Gigabyte GV-N26OC-896H User manual

GV-N26-896H-B/

GV-N26OC-896H-B/

GV-N26OC-896H

NVIDIA

®

GeForceT

M

GTX 260 Graphics Accelerator

User's Manual

Rev. 103

12MM-NX268B-103R

Copyright

Copyright by GIGA-BYTE TECHNOLOGY CO., LTD. ("GBT"). No part of this manual may be reproduced or transmitted

in any form without the expressed, written permission of GBT.

Trademarks

Third-party brands and names are the properties of their respective owners.

Notice

Please do not remove any labels on this graphics card. Doing so may void the warranty of this card.

Due to rapid change in technology, some of the specifications might be out of date before publication of this this manual.

The author assumes no responsibility for any errors or omissions that may appear in this document nor does the author

make a commitment to update the information contained herein.

Macrovision corporation product notice:

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property

rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other

limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

VGA Card

GV-N26-896H-B

Jun. 5, 2008

VGA Card

GV-N26-896H-B

Jun. 5, 2008

VGA Card

GV-N26OC-896H

Sept. 1, 2008

VGA Card

GV-N26OC-896H

Sept. 1, 2008

VGA Card

GV-N26OC-896H

Mar.19, 2009

VGA Card

GV-N26OC-896H

Mar.19, 2009

- 5 -

Table of Contents

1. Introduction ................................................................................................................ 6

1.1. Features ......................................................................................................................... 6

1.2. Minimum System Requirements .................................................................................... 6

2. Hardware Installation.................................................................................................. 7

2.1. Board Layout ................................................................................................................. 7

2.2. Hardware Installation.................................................................................................... 12

3. Software Installation.................................................................................................. 16

3.1. Windows® XP Driver and Utilities Installation .............................................................. 16

3.1.1. Operating System Requirements .............................................................................. 16

3.1.2. DirectX Installation........................................................................................................ 17

3.1.3. Driver Installation ......................................................................................................... 18

3.1.4. GIGABYTE Gamer HUD Lite on Driver Disk ........................................................... 20

3.1.5. Taskbar Icon................................................................................................................. 22

3.1.6. Display Properties Pages........................................................................................... 23

3.1.7. nView Properties Pages (Note) ................................................................................. 34

4. Troubleshooting Tips................................................................................................ 39

5. Appendix ................................................................................................................. 40

5.1. How to Reflash the BIOS in MS-DOS Mode.............................................................. 40

5.2. Resolutions and Color Depth Table (In Windows XP) ................................................... 41

5.3. Regulatory Statements ................................................................................................. 43

(Note) This item will show up when you connect two monitors.

- 6 -GV-N26 Series Graphics Accelerator

1. Introduction

1.1. Features

• Powered by NVIDIA

®

GeForce

TM

GTX 260 Graphics Processing Unit (GPU)

• Supports PCI Express 2.0

• Integrated with 896 MB GDDR3 memory

• Supports DirectX 10

• Supports NVIDIA

®

SLI

TM

(Scalable Link Interface) technology

(Note 1)

• Supports 2 DVI-I connectors

• Supports HDTV output (by optional adapter)

• Supports HDMI connector (by adapter, for GV-N26OC-896H-B only)

• Supports 1 D-Sub connectors (by adapter)

• Supports HDCP (High-Bandwidth Digital Content Protection) technology

1.2. Minimum System Requirements

• Hardware

- 500-watt power supply or greater with minimum 12V current rating of 36A.

(Note 2)

- Intel

®

Pentium

®

/Core

TM

2 or AMD Athlon

TM

/Phenom

TM

- 512 MB of system memory; 2 GB or more for best performance

- Optical drive for software installation (CD-ROM or DVD-ROM drive)

• Operating System

- Windows

®

Vista

- Windows

®

XP with Service Pack 2 (SP2)

- Windows

®

XP Professional x64 Edition

• SLI

TM

Configuration

If you are planning on using this graphics card as part of an SLI system, the following

are required:

- An SLI certified motherboard with two/three PCIe x16 slots and correct chipset driver

- Two GV-N26-896H-B/GV-N26OC-896H-B/GV-N26OC-896H for SLI configuration;

Three GV-N26-896H-B/GV-N26OC-896H-B/GV-N26OC-896H for 3-way SLI

configuration

- A power supply with 900-watt or above is recommended

- An SLI bridge connector or 3-way SLI bridge connector

(Note 1) SLI technology requires a PCI Express motherboard with two/three x16 physical connectors.

