CNB NXE3055MR Owner's manual

CNB
Brand
CNB
Model
NXE3055MR
Category
Security cameras
Type
Owner's manual

CNB NXE3055MR is a powerful network weatherproof camera with advanced video/audio compression technology (MJPEG/H.264, G.711) and progressive technology for sharp and clear images. It supports 2-way audio, smart event features like motion detection with three different areas, and remote firmware upgrades. With hybrid IP technology, it can connect to existing analog CCTV systems. Use it for surveillance, remote video monitoring, or real-time broadcasting.

CNB NXE3055MR is a powerful network weatherproof camera with advanced video/audio compression technology (MJPEG/H.264, G.711) and progressive technology for sharp and clear images. It supports 2-way audio, smart event features like motion detection with three different areas, and remote firmware upgrades. With hybrid IP technology, it can connect to existing analog CCTV systems. Use it for surveillance, remote video monitoring, or real-time broadcasting.

XNET Network Weatherproof Camera Installation Manual
Ver. 1.2
XNET Network Weatherproof Camera
(NXE3055MR)
Installation Manual
2 / 23
Network Weatherproof Camera Installation Manual
About this Installation Guide
This product has been tested for compatibility and stability as per high performance standard.
This installation guide covers the installation and operation of Network weatherproof Camera only.
Please read this manual including the important cautions and warnings thoroughly before using the
product even if you are an expert.
Important Notices
The copyright of this manual is owned by Manufacturer.
It is illegal to copy and distribute this manual without permission.
Damages caused by misuse (i.e. use of parts not suggested) will not be covered under warranty.
Contact the store or the manufacturer immediately if there is any problem with the product.
Do not disassemble the product for alteration or repair.
This product complies for CE (Europe) and FCC (USA) regulations for industrial and home electrical
device.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
3 / 23
Network Weatherproof Camera Installation Manual
Index
1. About the product................................................................................................................. 4
1.1. Features of the product .................................................................................................. 4
1.2. Applications .................................................................................................................. 4
2. Product Description ............................................................................................................... 5
2.1. Contents ....................................................................................................................... 5
2.2. Product Information ....................................................................................................... 5
2.3. Hardware Designation .................................................................................................... 6
2.3.1. Switch and Controls ............................................................................................ 6
2.3.2. Internal configuration ......................................................................................... 7
2.3.3. Connecting to Cables .......................................................................................... 8
2.3.4. Alarm Device Connection .................................................................................. 10
2.3.5. Mounting the Camera ....................................................................................... 11
3. Software Installation............................................................................................................13
3.1. Installing system ..........................................................................................................13
3.2. IP-Installer and IP address Configuration ........................................................................18
3.2.1. About IP-Installer ............................................................................................. 18
3.2.2. IP Address Configuration ................................................................................... 18
4. Using Web Viewer ...............................................................................................................20
4.1. Logging In ...................................................................................................................20
4.2. Web Viewer Page ..........................................................................................................21
5. Specification .......................................................................................................................22
4 / 23
Network Weatherproof Camera Installation Manual
1. About the product
This Product is an internet based security and surveillance system that is compatible with various networks
with its easy installation, various user interfaces, and multi-functional compressor Codec such as H.264 and
MJPEG. The product provides reliable real-time surveillance by SXGA real time video/ audio, event-based local
storage, and hybrid IP technology that can be used with the existing analog CCTV systems.
1
1
.
.
1
1
.
.
F
F
e
e
a
a
t
t
u
u
r
r
e
e
s
s
o
o
f
f
t
t
h
h
e
e
p
p
r
r
o
o
d
d
u
u
c
c
t
t
Advanced Video/ Audio compression technology (MJPEG/H.264, G.711)
Progressive technology - Sharp and clear image with no ghost effect.
Hybrid IP Technology - Analog CCTV video output for connecting to an existing analog system.
Multi-Codec stream - Live video signal compression to MJPEG or H.264 for various applications.
