Swann 3-Feb User manual
- Category
- Security device components
- Type
- User manual
This manual is also suitable for
B
Connecting the receiver to record on a VCR
LINE IN
LINE OUT
VIDEO
AUDIO
VCR
TV
Video
INPUTS Video
OUTPUT
1
3
Component
INPUTS
1 2
RECEIVER
Connect the A/V cable
from the receiver to
the VCR
D.
Plug the power supply
into the receiver
B.
C.
Connect an A/V cable
from the Line OUTPUT
on the back of the VCR
Connect the A/V cable
to the INPUT on the
back of the TV
D
Viewing the cameras and recording to VCR
Power on the Receiver,
VCR and TV
Using your TV’s remote
control tune your TV to
the correct INPUT*. In our
example above the TV
should be set to INPUT 1
Using your VCR’s remote
control tune your VCR to
the LINE 1 INPUT*
You should now see
your cameras on the
TV screen. Follow
your manufacturer’s
instructions to
record to your VCR
1.
2. 3. 4.
*Some VCR’s and TV’s will list this as INPUT, A/V, SOURCE, L1, Channel 0 - Consult your manufacturer’s manual for more information
1. Connect the AV cable to the back of the Receiver
2. Connect the AV cable to an available Video INPUT on TV
3. Tune TV to the correct INPUT* using TV remote
Connecting the receiver to your TV
Back of TV
Back of Receiver
C
13
INPUTS
Package Contents
A
2 or 3 NightHawk
Cameras
Packaging
Receiver
Remote Control
Hardware
AV Cable
Quick Start Manual
Camera Power
Supplies
Receiver Power
Supply
Nighthawk 2/3 Camera Kit Easy Setup Guide
www.swannsecurity.com6ZDQQ&RPPXQLFDWLRQV7ROO)UHH7HFKQLFDO6XSSRUW86$1 877 274 3695$XVWUDOLD1300 13 8324(PDLO[email protected]
H
General Installation Notes and Tips
1. Test the camera signal before permanently installing the cameras.
2. Using battery power is only recommended for testing purposes as the cameras do require constant power to operate.
3. IR or night vision will reflect off of glass or windows and overexpose the picture. Try placing cameras in direct line of
sight of your subject.
4. Never aim the camera directly at the sun as this can permanently damage the lens.
5. Never submerge the camera in water. Some shelter is recommended such as an awning or eave.
Camera Positioning
Achieving the highest quality signal
G
G
FE
Wireless Internet
Cordless Phones/Mobiles
Some Electronic Devices
If you are still receiving interference change the
camera’s channel as per step E then switch the
receiver to the correct channel
If possible turn off or keep
the camera and receiver
away from wireless devices
Some wireless devices can
be set to different frequencies.
Consult the manufacturer’s
manual for details
A clear line of sight with little wireless
interference will always give you the
strongest picture
Walls and floors can also limit range and image results. Place the receiver in a location that
is relatively close to the camera’s position
Setting the Camera Channel
1.
Find the seam running
around the middle of
the camera
2. Twist the front half of the
camera counter-clockwise
to remove the outer casing
3.
Locate the small white
dip switches in the
upper left region of
the camera
4. Using your fingernail or pen,
move the dip switches up
or down to change to the
appropriate channel
Channel and Frequency Settings
Channel 1
2414MHz
Channel 2
2432MHz
Channel 4
2468MHz
Channel 3
2450MHz
1
2
1
2
1
2
1
2
Note: Wireless and electronic devices such as these can interfere with camera
transmission if they are within the cameras range.
Note: If your camera
has a hood, remove
the 2 screws first
Nighthawk 2/3 Camera Kit Easy Setup Guide
www.swannsecurity.com6ZDQQ&RPPXQLFDWLRQV7ROO)UHH7HFKQLFDO6XSSRUW86$1 877 274 3695, Australia - 1300 13 8324(PDLO[email protected]
-
1
-
2
Swann 3-Feb User manual
- Category
- Security device components
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Swann Nighthawk 2 Easy Setup Manual
-
-
Swann Night Hawk SW231-WOC User manual
-
-
Swann SW211-STY Installation guide
-
-
-
-
-
