Blaupunkt San Francisco 320 Owner's manual

Brand: Blaupunkt

Model: San Francisco 320

Category: Car media receivers

Type: Owner's manual

Operating and installation instructions

www.blaupunkt.com

Toronto 420 BT 1 011 202 420 / 1 011 202 421

San Francisco 320 1 011 202 320 / 1 011 202 321

Car Radio

USB

Bluetooth

button

Unlock the detachable control panel

MENU button

Short press: Call up/close menu

Long press: Start scan function

On/O button

Short press: Switch on car sound system

In operation: Mute car sound system (Mute)

Long press: Switch o car sound system

Volume control

CD tray

Display

Rotary control

In the menu: Change menu level,

select menu item, change setting

Radio mode: Set frequency,

start station/PTY seek tuning

CD/MP3/WMA/iPod mode:

Track selection, fast forward/reverse

Browse mode in MP3/WMA/iPod mode: ID3

category (iPod only), select folder and track

button (Eject)

Eject a CD

Microphone (Toronto 420 BT only)

USB port

;

Front AUX-IN socket

button (only Toronto 420 BT)

Ending/rejecting a phone call

button (Toronto 420 BT only)

Short press: Answering a call, speed dial

Long press: Open the phone book of the cell

phone or activate voice dialing

Keys 1 - 5

Infrared receiver

SRC button

Select memory bank or audio source

DIS button

Short press: Switch display

Long press: Switch display brightness

SD card slot

Access only with detached control panel

Controls

3 5 621 8

12131617 14

4 7

11 10

Contents

Safety notes ...................................................... 4

Symbols used .............................................................. 4

Road safety .................................................................. 4

General safety notes ................................................. 4

Declaration of conformity ...................................... 5

Cleaning notes .................................................. 5

Disposal notes................................................... 5

Scope of delivery .............................................. 5

Optional equipment

(not part of the scope of delivery) .......................5

Placing the device in operation ....................... 5

Attaching/detaching the control panel ............ 5

Display language (only Toronto 420 BT) ........... 6

Setting the reception area ..................................... 6

Switching on/o ........................................................ 6

Volume .......................................................................... 6

Display brightness ..................................................... 7

Switching demo mode on/o ............................... 7

Tra c information ............................................ 7

Radio mode ....................................................... 7

RDS.................................................................................. 7

Changing to radio mode or selecting

a memory bank .......................................................... 8

Tuning into a station ................................................ 8

Storing stations or calling stored stations ........ 8

Scanning stations ...................................................... 8

Storing stations automatically (Travelstore) .... 9

PTY .................................................................................. 9

Con guring the display .........................................10

CD/MP3/WMA/iPod mode .............................. 10

Basic information .....................................................10

Changing to CD/MP3/WMA/iPod mode .........11

Inserting/ejecting a CD .........................................11

Connecting/removing a USB data carrier .......11

Inserting/removing the memory card .............12

Selecting tracks ........................................................12

Fast searching ...........................................................12

Interrupting playback ............................................12

Scanning all tracks ..................................................12

Playing tracks in random order ..........................13

Repeatedly playing individual tracks or

directories ..................................................................13

Con guring the display .........................................13

Browse mode ............................................................14

Searching by track names

(not in iPod mode) ..................................................15

Bluetooth®

(Toronto 420 BT only) ..................................... 15

Bluetooth® menu .....................................................15

Pairing and connecting a device .......................16

Telephone functions...............................................17

Bluetooth® streaming mode................................20

Phone book functions ...........................................20

Additional functions in

the Bluetooth® menu .............................................21

External audio sources ................................... 23

Front AUX-IN socket ................................................23

Sound settings ................................................ 23

Calling and exiting the "AUDIO" menu ............23

Making settings in the "AUDIO" menu .............24

Setting the 3-band equaliser ...............................25

User settings ................................................... 26

Calling the user menu and selecting

a menu .........................................................................26

Making settings in the "TUNER" menu ............27

Making settings in the "DISPLAY" menu .........28

Making settings in the "VOLUME" menu ........29

Making settings in the "CLOCK" menu ............30

Making settings in the "VARIOUS" menu ........30

Factory settings .............................................. 31

Useful information ......................................... 32

Warranty .....................................................................32

Service .........................................................................32

Technical data ................................................. 32

Installation instructions ................................ 33

Safety notes

The car sound system was manufactured accord-

ing to the state of the art and established safety

guidelines. Even so, dangers may occur if you do

not observe the safety notes in these instructions.

These instructions contain important informa-

tion to easily and safely install and operate the car

sound system.

• Read these instructions carefully and com-

pletely before using the car sound system.

• Keep the instructions at a location so that they

are always accessible to all users.

• Always pass on the car sound system to third

parties together with these instructions.

In addition, observe the instructions of the devices

used in conjunction with this car sound system.

Symbols used

These instructions employ the following symbols:

DANGER!

Warns about injuries

CAUTION!

Warns about damaging the CD drive

DANGER!

Warns about high volume

The CE mark con rms the compliance

with EU directives.

쏅 Identi es a sequencing step

• Identi es a listing

Road safety

Observe the following notes about road safety:

• Use your device in such a way that you can

always safely control your vehicle. In case of

doubt, stop at a suitable location and operate

your device while the vehicle is standing.

• Remove or attach the control panel only

while the vehicle is standing.

• Always listen at a moderate volume to pro-

tect your hearing and to be able to hear acous-

tic warning signals (e.g. police sirens). During

mute phases (e.g. when changing the audio

source), changing the volume is not audible.

Do not increase the volume during this mute

phase.

General safety notes

Observe the following notes to protect yourself

against injuries:

• Do not modify or open the device. The device

contains a Class 1 laser that can cause injuries

to your eyes.

• Do not increase the volume during mute

phases, e.g. when changing the audio source.

Changing the volume is not audible during a

mute phase. Do not increase the volume dur-

ing mute phases, e.g. when changing the audio

source.

