AT&T CL82351 User manual

Complete user’s manual

CL82101/CL82201/CL82251/

CL82301/CL82351/CL82401/

CL82451/CL82501/CL82551/

CL82601

DECT 6.0 cordless telephone/

answering system with

caller ID/call waiting

Congratulations

on your purchase of this AT&T product. Before using this AT&T product,

please read the Important safety information section on pages 74-75

of this manual. Please thoroughly read this user’s manual for all the

feature operations and troubleshooting information necessary to install

and operate your new AT&T product. You can also visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

This telephone meets the California Energy Commission regulations for

energy consumption. Your telephone is set up to comply with the energy-

conserving standards right out of the box. No further action is necessary.

This telephone system is compatible with certain AT&T DECT 6.0 cordless

headsets. Visit www.telephones.att.com/headsets for a list of

compatible cordless headsets.

Model number: CL82101 (one handset)

CL82201/CL82251 (two handsets)

CL82301/CL82351 (three handsets)

CL82401/CL82451 (four handsets)

CL82501/CL82551 (five handsets)

CL82601 (six handsets)

Type: DECT 6.0 cordless telephone/answering system with

caller ID/call waiting

Serial number: __________________________________________________________

Purchase date: __________________________________________________________

Place of purchase: _______________________________________________________________

Both the model and serial numbers of your AT&T product can be found on

the bottom of the telephone base.

Save your sales receipt and original packaging in case it is necessary to

return your telephone for warranty service.

T

Compatible with

Hearing Aid T-Coil

TIA-1083

Telephones identified with this logo have reduced noise and interference

when used with most T-coil equipped hearing aids and cochlear implants. The

TIA-1083 Compliant Logo is a trademark of the Telecommunications Industry

Association. Used under license.

the AT&T logo are trademarks of AT&T Intellectual Property licensed to

Advanced American Telephones, San Antonio, TX 78219. Printed in China.

The ENERGY STAR® program (www.energystar.gov) recognizes and encourages

the use of products that save energy and help protect our environment. We

are proud to mark this product with the ENERGY STAR® label indicating it

meets the latest energy efficiency guidelines.

Parts checklist

Your telephone package contains the following items. Save your sales receipt

and original packaging in the event warranty service is necessary.

Battery for cordless handset

(1 for CL82101)

(2 for CL82201/CL82251)

(3 for CL82301/CL82351)

(4 for CL82401/CL82451)

(5 for CL82501/CL82551)

(6 for CL82601)

Cordless handset

(1 for CL82101)

(2 for CL82201/CL82251)

(3 for CL82301/CL82351)

(4 for CL82401/CL82451)

(5 for CL82501/CL82551)

(6 for CL82601)

Charger for cordless handset

with power adapter installed

(1 for CL82201/CL82251)

(2 for CL82301/CL82351)

(3 for CL82401/CL82451)

(4 for CL82501/CL82551)

(5 for CL82601)

Battery compartment cover

(1 for CL82101)

(2 for CL82201/CL82251)

(3 for CL82301/CL82351)

(4 for CL82401/CL82451)

(5 for CL82501/CL82551)

(6 for CL82601)

Abridged

user’s manual

Telephone base

Telephone line cord

Power adapter for

telephone base

Wall mount bracket

BY

1021

BT183342/BT283342

2.4V 400mAh Ni-M

H

Abridged user’s manual

CL82101/CL82201/CL82251/

CL82301/CL82351/CL82401/

CL82451/CL82501/CL82551/

CL82601

DECT 6.0 cordless telephone/

answering system with

caller ID/call waiting

Quick start guide

Telephone base installation

If you have

DSL high-speed

Internet service,

a DSL filter (not

included) is

required.

This qu ick star t guide provides you w ith bas ic instructions

only. For mo re complete instruc tions, refer to yo ur Abri dged

user’s manual provided in the package, or s ee the online

Complete user’s manual at www.telep hones.com/manu als.

Plug the power

adapter into an

electrical outlet not

controlled by a wall

switch.

