Contact your dealer for fur-
ther information.
This projector uses stereo mini jack for its audio input. Check the type of the audio output terminal of the connected computer and prepare a
proper cable for connection. Some computers don’t have the audio output terminal.
Speaker output is mono.
When the audio cable is connected to the AUDIO OUT terminal, the speaker output is muted.
For Macintosh
If your Macintosh has no video port, a monitor output adapter is required. Contact your dealer for further information.
Some Macintoshes require a MAC adapter for the RGB cable for connection with this projector. Contact your dealer for further information.
About DDC
The COMPUTER/COMPONENT VIDEO IN-1 terminal of this projector complies with the DDC 1/2B standard. When a computer supporting this
standard is connected to this terminal, the computer will automatically load the information from this projector and prepare for output of appropriate
images.
After connecting a computer supporting this standard to this terminal, plug the power cord of the projector in the wall outlet first, and then boot up
the computer.
COMPUTER IN
RGB cable for PC
AUDIO
OUT
Audio cable (option)
MONITOR OUT
Necessary when outputting to both
a PC monitor and the projector.
PC audio cable (option)
AUDIO IN-1
or IN-2
to PC audio output
Computer
to monitor port
RGB cable for PC (option)
EN-13
ENGLISH
Preparation
Preparation for projection
1. Attach the provided power cord to the projector.
2. Plug the power cord in the wall outlet.
3. Remove the lens cap.
Warning:
Do not look into the lens directly when the projector is on.
The lens cap is for protecting the lens. If you leave the lens cap on
the lens with the projector turned on, it may be deformed because
of heat build-up. Remove the lens cap when you turn on the pro-
jector.
One of power cords for the U.S., Europe and U.K. is provided
appropriately.
This projector uses the power plug of three-pin grounding type. Do
not remove the grounding pin from the power plug. If the power
plug doesn’t fit your wall outlet, ask an electrician to change the
wall outlet.
In case that the power cord for the U.S. is provided with this pro-
jector, never connect this cord to any outlet or power supply using
other voltages or frequencies than rated. If you want to use a
power supply using other voltage than rated, prepare an appropri-
ate power cord separately.
Use 100-240 V AC 50/60 Hz to prevent fire or electric shock.
Do not place any objects on the power cord or do not place the
projector near heat sources to prevent damage to the power cord.
If the power cord should be damaged, contact your dealer for
replacement because it may cause fire or electric shock.
Do not modify or alter the power cord. If the power cord is modified
or altered, it may cause fire or electric shock.
Caution:
Plug in the power cord firmly. When unplugging, hold and pull the
power plug, not the power cord.
Do not plug in or out the power cord with your hand wet. It may
cause electric shock.
Adjustment of the projection angle
For the best projection, project images on a flat screen installed at 90
degrees to the floor. If necessary, tilt the projector using the two
adjustment feet on the bottom of the projector.
Using the adjustment feet (front)
1. Tilt up the projector to the appropriate angle.
2. Rotate the adjustment feet (front) for fine adjustment.
Important:
Install the screen on a flat wall at 90 degrees to the floor.
Slanting the projector more than ±10° (right and left) or ±15° (front
and rear) may cause trouble or explosion of the lamp. You can tilt
the projector up to 8 degrees using the adjustment feet only.
Images may not be projected in a shape of a regular rectangle or
with its aspect ratio 4:3, depending on the installation conditions of
the projector and the screen.
When AUTO KEYSTONE in the INSTALLATION menu is set to
ON, this projector automatically corrects vertical keystone distor-
tion. For fine adjustment, press the KEYSTONE button on the pro-
jector or the remote control to display KEYSTONE, and adjust the
image by pressing the S, T button (or VOLUME S, T button on
the remote control).
In the following cases:
The automatic keystone adjustment may not be carried out cor-
rectly because of the ambient temperature and the installation
conditions of the projector and the screen. In such cases, correct
the keystone manually.
When the projector is projecting images where acceleration is
present, such as in a vehicle and aircraft, the automatic keystone
adjustment may not function correctly. In such a case, set AUTO
KEYSTONE in the INSTALLATION menu to OFF and correct the
keystone manually.
You can correct the vertical keystones. However, their adjustment
ranges are limited in such correction.