Use as directed

This car sound system is intended for installation

and operation in a vehicle with 12 V vehicle sys-

tem voltage and must be installed in a DIN slot.

Observe the performance limits in the technical

data. Repairs and installation, if necessary, should

be performed by a specialist.

Installation instructions

You may only install the car sound system your-

self if you are experienced in installing car sound

systems and are very familiar with the electrical

system of the vehicle. For this purpose, observe

the installation instructions at the end of these

instructions.

Safety notes

Safety notes | Cleaning notes | Disposal notes | Scope of delivery | Placing the device in operation

Declaration of conformity

The Blaupunkt AudioVision GmbH & Co. KG de-

clares that the car sound system San Francisco

320 complies with the basic requirements and

the other relevant regulations of the directive

2004/108/EEC and the car sound system Toronto

420 BT complies with the basic requirements and

the other relevant regulations of the directive

1999/5/EC.

The declaration of conformity can be found on the

Internet under www.blaupunkt.com.

Cleaning notes

Solvents, cleaning and scouring agents as well as

dashboard spray and plastics care product may

contain ingredients that will damage the surface

of the car sound system.

• Use only a dry or slightly moistened cloth for

cleaning the car sound system.

• If necessary, clean the contacts of the control

panel regularly using a soft cloth moistened

with cleaning alcohol.

Disposal notes

Do not dispose of your old unit in the house-

hold trash!

Use the return and collection systems available to

dispose of the old device.

Scope of delivery

The scope of delivery includes:

1 Car sound system

1 Operating/installation instructions

1 Case for the control panel

1 Support frame

1 Antenna connection adapter

Extended scope of delivery

(for 1011202321 / 1011202421 only):

1 Handheld remote control (incl. battery)

1 Connecting cable chamber A

1 Connecting cable chamber B

Optional equipment

(not part of the scope of delivery)

Use only accessories approved by Blaupunkt.

Information is available from your Blaupunkt

specialised dealer or on the Internet under

www.blaupunkt.com.

Placing the device in operation

Caution!

Transport securing screws

Before the startup of the car sound system, ensure

that the transport securing screws are removed

(see the chapter "Installation instructions").

Attaching/detaching the control

panel

The car sound system is equipped with a detach-

able control panel (release panel) to protect your

equipment against theft. In the delivery state, the

control panel is in the supplied case. To start oper-

ating the radio after installation, you must  rst at-

tach the control panel (see the section "Attaching

the control panel" in this chapter).

Always take the control panel with you when leav-

ing the vehicle. The car sound system is worthless

to a thief without this control panel.

Caution

Damage to the control panel

Never drop the control panel.

Transport the control panel so that it is protected

against impacts and the contacts cannot become

dirty.

Do not expose the control panel to direct sunlight

or another heat source.

Avoid direct skin contact with the control panel's

electrical contacts.

Placing the device in operation

Attaching the control panel

쏅 Push the control panel into the bracket at the

right edge of the device.

쏅 Push the control panel carefully into the left

bracket until it clicks into place.

Removing the control panel

쏅 Press the

button

to unlock the control

panel.

The left side of the control panel detaches

from the device and is secured by the bracket

against falling out.

쏅 Move the control panel slightly to the left until

it disengages from the right bracket.

쏅 Carefully remove the control panel from the

left bracket.

Note:

The car sound system automatically switches

o as soon as the control panel is removed.

Display language

(only Toronto 420 BT)

For the Toronto 420 BT, you can de ne whether the

language for messages on the display is English or

German. The setting is performed in the user menu

(see the chapter "User settings", section "Mak-

ing settings in the "DISPLAY" menu", menu item

" LANGUAGE").

Setting the reception area

This car sound system is designed for operation in

di erent regions with di erent frequency ranges

and station technologies. The factory default of

the reception area is "EUROPE". In addition, the

reception areas "USA", "SOUTH AMERICA" and

" THAILAND" are available.

Note:

If you operate the car sound system outside of

Europe, you may  rst have to set a suitable re-

ception area in the user menu (see the chapter

"User settings", section "Making settings in the

"TUNER" menu", menu item "TUNER AREA").

Switching on/o

Switching on/o with the On/O button

쏅 For switch-on, press the On/O button

The car sound system switches on.

쏅 To switch o the device, press and hold down

the On/O button

for longer than 2 sec-

onds.

The car sound system switches o .

Note:

If you switch on the car sound system while

the vehicle ignition is switched o , it auto-

matically switches o after 1 hour to preserve

the vehicle battery.

Switching on/o via vehicle ignition

The car sound system will switch o /on simulta-

neously with the ignition if the device is correctly

connected to the vehicle's ignition as shown in the

installation instructions and you did not switch

the device o by pressing the On/O button

Volume

Adjusting the volume

You can adjust the volume in steps from 0 (o ) to

50 (maximum).

쏅 Turn the volume control

to change the

volume.

Note:

If a telephone or navigation system is con-

nected with the car sound system as de-

scribed in the installation instructions (pin

2 of chamber A), the car sound system is

muted in case of a telephone call or naviga-

tion announcement so that you can hear the

playback of the telephone or navigation sys-

tem undisturbed. During muting, the display

shows "TELEPHONE".

Muting the car sound system (Mute)

쏅 Brie y press the On/O button

to mute

the car sound system or to reactivate the pre-

vious volume.

While it is muted, the display shows "MUTE".

Placing the device in operation | Tra c information | Radio mode

Display brightness

You can manually switch the display brightness

between daytime mode and night-time mode or

switch automatically with the driving lights of the

vehicle.

Note:

The manual or automatic switching of the

display brightness is selected in the user

menu (see the chapter "User settings",

section "Making settings in the "DISPLAY"

menu", menu item "DIMMER").

쏅 Press the DIS button

for approx. 2 seconds

to start scanning.

Switching demo mode on/o

The demo mode shows the functions of the car

sound system as scrolling text on the display. By

pressing any button, the demo mode is interrupt-

ed and you can operate the device.

The demo mode can be switched on and o in the

user menu (see the chapter "User settings", section

"Making settings in the "VARIOUS" menu", menu

item "DEMO MODE").

Tra c information

In the reception area "EUROPE", an FM station can

identify tra c reports by means of an RDS signal.

If priority for tra c reports is switched on, a traf-

 c report is automatically switched through, even

if the car sound system is currently not in radio

mode.

If priority is switched on, the display shows the

tra c jam symbol (

). "TRAFFIC" is displayed

during a switched-through tra c announcement.

The priority is activated and deactivated in the

user menu (see the chapter "User settings", sec-

tion "Making settings in the "TUNER" menu", menu

item "TRAFFICINFO").

Notes:

• The volume is increased for the duration

of the switched-through tra c announce-

ment. You can adjust the minimum volume

for tra c announcements (see the chapter

"User settings", section "Making settings in

the "VOLUME" menu", menu item "TRAFFIC

VOL").

• To cancel a switched-through tra c an-

nouncement, press the SRCbutton

Radio mode

RDS

Many FM stations broadcast an RDS (Radio Data

System) signal in addition to their programme in

the reception area "EUROPE" that allows the follow-

ing additional functions:

• The station name is shown on the display.

• The car sound system recognises tra c an-

nouncements and news broadcasts and can

automatically switch them through in other

operating modes (e.g. in CD mode).

• Alternate frequency: If RDS is activated, the car

sound system automatically selects the best

receivable frequency for the station that is cur-

rently set.

• Regional: At certain times, some radio stations

divide their programme into regional pro-

grammes providing di erent content. If the

REGIONAL function is activated, the car sound

system changes only to those alternate frequen-

cies on which the same regional programme is

being broadcast.

The functions RDS and REGIONAL are activated

and deactivated in the user menu (see the chap-

ter "User settings", section "Making settings

in the "TUNER" menu", menu items "RDS" and

" REGIONAL").

Note:

If you adjust a di erent reception area than

"EUROPE", RDS is automatically switched o .

The station name continues to be shown on

the display. If you want to use radio stations

with RDS features in your region, switch on

RDS in the user menu.

Radio mode

Changing to radio mode or selecting

a memory bank

The following memory banks are available in the

di erent reception areas:

Region Memory banks

EUROPE FM1, FM2, FMT, MW, LW

USA FM1, FM2, FMT, AM, AMT

SOUTH AMERICA FM1, FM2, FMT, AM, AMT

THAILAND FM1, FM2, FMT, AM, AMT

쏅 Press the SRCbutton

repeatedly until the

desired memory bank is displayed.

Notes:

• Up to 5 stations can be stored in each

memory bank.

• You can disable certain memory banks

that you do not want to use (see chapter

"User settings", section "Making settings

in the "TUNER" menu", menu item "BAND

SELECTION"). Deactivated memory banks

are skipped during the source selection

with the SRCbutton

Tuning into a station

There are various ways of tuning into a station:

Starting station seek tuning

쏅 Turn rotary control

one notch counter-

clockwise or clockwise to start station seek

tuning.

The display brie y shows "SEARCH AUTO".

The radio tunes into the next receivable sta-

tion.

Notes:

• For the reception area "EUROPE": In the FM

waveband, only tra c information stations

are tuned into if the priority for tra c infor-

mation ( ) is switched on.

• The sensitivity of seek tuning can be ad-

justed (see the chapter "User settings",

section "Making settings in the "TUNER"

menu", menu item "SENSITIVITY").

Tuning into stations manually

쏅 Press the rotary button

once to activate

manual station tuning.

The display brie y shows "SEARCH MANUAL".

쏅 Turn the rotary control 

to change the fre-

quency in increments.

Note:

The manual station tuning is automatically

exited approx. 15 seconds after the last fre-

quency change, and the station seek tuning is

started by turning the rotary control

Storing stations or calling stored

stations

쏅 Select the desired memory bank.

쏅 If necessary, set the desired station.

쏅 Press the station button 1 - 5

for approx.

2 seconds to store the current station under

the button.

- or -

쏅 Brie y press the station button 1 - 5

to call

up the stored station.

Scanning stations

With the scan function, you can scan either every

receivable station or every stored station of the

current waveband.

Note:

You can adjust the scan time for each station

(see the chapter "User settings", section "Mak-

ing settings in the "VARIOUS" menu", menu

item "SCAN TIME").

Scanning all receivable stations of the

waveband

쏅 Press the MENU button

for approx. 2 sec-

onds to start scanning.

During the scan, the display alternately dis-

plays "SCAN" and the current frequency as

well as memory bank or station name.

쏅 Brie y press the MENU button

to con-

tinue listening to the station that is currently

being scanned.

Radio mode

Scanning all stored stations of the waveband

쏅 Press the rotary control

for approx. 2 sec-

onds to start the scanning.

During the scan, the display alternately dis-

plays the current frequency as well as memo-

ry bank and location or station name.

쏅 Brie y press the rotary control

to continue

listening to the station that is currently being

scanned.

Storing stations automatically

(Travelstore)

With Travelstore, you can automatically search for

and store the 5 FM stations o ering the strongest

reception in the region in one memory bank. Any

previously stored stations in this memory bank are

deleted in the process.

With Travelstore, you can store 5 FM stations in

the FMT memory bank in all reception areas. In

the reception areas "USA", "SOUTH AMERICA" and

"THAILAND", you can also store 5 AM stations in

the AMT memory bank.

쏅 Select a memory bank of the desired wave-

band, e.g. FM1 or AM.

쏅 Press the SRCbutton

for approx. 2 sec-

onds.

The tuner starts the automatic station seek

tuning; the display shows "FM TSTORE" or

"AM TSTORE". After the storing is completed,

the radio plays the station at memory location

1 of the FMT or AMT level.

Notes:

• For the reception area "EUROPE": If the

priority for tra c information is switched

on ( ), only tra c information stations

are stored.

• If the FMT or AMT memory bank is deac-

tivated (see the chapter "User settings",

section "Making settings in the "TUNER"

menu", menu item "BAND SELECTION"), it

is automatically reactivated if you initiate

the Travelstore function.

PTY

In the reception areas "EUROPE" and "USA", an FM

station can transmit its current programme type,

e.g. CULTURE, POP, JAZZ, ROCK, SPORT or SCIENCE.

Hence, the PTY function allows a targeted search

for broadcasts of a certain programme type, e.g.

for rock or sports broadcasts. Note that PTY is not

supported by all stations.

Note:

The PTY function is only available if it has been

activated (see the chapter "User settings", sec-

tion "Making settings in the "TUNER" menu",

menu item "PTY").

Selecting a programme type

To select a programme type. read the section

"Making settings in the "TUNER" menu", menu

item "PTY TYPES" in the chapter "User settings".

Note:

In the reception area "EUROPE", you can adjust

the language in which the programme types

are displayed (see the chapter "User settings",

section "Making settings in the " TUNER"

menu", menu item "PTY LANGUAGE").

Searching for stations

Prerequisite: PTY function is switched on.

쏅 Press the rotary control

twice.

The display brie y shows "SEARCH PTY".

쏅 Turn rotary control

one notch counter-

clockwise or clockwise to start the PTY seek

tuning.

During the seek tuning, "SEARCH" and the

currently selected programme type are

shown on the display.

As soon as a station with the desired pro-

gramme type is found, it remains being tuned

into.

Notes:

• If no station with the selected programme

type is found, "NO PTY" is brie y displayed

and 2 beeps can be heard. The radio will

then retune to the station that it played

last.

• If the tuned radio station or another sta-

tion on the broadcasting network broad-

casts your selected programme type at a

later point in time, the car sound system

will automatically switch from the cur-

rently tuned station or from the current

audio source (e.g. CD) to the station whose

programme type matches the one you se-

lected. Note that this function is not sup-

ported by all stations.

Con guring the display

쏅 Press the DIS button

to toggle between

these displays:

Display Meaning

ABCDEF Station name

FM1 P1 89.90

Memory bank/memory

location/frequency

FM1 P1 08:40

Memory bank/memory

location/time

CD/MP3/WMA/iPod mode

Basic information

CD/MP3/WMA mode

This car sound system can be used to play audio

CDs (CDDA) and CD-R/RWs with audio, MP3 or

WMA  les as well as MP3 or WMA  les on USB data

carriers and SD(HC)/MMC memory cards.

Notes:

• To ensure proper functioning, use only CDs

with the Compact-Disc logo.

• Blaupunkt cannot guarantee the  awless

function of copy-protected CDs and all

CD blanks, USB data carriers and memory

cards available on the market.

Note the following information when preparing

an MP3/WMA data carrier:

• Naming of tracks and directories:

– Max. 32 characters without the  le exten-

sion ".mp3" or ".wma" (the use of more

characters reduces the number of tracks

and folders that the car sound system can

recognise)

– No umlauts or special characters

• CD formats: audio CD (CDDA), CD-R/RW,

Ø: 12 cm

• CD data formats: ISO 9669 Level 1 and 2, Joliet

• CD burn speed: Max. 16x (recommended)

• USB format/ le system: Mass storage device/

FAT16/32

• Memory card  le system: FAT16/32

• File extension of audio  les:

– .MP3 for MP3  les

– .WMA for WMA  les

•WMA  les only without Digital Rights Manage-

ment (DRM) and created with Windows Media

Player version 8 or later

• MP3 ID3 tags: Version 1 and 2

• Bitrate for creating audio  les:

– MP3: 32 to 320 kbps

– WMA: 32 to 192 kbps

• Maximum number of  les and directories: Up

to 30,000  les/500 directories depending on

the data structure

iPod mode

You can connect numerous iPod and iPhone mod-

els to the car sound system via the USB port in the

front of the device and the USB port at the rear

and control the audio playback from the car sound

system.

Notes:

• Blaupunkt cannot guarantee the  awless

function of all iPod and iPhone models.

• If an iPhone and iPod are connected at the

same time, the devices are charged via the

USB ports. If two iPhones are connected at

the same time, charging is not possible.

Use a suitable adapter cable to connect your iPod

or iPhone with the USB port of the car sound sys-

tem.

Radio mode | CD/MP3/WMA/iPod mode

Changing to CD/MP3/WMA/iPod

mode

쏅 Press the SRCbutton

repeatedly until the

desired audio source is displayed:

• "CD": Inserted CD.

• "SD(HC)": Inserted memory card

• "USB FRONT" or "USB REAR": USB data

carrier connected to the front or rear.

• "IPOD FRONT" or "IPOD REAR": iPod con-

nected to the front or rear

• "AUX": Connected external audio source.

Notes:

• The respective audio source can be select-

ed only if a corresponding CD is inserted or

a corresponding device is connected.

• A connected iPod is initially selected un-

der "USB" and, as soon as the iPod is recog-

nised, under "IPOD".

• If the car sound system  rst has to read

the data of a connected device or data car-

rier before the playback, the display shows

"READING". The duration of the reading

depends on the data volume and design

of the device or data carrier. If the device

or data carrier is defective or the trans-

ferred data cannot be played back, a corre-

sponding message appears on the display

(e.g. "CD ERROR").

Inserting/ejecting a CD

Inserting a CD

Risk of severe damage to the CD

drive!

Noncircular contoured CDs (shape CDs)

and CDs with a diameter of 8 cm (mini CDs) must

not be used.

We accept no responsibility for any damage to the

CD drive that may occur as a result of the use of

unsuitable CDs.

Note:

You must not hinder or assist the drive as it

automatically draws in the CD.

쏅 Insert the CD with its printed side up into the

CD tray

until you feel a slight resistance.

The drive automatically draws in the CD and

checks its data. Afterwards, the playback

starts in CD or MP3 mode.

Note:

If the inserted CD cannot be played back, "CD

ERROR" is brie y displayed and the CD is au-

tomatically ejected after approx. 2 seconds.

Ejecting a CD

Note:

You must not hinder or assist the drive as it

ejects the CD.

쏅 Press the

button

to eject an inserted

CD.

Notes:

• If a CD is ejected and not removed, the

drive will automatically draw it back in

again after approx. 10 seconds.

• You can also eject CDs while the car sound

system is switched o or whilst another au-

dio source is activated.

Connecting/removing a USB data

carrier

Note:

You can connect USB data carriers to the USB

port at the front of the device as well as the

rear USB port.

Connecting a USB data carrier

쏅 Switch o the car sound system so that the

data carrier will be correctly registered.

쏅 First, pull the protective cap of the USB port

to the front until it moves out of the port

and fold it to the right to connect a data car-

rier to the USB port at the front of the device.

쏅 Connect the USB data carrier.

쏅 Turn on the car sound system.

CD/MP3/WMA/iPod mode

If the USB data carrier is initially selected as

audio source, the data are read  rst.

Notes:

• If the connected USB data carrier cannot

be seen, "USB ERROR" is brie y displayed.

• The time required for reading in the data

depends on the design and size of the USB

data carrier.

Removing a USB data carrier

쏅 Switch o the car sound system so that the

data carrier will be correctly unregistered.

쏅 Disconnect the USB data carrier.

쏅 After you pulled o the data carrier from the

USB port at the front of the device, close the

protective cap of the USB port

Inserting/removing the memory card

Inserting the memory card

쏅 Detach the control panel.

쏅 Insert the memory card with its labelled side

up and its contacts  rst into the card slot

until it clicks into place.

쏅 Attach the control panel.

After switch-on, the device automatically

selects the inserted memory card as audio

source. The data of the memory card are be-

ing read. Afterwards, the playback starts in

MP3 mode.

Notes:

• If the inserted memory card cannot be

played, "SD ERROR" is brie y displayed.

• The time required for reading the card

depends on the design and size of the

memory card.

Removing the memory card

쏅 Detach the control panel.

쏅 Push on the memory card until it disengages.

쏅 Pull the memory card out of the card slot

쏅 Attach the control panel.

Selecting tracks

쏅 Turn rotary control

one notch counter-

clockwise or clockwise to change to the pre-

vious/next track.

Notes:

• If you turn rotary control

several

notches counter-clockwise or clockwise,

you jump forward or reverse by the corre-

sponding number of tracks.

• If the current track plays longer than 3

seconds and you turn rotary control

one notch counter-clockwise or clockwise,

the tracks starts playing again.

Fast searching

쏅 Press the rotary control

once.

The display brie y shows "CUE/REVIEW".

쏅 Turn the rotary control

until the desired

position has been reached.

Note:

If you press the rotary control

twice, the

display brie y shows "TRACK SELECT". By

turning the rotary control

, you select a

di erent track.

Interrupting playback

쏅 Press the 3 button

to interrupt the

playback ("PAUSE") or to continue it.

Scanning all tracks

The scan function scans all available tracks.

쏅 Press the rotary control

for approx. 2 sec-

onds to start the scan, or brie y to continue

playing the currently scanned track.

During the scan, the display alternately dis-

plays "SCAN" and the current track number

or  le name.

Note:

The scan time can be adjusted (see the chap-

ter "User settings", section "Making settings

in the "VARIOUS" menu", menu item "SCAN

TIME").

CD/MP3/WMA/iPod mode

Playing tracks in random order

쏅 Press the 5 MIX button

to change among

the playback modes:

Opera-

tion

Display Meaning

CD/

iPod

MIX ALL Mixing tracks

MP3/

WMA

MIX FOLDER

Mixing tracks of

the current folder

MIX ALL

Mixing tracks of

the data carrier

Gen. MIX OFF Regular playback

If the MIX function is switched on, the icon

MIX (mix all tracks) or MIX

(mix tracks of

current folder) is shown on the display.

Repeatedly playing individual tracks

or directories

쏅 Press the 4 RPT button

to change among

the playback modes:

Opera-

tion

Display Meaning

CD/

iPod

REPEAT TRACK

Repeating

tracks

MP3/

WMA

REPEAT TRACK

Repeating

tracks

REPEAT FOLDER

Repeating

folders

Gen. REPEAT OFF

Regular

playback

If the REPEAT function is switched on, the icon

(repeat tracks) or (repeat

folders) is shown on the display.

Con guring the display

쏅 Press the DIS button

once or several times

to toggle between these displays:

Opera-

tion

Display / icon Meaning

TRACK 01 00:15

Track num-

ber and play-

ing time

TRACK 01 03:37

Track

number and

duration

TRACK 01 08:40

Track

number and

time

MP3/

WMA/

iPod

ABCDEF /

File name ²

ABCDEF /

Track name¹

ABCDEF /

Artist¹

ABCDEF /

Album ¹

ABCDEF /

Genre ³

PLAY TIME 00:15

Playing time

TOTAL TIME 03:37

Track dura-

tion

ALL INFO /

All informa-

tion as scroll-

ing text

¹ Track name, artist and album name must be

stored as ID3 tag to be able to display them.

² The  le name is displayed only in MP3/WMA

mode.

³ The genre information is available only on

iPod mode.

Note:

With every track change, the  le name is

brie y shown in MP3/WMA mode and the

track name in iPod mode before the display

switches to the de ned display.

CD/MP3/WMA/iPod mode

Browse mode

In Browse mode, you can directly search for and

select a certain track on the MP3/WMA data carrier

or iPod without interrupting the current playback.

Browse mode in MP3/WMA mode

In MP3/WMA mode, you can select and play a

track from a directory of the data carrier.

쏅 Brie y press the 1LIST button

to call up

the browse mode in MP3/WMA mode.

The display shows the

icon. The

 rst or current folder on the data carrier and

the icon are displayed.

Notes:

• The  rst folder is displayed only if the

browse mode has been called for the  rst

time after inserting or connecting the data

carrier. Afterwards, the current folder is

displayed whenever the browse mode is

called.

• The browse mode remains switched on for

5 minutes without con rming a selection.

• You can exit the browse mode at any time

by pressing the 1LISTbutton

쏅 Turn the rotary control

to select a di er-

ent folder.

쏅 Press the rotary control

to display the

tracks of the selected folder.

The  rst track of the folder and the

icon are

shown on the display.

Note:

To return to the folder list, turn the rotary con-

trol

until the "<<<" option is selected and

press the rotary control

쏅 Turn the rotary control

to select a di er-

ent track.

쏅 Press the rotary control

to play the track.

The playback starts. You are exiting the

browse mode.

Browse mode in iPod mode

In iPod mode, you can select and play the tracks

via the categories "ARTISTS", "ALBUMS", "GENRES"

or "PLAYLISTS".

쏅 Press the 2 ID3 button

to call up the

Browse mode in the iPod mode.

The display shows the

icon. The

 rst category, "ARTISTS", is displayed.

Notes:

• Press the 2 ID3 button

for approx.

2 seconds to directly call up the "PLAYLISTS"

category.

• The browse mode remains switched on for

5 minutes without con rming a selection.

• You can exit the browse mode at any time

by pressing the 2 ID3 button

쏅 Turn the rotary control

to select the

category "ALBUMS" , "GENRES"

or "PLAYLISTS" .

쏅 Press the rotary control

to display the

available folders of the category.

The  rst folder of the selected category is

shown on the display (e.g. "JAZZ" in the

" GENRES" category).

Note:

To return to the list of categories, turn the

rotary control

until the "<<<" option is

selected and press the rotary control

쏅 Turn the rotary control

to select a di er-

ent folder.

쏅 Press the rotary control

to display the

available tracks of the folder.

The  rst track of the folder is shown on the

display.

Note:

To return to the folder list, turn the rotary con-

trol

until the "<<<" option is selected and

press the rotary control

쏅 Turn the rotary control

to select a di er-

ent track.

CD/MP3/WMA/iPod mode | Bluetooth®

쏅 Press the rotary control

to play the track.

The playback starts. You are exiting the

browse mode.

Searching by track names

(not in iPod mode)

On MP3/WMA data carriers, you can  nd a track

based on its  le name and start the playback.

쏅 Press the 1 LIST button

for approx. 2 sec-

onds to start the search function.

You can now enter a  le name with up to

16 characters:

Notes:

• You do not have to enter the complete  le

name. You can enter only the  rst charac-

ters of the  le name and select the desired

track from the list of tracks found.

• You can exit the search function at any

time by brie y pressing the 1 LIST button

쏅 Turn the rotary control

to select a charac-

ter for the respective position.

쏅 Press the rotary control

to go to the next

position.

쏅 Press the 1 LIST button

for approx. 2 sec-

onds to start the search.

All tracks corresponding to the  le name en-

tered are listed.

쏅 If necessary, turn the rotary control

select a track.

쏅 Press the rotary control

to start the play-

back.

Bluetooth®

(Toronto 420 BT only)

You can connect the Toronto 420 BT via Bluetooth®

with other Bluetooth®-ready devices, such as cell

phones or MP3 players. This allows you to use the

car sound system with its integrated microphone

as hands-free system for connected cell phones

and control the audio output of other Bluetooth®

devices and play them back via the loudspeakers

of the car sound system (Bluetooth® streaming).

Note:

You can also connect an external microphone

for hands-free calling (see the chapter "Instal-

lation instructions").

Bluetooth® technology is a wireless connection of

short range. For this reason, Bluetooth® devices

must be located near the car sound system (in the

vehicle) to establish and maintain a connection.

To establish a Bluetooth® connection, you must

 rst pair the car sound system and the Bluetooth®

device. When you pair the devices, a Bluetooth®

connection is subsequently established automati-

cally. This connection remains in e ect as long as

the Bluetooth® device is within range. If the con-

nection is interrupted, e.g. because you moved

the cell phone outside the range, the connection

is automatically re-established as soon as you are

back within range.

You can connect only one cell phone and stream-

ing device with the car sound system at a time.

If you connect a new device with the car sound

system, the connection to a currently connected

device may automatically be interrupted. How-

ever, the car sound system leaves up to 5 di erent

Bluetooth® devices paired, and you can quickly

and easily connect any of these devices with the

car sound system again.

Bluetooth® menu

In the Bluetooth® menu, you  nd all the functions

for pairing, connecting and managing Bluetooth®

devices.

Calling the Bluetooth® menu

쏅 Brie y press the MENU

button to open

the user menu.

쏅 Turn the rotary control

until the "BLUE-

TOOTH" menu item is selected.

쏅 Press the rotary control

to open the Blue-

tooth® menu.

쏅 Turn the rotary control

until the desired

menu item is selected.

쏅 Perform the setting (see the following sec-

tions).

쏅 Brie y press the MENU button

to exit the

menu.

Notes:

• The Bluetooth® menu is automatically ex-

ited approx. 60 seconds after the last but-

ton activation and you are returned to the

display of the current audio source.

• To go back to the next higher-level menu,

turn the rotary control

until the "<<<"

option is selected and press the rotary con-

trol

• If a Bluetooth® process is running (e.g.

re-establishing the connection to the last

connected device), the functions of the

Bluetooth® menu are blocked. If you at-

tempt to open the Bluetooth® menu dur-

ing this time, "LINK BUSY" brie y appears

on the display. If you want to cancel the

Bluetooth® process and open the Blue-

tooth® menu, press the

button

Pairing and connecting a device

Note:

You can pair up to 5 Bluetooth® devices with

this car sound system. Before you can pair a

sixth device, you must  rst unpair one of the

5 already paired devices (see ch. "Additional

functions in the Bluetooth® menu", section

"Managing paired devices").

If you should attempt to pair a sixth Blue-

tooth® device, "PHONE LIST FULL – PLEASE

DELETE ENTRIES FROM LIST" is displayed.

Pairing and connecting a cell phone

Note:

If a connection with a cell phone currently ex-

ists, this connection is automatically discon-

nected if you pair and connect another cell

phone.

쏅 In the Bluetooth® menu, select the "PAIRING"

menu item.

쏅 Press the rotary control

to open the menu.

The "MOBILE PHONE" menu item is selected.

쏅 Press the rotary control

to register a cell

phone.

The display shows "PAIRING" and the Blue-

tooth® symbol

is  ashing. The car sound

system can now be recognised by a Blue-

tooth® cell phone for approx. 2 minutes and

connected.

쏅 Search the car sound system from your cell

phone (Bluetooth® name: "BP 420 BT").

As soon as the car sound system is located

by the cell phone and is to be connected, the

display brie y shows "ENTER PIN" and the cur-

rently stored PIN (by default "1234").

쏅 Establish the connection from your cell

phone. Enter the PIN displayed by the car

sound system.

The display may show "PAIRED", followed by

"CONNECTED", as soon as the car sound sys-

tem and the cell phone are paired and con-

nected.

Notes:

If no connection can be established, the dis-

play brie y shows "CONNECT FAILED".

Pairing and connecting a Bluetooth®

streaming device

Note:

If a connection with a streaming device cur-

rently exists, this connection is automatically

disconnected if you pair and connect another

streaming device.

Bluetooth®

쏅 In the Bluetooth® menu, select the "PAIRING"

menu item.

쏅 Press the rotary control

to open the menu.

The "MOBILE PHONE" menu item is selected.

쏅 Turn the rotary control

to select the

"STREAMING" menu item.

쏅 Press the rotary control

to register a

streaming device.

The display shows the currently stored

PIN (default "1234"). If required, enter the

PIN of the streaming device:

쏅 Turn the rotary control

to select a digit for

the respective position.

쏅 Press the rotary control

to go to the next

position.

Notes:

• To return to the previous position for the

PIN entry, turn the rotary control

until

the "<<<" option is selected, and press the

rotary control

• Not all streaming devices require the entry

of a PIN on the car sound system. For some

streaming devices, you have to enter the

PIN of the car sound system instead. For

these devices, press only the rotary control

repeatedly until you reach beyond the

last position, thereby con rming the cur-

rent PIN, and then enter this PIN on the

streaming device.

The display shows "PAIRING" and the Blue-

tooth® symbol

is  ashing. The car sound sys-

tem can now be recognised by the streaming

device for approx. 2 minutes and connected.

쏅 Search the car sound system from your stream-

ing device (Bluetooth® name: "BP 420 BT") and

establish the connection. Enter the PIN of the

car sound system, if necessary.

The display may show "PAIRED", followed by

"CONNECTED", as soon as the car sound sys-

tem and the streaming device are paired and

connected.

Notes:

• If no connection can be established, the

display brie y shows "CONNECT FAILED".

• After switch-on, the car sound system

automatically attempts to reconnect the

device connected last. If the connection

attempt fails, the display brie y shows

"CONNECTION LOST". If necessary, attempt

to re-establish the connection from the

streaming device.

Telephone functions

Answering/rejecting an incoming phone call

With an incoming call, the display alternately

shows "INCOMING CALL" and the number of the

caller. The current audio source is muted and a

ring tone is played via the loudspeakers of the car

sound system.

Note:

If the number of the caller is not being trans-

mitted, the display shows "PRIVATE NUM-

BER" instead of the number. If the number

of the caller is stored together with a name,

the name of the entry and the number are

displayed (see the section "Storing a phone

number in the car sound system" in this chap-

ter).

쏅 Press the

button

to answer the call.

"CALL" and the duration of the ongoing call

are displayed.

쏅 Press the



button to reject the call or

to end the current call.

The display shows "CALL END".

Notes:

• During the call, you can adjust the volume

with the volume control

or mute the

device with a short press of the On/O

button

• You can adjust the volume for the call play-

back in the user menu (see the chapter

"User settings", section "Making settings in

the "VOLUME" menu", menu item "HANDS-

FREE VOL").

Bluetooth®

Making a call

쏅 In the Bluetooth® menu, select the "DIAL NEW

NUMBER" menu item.

쏅 Press the rotary control

to open the entry

menu.

You can now enter a phone number with up

to 20 digits:

쏅 Turn the rotary control

to select a digit for

the respective position.

쏅 Press the rotary control

to go to the next

position.

Note:

To return to the previous position in the en-

try menu, turn the rotary control

until the

"<<<" option is selected, and press the rotary

control

쏅 Press the

button

to call the number

entered.

"CALLING" and the dialed number are alter-

nately shown on the display.

As soon as your calling party answers the call,

the display shows "CALL" and the time of the

current phone call.

Upon ending the call, the display brie y

shows "CALL END".

Calling an entry in the phone book

Note:

This function is available only if the phone

book of the connected cell phone was trans-

ferred to the car sound system (see the chap-

ter "Phone book functions").

쏅 In the Bluetooth® menu, select the "PHONE-

BOOK" menu item.

쏅 Press the rotary control

to open the phone

book.

The display shows the  rst phone book entry.

Note:

If the phone book has not yet been trans-

ferred, the display brie y shows "PHONE-

BOOK NOT AVAILABLE".

쏅 Turn the rotary control

to select a di er-

ent entry.

쏅 Press the rotary control

or the but-

ton

to call the number.

"CALLING" and the dialed number are alter-

nately shown on the display.

Note:

You can also call an entry in the phone book

via speed dial (see the section "Speed dial for

phone book entries" in this chapter).

Making a call with voice dial

Note:

This function is only available if the connected

cell phone supports voice dial.

쏅 In the Bluetooth® menu, select the "VOICE

DIAL" menu item.

쏅 Press the rotary control

or the but-

ton

to activate voice recognition.

The car sound system is muted and the dis-

play shows "SPEAK NOW".

쏅 Say the name of the desired calling partner.

Notes:

• If no Bluetooth® connection is established

when voice recognition is activated,

the display brie y shows "VOICE DIAL

FAILED – NO BT CONNECTION".

• If the spoken name is not being recognised

or the time for the voice recognition has

already expired, the display brie y shows

"DIAL FAILED".

• You can cancel the voice recognition by

pressing the

button

• Please note that the duration of the voice

recognition is limited and depending on

the respective cell phone.

• You can also activate the voice recognition

via speed dial (see the section "Speed dial

for voice dial" in this chapter).

Bluetooth®

Storing a phone number in the car sound

system

You can store phone numbers in the car sound

system and make calls using the speed dial (see

the following section).

A phone number is stored for the currently con-

nected telephone and is available only for this tel-

ephone. The car sound system can store up to  ve

numbers for up to  ve paired devices.

쏅 Enter the phone number as described in the

section "Making a call".

쏅 Press the desired memory button 1-5

for

approx. 2 seconds to store only the number.

- or -

쏅 Press the rotary control

for approx. 2 sec-

onds to enter a name for the entry.

You can now enter a name with up to 15 char-

acters:

쏅 Turn the rotary control

to select a charac-

ter for the respective position.

쏅 Press the rotary control

to go to the next

position.

Note:

To return to the previous position in the en-

try menu, turn the rotary control

until the

"<<<" option is selected, and press the rotary

control

쏅 Press the desired memory button

1 - 5

for approx. 2 seconds to store the

number and name.

The display brie y shows "NUMBER SAVED".

Afterwards, you are returned to the Blue-

tooth® menu and the "DIAL NEW NUMBER"

menu item.

Notes:

• A number previously stored on the memo-

ry button is replaced.

• If a telephone is unpaired, the numbers

stored for this telephone are automatically

deleted.

Speed dial for any phone number or for the

number dialed last or a stored number

With speed dial, you can make a call without  rst

having to select the corresponding function in the

Bluetooth® menu.

To call the number dialed last,

쏅 press the

button

The display shows the number dialed last.

Note:

If no cell phone is currently connected, the

Bluetooth® menu is opened. The "PAIRING"

menu item is selected.

쏅 Press the

button

to call the number.

"CALLING" and the dialed number are alter-

nately shown on the display.

To call a stored number,

쏅 press the

button

쏅 Press a memory button 1 - 5

to call the

number stored.

Note:

If no number is stored under the selected

memory button, the display brie y shows

"NO NUMBER".

쏅 Press the

button

to call the number.

"CALLING" and the dialed number are alter-

nately shown on the display.

To call any number,

쏅 press the

button

쏅 Press the On/O button

to open the entry

menu and enter a number (enter the phone

number as described in the section "Making

a call").

쏅 Press the

button

to call the number.

"CALLING" and the dialed number are alter-

nately shown on the display.

Bluetooth®

Speed dial for phone book entries

Note:

This function is only available

• if the phone book of the connected cell

phone was transferred to the car sound

system (see the chapter "Phone book func-

tions").

• if the speed dial is set for phone book en-

tries (see the chapter "Additional functions

in the Bluetooth® menu", section "Setting

the button function for speed dial").

To select an entry of the phone book with the

speed dial and call it,

쏅 press the

button

for approx. 2 sec-

onds.

The display shows the  rst phone book entry.

쏅 If necessary, select another entry as described

in the section "Calling an entry in the phone

book".

쏅 Press the button

to call the number.

"CALLING" and the dialed number are alter-

nately shown on the display.

Speed dial for voice dial

Note:

This function is only available

• if the connected cell phone supports voice

dial.

• if the speed dial is set for voice dial (see the

chapter "Additional functions in the Blue-

tooth® menu", section "Setting the button

function for speed dial").

To activate the voice recognition with the speed

dial,

쏅 press the button

for approx. 2 sec-

onds.

The car sound system is muted and the dis-

play shows "SPEAK NOW".

쏅 Say the name of the desired calling partner.

Bluetooth® streaming mode

Starting the Bluetooth® streaming mode

쏅 Press the SRC

button repeatedly until

"BT-STREAM" appears on the display.

The playback starts.

Notes:

• The Bluetooth® streaming mode can be se-

lected only if a suitable streaming device

is connected.

• If the connection to the streaming device

is lost during playback, the display brie y

shows "CONNECTION LOST" and the car

sound system changes to the previous au-

dio source.

Selecting tracks

쏅 Turn rotary control

one notch counter-

clockwise or clockwise to change to the pre-

vious/next track.

Interrupting playback

쏅 Press the 3 button

to interrupt the

playback ("PAUSE") or to continue it.

Phone book functions

Transferring the phone book of the cell phone

to the car sound system

You can transfer the phone book of the connected

cell phone to the car sound system to call entries

of the phone book using the car sound system.

Notes:

• The car sound system accepts only entries

from the memory of the telephone and

not from the SIM card inserted in the tel-

ephone.

• The transfer does not delete the phone

book from the cell phone.

The car sound system can store the phone books

of the paired telephones with a total of up to 960

entries. If several numbers are stored on the tel-

ephone for one contact (e.g. landline, cell phone

number, o ce number and similar), each number

is stored as a separate entry by the car sound sys-

tem.

Bluetooth®

Page is loading ...

Blaupunkt San Francisco 320 Owner's manual

Brand: Blaupunkt

Model: San Francisco 320

Category: Car media receivers

Type: Owner's manual

Download PDF

report

Blaupunkt San Francisco 320 Owner's manual

Blaupunkt San Francisco 320 Owner's manual

Related papers

Other documents