Charger installation

Quick start guide

CL82101/CL82251/CL82201/CL82301/CL82351/CL82401/

CL82451/CL82501/CL82551/CL82601

Plug the power cord

and telephone line

cord into the jacks.

Route the

cords through

the slot.

Plug the other end of

the telephone line cord

into a telephone jack or

a DSL filter.

Raise the

antenna.

Caution: Use only the power adapter provided with this product. To obtain a replacement, visit

our website at www.telephones.att.com or call 1 (800) 222-3111.

Complete user’s manual

CL82101/CL82201/CL82251/

CL82301/CL82351/CL82401/

CL82451/CL82501/CL82551/

CL82601

DECT 6.0 cordless telephone/

answering system with

caller ID/call waiting

Table of contents

Getting started

Quick reference guide - handset ........1

Quick reference guide - telephone

base .............................................................3

Installation ..................................................... 4

Telephone base and charger

installation ...............................................5

Telephone base installation ............5

Charger installation .............................5

Battery installation and charging ....... 6

Installation options .................................... 8

Tabletop to wall mount

installation.............................................8

Wall mount to tabletop

installation.............................................9

Telephone settings

Handset settings ...................................... 10

Ringer volume ..................................... 11

Ringer tone ........................................... 11

Set date/time ...................................... 12

LCD language ...................................... 13

Caller ID announce ........................... 13

Handset settings ...................................... 14

Set speed dial voicemail

number ................................................. 14

Voicemail (visual message

waiting) indicator ............................ 15

Clear voicemail indicator ............... 15

Rename handset ................................ 16

Key tone ................................................. 16

Use caller ID to automatically

set date and time ........................... 17

Home area code ................................. 17

Dial mode .............................................. 18

Website ................................................... 18

Telephone operation

Handset operation .................................. 19

Making a call ........................................ 19

On hook dialing (predialing) ........ 19

Answering a call ................................ 19

Ending a call ........................................ 19

Auto off .................................................. 19

Temporary ringer silencing ........... 19

Speakerphone ..................................... 20

Last number redial ............................ 20

Equalizer ................................................. 21

Options while on calls .......................... 22

Volume control ................................... 22

Call waiting ........................................... 22

Mute ......................................................... 22

Chain dialing ........................................ 23

Temporary tone dialing .................. 24

Blind transfer ....................................... 24

Multiple handset use

Multiple handset use ............................. 25

Handset locator .................................. 25

Join a call in progress ..................... 25

Intercom ....................................................... 26

Answer an incoming call during

an intercom call .............................. 26

Call transfer using intercom .............. 27

Push-to-talk (PTT) ................................... 28

Turn PTT on or off ............................. 28

PTT call to a single handset ........ 28

PTT call to a group of handsets ... 29

Answer a PTT call .............................. 30

Change a one-to-one PTT call

to an intercom call ........................ 30

Answer an incoming call during

PTT ......................................................... 31

Make an outgoing call during

PTT ......................................................... 31

End or leave a PTT call ................... 31

Directory

About the directory ................................ 32

Shared directory ................................. 32

Capacity .................................................. 32

Create directory entries ....................... 33

Create a new directory entry ...... 33

Add a predialed telephone

number to the directory .............. 34

Review the directory .............................. 35

Review directory entries ................ 35

Search by name.................................. 35

Dial, delete or edit directory

entries ..................................................... 36

Display dial ........................................... 36

Delete a directory entry ................. 36

Edit a directory entry ....................... 36

Speed dial .................................................. 37

Assign a speed dial number......... 37

Reassign a speed dial number .... 37

Delete a speed dial number......... 38

Assign your speed dial

voicemail number ........................... 38

Make a call using speed dial ....... 38

Check your voicemail using

speed dial ........................................... 38

About caller ID ......................................... 39

Information about caller ID

with call waiting .............................. 39

Caller ID history ....................................... 40

How the caller ID history

(caller ID log) works ...................... 40

Missed (new) call indicator ........... 40