2-way Audio - Bi-directional voice communication between Client’s PC and camera.
Smart Event feature - Motion detection, Alarm sensor/output, pre- and post- alarm for automated
surveillance with no need for an attendant or monitoring.
Installation Wizard - Easy and unified installation for large network.
Motion Detection with three different areas - Alarm output and Video/ Audio data transmission to FTP site
or e-mail.
Supports Various resolutions
-
1080P(1920X1080),SXGA(1280X1024),SXGA(1280X960),720P(1280X720),XGA(1024X768),D1(720X480),
VGA(640x480),CIF(352x240),QVGA(320X240),
Remote firmware upgrade over the network
1
1
.
.
2
2
.
.
A
A
p
p
p
p
l
l
i
i
c
c
a
a
t
t
i
i
o
o
n
n
s
s
Surveillance (Surveillance areas can be a building, store, factory, parking lot, financial institutions,
government buildings, military facilities, etc.)
Remote video monitoring (Monitoring areas can be a hospital, kindergarten, traffic monitoring, remote
branch office, weather, environment preservation, illegal disposal of trash, etc.)
Real time broadcasting over the internet (Broadcasting can be from a resort facility, parties, festivals,
remote business meetings, educational trainings, etc.)
5 / 23
Network Weatherproof Camera Installation Manual
2. Product Description
2
2
.
.
1
1
.
.
C
C
o
o
n
n
t
t
e
e
n
n
t
t
s
s
Please make sure the following contents are included in the package.
Contents
Description
Additional info.
Product
NXE3055MR
POWER ADAPTOR
AC Power Cable
INPUT : 100~240VAC 50-60Hz
OUTPUT : 12VDC 2A / AC24V 2.5A
2 Jack Power Cable for Outlet
BRACKET, SUNVISOR
BRACKET BASE:1EA
SUNVISOR : 1EA
CD
Software and User’s manual
DC Plug
AC/DC CONNECTOR
CVBS Cable
A Plug for DC Power Adaptor
Two Position Connector for Power
Input
BNC connector for Analog Video
Output
Accessory
L-WRENCH : 2EA
SCREW 4EA
Wall Anchors 4EA
Sunvisor Screws : 1EA
Nut : 4EA
2
2
.
.
2
2
.
.
P
P
r
r
o
o
d
d
u
u
c
c
t
t
I
I
n
n
f
f
o
o
r
r
m
m
a
a
t
t
i
i
o
o
n
n
NXE3055MR
Install CD
Viewer Program
(CMS)
IP Weatherproof Camera
(NXE3055MR)
A software for detecting the camera
in the network and assigning an IP
address
A software to monitor/record live Video
and audio from the camera
6 / 23
Network Weatherproof Camera Installation Manual
2
2
.
.
3
3
.
.
H
H
a
a
r
r
d
d
w
w
a
a
r
r
e
e
D
D
e
e
s
s
i
i
g
g
n
n
a
a
t
t
i
i
o
o
n
n
2
2
.
.
3
3
.
.
1
1
.
.
S
S
w
w
i
i
t
t
c
c
h
h
a
a
n
n
d
d
C
C
o
o
n
n
t
t
r
r
o
o
l
l
s
s
1. Motorize Lens : 3-9mm Motorize Lens
2. IR LED : IR Led light controlled by CDS Sensor.
3. CDS Sensor : senses the light intensity (low light level).
4. Casing Screws (front - 4EA) : attach the front and rear bodies together
5. Sunvisor : Shields off the direct sunlight to avoid overheating the camera module
6. Sunvisor Screws : fix the Sunvisor on the main body
7. Rotate adjusting Bolt: fixes the adjustment of the camera’s rotational angle.
8. Tilt adjusting Bolt: fixes the adjustment of the camera’s tilt angle.
9. Pan adjusting Bolt: fixes the adjustment of the camera’s pan angle.
10. FRONT BODY
11. Connecting Terminal: Please refer to 2.3.2. Connecting Terminal
12. REAR-BODY
7 / 23
Network Weatherproof Camera Installation Manual
2
2
.