Graphics cards working in an SLI configuration must be with the same model name (e.g.

GV-N26-896H-B/GV-N26OC-896H-B/GV-N26OC-896H) and from the same vendor (e.g. GIGABYTE

TECHNOLOGY).

(Note 2) The minimum system power requirement recommended here is based on a PC configured

with an Intel Core 2 Extreme processor (QX6700).

- 7 - Hardware Installation

SLI Connector

2. Hardware Installation

2.1. Board Layout

TV-Out

DVI-I Connector 1

DVI-I Connector 2

1. GV-N26-896H-B

TV-Out

DVI-I

Connector 1

DVI-I

Connector 2

Analog LCD Monitor Analog Monitor

or

DVI-I to D-Sub

Adapter

HDTV

NTSC / PAL TV Projector

or

Pr

Pb/AV Output

S-Video Output

Digital LCD Monitor

DVI Output

D-Sub

Output

Y

DVI-I to HDMI Adapter (optional)

HDMI TV

- 8 -GV-N26 Series Graphics Accelerator

SLI Connector

TV-Out

DVI-I

Connector 1

DVI-I

Connector 2

Analog LCD Monitor Analog Monitor

or

DVI-I to D-Sub

Adapter

Digital LCD Monitor

DVI Output

DVI-I to HDMI Adapter

D-Sub

Output

HDMI TV

TV-Out

DVI-I Connector 1

DVI-I Connector 2

2. GV-N26OC-896H-B

HDTV

NTSC / PAL TV Projector

or

Pr

Pb/AV Output

S-Video Output

Y

(optional)

- 9 - Hardware Installation

SLI Connector

TV-Out

DVI-I Connector 1

DVI-I Connector 2

3. GV-N26OC-896H

TV-Out

DVI-I

Connector 1

DVI-I

Connector 2

Analog LCD Monitor Analog Monitor

or

DVI-I to D-Sub

Adapter

Digital LCD Monitor

DVI Output

DVI-I to HDMI Adapter

D-Sub

Output

HDMI TV

HDTV

NTSC / PAL TV Projector

or

Pr

Pb/AV Output

S-Video Output

Y

(optional)

- 10 -GV-N26 Series Graphics Accelerator

The GV-N26-896H-B/GV-N26OC-896H-B/GV-N26OC-896H graphics card is a performance optimized

high-end card. Power is taken from the PCI Express host bus as well as the two 6-pin PCI Express

power connectors.

Without auxiliary power provided to the GV-N26-896H-B/GV-N26OC-896H-B/GV-H26OC-896H- graph-

ics card, an LED on the bracket goes red and the graphics card will not boot. In addition, the connector

that is not adequately powered will turn red.

The table below outlines the different possible scenarios as well as the resulting behaviors.

6-pin PCIe Power 6-pin PCIe Power

Result

Connector (upper) Connector (lower)

Connected Connected Full Power

Not Connected Connected LED light is red- graphics card will not boot

Connected Not Connected LED light is red- graphics card will not boot

Not Connected Not Connected LED light is red- graphics card will not boot

If you want to use the included 6-pin power adapters, make sure at least 12V/15A current is

supplied to each 4-pin power connector on the adapters. Failure to do so may jeopardize the

stability of the graphics card.

Incorrect Connection

(The two 4-pin power connectors on

the adapter are connected to the same

system power supply cable.)

Correct Connection

(The two 4-pin power connectors on the

adapter are connected to two independent

system power supply cables.)