Caller ID operation ................................. 41

Memory match .................................... 41

Review the caller ID history ......... 41

View dialing options ......................... 42

Dial a caller ID log entry ............... 42

Delete caller ID log entries .......... 42

Save a caller ID log entry to

the directory ...................................... 43

Reasons for missing caller ID

information ........................................... 44

Answering system

Answering system settings ................. 45

Announcement ................................... 45

Answer on/off ..................................... 46

Call screening ...................................... 47

Number of rings ................................. 47

Remote access code ........................ 48

Message alert tone ........................... 49

Message recording time ................. 49

About the answering system............. 50

Answering system and voicemail

indicators ............................................ 50

Using the answering machine

and voicemail together ................ 50

Message capacity .............................. 51

Voice prompts ..................................... 51

Call screening at the telephone

base ....................................................... 51

Call screening at the handset ..... 52

Call intercept ....................................... 52

Base ringer ........................................... 52

Temporarily turning off the

message alert tone ........................ 52

Message playback ................................... 53

Options during playback ................ 53

Delete all old messages ................. 54

Recording and playing memos ......... 55

Record a memo .................................. 55

Play back a memo ............................ 55

Base message counter displays ....... 56

Message counter displays ............. 56

Remote access .......................................... 57

Appendix

Adding and registering handsets/

headsets ................................................. 59

Register a handset to your

telephone base ................................ 59

Deregistering handsets ........................ 60

Deregister all handsets from

your telephone base ..................... 60

Alert tones and lights ........................... 61

Screen icons ......................................... 61

Handset alert tones .......................... 61

Telephone base tones ..................... 61

Lights ....................................................... 62

Handset display screen messages ....63

Screen display messages ............... 63

Troubleshooting ....................................... 65

Maintenance............................................... 73

Important safety information ............ 74

Safety information ............................. 74

Especially about cordless

telephones ......................................... 75

Precautions for users of

implanted cardiac

pacemakers ........................................ 75

Pacemaker patients .......................... 75

Especially about telephone

answering systems ......................... 75

FCC Part 68 and ACTA.......................... 76

FCC Part 15 ................................................ 78

California Energy Commission

battery charging testing

instructions ........................................... 79

Limited warranty ...................................... 80

Technical specifications ....................... 82

DECT 6.0 digital technology ......... 82

Telephone operating range .......... 82

Redefining long range coverage

and clarity .......................................... 82

HD audio ................................................ 82

Index

Index .............................................................. 83

1

CHARGE indicator

On when the handset is

charging in the telephone base

or charger.

qCID/VOLUME

Press qCID to show caller ID

history (page 41).

Press to scroll down while

in menus.

While entering names or

numbers, press to move the

cursor to the left.

Press to decrease the listening

volume when on a call (page 22),

or to decrease the message

playback volume (page 53).

PHONE/FLASH

Press to make or answer a call.

During a call, press to answer

an incoming call when you

receive a call waiting alert

(page 22).

1

While reviewing a caller ID

log entry, press repeatedly to

add or remove 1 in front of

the telephone number before

dialing or saving it in the

directory (page 42).

Press and hold to set (page 14)

or dial your voicemail number

(page 38).

MUTE/DELETE

During a call, press to mute the

microphone (page 22).

While reviewing the caller ID

history, the directory or the redial

memory, press to delete an

individual entry (page 42, page 36

and page 20, respectively).

While predialing, press to delete

digits (page 19).

/SPEA�ERSPEA�ER

Press to switch between

the speakerphone and the

handset (page 20).

Quick reference guide - handset

# (pound key)

Press repeatedly to display

other dialing options when

reviewing a caller ID log entry

(page 42).

OFF/CANCELOFF/CANCEL

During a call, press to hang up.

While in a menu, press to

cancel an operation, back up

to the previous menu, or exit

the menu display; or

press and hold this button to

exit to idle mode.

Press and hold while the

telephone is not in use to

erase the missed call indicator.

MENU/SELECT

Press to show the menu.

While in the menu, press to

select an item or save an

entry or setting.

pDIR/VOLUME

Press pDIR to show

directory entries (page 35).

Press to scroll up while

in menus.

While entering names or

numbers, press to move the

cursor to the right.

Press to increase the listening

volume when on a call

(page 22), or to increase the

message playback volume

(page 53).

TONE

Press to switch to tone dialing

temporarily during a call if you

have pulse service (page 24).

REDIAL/PAUSE

Press repeatedly to view

the last 10 numbers dialed

(page 20).

While entering numbers,

press and hold to insert a

dialing pause (page 33).

EQ

During an outside call,

intercom call, message or

announcement playback,

press to change the audio

quality to best suit your

hearing (page 21).

Getting started

2

Getting started

Quick reference guide - handset

Main menu

The > symbol highlights

a menu item.

>Play messages

Answering sys

Main menu

Play messages (page 53)

Answering sys (page 45)

Directory (page 32)

Caller ID log (page 39)

Intercom (page 26)

Ringers (page 11)

Set date/time (page 12)

Settings (page 13)

Website (page 18)

Using menus:

Press MENU/SELECT to show the menu.

Press qCID or pDIR to scroll through

menu items.

Press MENU/SELECT to confirm or save

changes to a highlighted menu item.

Press OFF/CANCEL to cancel an

operation, back up to the previous menu,

or exit the menu display.

•

PUSH TO TAL�

Press to initiate a one-to-one (page 28) or

one-to-group (page 29) broadcast.

Press and hold to broadcast to a group of

handsets (page 29).

p

q

Getting started

3

Quick reference guide - telephone base

IN USE indicator

On when the handset is in use, or when

the answering system is answering an

incoming call.

On when a handset is being registered.

Flashes when there is an incoming call

or when a handset is being deregistered.

Flashes when another telephone is in

use on the same line.

Message counter

Shows the number of messages or other

answering system information (page 56).

/PLAY/STOP

Press to start or stop

message playback

(page 53).

/S�IP

Press to skip a message

(page 53).

/REPEAT

Press to repeat a message.

Press twice to play the previous

message (page 53).

X/DELETE

Press to delete the message

currently playing (page 53).

Press twice to delete all old

messages when the phone is not in

use (page 54).

/ANSWER ON

Press to turn the built-in

answering system on or

off (page 46).

q/VOL/p

During message

playback, press to

adjust the listening

volume (page 53).

While in idle mode,

press to adjust the

base ringer volume

(page 52).

/HANDSET LOCATOR

While the phone is idle, press

to page all handsets (page 25).

4

Getting started

See pages 6-7 for

easy instructions.

You must install and

charge the battery before

using the telephone.

STOP!

Installation

Install the telephone base close to a telephone jack and a power outlet not

controlled by a wall switch. The telephone base can be placed on a flat surface

or vertically mounted on the wall (see page 8). For optimum range and better

reception, place the telephone base in a central and open location.

If you subscribe to high-speed Internet service (DSL - digital subscriber line)

through your telephone line, you must install a DSL filter between the telephone

line cord and the telephone wall jack (see the following page). The filter prevents

noise and caller ID problems caused by DSL interference. Please contact your DSL

service provider for more information about DSL filters.

Your product may be shipped with a protective sticker covering the handset

or telephone base display - remove it before use.

For customer service or product information, visit our website at

www.telephones.att.com or call 1 (800) 222-3111. In Canada,

dial 1 (866) 288-4268.

Avoid placing the telephone base too close to:

Communication devices such as television sets, VCRs, or other

cordless telephones.

Excessive heat sources.

Noise sources such as a window with traffic outside, motors, microwave

ovens, refrigerators, or fluorescent lighting.

Excessive dust sources such as a workshop or garage.

Excessive moisture.

Extremely low temperature.

Mechanical vibration or shock such as on top of a washing machine

or workbench.

•

Getting started

5

Telephone base and charger installation

Install the telephone base and charger, as shown below.

The telephone base is ready for tabletop use. If you want to change to wall

mounting, see Installation options on page 8 for details.

IMPORTANT INFORMATION

1. Use only the power adapter(s) supplied with this product. To order a replacement

power adapter, visit our website at www.telephones.att.com or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

2. The power adapters are intended to be correctly oriented in a vertical or floor

mount position. The prongs are not designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or cabinet outlet.

Plug the power adapter into a power outlet not

controlled by a wall switch.

Raise the antenna.•

Charger installation

Telephone base installation

Plug one end of the

telephone line cord

into the telephone jack

on the back of the

telephone base.

•

Route the power

adapter cord and the

telephone line cord

through this slot.

•

Plug the small end of

the telephone base

power adapter into the

power adapter jack

on the back of the

telephone base.

•

Plug the large end

of the power adapter

into a power outlet

not controlled by a

wall switch.

•

Plug the other end

of the telephone

line cord into a

telephone jack or

a DSL filter.

•

If you have DSL high-speed

Internet service, a DSL filter

(not included) is required.

The DSL fliter must be

plugged into the telephone

wall jack.

Telephone line cord

6

Getting started

Battery installation and charging

Install the battery, as shown below. Once you have installed the battery, the

screen indicates the battery status (see the following table). If necessary,

place the handset in the telephone base or charger to charge the battery. For

best performance, keep the handset in the telephone base or charger when

not in use. The battery is fully charged after 10 hours of continuous charging.

See the table on page 82 for battery operating times.

If the screen shows Place in charger and flashes, you need to charge the

handset without interruption for at least 30 minutes to give the handset

enough charge to use the telephone for a short time. The following table

summarizes the battery charge indicators and actions to take.

Battery indicators Battery status Action

The screen is blank, or

shows Place in charger

and (flashing).

Battery has no or very

little charge. The handset

cannot be used.

Charge without interruption

(at least 30 minutes).

The screen shows

Low battery and

(flashing).

Battery has enough charge

to be used for a short time.

Charge without interruption

(at least 30 minutes).

The screen shows

HANDSET X.

Battery is charged. To keep the battery charged,

place it in the telephone base or

charger when not in use.

BY 1021

BT183342/BT283342

Step 1

Plug the battery

connector securely

into the socket inside

the handset battery

compartment. Insert

the supplied battery

with the label THIS

SIDE UP facing up, as

indicated.

Step 2

Align the cover flat

against the battery

compartment, then

slide it upwards until

it clicks into place.

NOTE: If you are on a phone call in low battery mode, you hear 4 short beeps

every minute.

Getting started

7

Battery installation and charging

Step 3

Charge the handset by placing it face forward in

the telephone base or charger. The CHARGE light

on the top of the handset is on during charging.

IMPORTANT INFORMATION

1. Use only the supplied rechargeable battery or replacement battery (model BT183342).

To order, visit our website at www.telephones.att.com or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

2. If you do not use the handset for a long time, disconnect and remove the battery

to prevent possible leakage.

CHARGE light

After you install your telephone or power returns following a

power outage, the handset will prompt you to set the date and

time. For instructions, see Set date/time on page 12. To skip

setting the date and time, press OFF/CANCEL.

SET DATE

MM/DD/YY

p

q

SET TIME

HH/MM/--

p

q

8

Getting started

Installation options

Your telephone base is ready for tabletop use. If you want to mount your

telephone on a wall, use the provided wall mount bracket to connect with

a standard dual-stud telephone wall mounting plate. If you do not have this

mounting plate, you can purchase one from many hardware or consumer

electronic retailers. You might need a professional to install the mounting plate.

Tabletop to wall mount installation

1. Plug the power cord and telephone line into the telephone base. If you

are using a DSL filter, plug the other end of the telephone line into

the filter. Route the telephone line cord (or DSL filter) through the wall

mount bracket hole.

2. Position the telephone base, as shown below. Insert the extended tabs

(see below figure 2) of the wall mount bracket into the slots on the back

of the telephone base (marked B). Push the telephone base down until it is

securely in place.

3. Plug the telephone line cord (or DSL filter) into the wall jack. Plug the

power adapter into a power outlet not controlled by a wall switch.

4. Align the holes on the wall mount bracket with the standard wall plate

and slide the wall mount bracket down until it locks securely. Bundle the

telephone line cord and power adapter cord neatly with twist ties.

1 2

43

Getting started

9

Installation options

Wall mount to tabletop installation

1. If the telephone line cord and power adapter cord are bundled, untie

them first.

2. Push the telephone base up to detach it from the wall mount bracket.

Unplug the telephone line cord (or DSL filter) from the wall. Unplug the

power adapter from the power outlet.

3. Push the wall mount bracket up to remove it from the wall.

4. See Telephone base and charger installation on page 5.

10

Handset settings

Use the menu to change the telephone settings.

1. Press MENU/SELECT when in idle mode (when the phone is

not in use) to enter the main menu.

2. Press qCID or pDIR to scroll to the feature to be changed.

When scrolling through the menu, the > symbol indicates the

selected menu item.

3. Press MENU/SELECT to select the highlighted item.

NOTE: Press OFF/CANCEL to cancel an operation, back up to the previous menu or exit

the menu display. Press and hold OFF/CANCEL to return to idle mode.

Go to Answering system settings starting on page 45 for instructions on

how to use a system handset to modify the answering system settings, as

shown below.

Setting Page

Announcement (play, record and delete)

44-45

Answer on/off

45

Call screening

46

Number of rings

46-47

Remote access code

47

Message alert tone

48

Message recording time

48

>Play messages

Answering sys

p

q

Telephone settings

Handset settings

Ringer volume

You can set the ringer volume level (1-6) to one of six levels or

turn the ringer off. When the ringer is off, appears on the

screen.

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Ringers, then press

MENU/SELECT.

3. Press MENU/SELECT again to select >Ringer volume.

4. Press qCID or pDIR to sample each volume level.

5. Press MENU/SELECT to save your preference. There is a

confirmation tone and the screen returns to the previous menu.

NOTES:

The handset ringer volume also determines the ringer volume for

intercom calls.

If the ringer volume is set to off, that handset is silenced for all incoming calls. However, the

handset still plays the paging tone when responding to the handset locator.

If the ringer volume is set to off, caller ID will not be announced and Caller ID won’t be announced

displays briefly on the screen.

Ringer tone

You can choose one of 10 ringer tones.

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Ringers, then press

MENU/SELECT.

3. Press qCID or pDIR to scroll to >Ringer tone, then press

MENU/SELECT.

4. Press qCID or pDIR to sample each ringer tone.

5. Press MENU/SELECT to save your preference. There is a

confirmation tone and the screen returns to the previous menu.

NOTE: If you turn off the ringer volume, you do not hear ringer tone samples.

•

>

Ringer tone

Ringer volume

p

q

RINGER TONE

>

Tone 1

p

q

>

Ringer volume

Ringer tone

p

q

>Ringers

Intercom

p

q

RINGER VOLUME

p

q

11

Telephone settings

12

Handset settings

Set date/time

The answering system announces the day and time of each message prior

to playing it. Before using the answering system, set the date and time as

follows. If you subscribe to caller ID service, the day, month and time are

set automatically with each incoming call. The year must be set so that the

day of the week can be calculated from the caller ID information. You can

turn off the date and time settings of the caller ID service and set the date

and time manually (see Use caller ID to automatically set date and time

on page 17).

After a power failure or handset registration, the system reminds you to set

the date and time.

Follow the steps to set the month, day, year and time.

1. When the handset is in idle mode, press MENU/SELECT to

enter the main menu.

2. Press qCID or pDIR to scroll to >Set date/time and then

press MENU/SELECT.

3. Press qCID or pDIR to select the month, then press

MENU/SELECT, or enter the number using the dialing keys.

4. Press qCID or pDIR to select the day, then press

MENU/SELECT, or enter the number using the dialing keys.

5. Press qCID or pDIR to select the year, then press

MENU/SELECT, or enter the number using the dialing keys,

then press MENU/SELECT to move on to set the time.

6. Press qCID or pDIR to select the hour, then press

MENU/SELECT, or enter the number using the dialing keys.

7. Press qCID or pDIR to select the minute, then press

MENU/SELECT, or enter the number using the dialing keys.

8. Press qCID or pDIR to highlight AM or PM, or press 2 for AM or 7 for PM.

Then, press MENU/SELECT to confirm. There is a confirmation tone and the

screen returns to the previous menu.

NOTE: If the clock is not set when a message is recorded, the system announces, “Time and

day not set,” before it plays the message.

SET DATE

MM/DD/YY

p

q

SET TIME

HH:MM --

p

q

Ringers

>Set date/time

p

q

Handset settings

LCD language

You can select the language used for all screen displays.

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press

MENU/SELECT.

3. Press MENU/SELECT to choose >LCD language.

4. Press qCID or pDIR to highlight >English, >Français

or >Español, then press MENU/SELECT. The screen prompts

Set English/Français/Español as LCD language?

5. Press MENU/SELECT to confirm. There is a confirmation tone

and the screen returns to the previous menu.

NOTE: If you accidentally change the LCD language to French or Spanish, you can reset it

back to English without going through the French or Spanish menus. Press MENU/SELECT

in idle mode, then enter 364#. There is a confirmation tone.

Caller ID announce

The caller ID announce feature lets you know who’s calling without having

to look at the display. When you have an incoming call, the handset and/or

base speaks “Call from...” and the name of the caller based on the directory

or caller ID information. If the caller’s name is private or unknown, the phone

number up to the last 11 digits will be spoken. If the caller’s phone number

is also private or unknown, no information will be spoken. By default, the

caller ID announce feature is programmed On.

To turn on/off the caller ID announce on your handset or base:

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press

MENU/SELECT.

3. Use qCID or pDIR to scroll to >Caller ID annc, then

press MENU/SELECT.

4. Use qCID or pDIR to highlight the desired option, then

press MENU/SELECT.

Set all On/Off - Change the setting for the base and all

handsets.

Local handset - Change the setting for that handset only.

Base - Change the setting for the telephone base only.

5. Use qCID or pDIR to highlight >On or >Off, then press

MENU/SELECT. There is a confirmation tone and the screen

returns to the previous menu. If you change the setting forIf you change the setting for

Set all On/Off, the screen shows CID Annc ON/OFF on all HS and BS.

•

HS CID ANNOUNCE

>On

p

q

CALLER ID ANNC

>LOCAL HANDSET

p

q

LCD language

>Caller ID annc

p

q

LCD LANGUAGE

>

English

>

LCD language

Caller ID annc

p

q

p

q

13

Telephone settings

14

Handset settings

NOTES:

To use the caller ID announce feature, you must subscribe to caller ID service from your

telephone service provider.

When there are up to 5 handsets registered, the telephone system supports caller ID announce

for all handsets. If 6 or more handsets are registered, the system supports caller ID announce for

the first 4 registered handsets only.

This feature does not announce information for call waiting calls.

It takes at least 2 rings for the phone to receive caller ID information and announce it. If the

phone is answered before the end of the second ring, the phone won’t have time to announce

the caller’s information.

Pronunciation of names may vary with this feature. Not all names may be pronounced correctly.

Caller ID announce is available in English only.

Set speed dial voicemail number

This feature lets you save your voicemail number for easy access when you

press and hold the 1 key.

To set your voicemail number:

1. Press MENU/SELECT in idle mode to enter the main menu.

2. Use qCID or pDIR to scroll to >Settings, then press

MENU/SELECT.

3. Use qCID or pDIR to scroll to >Voicemail #, then press

MENU/SELECT.

4. Use the dialing keys to enter the voicemail access number

provided by your telephone service provider (up to 30

digits) when prompted.

Press qCID or pDIR to move the cursor to the left or right.

Press MUTE/DELETE to erase a digit.

Press and hold MUTE/DELETE to erase all digits.

Press REDIAL/PAUSE to enter a three-second dialing pause

(a p appears).

5. Press MENU/SELECT to save. Voicemail # saved shows on

the handset.

•

VOICEMAIL #

_

p

q

LCD language

>Voicemail #

p

q

Set date/time

>Settings

p

q

Page is loading ...

AT&T CL82351 User manual

This manual is also suitable for

AT&T CL82351 User manual

Related papers

Other documents