.
3
3
.
.
2
2
.
.
I
I
n
n
t
t
e
e
r
r
n
n
a
a
l
l
c
c
o
o
n
n
f
f
i
i
g
g
u
u
r
r
a
a
t
t
i
i
o
o
n
n
1. Micro SD Card Slot :
Video images can be stored into a Micro SD card when an event occurs. Please use less than 16 GB
MICRO SD Memory.
Figure 2-3. MICRO SD CARD
2. Video Out: Analog Video output. When installing the camera, use this output to connect a CCTV
monitor to quickly check for desired image. The enclosed CVBS cable has an RCA termination.
(Enable Video Out in Camera’s menu to activate this Analog video output. The analog Video can only
be used in resolutions lower than VGA.)
3. Factory Reset Button : When the Camera is powered up, press and hold this button for 3 seconds
to reset the camera to factory default state
4. Autofocus Button : Adjust automatically the focus of the camera.
5. LINK LED: Yellow light indicates that the network is properly connected.
6. ACT LED: Green light indicates that the camera is connected to 100Mbps LAN. Also, the blinking
green light indicates that the system is receiving data.
7. PWR LED: Red light indicates that 12V DC/24V AC power is connected.
8 / 23
Network Weatherproof Camera Installation Manual
2
2
.
.
3
3
.
.
3
3
.
.
C
C
o
o
n
n
n
n
e
e
c
c
t
t
i
i
n
n
g
g
t
t
o
o
C
C
a
a
b
b
l
l
e
e
s
s
INPUT, OUTPUT
Alarm Connection
These wires connect to Alarm input/output devices.
Alarm Sensor Input: Connect to an Alarm sensor device such as an IR Sensor or a Heat sensor. The
operation of this input can be configured to either normally close or normally open.
Alarm Output: Connect to a relay that drives alarm devices such as a Siren Lamp or an Alarm Light.
The operation of this output can be configured to either normally close or normally open.
Please refer to “2.3.4 Connection to Alarm Devices” for detailed instruction on how to connect a
sensor and a relay.
POWER IN VIDEO OUT
Power Input
Use the cable adapter (DC12V JACK) in the package to connect power.
Please use the power supply provided in the package.
When connecting to a power supply, please note the following power ratings and the
diagrams below: (DC12V/2A, AC24V 2.5A)
Analog Video Output
This output can be used to check the video during the installation.
Use the supplied BNC connector
Connect the adapter to a video cable with BNC termination.
(Select Video Out in menu to enable this output)
9 / 23
Network Weatherproof Camera Installation Manual
Audio Connection
MIC/Line Input (Mono) RED
Connect this wire to the Audio input. The audio input can come from a microphone or an Audio device.
Line Output (Mono) WHITE
This is an Audio signal output to a Power Amplified device or a Speaker. In two way audio
communication using the camera, this can be used to listen to the audio from a remote PC.
Network Cable
This RJ-45 Ethernet terminal connects to a 100Mbps LAN. When an optional PoE is used, the power will be
supplied from the Network Cable. Network cable of this product is not water-resistant.
Do not use the other power connector when powering up the product
through PoE. The Product is not covered under warranty when it is
damaged by connecting both Ethernet power and 12V DC power (or 24V
AC power) to this terminal.
10 / 23
Network Weatherproof Camera Installation Manual
2
2
.
.
3
3
.
.
4
4
.
.
A
A
l
l
a
a
r
r
m
m
D
D
e
e
v
v
i
i
c
c
e
e
C
C
o
o
n
n
n
n
e
e
c
c
t
t
i
i
o
o
n
n
Alarm Input
Various alarm sensor types (IR, heat, magnetic, etc.) can be connected to Alarm input (+)/(-) terminal as
shown in figure 2.5. (NC or NO can be configured in Menu.)