Requires at least 12V current

rating of 15A

6-pin Power

Adapter

Requires at least 12V current

rating of 15A

Configuration with External PCIe Connectors:

- 11 - Hardware Installation

Expansion cards contain very delicate Integrated Circuit (IC) chips. To

protect them against damage from static electricity, you should follow some

precautions whenever you work on your computer.

1. Turn off your computer and unplug power supply.

2. Use a grounded wrist strap before handling computer components. If you do not

have one, touch both of your hands to a safely grounded object or to a metal object,

such as the power supply case.

3. Place components on a grounded antistatic pad or on the bag that came with the

components whenever the components are separated from the system.

The card contains sensitive electric components, which can be easily damaged by static

electricity, so the card should be left in its original packing until it is installed.

Unpacking and installation should be done on a grounded anti-static mat. The operator

should be wearing an anti-static wristband, grounded at the same point as the anti-static

mat.

Inspect the card carton for obvious damage. Shipping and handling may cause damage

to your card. Be sure there are no shipping and handling damages on the card before

proceeding.

DO NOT APPLY POWER TO YOUR SYSTEM IF THE GRAPHICS CARD IS

DAMAGED.

In order to ensure that your graphics card can work correctly, please use

official GIGABYTE BIOS only. Using non-official GIGABYTE BIOS might

cause problem(s) on the graphics card.

- 12 -GV-N26 Series Graphics Accelerator

2.2. Hardware Installation

Now that you have prepared your computer, you are ready to install your graphics card.

Step 1.

Locate the PCI Express x16 slot. If necessary, remove the

metal cover from this slot; then align your graphics card with

the PCI Express x16 slot, and press it in firmly until the card is

fully seated.

Make sure that the gold edge connector of the graphics card is securely

inserted.

Step 2.

Replace the screw to fasten the card in place, and replace the

computer cover.

After installation, remember to connect the power cable to your graphics card, or the system

will not boot (refer to page 8 to see the details). Do not touch the card when it's operating to

prevent system instability.

Step 3.

This graphics card provides two DVI-I digital connectors. You

can connect a monitor that supports DVI-I function or use the

DVI-I to D-Sub adapter to connect a 15-pin D-Sub monitor. Or

use the DVI-I to HDMI adapter to connect an HDMI monitor.

To TV / VCR To Flat Panel Display

Connect a flat panel

Connect a D-Sub monitor via DVI-I to D-Sub adapter

Connect a HDMI monitor via DVI-I to HDMI adapter

- 13 - Hardware Installation

You are now ready to proceed with the installation of the graphics card driver. Please refer to next

chapter for detailed instructions.

B-1.

Connect the GIGABYTE video adapter to the TV-

Out port on the graphics card

B-2.

Connect the SPDIF coaxial cable (optional)

to the video adapter and motherboard

Step 4.

To connect an HDMI TV, use either Method A or Method B below (depending on your motherboard

design) to enable the S/PDIF in function for the graphics card. It is recommended Method A be used on

motherboards that have a free S/PDIF header.

Method A (via the S/PDIF out header):

Connect the provided S/PDIF cable to the graphics card and the S/PDIF out header on your motherboard

(the red wire connects to the S/PDIF out pin and the black to the Ground pin).

Method B (via the coaxial S/PDIF out jack):

Connect the GIGABYTE video adapter to the TV-Out port on the graphics card. Insert one end of the

SPDIF coaxial cable (optional) into the S/PDIF in jack on the adapter and the other end into the coaxial

S/PDIF out jack on your motheboard.

A-1.

Connect the S/PDIF cable to the graphics card

A-2.

Connect the S/PDIF cable to the motherboard.

- 14 -GV-N26 Series Graphics Accelerator

GIGABYTE Video Adapter (optional item)

Connect to the TV-Out port on

the graphics card.

S-Video Out

HDTV Component

(Y+Pr+Pb)

AV Out

(1) Connecting HDTV

Connect your HDTV cables to the video adapter according to

the corresponding color.

(Y= Green, Pr= Red, Pb= Blue)

(2) Connecting S-Video

If your TV has a S-Video connection, connect the S-Video

cable from your TV to the S-Video Out port on the adapter.

(3) Connecting AV Output

If your TV has a Composite video connection, you can connect

the RCA cable from your TV to the AV Out port on the adapter.

- 15 - Hardware Installation

How NVIDIA

®

SLI

TM

(Scalable Link Interface) technology works:

In an SLI configuration, two/three SLI-ready graphics cards of the same model and the same manufac-

turers are connected together via SLI bridge connector in a system that provides two/three x16 PCI

Express slots to scale graphics performance. The picture below shows that two and three graphics

cards are linked in parallel in an SLI configuration.

SLI bridge connector

(provided by motherboard manufacturer)

Two SLI-ready graphics

cards of the same type.

(Example:

GV-N28-1GH-B)

3-Way SLI bridge connector

(provided by motherboard manufacturer)

Three SLI-ready graphics

cards of the same type.

(Example:

GV-N28-1GH-B)

SLI Configuration:

3-Way SLI Configuration:

- 16 -GV-N26 Series Graphics Accelerator

3. Software Installation

In this manual, we assume that your CD-ROM drive letter to be Drive D:

The installation of drivers is very simple. When you insert the driver CD into your CD-ROM drive, you

can see the autorun window (if it does not show up, run "D:\setup.exe"). Then you can follow the

instructions to setup your graphics card driver. (Please follow the subsection "3.1.3 Driver Installation"

to install the driver for your graphics card.)

3.1. Windows

®

XP Driver and Utilities Installation

3.1.1. Operating System Requirements

Notice the following guidelines before installing the drivers:

1. First make sure your system has installed DirectX 9.0c or later version.

2. Make sure your system has installed the appropriate motherboard drivers (for the motherboard

drivers, please contact the motherboard manufacturer.)

- 17 - Software Installation

3.1.2. DirectX Installation

Install Microsoft DirectX to enable 3D hardware acceleration support for Windows XP to achieve better

3D performance.

For software MPEG support in Windows XP, you must install DirectX first. Users who run

Windows XP with Service Pack 2 or above do not need to install DirectX separately.

Step 1.

When the autorun window shows up, click the

Install DirectX 9 item.

Step 2. Choose I accept the agreement

and click the Next button.

Step 3. Click the Next button.

The system is installing the components. Step 4. Click Finish to restart computer.

Then the DirectX 9 installation is completed.

- 18 -GV-N26 Series Graphics Accelerator

3.1.3. Driver Installation

A. New Hardware Found

When the graphics card is inserted into your computer for the first time, the operating system will detect

the graphics card automatically and display a New Hardware Found message. The following are step-

by-step installation instructions.

Step 1: Found New Hardware Wizard: Video Controller (VGA Compatible)

Click the Next button to install the driver. (Insert the

driver CD-ROM that came with your graphics card.)

Or click the Cancel button to install the driver from

the autorun window.

Step 2: Found New Hardware Wizard: Searching and Installing

The wizard will search for the driver and install it automatically.

Step 3: Found New Hardware Wizard: Finish

Click the Finish button to finish the installation.

- 19 - Software Installation

B. Driver Installation (Autorun Window)

Insert the driver CD-ROM into your CD-ROM drive. The autorun window will appear. If it does not show

up, please run "D:\setup.exe".

Step 1.

When the autorun window shows up, click the

Install Display Driver item.

Step 2. Click the Next button. The system is installing the components.

Step 3. Click the Finish button to restart the computer.

Then the driver installation is completed.

- 20 -GV-N26 Series Graphics Accelerator

3.1.4. GIGABYTE Gamer HUD Lite on Driver Disk ( for GV-N26OC-896H)

Step 1:

Click the GIGABYTE Gamer HUD Lite item.

Step 2:

Choose the language for the installation and click the OK button.

Step 3:

Click the Next button.

Step 4:

Click the Install button.

The system is installing the components. Step 5:

Click the Finish button. Then the installation of

the GIGABYTE Gamer HUD Lite is completed.

Page is loading ...

Gigabyte GV-N26OC-896H User manual

Gigabyte GV-N26OC-896H User manual

Related papers

Other documents