Important:
When the keystone adjustment is carried out, the adjustment
value is indicated. Note that this value doesn’t mean a projection
angle.
The allowable range of the adjustment value in the keystone
adjustment varies depending on the installation condition, Input
signal and aspect settings in MENU.
When the keystone adjustment takes effect, the resolution
decreases. In addition, stripes may appear or straight lines may
bend in images with complicated patterns. They are not due to
product malfunctions.
Noise may appear on the screen during the keystone adjustment
because of the type of the video signal being projected and the
setting values of the keystone adjustment. In such cases, set the
keystone adjustment values in the range where the image is dis-
played without noise.
When the keystone adjustment is carried out, the image may not
be displayed correctly because of the type of input signal.
Press the T
button.
Press the S
button.
EN-14
Basic operation
Power-on
1. Turn on the device connected to the projector first.
2. Plug the power cord in the wall outlet.
The POWER indicator lights up.
If the power cord is unplugged from the wall outlet before the
projector is cooled down completely after use, the fans may
start rotating when the power cord is plugged in next time
and the POWER button may not function. In this case, wait
for the fans to stop and press the POWER button to light the
indicator.
3. Press the POWER button on the control panel or the ON button
on the remote control.
It may take about one minute for the lamp to light up.
The lamp occasionally fails to light up. Wait a few minutes
and try to light the lamp again.
After the POWER button is pressed, the image may flicker
before the lamp becomes stable. This is not a product mal-
function.
Regardless of the setting of LAMP MODE in the INSTALLA-
TION menu, the STANDARD lamp mode is activated by
default whenever the projector is turned on. The LAMP
MODE is set to either STANDARD or LOW depending on the
setting last selected, and you cannot switch the LAMP
MODE in about one minute after the lamp is on.
Important:
If the lamp exceptionally turned off due to the power interruption or
voltage drop, it can happen that the lamp does not turn on even if
you switch again the power supply on. In that case, please pull the
electric cord out of the consent and put it again in the consent
about 10 minutes later.
Do not cover the lens with the lens cap while the lamp is on.
The projector starts warming up when the POWER button is
pressed. During the warm-up process, images may appear dark
and no commands are accepted.
By blinking red, the STATUS indicator indicates that the lamp
should be replaced soon. Replace the lamp when the STATUS
indicator blinks red. (See page 36 and 39.)
Images may not be projected with good quality in an extremely hot
or cold environment. (This is not a product malfunction.)
In order to ensure the safety in case of trouble with the projector,
use an electrical outlet having an earth leakage breaker to supply
the power to the projector. If you do not have such outlet, ask your
dealer to install it.
4. Adjust the focus by turning the focus ring.
5. Choose your desired external input source using the COM-
PUTER, VIDEO or HDMI button.
The input source is switched between COMPUTER1,
COMPUTER2, and HDMI at every press of the COMPUTER
button on the control panel.
The input source is switched between VIDEO and S-VIDEO
at every press of the VIDEO button on the control panel.
When pressing COMPUTER (1 or 2), HDMI, VIDEO, or S-
VIDEO button on the remote control, the input source
switches directly as the button pressed.
The projector automatically selects the appropriate signal
format. The selected signal format is displayed on the
screen.
The COMPUTER, VIDEO and HDMI buttons don’t function
while the menu is being displayed.
When COMPUTER is chosen as the source, images sup-
plied from the computer may flicker. Press the W or X button
on the remote control to reduce flicker, if it occurs.
To avoid permanently imprinting a fixed image onto your pro-
jector, please do not display the same stationary images for
long period.
6. Adjust the image size by turning the zoom ring.
If necessary, adjust the focus and zoom again.
When fine streaks are seen on projected images
This is due to interference with the screen surface and is not a mal-
function. Replace the screen or displace the focus a little.
STANDBYON
ASPECTMAGNIFY
KEYSTONE
VO L PAG E
UP
DOWN
MENU
FREEZE
AU TO
POSITION
AV
MUTE
ENTER
1
2
COMPUTER
VIDEO
VIEWER
UNPLUG
S
-
VIDEO
WIRELESS HDMIDVI
4 FOCUS
6 ZOOM
53, 1, 2
5
1, 23
Indicator
Condition
STATUS POWER
Stand-by - Red
When the lamp is on. Green Green
EN-15
ENGLISH
Basic operation (continued)
Power-off
Use the following procedure to turn off the projector.