Please note that the Alarm Sensor device requires a separate power source.
Alarm in(+)
Alarm in(-)
Photo Coupler
Sensor
Device
Signal(+5 ~ 30VDC)
GND
Adaptor
+
-
Internal Circuitry External Circuitry
Alarm Output
This terminal can only drive up to DC 30V/400mA. A relay has to be used to operate Alarm devices that
require higher voltage or current.
ALARM
DEVICE
POWER
Alarm out
Alarm out
+
+
-
-
Internal Circuitry External Circuitry
11 / 23
Network Weatherproof Camera Installation Manual
2
2
.
.
3
3
.
.
5
5
M
M
o
o
u
u
n
n
t
t
i
i
n
n
g
g
t
t
h
h
e
e
C
C
a
a
m
m
e
e
r
r
a
a
Sunvisor
Install Sunvisor to the Camera’s main body using Sunvisor , washers, and screws.
Mounting the Camera
Ceiling Mount type Wall Mount Type
Mount the Bracket Base on the installation surface using the four 6mm screws provided.
Mount the camera’s main body on the Bracket Base using the four 5/16” screws provided as
shown in the figure.
.
12 / 23
Network Weatherproof Camera Installation Manual
Adjusting the Camera Angle
Ceiling Mount type Wall Mount Type
After mounting the Camera, unlock the fixing screws shown in the picture using the L wrench provided to
adjust the camera’s angle as desired. Tighten the fixing screws back when done.
13 / 23
Network Weatherproof Camera Installation Manual
3. Software Installation
This is a quick installation guide for IP Installer software. IP Installer software helps you monitor the camera’s
Video and Audio in an easy user interface. If you have questions about details not explained in this section or
if the product is not functioning as described, please contact the manufacturer.
3
3
.
.
1
1
.
.
I
I
n
n
s
s
t
t
a
a
l
l
l
l
i
i
n
n
g
g
s
s
y
y
s
s
t
t
e
e
m
m
Connecting the camera Directly to a PC
The camera can be directly connected to a PC for configuration.
A. Connect the camera to your PC directly using a crossover LAN cable as shown below.
NOTE: The camera will set its IP address to the default value,
192.168.123.100, after looking for a DHCP service.
(This process approximately takes 20~30 seconds)
B. Next, change the PC’s network configuration in the following window:
Windows Start Control Panel Network Connections Right-clicks on the Local Area Connection
icon Double click on the Internet Protocol (TCP/IP) icon.
Set PC’s network configuration as below:
COMPUTER
Crossover
Network Cable
14 / 23
Network Weatherproof Camera Installation Manual
NOTE: IP address of the PC can be set in anywhere between 192.168.123.2 and
192.168.123.254 except for 192.168.123.100, which is taken by the camera.
C. Insert the Setup CD into your CD-ROM drive, and install
IPInstaller software.
D. Click ‘Next’ when the Installation Wizard box pops up.
E. Click ‘Install’ to begin the Installation.
15 / 23
Network Weatherproof Camera Installation Manual
F. Click ‘Finish’ to complete the installation.
G. IP Installer will launch automatically as shown below. Double click on the camera from the list.
16 / 23
Network Weatherproof Camera Installation Manual
H. When the camera is successfully connected to your PC, you’ll see the camera’s IP address on the IP
installer software.
(Internet Explorer will prompt you to install ActiveX.
Please accept the ActiveX download in order to view video. )
NOTE: Click on Setting in the main screen to change the configurations of the camera.
Enter the default User name and Password when the login prompt opens up.
Default User name : root Default Password : admin
17 / 23
Network Weatherproof Camera Installation Manual
Connecting the Camera to a router
camera can be connected to the router of an existing LAN. Please connect the camera to a router
using a LAN cable as shown below:
`
NOTE: If the DHCP server is enabled at your router, camera will automatically receive an
IP address from the router. Otherwise, camera’s IP address will be automatically set to
the default value, 192.168.123.100.
COMPUTER
Direct Network
Cable
NETWORK HUB
18 / 23
Network Weatherproof Camera Installation Manual
3
3
.
.
2
2
.
.
I
I
P
P
-
-
I
I
n
n
s
s
t
t
a
a
l
l
l
l
e
e
r
r
a
a
n
n
d
d
I
I
P
P
a
a
d
d
d
d
r
r
e
e
s
s
s
s
C
C
o
o
n
n
f
f
i
i
g
g
u
u
r
r
a
a
t
t
i
i
o
o
n
n
3
3
.
.
2
2
.
.
1
1
.
.
A
A
b
b
o
o
u
u
t
t
I
I
P
P
-
-
I
I
n
n
s
s
t
t
a
a
l
l
l
l
e
e
r
r
In order to have the camera viewable on the network, an IP address has to be assigned first. A software
called IP-Installer (provided in the Installation CD) will help you assign the IP address easily. If your network
uses a DHCP server, the server will automatically assign an IP addresses to the camera. If your network does
not have a DHCP server, the camera will assign itself a default IP address, 192.168.123.100. For detail, refer
to the user’s manual of the IP Installer.
3
3
.
.
2
2
.
.
2
2
.
.
I
I
P
P
A
A
d
d
d
d
r
r
e
e
s
s
s
s
C
C
o
o
n
n
f
f
i
i
g
g
u
u
r
r
a
a
t
t
i
i
o
o
n
n
A. The following window will appear when you start the IP-installer.
Figure 3-1. IP Installer Main window
B. Select the camera of which you wish to change the IP address and click on (Set IP Address)
icon to bring up the box shown in Figure 3-3.
Figure 3-2. Set IP Address box
19 / 23
Network Weatherproof Camera Installation Manual
C. When you enter the IP address and click Set button, the box shown in Figure 3-4 will appear.
Figure 3-3. Select Network Adapter Box
D. Select the adapter and click Select button to complete changing the IP address of the camera.
20 / 23
Network Weatherproof Camera Installation Manual
4. Using Web Viewer
You can connect to the camera using your internet browser or a software called “CMS”. This section covers
the connection through your web browser only. For instructions on how to configure the network connection
using the CMS software, please refer to the manual for the CMS, which can be found in the installation CD.
4
4
.
.
1
1
.
.
L
L
o
o
g
g
g
g
i
i
n
n
g
g
I
I
n
n
Enter the IP address of the camera on the address bar of your web browser.
Then the following webpage will appear:
Figure 4-1. Log-in Box
Enter the user name and password to go to the web viewer page. The default id and password is “root”
and “admin”. If you have changed the HTTP port number from the default value, put a colon and the
port number at the end of the IP address. (For example, enter the following address when you changed
the port to 8080: http://192.168.123.100:8080)
<Address format for accessing as an administrator>
(When using the default IP address and port number)
http://192.168.123.100
(When the IP address and port number have been changed) http://IP
address: new port number
If you forget the administrator’s password, “Factory Reset” is the only way to regain access.
However, since this will retrieve all default settings, the network settings have to be configured
again using the IP installer.
For security, please change the administrator’s id and password from their default values. Please
save the changed ID and password in a place only accessible by an administrator. Please refer to
[User Manual] for detail.
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23

CNB NXE3055MR Owner's manual

CNB
Brand
CNB
Model
NXE3055MR
Category
Security cameras
Type
Owner's manual

CNB NXE3055MR is a powerful network weatherproof camera with advanced video/audio compression technology (MJPEG/H.264, G.711) and progressive technology for sharp and clear images. It supports 2-way audio, smart event features like motion detection with three different areas, and remote firmware upgrades. With hybrid IP technology, it can connect to existing analog CCTV systems. Use it for surveillance, remote video monitoring, or real-time broadcasting.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents