Samsung PS-50P91FD User manual

Register your product at www.samsung.com/global/register

Record your Model and Serial number here for future reference.

▪ Model _______________ ▪ Serial No. _______________

PDP-TELEVISION

(PLASMA DISPLAY PANEL)

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

ON-SCREEN MENUS

Picture In Picture (PIP)

Energy Saving

TELETEXT (Option)

SRS TruSurround XT

Digital Natural Image engine

BN68-01314A-00Eng.indd 1 2007-07-26 ¿ÀÈÄ 11:39:39

English - 2

User Instructions

 Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the

plasma monitor panel for more than 2 hours as it can cause screen image retention. This image

retention is also known as “screen burn”. To avoid such image retention, reduce the degree of

brightness and contrast of the screen when displaying a still image.

 Height

The PDP can normally operate only under 2000m in height. It might abnormally function at a place

over 2000m in height so do not install and operate there.

 Heat on the top of the PDP TV

The top side of the product may be hot after long period of use as heat dissipates from the panel

through the vent hole in the upper part of the product. This is normal and does not indicate any defect

or operation failure of the product. However, children should be prevented from touching the upper

part of the product.

 The product is making a ‘cracking’ noise.

A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding

environment such as temperature or humidity. This is normal and not a defect of the unit.

 Cell Defects

The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require

sophisticated technology to produce. However, there may be few bright or dark pixels on the screen.

These pixels will have no impact on the performance of the product.

 Avoid operating the TV at temperatures below 5°C(41°F)

 A still image displayed too long may cause permanent damage to the PDP Panel.

Watching the PDP TV in 4:3 format for a long period of time may leave traces

of borders displayed on the left, right and centre of the screen caused by the

difference of light emission on the screen. Playing a DVD or a game console

may cause similar effect to the screen. Damages caused by the above effect are

not covered by the Warranty.

 Afterimage on the Screen.

Displaying still images from Video games and PC for longer than a certain period of time may

produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when

displaying still images.

 Warranty

- Warranty does not cover any damage caused by image retention.

- Burn-in is not covered by the warranty.

 Installation

Be sure to contact an authorized service centre, when installing your set in a location with heavy

dust, high or low temperatures, high humidity, chemical substance and where it operates continually

such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.

Any functions related to Digital TV (DVB) will only work in countries or areas where DVB-T (MPEG2)

digital terrestrial signals are broadcasted. Please confirm with your local dealer if you can receive

DVB-T signals. Although this TV set follows the DVB-T specification, maintaining compatibility with

the future coming DVB-T digital terrestrial broadcasts is not guaranteed. Several functions may not be

available in some countries.

BN68-01314A-00Eng.indd 2 2007-07-26 ¿ÀÈÄ 11:39:39

English - 3

Symbols

☛ ➢

Press

Important

Note

Contents

General Information

 User Instructions ............................................. 2

 Checking Parts ................................................ 4

 Using the Stand-Base ..................................... 4

 Control Panel ................................................. 5

 Connection Panel ............................................ 6

 Viewing the Remote Control ........................... 8

Operation

 Switching Your Television On and Off ............. 9

 Plug & Play Feature ...................................... 10

 Viewing the Display ....................................... 11

 Viewing the Menus ........................................ 12

 Using the TOOLS Button .............................. 12

 Viewing External Signal Sources .................. 13

 Editing Device Names ................................... 14

Using the DTV Feature

 Setting the Guide .......................................... 15

 Setting the Default Guide .............................. 15



Checking the Digital-Signal Strength - Digital ..

16

Channel Control

 Storing Channels Automatically .................... 16

 Storing Channels Manually ........................... 17

 Managing Channels ...................................... 18

 Fine Tuning Channel Reception .................... 24

 LNA (Low Noise Ampliﬁer) ............................ 25

Picture Control

 Changing the Picture Standard ..................... 26

 Customizing the Picture Settings .................. 27



Conﬁguring Detailed Settings on the Picture

.. 28

 Selecting the Picture Size ............................. 29

 Digital NR / Active Colour / DNIe .................. 30

 Freezing the Current Picture ......................... 30

 Viewing Picture-in-Picture ............................. 31

Sound Control

 Sound Features ............................................ 33

 Selecting the Sound Mode

(depending on the model) ............................. 34

Function Description

 Setting the Time ............................................ 35

 Menu Transparency / Energy Saving /

HDMI Black Level / Film Mode /

Light Effect(PS50P91FD/PS58P91FD) /

Blue Screen / Melody / Function Help ........... 37

 Activating the Child Lock ............................... 38

 Setting the Subtitle ........................................ 39

 Using the Game Mode .................................. 40

 Setting up the Parental Lock ......................... 41

 Screen Burn Protection ................................. 43

 Wall- mount adjustment (Sold separately)

(PS50P91FD/PS58P91FD) ........................... 44

 Upgrading the Software ................................ 45

 Over the Air Download................................... 46

PC Display

 Setting up Your PC Software

(Based on Windows XP) ............................... 47

 Display Modes .............................................. 48

 Setting the PC ............................................... 49

 Changing the Picture Size (PC Mode) .......... 50

 Setting the Home theatre PC ........................ 50

WISELINK

 Using the WISELINK Function ...................... 51

 Using the WISELINK Mode ........................... 52

 Using the Photo (JPEG) List ......................... 53

 Using the Music (MP3) List ........................... 61

About Anynet

+

 What is Anynet

+

? .......................................... 64

 Connecting Anynet

+

Devices ........................ 64

 Setting Up Anynet

+

....................................... 65

 Scanning and Switching between Anynet

+

Devices ......................................................... 66

 Recording ...................................................... 67

 Listening through a Home theatre ................. 68

 Troubleshooting for Anynet

+

......................... 68

Appendix

 Teletext Feature (depending on the model) .. 69

 Setting Up Your Remote Control ................... 71

 Wall Mount Kit Speciﬁcations (VESA) ........... 76

 How to assemble the Stand-Base

(depending on the model) ............................. 77

 Troubleshooting ............................................ 77

 Speciﬁcations ................................................ 78

BN68-01314A-02Eng.indd 3 2007-08-22 ¿ÀÀü 10:36:21

English - 4

Checking Parts

Owner’s Instructions Remote Control/

AAA Batteries

Power Cord Cloth-Clean

Warranty Card/

Registration Card/

Safety Guide Manual

Cover-Bottom / Screws (2ea)

(Refer to page 77)

Ferrite Core for Power Cord/

Ferrite Core for

Headphones Cable

Sold Separately

S-Video Cable Antenna Cable Component Cables Audio Cables Video Cable

PC Cable PC Audio Cable HDMI Cable HDMI/DVI Cable

➢

Ferrite Core (Power Cord, Headphones Cable)

The ferrite core is used to shield the cable from interference.

When connecting a cable, open the ferrite core and bind cable

round the ferrite core to secure it around the cable.

Using the Stand-Base

➢



Two or more people should carry

the PDP. Never lay the PDP on the

floor because of possible damage

to the screen. Always keep the

PDP upright.



The PDP can rotate 20 degrees in

right and left directions.

-20° ~ 20°

BN68-01314A-01Eng.indd 4 2007-08-17 ¿ÀÈÄ 9:21:15

English - 5

Control Panel

1

SOURCE

Displays a menu of all of the available input

sources (TV, AV1, AV2, S-Video, Component1,

Component2, PC, HDMI1, HDMI2/DVI, and

HDMI3, USB).

➢

In the on-screen menu, use this button as

you would use the ENTER/OK button on

the remote control. (PS50P91FD)

2

MENU

Press to see the on-screen menu of your TV’s

features.

3

+ VOL −

Press to increase or decrease the volume.

In the on-screen menu, use the + VOL −

buttons as you use the ◄ and ► buttons on

the remote control.

4

CH

Press to change channels. In the on-screen

menu, use the CH buttons as you use

the ▲ and ▼ buttons on the remote control.

5

(ENTER)

Press to confirm a selection.(PS63P71FD)

6

(Power) button

Press to turn the TV on and off.

Power Indicator

− Power Off: Blue/Red(PS50P91FD/PS58P91FD)

− Power On: Off

Remote Control Sensor

Aim the remote control towards this spot on

the TV.

7

Speaker

➢

The product colour and shape may vary depending on the model.

Front (or Side) Panel

PS50P91FD/

PS58P91FD

PS63P71FD

BN68-01314A-02Eng.indd 5 2007-08-22 ¿ÀÀü 10:36:29

English - 6

Connection Panel

1

HDMI IN 3

Connect to the HDMI jack of a device with

HDMI output.

2

S-VIDEO or VIDEO / AUDIO L/R

Video (S-Video or Video) and audio inputs for

external devices, such as a camcorder or VCR.

3

Headphones jack

You can connect a set of headphones if you

wish to watch a television programme without

disturbing the other people in the room.

➢

Prolonged use of headphones at a high

volume may damage your hearing.

Continued...

☛



Whenever you connect an audio or video system to your set, ensure that all elements are

switched off.



When connecting an external device, match the colour of the connection terminal to the cable.

➢

The product colour and shape may vary depending on the model.

➢

The product colour and shape may vary depending on the model.

Side Panel

Rear Panel

3

1

2

or

1

4

7

5

2

Cable Television

Network

9

3

8

or

6

BN68-01314A-00Eng.indd 6 2007-07-26 ¿ÀÈÄ 11:39:53

English - 7

9

ANT IN

75Ω Coaxial connector for Aerial/Cable

Network.

Supported modes for HDMI and Component

480i 480p 576i 576p 720p 1080i 1080p

HDMI/

DVI 50Hz

X X X O O O O

HDMI/

DVI 60Hz

X O X X O O O

Component O O O O O O O

BN68-01314A-00Eng.indd 7 2007-07-26 ¿ÀÈÄ 11:39:56

1

POWER IN

Connect the supplied power cord.

2

Connecting external Audio Devices

Connect RCA audio signals from the TV to an

external source, such as Audio equipment.

3

SERVICE

− Connector for service.

− Connect the serial jack between the electro-

motion wall mount bracket and your TV

when you want to adjust the TV viewing

angle using your remote control.

4

VIDEO / AUDIO L/R

Video and audio inputs for external devices,

such as a camcorder or VCR.

5

COMPONENT IN 1, COMPONENT IN 2

Audio (AUDIO L/R) and video (Y/P

B/PR) inputs

for Component.

6

DIGITAL AUDIO OUT (OPTICAL)

Connect to a Digital Audio Component. According

to the received audio signal, optical output is

selectcted by Dobly or PCM signal. The level of

sound can change according to received signal

and sound level's difference can be.

7

PC IN / AUDIO

Connect to the video and audio output jack on

your PC.

8

HDMI IN 1, HDMI IN 2

− Connect to the HDMI jack of a device with

HDMI output. These inputs can also be used

as a DVI connection with separate analog

audio inputs. An optional HDMI/DVI cable

will be necessary to make this connection.

When using the optional HDMI/DVI adapter,

the DVI analog audio inputs on your TV

allow you to receive left and right audio from

your DVI device. (Not compatible with PC)

− When connecting this product via HDMI or

DVI to a Set Top Box, DVD Player or Games

Console etc, make sure that it has been

set to a compatible video output mode as

shown in the table below. Failure to observe

this may result in picture distortion, image

breakup or no picture.

− Do not attempt to connect the HDMI/DVI

connector to a PC or Laptop Graphics Card.

(This will result in a blank screen being

displayed)

DVI IN (HDMI 2) AUDIO L/R

DVI audio outputs for external devices.

The external devices that support lower

version HDMI mode may not implement sound

ouput for theTV with the latest HDMI version

(HDMI 1.3.) In this case, connect to HDMI IN2

and DVI IN (HDMI 2) “ R-AUDIO-L” on the

back panel of the TV.

Part of lower version HDMI cables may cause

annoying flickers or no screen display in this

case use the cable that supports the latest

HDMI version(HDMI 1.3).

English - 8

Viewing the Remote Control

➢



This is a special remote control for the visually impaired persons, and has Braille points on the

Power, Channel, Volume, STOP, and PLAY/PAUSE buttons.



The performance of the remote control may be affected by bright light.

1

POWER button

(turns the TV on and off)

2

Number buttons for direct

channel access

3

One/Two/Three-digit channel

selection

4

Channel control button

5

This function enables you to

view and play photo (JPEG)

and audio files (MP3) from

an external device.

6

Volume increase

Volume decrease

7

Temporary sound switch-off

8

Displays the main on-screen

menu

9

Returns to the previous

menu

@

Picture size selection

#

Electronic Program Guide

(EPG) display

$

Sound mode selection

%

Remote control setup

^

Selects a target device to be

controlled by the Samsung

remote control (TV, DVD,

STB, CABLE, VCR)

&

Press to backlight the VOL,

CH, and the active source

button (TV, DVD, CABLE,

STB, VCR) on the remote.

*

Available source selection

(

Previous channel

)

Press to switch to your

favourite channels.

a

Records for Live

Broadcasting

b

VCR/DVD Function (Rewind,

Stop, Play/Pause, Fast/

Forward)

c

Next channel

Previous channel

d

Exit the on-screen menu

e

Control the cursor in the

menu

f

Use to see information on

the current broadcast

g

TOOLS : Use to quickly

select frequently used

functions.

Anynet

+

: Runs the Anynet

+

view functions and sets up

Anynet

+

devices.

h

Picture-In-Picture On/Off

i

Picture effect selection

j

Digital subtitle display

k

Picture freeze

l

If your remote control is not

functioning properly, take out

the batteries and press the

reset button for about 2~3

seconds.

Reinsert the batteries and

try using the remote control

again.

Teletext Functions

8

Teletext index

9

Exit from the teletext display

(depending on the model)

0

Fastext topic selection

!

Teletext display/mix both

teletext information and the

normal broadcast

@

Teletext size

*

Teletext mode selection

(LIST/FLOF)

(

Teletext sub page

c

P :Teletext next page

P

:Teletext previous page

d

Teletext cancel

f

Teletext reveal

h

Teletext hold

i

Teletext store

BN68-01314A-00Eng.indd 8 2007-07-26 ¿ÀÈÄ 11:39:57

English - 9

Installing Batteries in the Remote Control

1 Lift the cover at the back of the remote control upward as

shown in the figure.

2 Install two AAA size batteries.

➢

 Make sure to match the “+” and “–” ends of the

batteries with the diagram inside the compartment.

 Do not mix battery types, i.e. alkaline and manganese.

3 Close the cover as shown in the figure.

➢

Remove the batteries and store them in a cool and dry

place if you won’t be using the remote control for a long

time. The remote control can be used up to about 23 feet

from the TV. (Assuming typical TV usage, the batteries last

for about one year.)

➢

If the remote control doesn’t work! Check the following:

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power cut, or is the power cord unplugged?

5. Is there a special fluorescent light or a neon sign nearby?

Switching Your Television On and Off

The main lead is attached to the rear of the television.

1 Plug the main lead into an appropriate socket.

➢

The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.

2 Press the (Power) button (On/Off) on the front of the television or press the POWER button on the

remote control to switch the television on. The programme that you were watching last is reselected

automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing

Channels Automatically” on page 16 or “Storing Channels Manually” on page 17.

➢

If the television is initially powered on, several basic customer settings proceed automatically.

Refer to “Plug & Play Feature” on page 10.

3 To switch the television off, press the (Power) button (On/Off) on the front of the television or press

the POWER button on the remote control.

4 To switch the TV on, press the (Power) button (On/Off) on the front of the TV or press the POWER

button or number buttons on the remote control.

BN68-01314A-00Eng.indd 9 2007-07-26 ¿ÀÈÄ 11:40:01

English - 10

Plug & Play Feature

When the TV is initially powered on, basic settings

proceed automatically:

1 Press the POWER button on the remote control.

The message Runs the Plug & Play function when

setting the TV up for the first time or when resetting it.

Sets the channels, the clocks, as well as other

2 The message Select Home Mode when installing this

TV at home. is automatically displayed.

3 Press the ◄ or ► button to select Shop or Home, then

press the ENTER/OK button.

➢

The default selection is Home.

➢

We recommend setting the TV to Home mode for the

best picture in your home environment.

➢

Shop mode is only intended for use in retail

environments.

➢

If the unit is accidentally set to Shop mode, and you

want to return to Dynamic (Home) mode, press the

Volume button and then hold down the

MENU button

for five seconds on the TV panel.

4 The TV will begin memorizing all of the available

channels.

After all the available channels are stored, the Auto

program menu reappears.

Press the ENTER/OK button when channel memorization

is complete.

The Clock Mode menu is displayed.

➢

To stop the search before it has finished, press the

ENTER/OK button with stop selected.

5 Press the ENTER/OK button.

Press the ▲ or ▼ button to select Manual for setting the

current time manually, then press the

ENTER/OK button.

The message Set current date and time. is displayed.

➢

If you select Auto. Select the time zone in which

you live. is displayed, then go to step 8.

6 Press the ◄ or ► button to move to Month, Day, Year,

Hour, Minute or am/pm.Set the date and time you want

bypressing the ▲ or ▼ button, then press the ENTER/OK

button.

➢

You can set the month, day, year, hour, and minute

directly by pressing the number buttons on the

remote control.

7 The message Enjoy your watching. is displayed.

When you have finished, press the ENTER/OK button.

➢

Even if the ENTER/OK button is not pressed, the

message will automatically disappear after several

seconds.

Continued...

Plug & Play

Runs the Plug & Play function when setting the TV up

for the first time or when resetting it. Sets the

channels,clocks, as well as other functions.

Enter

OK

Plug & Play

Select Home Mode when installing this TV at home.

Home

Shop

SkipEnter

Move

Plug & Play

Auto Store is completed.

3 channels are memorized.

Digital:1 Analog:2

OK

SkipEnter

Plug & Play

Set the Clock Mode.

Clock Mode : Auto 

SkipEnter

Plug & Play

Set the Clock Mode.

Clock Mode : Auto

Auto

Manual

Move

Plug & Play

Set current date and time

0 1

Month

0 1

Day

2 0 0 7

Year

0 0

Hour

0 4

Minute

Enter

Skip

Move

Adjust

a m

am/pm

Plug & Play

Auto Store in Progress.

Stop

Digital Channel found: 0

3%

SkipEnter

Digital Channels are added on the favourite

channel list.

6

Plug & Play

Press Enter to start channel memory.

Start

0%

SkipEnterf

BN68-01314A-02Eng.indd 10 2007-08-22 ¿ÀÀü 10:36:42

functions.is automatically displayed.

Return

English - 11

Setting the Clock Automatically

8 Press the ENTER/OK button.

Press the ▲ or ▼ button to select Off or On, then the

ENTER/OK button.

The message Select the time zone in which you live.

is displayed.

9 Press the ▲ or ▼ button to highlight the time zone

for your local area (and to move the highlight to the

appropriate time zone on the map of the United States).

Press the ENTER/OK button.

If clock is not automatically set, see pages 35~36. to set

the clock.

10 The message Enjoy your watching. is displayed.

When you have finished, press the ENTER/OK button.

➢

Even if the ENTER/OK button is not pressed, the

message will automatically disappear after several

seconds.

Viewing the Display

The display identifies the current channel and the status of

certain audio-video settings.

Press the INFO button on the remote control.

Plug & Play

Enjoy your watching.

OK

ATV

3

No Time Information

Plug & Play

Select the time zone in which you live.

SkipEnter

New South Wales/ACT

Victoria

QueenSland

South Australia

West Australia

Tasmania



Move

BN68-01314A-02Eng.indd 11 2007-08-22 ¿ÀÀü 10:36:43

English - 12

Viewing the Menus

1 With the power on, press the MENU button.

The main menu will appear at the bottom of the screen.

There are seven menu groups: Picture, Sound, Channel,

Setup, Input, Guide, and PIP.

2 Press the ▲ or ▼ button, then press the ENTER/OK

button to select an item you want in the menu. Press the

▲/▼/◄/►/ENTER/OK button to display, change, or use

the selected items.

3 Press the EXIT button to exit.

Using the TOOLS Button

The Tools button allows you to display frequently used Menu

and Connection items with a Single button press.

1 Press the TOOLS button.

The TOOLS menu will appear.

2 Press the ▲/▼ button to select a menu, then press the

ENTER/OK button.

3 Press the ▲/▼/◄/►/ENTER/OK buttons to display, change,

or use the selected items.

For a more detailed description of each function, refer to the

corresponding page.

 Device List, see page 63

Picture Setting, see page 27

Sound Setting, see page 33

Sleep Timer, see page 36

Delete Favourite Channel, see page 20

Auto Store, see page 16

Mode

:

Dynamic

Contrast : 100

Brightness : 45

Sharpness : 75

Colour : 55

Tint (G/R) : G50/R50

Colour Tone : Cool1

Detailed Settings

Picture

Device List

Picture Size : 16:9

Picture Mode : Dynamic

Sound Mode : Standard

Sleep Timer : Off

Delete from Favourite

Auto Store

Move

Enter

TOOLS

BN68-01314A-00Eng.indd 12 2007-07-26 ¿ÀÈÄ 11:40:03

English - 13

Viewing External Signal Sources

You can switch between viewing signals from connected

equipment, such as a VCR, DVD, Set-Top Box, and the TV

source (broadcast or cable).

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Input, then press the

ENTER/OK button.

3 Press the ENTER/OK button again to select Source List.

4 Press the ▲ or ▼ button to select the signal source, then

press the ENTER/OK button.

Available signal sources:

TV, AV1, AV2, S-Video,

Component1, Component2, PC, HDMI1, HDMI2/DVI,

HDMI3, USB

➢

You can select these options simply by pressing the SOURCE

button on the remote control.

Source List

Edit Name

Input

TV

AV1

----

AV2

----

S-Video

----

Component1

----

Component2

----

PC

----



Refresh Option

BN68-01314A-00Eng.indd 13 2007-07-26 ¿ÀÈÄ 11:40:04

English - 14

Editing Device Names

You can give a name to the external source.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Input, then press the

ENTER/OK button.

3 Press the ▲ or ▼ button to select Edit Name, then press

the ENTER/OK button.

4 Press the ▲ or ▼ button to select the external source to

be edited, then press the ENTER/OK button.

5 Select the required device by pressing ▲ or ▼, then press

the ENTER/OK button.

Available device names:

VCR, DVD, D-VHS, Cable STB,

HD STB, Satellite STB, PVR STB, AV Receiver, DVD

Receiver, Game, Camcorder, DVD Combo, DVD HDD

Recorder, PC, Internet TV Recv., Interactive TV Recv.,

VOD STB, TV.

6 Press the EXIT button to exit.

➢

When a PC with a resolution of 1920 x 1080@60Hz

is connected to the HDMI IN 1 port, you should set

the HDMI1 mode to PC in the Source List of the

Input mode. If the HDMI1 mode is not PC, it works

depending on the TV setting.

Input

Source List

Edit Name 

Edit Name

AV1 :

----



AV2 :

----

S-Video :

----

Component1 :

----

Component2 :

----

PC :

----

HDMI1 :

----



Enter

Return

Move

Edit Name

AV1 :

----

AV2 :

----

S-Video :

----

Component1 :

----

Component2 :

----

PC :

----

HDMI1 :

----



----

VCR

DVD

D-VHS

Cable STB

HD STB

Enter Return

Move

BN68-01314A-00Eng.indd 14 2007-07-26 ¿ÀÈÄ 11:40:05

English - 15

Setting the Guide

You can set the guide as your preference.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼button to select Guide. Press the

ENTER/OK button.

3 Select your required guide (Now & Next Guide or Full

Guide) by pressing the ▲ or ▼ button.

4 Press the ENTER/OK button.

5 Select a programme of your choice by pressing the ▲, ▼,

◄, or ► button.

6 Press the INFO button to display information about the

highlighted programme.

7 Press the red button to exchange Now & Next Guide or

Full Guide.

8 Press the EXIT button or blue button to exit.

Setting the Default Guide

You can preset the default guide style.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼button to select Guide. Press the

ENTER/OK button.

3 Press the ▲ or ▼ button to select Default Guide, then

press the ENTER/OK button.

4 Select Now/Next or Full Guide using the ▲ or ▼ button,

and press the ENTER/OK button.

5 Press the EXIT button to exit.

➢

You can select these options by simply pressing the

GUIDE button on the remote control.

WISELINK

Full Guide

Now&Next Guide

Default Guide : Full Guide

Guide

Full Guide

Now&Next Guide

Default Guide : Now&Next

Guide

Now&Next

Full Guide

AM6:00-AM7:00 AM7:00-AM8:00

Watch

INFO

Info



Now&Next



-2Hours



+2Hours



Exit

Today

DTV 77 Digital

NBC TODAY

AM 4:00 - AM 6:00

International news and weather. Including interviews with ne..

77 Digital

7 Digital

7 HD Digital

7 Digital 1

7 Digital 2

7 Digital 3

7 Guide

SUNRISE

NBC TODAY

BN68-01314A-00Eng.indd 15 2007-07-26 ¿ÀÈÄ 11:40:06

English - 16

Storing Channels Automatically

You can scan for the frequency ranges available to you

(availability depends on your country).

Automatically allocated programme numbers may not

correspond to actual or desired programme numbers.

However you can sort numbers manually and clear any

channels you do not wish to watch.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER/OK button.

3 Press the ▲ or ▼ button to select Auto Store, then press

the ENTER/OK button.

4 Press the ENTER/OK button again to start the search.

The search will end automatically.

➢

To stop the search before it has finished, press the MENU or the ENTER/OK button.

Checking the Digital-Signal Strength - Digital

Unlike analog channels, which can vary in reception quality

from “snowy” to clear, digital (HDTV) channels have either

perfect reception quality or you will not receive them at all.

So, unlike analog channels, you cannot fine tune a digital

channel.

You can, however, adjust your antenna to improve the

reception of available digital channels.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER/OK button.

3 Press the ▲ or ▼ button to select Signal Strength, then

press the ENTER/OK button.

4 If the signal strength meter indicates that the signal is

weak, physically adjust your antenna to increase the

signal strength.

Continue to adjust the antenna until you find the best

position with the strongest signal.

5 Press the EXIT button to exit.

Channel

Manual Store

Fine Tune

Signal Strength 

LNA : On

Signal Strength

OK

Enter

Return

Channel

Channel List

Auto Store 

Manual Store

Fine Tune

Signal Strength

LNA : On

BN68-01314A-00Eng.indd 16 2007-07-26 ¿ÀÈÄ 11:40:07

English - 17

Storing Channels Manually

You can store television channels, including those

received via cable networks.

When storing channels manually, you can choose:

 Whether or not to store each of the channels found.

 The programme number of each stored channel which you

wish to identify.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press

the ENTER/OK button.

3 Press the ▲ or ▼ button to select Manual Store, then

press the ENTER/OK button.

4 Select the required option by pressing the ▲ or ▼ button,

then press the ENTER/OK button.

➢

On digital mode, you can choose Digital Channel, on

analog mode ,you can choose Digital Channel and

Analog Channel.

5 When you are satisfied with your setting, press the

ENTER/OK button.

6 Press the EXIT button to exit.

 Programme (Programme number to be assigned to a

channel)

− Press the ▲ or ▼ button until you find the correct

number.

➢

You can also select the channel number directly by

pressing the numeric buttons (0~9).

 Colour System: Auto/PAL

− Press the ▲ or ▼ button to select the required colour

standard.

 Sound System: DK/I/BG

− Press the ▲ or ▼ button to select the required sound

standard.

 Channel (When you know the number of the channel to

be stored)

− Press the ▲ or ▼ button to select

C (Air channel) or S

(Cable channel).

− Press the ► button, then press the ▲ or ▼ button to

select the required number.

➢

You can also select the channel number directly by

pressing the numeric buttons (0~9).

➢

If there is abnormal sound or no sound, reselect the

sound standard required.

 Search (When you do not know the channel numbers)

− Press the ▲ or ▼ button to start the search.

− The tuner scans the frequency range until the first channel or the channel that you selected is

received on the screen.

 Store (When you store the channel and associated programme number)

− Set to

OK by pressing the ENTER/OK button.

☛

Channel mode

 P (Programme mode): When completing tuning, the broadcasting stations in your area have

been assigned to position numbers from P00 to P99. You can select a channel by entering the

position number in this mode.

 C (Air channel mode): You can select a channel by entering the assigned number to each air

broadcasting station in this mode.

 S (Cable channel mode): You can select a channel by entering the assigned number for each

cable channel in this mode.

Channel

Channel List

Auto Store

Manual Store 

Fine Tune

Signal Strength

LNA : On

Channel

Channel List

Auto Store

Manual Store : On 

Fine Tune

Signal Strength

LNA : On

Digital Channel

Analog Channel

Manual Store

4 3

Channel

6 3 4 5 0 0 K H z

Frequency

7 M H z

Bandwidth

Return

Enter

Adjust

Move

Start

Manual Store

1

Programme

A u t o

Colour System

B G

Sound System

Return

Enter

Adjust

Move

Channel

6 2 M H z

Search

?

Store

C 2

BN68-01314A-00Eng.indd 17 2007-07-26 ¿ÀÈÄ 11:40:07

English - 18

Managing Channels

Using this menu, you can Add/Delete or set Favourite

channels and use the program guide for digital broadcasts.

Viewing All Channels

Show all currently available channels.

To use the Channel List function, first run Auto Program.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER/OK button.

3 Press the ▲ or ▼ button to select Channel List, then

press the ENTER/OK button.

4 Press the ◄ button to select Added Channels.

5 Press the ▲ or ▼ button to select All Channels, then

press the ENTER/OK button.

Shows all currently available channels.

6 Press the ▲ or ▼ button to select a channel to view, then

press the ENTER/OK button.

You can watch the selected channel.

➢

You can press Number buttons on Remote control for

direct channel access,press the same Number button

again to switch between digital channel and ATV channel.

➢

You can select these options simply by pressing the CH LIST

button on the remote control.

Using the Colour buttons on the Remote with the Channel List

 Green (Zoom): Enlarges or shrinks a channel number.

 Yellow (Select): Selects multiple channel lists.

 Blue (Option): Displays the Add (or Delete), Add Favourite (or Delete Favourite), Timer Viewing, and

Channel Name Edit menus.

➢

A gray-coloured channel refers to a deleted channel. The Add menu only appears for deleted

channels.

➢

If you select multiple channel include “favourite

channels”,“delete channel etc. channels”and other

channels, you can choose “Add to Favourite or Delete from

Favourite or Add or Deselect All”etc.

Continued...

Channel

Channel List 

Auto Store

Manual Store

Fine Tune

Signal Strength

LNA : On

1 ♥ 7HD Digital

2 ♥ 7Digital 1

3 ♥ 7Digital 2

4 ♥ 7Digital 3

ATV0 C1

ATV1 C2

ATV2 C3

ATV3 C4

ATV4 C5

Added Channels



Zoom



Select



Option

BN68-01314A-00Eng.indd 18 2007-07-21 ¿ÀÈÄ 12:57:49

1 ♥ 7HD Digital

2 ♥ 7Digital 1

3 ♥ 7Digital 2

4 ♥ 7Digital 3

ATV0 C1

ATV1 C2

ATV2 C3

ATV3 C4

ATV4 C5

All Channels



Zoom



Select



Option

1 ♥ 7HD Digital

2 7Digital 1

3 ♥ 7Digital 2

4 ♥ 7Digital 3

ATV0 C1

ATV1 C2

ATV2 C3

ATV3 C4

ATV4 C5

Add

Delete

Add to Favourite

Delete from Favourite

Deselect All

All Channels



Zoom



Select



Option

English - 19

Adding and Erasing Channels

You can add or delete a channel to display the channels you want.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER/OK button.

3 Press the ▲ or ▼ button to select Channel List, then

press the ENTER/OK button.

4 Press the ◄ button to select Added Channels.

5 Press the ▲ or ▼ button to select All Channels, then

press the ENTER/OK button.

Shows all currently available channels.

6 Press the ▲ or ▼ button to select a channel to add, then

press the blue button.

7 Press the ENTER/OK button to select Add.

➢

All added channels will be shown on Added

Channels menu.

8 Press the ▲ or ▼ button to select a channel to delete,

then press the blue button.

Press the ENTER/OK button to select Delete.

9 Press the EXIT button to exit.

➢

You can also delete a channel in the Added Channels

menu in the same manner.

➢

You can select these options simply by pressing the CH LIST

button on the remote control.

Continued...

Channel

Channel List 

Auto Store

Manual Store

Fine Tune

Signal Strength

LNA : On

BN68-01314A-00Eng.indd 19 2007-07-26 ¿ÀÈÄ 11:40:10

1 ♥ 7HD Digital

2 ♥ 7Digital 1

3 ♥ 7Digital 2

4 ♥ 7Digital 3

ATV0 C1

ATV1 C2

ATV2 C3

ATV3 C4

ATV4 C5

All Channels



Zoom



Select



Option

1 ♥ 7HD Digital

2 ♥ 7Digital 1

3 ♥ 7Digital 2

4 ♥ 7Digital 3

ATV0 C1

ATV1 C2

ATV2 C3

ATV3 C4

ATV4 C5

Delete

Delete from Favourite

Timer Viewing

Channel Name Edit

All Channels



Zoom



Select



Option

English - 20

Channel

Channel List 

Auto Store

Manual Store

Fine Tune

Signal Strength

LNA : On

1 ♥ 7HD Digital

2 ♥ 7Digital 1

3 ♥ 7Digital 2

4 ♥ 7Digital 3

ATV0 C1

ATV1 C2

ATV2 C3

ATV3 C4

ATV4 C5

Added Channels



Zoom



Select



Option

1 ♥ 7HD Digital

2 ♥ 7Digital 1

3 ♥ 7Digital 2

4 ♥ 7Digital 3

ATV0 C1

ATV1 C2

ATV2 C3

ATV3 C4

ATV4 C5

Added Channels



Zoom



Select



Option

Delete

Delete from Favourite

Timer Viewing

Channel Name Edit

Device List

Picture Size : 16:9

Picture Mode : Dynamic

Sound Mode : Standard

Sleep Timer : Off

Delete from Favourite

Auto Store

Move

Enter

TOOLS

BN68-01314A-00Eng.indd 20 2007-07-26 ¿ÀÈÄ 11:40:12

Setting Your Favourite Channels

You can set channels you watch frequently as favourites.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press

the ENTER/OK button.

3 Press the ▲ or ▼ button to select Channel List, then

press the ENTER/OK button.

4 Press the button to select Added Channels.

5 Press the button to select Favourite,then press the

ENTER/OK button. You can view all favourite channels.

6 Press the button to select Added Channels,

then press the ENTER/OK Button.

7 Press the ▲ or ▼ button to select a channel as a favourite

channel, then press the blue button.

8 Press the ▲ or ▼ button to select

Add to Favourite, then

press the ENTER/OK button.

The “♥” symbol will be displayed and the channel will be

set as a favourite.

9 To cancel your favourite channel selection, press the blue

button when a favourite channel is selected. Press the ▲

or ▼ button to select

Delete from Favourite, then press

the ENTER/OK button. The channel is deleted from

Favourites and the “♥” mark also disappears.

10 Press the EXIT button to exit.

➢

You can also Add or Delete a channel from Favourites in

the All Channels menu in the same manner.

➢

Only memorized channels can be set as favourite

channels.

➢

All favourite channels will be shown on Favourite menu.

➢

You can select these options simply by pressing the CH

LIST button on the remote control.

Easy Setting

1 Press the TOOLS button on the remote control.

2 Press the ▲/▼ button to select

Add to Favourite or

Delete from Favourite

, then press the ENTER/OK

button. The current channel is added to or deleted from

Favourites.

➢

To select the favourite channels you have set up, press the

FAV.CH

button on the remote control.

Continued...

▲ or ▼

◄

Page is loading ...

Samsung PS-50P91FD User manual

This manual is also suitable for

Samsung PS-50P91FD User manual

Related papers

Other documents