The lamp may deteriorate if the projector is powered off and on
repeatedly within 30 minutes after the lamp is lighted.
1. Press the POWER button on the control panel or the STANDBY
button on the remote control.
The message "POWER OFF? YES : PRESS AGAIN"
appears on the screen.
To cancel, press any button except the POWER button.
(Some buttons on the remote control don’t function for can-
cel.)
2. Press the POWER button on the control panel or the STANDBY
button on the remote control within 10 seconds again.
The lamp will go out and the STATUS indicator will start
blinking.
Though the lamp goes out at this second press of the
POWER button (or STANDBY button), the air outlet fans con-
tinue operating for one minute to cool down the lamp. The
STATUS indicator will stop blinking.
After stopping the air outlet fans, if the temperature inside the
set is still high, the temperature sensor detects it and then
the air outlet fans may start again.
3. Unplug the power cord.
The POWER indicator will go out.
If the power cord should be unplugged accidentally while
either the air inlet fan or the air outlet fans are operating or
the lamp is on, allow the projector to cool down for 10 min-
utes with the power off. To light the lamp again, press the
POWER button (or ON button). If the lamp doesn’t light up
immediately, repeat pressing the POWER button (or ON but-
ton) two or three times. If it should still fail to light up, replace
the lamp.
Notice:
When storing the projector in the carrying case, the lens should
face up.
Before carrying the projector, rotate Focus Ring and Zoom Ring to
adjust the lens to the shortest. This prevents the possible dam-
ages of the lens.
Instant Shut Down
You can turn off this projector just by unplugging the power cord with-
out pressing the POWER button.
Don't shut down the projector while the STATUS indicator is blink-
ing after the lamp lights up because the lamp's life may be short-
ened.
Don't turn the projector back on right after shutting it down
because the lamp's life may be shortened. (Wait about 10 minutes
before turning the projector back on.)
Before shutting down the projector, be sure to close the menu
screen. If you shut down the projector without closing the menu,
the setting data of the menu may not be saved.
If you shut down the projector while controlling the projector using
the network function, the application software such as Projector-
View may fail. For details, see "User Manual of LAN Control Utility"
contained in the CD-ROM.
AUTO POSITION button
When the image isn’t projected in the right position with COMPUTER
selected as the input source, follow the procedure below.
1. Project a bright image such as the "Recycle Bin" window on the
full screen.
2. If the screen saver is running, turn it off.
3. Press the AUTO POSITION button.
If the image is still not in the right position, adjust the image
position using the SIGNAL menu. See page 24.
Volume from the speaker
Press the VOLUME S or T button to change the volume
from the speaker.
The volume control bar will appear on the screen.
The volume control bar will disappear about 10 seconds after the
VOLUME button is released.
The VOLUME buttons don’t function while the menu selection bar
or the menu is being displayed.
When a high-level audio signal, such as a DVD audio signal, is
supplied to the AUDIO IN terminal, the output from the speaker
may be distorted.
AV mute
The video and audio signals are temporarily muted when the AV
MUTE button is pressed. To cancel muting, press the AV MUTE button
again.
Setting the aspect ratio
You can change the aspect ratio of the input video signal (or the ratio
of width to height of the image). Change the setting according to the
type of the input video signal.
How to change the settings:
With the remote control:
1. Press the ASPECT button.
Every time the ASPECT button is pressed, the aspect mode
changes from NORMAL to 16:9, to FULL, and back to NOR-
MAL.
With the FEATURE menu:
(See page 21 for menu setting.)
1. Display the FEATURE menu.
2. Select ASPECT by pressing the S or T button.
3. Select your desired aspect ratio by pressing the W or X button.
When 16:9 is selected.
4. Press the ENTER button.
5. Select your desired position (CENTER, UPPER or LOWER) by
pressing the W or X button.
To cancel the menu:
6. Press the MENU button.
Important:
When a 16:9 image is kept displayed for a long time before dis-
playing 4:3 image, the afterimages of the black bars may appear
on the 4:3 image screen. Consult your dealer in this case.
Caution:
After using the projector, wait one minute for the air outlet fans to
stop in normal use. Then unplug the power cord from the wall out-
let.
The lamp can’t be lit again for one minute after turned off for safety
purpose. It will take another one minute for the STATUS indicator
to go out. If you want to turn on the projector again, wait until the
indicator goes out, and then press the POWER button.
The air outlet fans rotate faster as the temperature around the pro-
jector rises.
When the temperature around the projector rises high, the sign
"TEMPERATURE!!" blinks red on the screen. If the temperature
stays high, the lamp will go out automatically.
Important:
Do not display a still picture for a long time because the afterim-
ages may persist on the screen.
VOLUME 10
NORMAL
ASPECT
FEATURE
opt.
EN-16
Basic operation (continued)
Wall Screen
This function is to reproduce natural color tones when images are pro-
jected directly onto a screen or wall surface. You can select from
BEIGE, LIGHT BLUE, LIGHT GREEN, PINK, BLACK BOARD, WHITE
BOARD, and OFF, to match the color of the screen or wall to be used
for projection.
1. Display the INSTALLATION menu. (See page 22 for more details.)
2. Press the S or T button to select WALL SCREEN.
3. Press the W or X button to select the color closest to that of the
screen on which images are projected.
When the GAMMA mode setting is changed, images may not
be displayed correctly.
When OFF or BLACK BOARD/WHITE BOARD is selected,
the density cannot be adjusted.
When WHITE BOARD is selected, BrilliantColor
TM
in the
Color Enhancer menu of the Image menu cannot be used.
Additionally, Theater in the Color Enhancer menu of the
Image menu has no effect and is automatically canceled
when WHITE BOARD is selected.
4. Press the ENTER button.
5. Press the W or X button to adjust the density of the selected
color.
Watching 3D Content
You can enjoy 3D Content with this projector.
In order to watch 3D Content, you need to have the following items:
A Field-sequential 3D video contents
B DLP
TM
Link
TM
active electronic shutter glasses
(Field-sequential : The system which displays alternately the image
for the left eye and the right eye.)
.
Play the field-sequential 3D video contents on a computer or DVD
player, and then, connect the cable with the projector.
Go to the IMAGE menu, and click the ADVANCED MENU, then, set
the 3D option to ON. (See page 21.)
Put on the electronic shutter glasses to watch the contents.
If the contents are not projected correctly, go to the IMAGE menu, and
switch the order of the image setting the 3D SYNC. option in the
ADVANCED MENU.
Note:
Watch the contents in front of the screen, not at big angle. If you
are viewing the screen at big angle, you may not be able to view
3D contents correctly.
If you are not viewing 3D contents correctly, check to see if the
electronic shutter glasses are powered on or adequately charged.
See the instruction manual of the electronic shutter glasses for
more information.
With the 3D option set to ON, contents displayed on the projector
appear darker. It is normal and does not mean the projector is
malfunctioning.
The following features cannot be used when viewing 3D contents
on the projector:
KEYSTONE adjustment
Magnify
Color Enhancer switching
CINEMA MODE switching
WXGA mode switching
VERT. SYNC. switching
Image Capture
OVER SCAN function
SHUTTER function
It may occur that the image may not be enough 3D image because
setting such as fluorescent lighting may occur loss of synchronism
of glasses.
3D image may not appear on the screen depending on the PC
performance such as graphics board, memory, or CPU.
The signals in the below table can be displayed with viewing 3D
Contents on the projector. If a different signal is inputted, the pro-
jector shows no 3D Contents even with the 3D option set to ON in
the ADVANCED MENU of the IMAGE menu.
If DVD is run by 480p signals, 3D image may not be displayed cor-
rectly depending on the DVD player.
When 3D image is projected on the screen in 120Hz or using cer-
tain type of playback software of PC, the image may not appear on
the screen.
LAMP MODE
ST
ANDARD
WALL SCREEN
BEIGE
opt.
INSTALLATION
LIGHT BLUE 1
RL
LRLRLRLR
LRLRLRLR
LRLRLRLR
LRLRLRLR
LRLRLRLR
LRLRLRLR
R
L
L
L
R
R
R
L
RLRL
3D image Format
Page Flipping
(Field Sequential)
Side by Side Top & Bottom Checkerboard
Supported Not supported Not supported Not supported
Sensor
DLP Link active electronic
shutter glasses
DLP Projector
The shutter timing of
shuttered glasses is
controlled by being
synchronized with switching
of right and left 3D image
which is detected by the
sensor of glasses.
Signal
resolution
(H x V)
horizontal
frequency (kHz)
vertical
frequency (Hz)
TV60, 480i (525i) - 15.73 59.94
480p (525p) - 31.47 59.94
VGA60 640 x 480 31.47 59.94
XGA60 1024 x 768 48.36 60.00
XGA120 1024 x 768 97.55 119.99
EN-17
ENGLISH
Basic operation (continued)
Caution:
Notes on danger to public health during watching 3D image
Stop watching 3D image if you feel fatigue or discomfort.
Stop watching 3D image if you see doubly-blurred image or you
cannot view the image stereoscopically.
The following people need to refrain from use as with 2D image.
a photosensitive patient
a patient with heart disease
a person in poor physical condition
a sleepy person
a very tired person
a drunk person
children
When viewing 3D images, view them in a position where both eyes
are level with the horizontal direction of the projector.
If you have abnormal feelings such as fatigue or discomfort when
viewing 3D images, stop viewing them and take a rest. If fatigue or
discomfort persists after the rest, stop viewing.
When viewing 3D images, take a rest after around 30 - 60 minutes
even if you do not have abnormal feelings such as fatigue or dis-
comfort.
When children view 3D images, make sure that they are under
observation by guardians, and pay attention to the changes of
their physical conditions or if they have eye fatigue.
When having difficulty or when feeling discomfort in the scenes
with quick motions, stop staring the screen and look away from it.
When viewing contents with movements such as rotation, or hori-
zontal or vertical oscillation, you may feel as if you are actually
moving. If such a feeling results in discomfort, look away from the
screen.
When connecting to a laptop computer:
When this projector is connected to a laptop computer, there may be
times when images may not be projected. When it occurs, set the
computer so that it can output signals externally. The procedure varies
across computers in use. See the instruction manual of your com-
puter.
EN-18
Menu operation
As one of the two types of MENU display, following QUICK MENU appears on the screen when pressing MENU button on the remote control. In
addition, DETAIL MENU (See page 20) appears when selecting DETAIL MENU in this MENU and pressing ENTER button.
Comparing QUICK MENU with DETAIL MENU, if the contents in those two menus are same each other, the functions in those two menus are
same as well.
To close QUICK MENU or DETAIL MENU, press MENU button when MENU is displayed.
QUICK MENU
* Menus are not displayed when no signal is supplied to the projector.
QUICK MENU Basic operation
Several settings can be adjusted using the menu.
Example : Contrast setting
1. Press the MENU button.
2. Press the ENTER button (or T button).
3. Press the S or T button to select CONTRAST.
4. Press the W or X button to adjust the contrast.
5. Exit the menu by pressing the MENU button several times.
Important:
When the button doesn’t function, unplug the power cord from the
wall outlet. Wait about 10 minutes, plug the power cord in, and try
again.
After selecting the items marked with , press the ENTER but-
ton.
QUICK MENU COLOR ENHANCER
CONTRAST
BRIGHTNESS
COLOR TEMP.
AUTO
THEATER
USER
PRESENTATION
STANDARD
±30
STANDARD
SHARPNESS *1
±5
LAMP MODE
ASPECT
USER MENU
SELECT USER MENU
STANDARD, LOW
COLOR
LOW
HIGH
USER
INFORMATION
SYNC. TYPE *2
LAMP TIME (LOW)
INPUT
RESOLUTION
VERTICAL FREQUENCY
HORIZONTAL FREQUENCY
±30
WALL SCREEN
TINT
CLOSED CAPTION
AUDIO INPUT
IMAGE REVERSE
MENU POSITION
CINEMA MODE
WXGA
LANGUAGE
STANDBY MODE
NORMAL, 16:9, FULL
DETAIL MENU
OK
*1 Not available with certain signals
*2 Not available when the input signal is from the VIDEO IN or S-VIDEO IN terminal.
QUICK MENU
AUTO
COLOR
ENHANCER
QUICK MENU
0
CONTRAST
+10
CONTRAST
EN-19
ENGLISH
Menu operation (continued)
Menu Options
Set the following options provided in the respective menus.
1. QUICK MENU
You cannot adjust COLOR TEMP. when WALL SCREEN is set to other than OFF.
When COLOR ENHANCER is switched, projected images may be distorted.
By default, the LAMP MODE is set to STANDARD. The LAMP MODE is set to either STANDARD or LOW depending on the setting last selected,
and you cannot switch the LAMP MODE in about one minute after the lamp is on.
2. INFORMATION menu
Menu option Setting Feature description
COLOR ENHANCER
AUTO
Automatically sets an optimal color balance based on the input signal.
Use this setting for most cases.
PRESENTATION Makes projected images bright and crisp.
STANDARD Makes projected images look natural.
THEATER Makes projected images soft and smooth. Best suited for movies.
USER Reflected by the value set in IMAGE menu. (See page 26.)
CONTRAST ±30 Adjusts the contrast of projected images. (See page 26.)
BRIGHTNESS ±30 Adjusts the brightness of projected images. (See page 26.)
COLOR TEMP. 4 options
Adjusts the color temperature. You cannot select this setting when
WALL SCREEN in the INSTALLATION menu is set to a setting other
than OFF. (See page 26.)
SHARPNESS ±5 Adjusts the sharpness of projected images. (See page 26.)
LAMP MODE
STANDARD Select this setting when you want to view images in a well-lit room.
LOW
Select this setting when you want to view images at a moderate light
intensity. The operating sound is consequently reduced, and the lamp
lifetime becomes longer.
When this mode is switched, projected images may flicker.
If this mode is frequently switched, the lamp may be deteriorated.
ASPECT
NORMAL
Automatically sets the aspect ratio in relative to the input signal. Use this
setting for most cases.
16:9
Selects a desired screen position for anamorphically squeezed or hori-
zontally compressed images stored on DVD disks.
FULL Select this setting when you want to project images in the full screen.
USER MENU Displays the menu item selected in SELECT USER MENU.
SELECT USER MENU Select the item to display in USER MENU.
DETAIL MENU Moves to DETAIL MENU.
Menu option Feature description
LAMP TIME (LOW)
This menu shows a lamp operating time (hour) calculated assuming that LAMP MODE is LOW.
When the LAMP MODE is STANDARD, this menu shows a longer lamp operating time than
the actual time. (See page 35 for the interval of lamp replacement.)
When the lamp operating time is 0 to 10 hours, "0H" is displayed. When the lamp operating
time exceeds 10 hours, the actual hours are displayed.
When the lamp operating time reaches 3750 hours, the bar turns yellow. When it reaches
4750 hours, the bar turns red.
(The lamp lifetime is 5000 hours.)
INPUT Indicates the name of the terminal to which the currently projected video signal is being input.
RESOLUTION Indicates the resolution of the currently projected video signal.
VERTICAL FREQUENCY Indicates the vertical frequency of the currently projected video signal.
HORIZONTAL FRE-
QUENCY
Indicates the horizontal frequency of the currently projected video signal.
SYNC. TYPE Indicates the type of the sync signal for the currently projected video signal.
DETAIL MENU
SELECT
USER MENU
ASPECT
USER MENU
NORMAL
OK
COLOR
QUICK MENU
CONTRAST
BRIGHTNESS
0
0
STANDARD
STANDARD
0
COLOR TEMP.
SHARPNESS
AUTO
COLOR
ENHANCER
LAMP MODE
LAMP TIME (LOW)
INPUT
RESOLUTION
VERTICAL
FREQUENCY
HORIZONTAL
FREQUENCY
SYNC. TYPE 5wire
60.02 KHz
75.04 Hz
1024x768
COMPUTER2
0 H
RG
HV
B
INFORMATION
EN-20
Menu operation (continued)
DETAIL MENU
* Menus are not displayed when no signal is supplied to the projector.
IMAGE
INSTALLATION
FEATURE
SIGNAL
INFORMATION
COLOR ENHANCER
CONTRAST
BRIGHTNESS
COLOR TEMP.
AUTO
PRESENTATION
STANDARD
±30
±30
STANDARD
COLOR *1
TINT *1
SHARPNESS *1
ADVANCED MENU
±10
±10
±5
WALL SCREEN
LAMP MODE
STANDBY MODE
AUDIO INPUT
AUTO KEYSTONE
IMAGE REVERSE
ADVANCED MENU
STANDARD, LOW
STANDARD, LOW
AUTO, AUDIO 1, AUDIO 2, AUDIO 3, MIX *6
BLACK BOARD
WHITE BOARD
OFF
OFF, MIRROR, INVERT, MIRROR INVERT
LOW
GAMMA MODE
BrilliantColor
TM
RGB-COLOR
RGB-TINT
HIGH
CONTRAST R
CONTRAST G
CONTRAST B
BRIGHTNESS R
BRIGHTNESS G
BRIGHTNESS B
NOISE REDUCTION *1
CTI *1
INPUT LEVEL
DYNAMIC, NATURAL, DETAIL
0-10
±10
±10
±30
±30
±30
±30
±30
±30
ON, OFF
ON, OFF
±
5
CLOSED CAPTION *1
AUTO POWER ON
AUTO POWER OFF
IMAGE CAPTURE
SPLASH SCREEN
BACK COLOR
AV MUTE MODE
OFF, CC1, CC2
3D
ON, OFF
3D SYNC.
1, 2
ON, OFF
OFF, 5min, 10min, 15min, 30min, 60min
ON, OFF
BLUE, BLACK, IMAGE
BLACK, IMAGE
1-5
1-5
1-5
1-5
ASPECT
SETUP *1
LANGUAGE
RESET ALL
PA SSWORD FUNCTION
MENU POSITION
CINEMA MODE *3
VIDEO SIGNAL *5
WXGA *2
NORMAL
AUTO, OFF, 3.75%, 7.5%
DISPLAY INPUT , MENU ACCESS , SPLASH ID SCREEN
1 (upper left), 2 (lower right)
FULL
AUTO, OFF
AUTO, NTSC, PAL, SECAM, 4.43NTSC, PAL-M, PAL-N, PAL-60
OFF, AUTO, 1280 x 768, 1280 x 768RB, 1360 x 768, 1366 x 768, 1280 x 800
LOCK
*4
*4
*4
*4
CENTER, UPPER, LOWER
OVER SCAN
HOLD *2
HORIZ. POSITION
VERT. POSITION
FINE SYNC. *1 *2
TRACKING *2
COMPUTER INPUT *2
100-90%
OFF
0-999
0-999
0-31
0-2800
AUTO, RGB, YCBCR/YPBPR
NETWORK PROJECTOR NAME
NETWORK PASSWORD
NETWORK RESET
PJlink CERTIFICATION
IP CONFIG
BEGIN
END
SHUTTER (L)
SHUTTER (LS)
SHUTTER (RS)
CLAMP POSITION *2
CLAMP WIDTH *2
VERT. SYNC
LPF *1 *2
SHUTTER (U)
0-99
0-99
0-20
0-20
0-20
1-255
1-63
AUTO, OFF
ON, OFF
0-20
SYNC. TYPE *2
LAMP TIME (LOW)
INPUT
RESOLUTION
VERTICAL FREQUENCY
HORIZONTAL FREQUENCY
OK
UNLOCK OK
OK
USER OK
OK
OK
OK
*****..., SET
DHCP
IP ADDRESS
SUBNET MASK
DEFAULT GATEWAY
MAC ADDRESS
xx-xx-xx-xx-xx-xx
***.***.***.***, SET
***.***.***.***, SET
***.***.***.***, SET
ON
OK
USER
USER
OK
BEIGE
LIGHT BLUE
LIGHT GREEN
PINK
16:9
,
SVENSKA,
POLSKI
ON, OFF
±10
GO
THEATER
ON , OFF
ON , OFF
*1 Not available with certain signals
*2 Not available when the input signal is from the VIDEO IN or S-VIDEO IN terminal.
*3 Available only when the input signal is TV60, TV50, 480i, or 576i.
*4 The range that can be specified varies across input signals.
*5 Available only when the input signal is from the VIDEO IN or S-VIDEO IN terminal.
*6 AUDIO 1, AUDIO 2, AUDIO 3, and MIX
cannot be selected when the Input Source is HDMI input.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43

Mitsubishi XD590U User manual

Category
Data projectors
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI