XiNCOM Twin WAN XC-DPG603 User manual

         



CUTTING EDGE INNOVATIONS.

Twin WAN DNS IP VPN Gateway

→

Table of Contents

Introduction 4

Features 5

Physical Details 7

Basic Setup 9

Conﬁguring your LAN 10

Connecting Broadband Modems 12

Conﬁguring for Interent Access 13

Conﬁguring your LAN PCs 14

Advanced Port 16

Port Options 17

Load Balance 18

Advanced PPPoE 19

Advanced PPTP 20

Advanced Setup 21

Host IP Setup 22

Virtual Server 23

Custom Virtual Server 24

Special Applications 25

Dynamic DNS 26

Multi DMZ 27

UPnP 27

Advanced Features 28

Security Management 30

Block URL 31

Access Filter 31

Session Limit 32

Firewall Exception 32

XC-DPG603

Twin WAN DNS IP

VPN Gateway

2

Table of Contents

QoS Conﬁguration 33

VPN Conﬁguration 34

IPSec Global Setting 35

Policy Setup 36

DNS Conﬁguration 38

Domain Name Server Conﬁguration 40

Map Host URL 42

Management Assistant 43

SNMP 43

Email Alert 43

Syslog 44

Upgrade Firmware 45

Operation & Status 47

System Status 47

Restore Factory Defaults 48

WAN Status 48

LAN Status 48

Advanced LAN Conﬁguration 49

Existing DHCP Server 49

Static Routing 50

Appendices 52

Appendix A 52

Appendix B 53

Appendix C 56

3

→

Chapter 1 - Introduction

The XiNCOM XC-DPG603 is a revolutionary DNS to IP VPN Gateway that provides advanced networking services

most commonly found in enterprise class infrastructures at a fraction of the cost. XiNCOM tailors these services

with innovative features such as inbound/outbound load balancing, auto-failover, and a built-in VPN endpoint. The

XC-DPG603’s primary features are full VPN Load Balancing with Automatic Failover and the Authorative DNS

fucntion with Inbound Load Balancing. The VPN capability will allow for two concurrent VPN tunnels that will

load balance both inbound and outbound trafﬁc requests. Full redundancy is assured when establishing a VPN

tunnel on each WAN port. The authoritative DNS feature load balances inbound trafﬁc requests to the respective

IP address on a network infrastructure that hosts content on multiple servers. High throughput of inbound

and outbound requests are managed by dual WAN ports that utilize the combined bandwidth of two separate

concurrent broadband connections including DSL, Cable, and/or T1.

Use TWO ISPs for expanded bandwidth and redundancy

Using two separate ISPs provides redundant connectivity to the Internet. In the event that one ISP goes

down, the XC-DPG603 auto-fails over to the other ISP service. Redundancy to the Internet provides a

truly uninterrupted connection for a business’s customers while maintaining uptime and productivity for its

employees.

Robust Security Features

The XC-DPG603 also features NAT, a Stateful Packet Inspection (SPI) Firewall, DHCP server, Access Filters,

and a built-in VPN endpoint to secure a business’s network services. The Quality of Service (QoS) feature

schedules and directs a network’s trafﬁc to take advantage of available bandwidth. The XC-DPG603 UPnP

support can dynamically open and close ports required by certain software automatically. Increased bandwidth

and redundant connectivity to the Internet provides cost-effective bandwidth solutions to expensive leased

telecommunication lines for your network infrastructure.

Package Contents

The following items should be included:

• XC-DPG603 Twin WAN DNS to IP VPN Gateway

• Power Adapter (5V)

• Quick Installation Guide

• CD-ROM containing the on-line manual.

• Two CAT RJ-45 Ethernet Cables

• Rack Mounts for a standard 19” server rack

XC-DPG603

Twin WAN DNS IP

VPN Gateway

Chapter Contents

• Introduction

• Features

• Physical Details

4

Features

Built-in VPN Endpoint

Full VPN Endpoint with support for up to 50 VPN tunnels using the IPsec encryption protocol.

Authoritative DNS to IP Gateway

The XC-DPG603 is an authoritative DNS to IP gateway that resolves a domain name to its respective IP

addresses. This new capability allows for inbound failover and load balancing for servers located behind

the gateway. Using dual WAN ports simultaneously increases available bandwidth for both uploads and

download requests. You can set load balance type by Packets, Bytes rx+tx and Sessions.

Multiple Connection Methods

All popular DSL and Cable Modems and connection methods are supported, including Fixed IP, Dynamic

IP, PPPoE, even multiple-session PPPoE.

2 x 10/100 WAN Ports

The XC-DPG603 incorporates dual 10/100 WAN ports, complete with auto-crossover for easy

connection to an existing network. All popular DSL and Cable Modems and connection methods are

supported, including Fixed IP, Dynamic IP, PPPoE, even multiple-session PPPoE.

4-Port 10/100 Switch

The XC-DPG603 incorporates a 4-port 10/100 N-Way Ethernet Switch, complete with auto crossover for

easy connection to an existing network.

Automatic Fail-over

If one broadband connection goes down all trafﬁc is automatically re-routed through the second

broadband connection.

Stateful Packet Inspection (SPI) Firewall

Protects your network using advanced SPI against malicious and DDoS attacks.

Advanced NAT features

Access Filters, DMZ, DDNS, Remote Management, Dynamic or Static Routing, Special Applications,

Virtual Servers, SNMPv1.

Access Filter

Gain ﬁne control over the Internet access and applications available to LAN users with a powerful URL

Blocking Engine. Five (5) user groups are available, and each group can have different access rights.

Block URL

Use this feature to block access to undesirable Web sites by LAN users. You can even have different

settings for different groups of PCs.

Figure 2. Load Balancing

Load Balance two concurrent broadband connections in any combination to expand a

network’s bandwidth to the Internet. The XC-DPG603 supports T1, xDSL, Cable, and Satillite

broadband connections.

Active connection from the ISP

The XC-DPG603 load balances

both inbound and outbound

trafﬁc requests.

Figure 3. Automatic Fail-over

In the event of one connection going down, all trafﬁc is re-routed to the second WAN

port utilizing the live broadband connection from the second ISP. This provides true

redundancy to ensure a network remains connected to the Internet.

Active connection from the ISP

Inactive connection from the ISP

All incoming and outgoing

trafﬁc from a LAN has an

uninterrupted connection to

the Internet when one of the

two connections fail.

Figure 1. How it works

1

2

3

4

A client computer makes a request to

access www.(yourdomain).com.

The request goes to the ISP’s DNS

server and the DNS server replies

with the IP address of the DNS

responsible for that domain.

The request is then processed by the

Authoritative DNS of that domain

and provides the IP address of the

speciﬁed server.

The client can then access the web

server.

Internet

5

Other Features:

DHCP Server Support

Dynamic Host Conﬁguration Protocol provides a dynamic IP address to PCs and other

devices upon request. The XC-DPG603 can act as a DHCP Server for devices on your

local LAN.

Multi Segment LAN Support

LANs containing one or more segments are supported via the XC-DPG603’s built-in

static routing table.

ARP proxy

The ARP proxy feature allows you to assign an external (Internet) IP address to the

XC-DPG603’s LAN port. This allows Servers on your LAN to have external (Internet) IP

addresses.

Easy Setup

Use your favorite WEB browser for conﬁguration.

Remote Management

The XC-DPG603 can be managed from any PC on your LAN. If the Internet connection

exists, the XC-DPG603 can be setup to be conﬁgured remotely via the Internet.

Password Protected Conﬁguration

Optional password protection is provided to prevent unauthorized users from modifying

the XC-DPG603’s conﬁguration data and settings.

HTTP Firmware Upgrade and backup

The web management feature allows you to use HTTP to upgrade new ﬁrmware and

backup system conﬁguration from local or remote locations.

Email Alert

The XC-DPG603 will send an alert via email to the system administrator in the event a

single or both WAN connections go down.

Syslog

Generates real time system information on the web page or sends to a particular

computer. This is used for monitoring and diagnosis purposes.

DNS Conﬁguration

This sets the inbound load balancing features for the XC-DPG603. Users have to

construct a DNS server in order to enable the inbound load balancing cababilities.

Map Host URL

In addition to the DNS conﬁguration, Map Host URL allows for users to select a URL to

map to the IP address of a local host.

QoS Conﬁguration

You will be able to schedual and direct your network trafﬁc to take advantage of your

available bandwidth. This function allows for speciﬁed packets with higher priority to pass-

through such as Internet phone, video conference, and other real-time applications.

UPnP

UPnP dynamically opens and close ports required by certain software automatically.

Features

6

Twin WAN DNS IP VPN Gateway

XC-DPG603

Front Panel:

Operation of the Front Panel LEDs is as follows:

System:

Power

OFF - No Power.

ON - Normal Operation

Status

OFF - Normal Operation

ON - Firmware not loaded or Hardware Error

Blinking - Data in/out

WAN:

LINK/ACT

ON - Physical connection to the Broadband modem on WAN port 1/2 established.

OFF - No physical connection on WAN port 1/2.

10M/100M

ON - Physical connection using 100BaseT on WAN port 1/2 established.

OFF - 10BaseT connection or no connection on WAN port 1/2.

LAN:

LINK/ACT

ON - Physical connection or data in/out.

OFF - No physical connection.

10M/100M

ON - The corresponding LAN port is using 100BaseT.

OFF - 10BaseT connection on the corresponding LAN port or no connection.

Physical Details

7

Physical Details

LAN Ports WAN1WAN2 ResetDC 5V

Front Panel Status and Error conditions

LED Action Condition

WAN1 LINK/ACT & 10M/100M LEDs ﬂash alternatively. Firmware Download in progress.

WAN1 LINK/ACT & 10M/100M LEDs ﬂash concurrently. MAC address not assigned.

WAN1 LINK/ACT & 10M/100M LEDs solid On SDRAM error

WAN2 LINK/ACT & 10M/100M LEDs solid On Timer/Interrupt error

LAN1 LINK/ACT & 10M/100M LEDs solid On LAN/WAN error

Rear Panel:

WAN Ports

Connect the primary Broadband Modem to

WAN 1 and the second Broadband Modem

on WAN 2.

LAN Ports

Connect the PCs to these ports. Both 10BaseT and

100BaseT connections can be used simultaneously.

Note: Any port will automatically operate as an “Uplink” port if

required. Use a standard RJ-45 Ethernet cable to connect to

any port to another hub or switch.

Reset Button

Press the Reset button once for a warm

reboot. To reset the XC-DPG603 to default

settings, press and hold the reset button for

30 seconds.

Default Settings

When the XC-DPG603 has ﬁnished booting, all conﬁguration settings will be set to the factory defaults, including:

• The IP Address is set to its default value of 192.168.1.1 with a Network Mask of 255.255.255.0

• DHCP Server is enabled

• User Name: admin

• Password cleared (no password)

8

Chapter 2 - Basic Setup

Overview

Basic setup of your XC-DPG603 wil involve the following steps:

1. Connect the XC-DPG603 to one (1) PC and conﬁgure it to your existing LAN.

2. Connecting one or two Broadband Modems to your XC-DPG603.

3. Conﬁguring the XC-DPG603 for Interent Access.

4. Conﬁguring all PCs on your LAN to use the XC-DPG603.

Requirements:

• One or two Broadband modems (T1, xDSL, Cable, and Satillite) with an active account from your ISP(s).

• Two standard 10/100BaseT network (UTP) cables with RJ-45 connectors.

• TCP/IP network protocol must be installed on all PCs.

XC-DPG603

Twin WAN DNS IP

VPN Gateway

Chapter Contents

• Overview

• Procedure

1. Conﬁguring your LAN

2. Connecting Broadband Modems

3. Conﬁguring for Internet Access

4. Conﬁguring your LAN PCs

TCP/IP Enabled PCs

Broadband ModemsCAT5 Ethernet Cables

9

→

Configuring the XC-DPG603 for your LAN

a

1.

2.

3.

4.

5.

6.

7.

8.

9.

Procedure

Use a standard LAN cable to connect your PC to any LAN port on the XC-DPG603.

Connect the power adapter and power up the XC-DPG603. Only use the power adapter

provided with the product; using a different one may cause hardware damage.

Start your PC or restart your PC if it is already running. Once restarted, the PC will then

obtain an IP address from the XC-DPG603.

Start your WEB browser.

In the Address or Location box enter:

HTTP://192.168.1.1

You will be prompted for the User Name and password, as shown in Figure 1.

Enter admin for the “User Name” and leave the “Password” blank.

• The User Name is always set to admin

• You can and should set a password, using the following Admin Password screen

After the login, you will then see the Admin Password screen, as shown in Figure 2.

Assign a password in both the Password and Verify Password ﬁelds and press the

Submit button.

From the setup menu, select Basic Setup and then LAN & DHCP from the submenu.

You will see a screen like the example in Figure 3.

No Response?

Is your PC using a Fixed IP address?

If so, you must conﬁgure your PC to use an IP address within the range

192.168.1.2 to 192.168.1.254, with a Network Mask of 255.255.255.0. See

Appendix B – Windows TCP/IP Setup for details.

Be sure to check for the following:

• the XC-DPG603 is properly installed

• the Ethernet cable to the XC-DPG603 is properly attached

• the XC-DPG603 is powered ON

Figure 2. Admin Password

Figure 1. Password Dialog

10

Twin WAN Gateway

XC-DPG603

Ensure these settings are suitable for your LAN:

• The default settings are suitable for many situations.

• See the following table for details of each setting.

Figure 3. LAN & DHCP

Configuring the XC-DPG603 for your LAN

11

This is the IP address for the XC-DPG603 when seen from the local LAN. Use the defualt value unless the address is already in use or your LAN is using a

different IP addres range. In the latter case, enter an unused IP Address from within the range used by you LAN

DPG603 is attached (the same value as the PCs on that LAN segment).

DHCP Server Setup - If Enabled, the XC-DPG603 will allocate IP Addresses to PCs (DHCP clients) on your LAN when they start up. The default and

provide the IP address of the XC-DPG603 as the

Default Gateway

.

LAN Ports WAN1WAN2 ResetDC 5V

Connecting two broadband modems

a

1.

2.

3.

4.

5.

Procedure

Ensure the XC-DPG603 and the DSL/Cable modem are powered OFF.

Leave the modem or modems connected to their data line.

Connect the Broadband modem(s) to the XC-DPG603.

If using only one (1) Broadband modem, connect it to the “WAN 1” port.

Use standard LAN cables to connect PCs to the LAN ports on the XC-DPG603.

Both 10BaseT and 100BaseT connections can be used simultaneously.

Use a standard CAT-5 Ethernet cable to connect any port on the XC-DPG603 to

a standard port on another hub. Any LAN port on the will automatically act as an

“Uplink” port when required.

Power Up

Power on the Cable or DSL modem(s).

Connect the supplied power adapter to the XC-DPG603 and power up.

Check the LEDs

The Power LED should be ON.

The WAN – Link LED should be ON when the corresponding WAN port is

connected toa broadband modem.

For each PC connected to the LAN ports, the corresponding LAN LED (either 10 or

100) should be ON.

Broadband Modem Broadband Modem

Figure 4. Installation Diagram for XC-DPG603

Local Area Network

12

Select Primary Setup from the menu.

Conﬁgure WAN 1 and/or WAN 2 as required.

For any of the following situations, refer to Chapter 3: Advanced Port Setup

for any further conﬁguration which may be required such as:

• Using both ports

• Multiple IP addresses on either port

• Multiple PPPoE sessions

• PPTP connection method

1.

2.

Settings - Primary Setup

Connection Mode Select the appropriate setting:

• Enable – Select this if you have connected a broadband modem to this port.

• Disable – Select this if there is no broadband modem connected to this port.

• Backup – Select Enable for the primary port, and Backup for the secondary port. The Backup port will only be used if the primary port fails.

Connection Type Check the requirements supplied by your ISP, and select the appropriate option.

• Static IP – Select this if your ISP has provided a Fixed or Static IP address. Then enter the data into the Address Info ﬁelds.

• Dynamic IP – Select this if your ISP provides an IP address automatically, when you connect. You can ignore the Address Info ﬁelds.

• PPPoE – Select this if your ISP uses this method (PPPoE software that is usually provided by your ISP is not required to be used when selecting this method).

If this method is selected, you must complete the PPPoE dialup ﬁelds.

Note: If using the PPTP connection method, select Static IP or Dynamic IP to correspond to the IP address method used by your ISP.

Address Info This is for Static IP users only. Enter the address information provided by your ISP. If your ISP provided multiple IP address, you can use the Multi-DMZ screen to

assign the additional IP addresses.

PPPoE / PPTP Dialup This is for PPPoE and PPTP users only.

• Enter the Username and Password provided by your ISP.

• If using PPTP, enable the PPTP Connection checkbox and enter the IP address of the PPTP server.

• Host name (Optional For PPPoE) - This ﬁeld is used by a Host to uniquely associate an access concentrator to a particular Host request.

Note: There are additional PPPoE/PPTP options on the Port Options screen. To use multiple PPPoE sessions on either port, conﬁgure the Advanced PPPoE screen.

DNS If using a Fixed IP address, you MUST enter at least 1 DNS address. If using Dynamic IP or PPPoE, the DNS information is optional.

Optional

• Host name – This is required by some ISPs. If your ISP provided a Host Name, enter it here. Otherwise, you can use the default value.

• Domain name – This is required by some ISPs. If your ISP provided a Domain Name, enter it here. Otherwise, you can use the default value.

• MAC address – Some ISP’s record your MAC address (also called “Physical address” or “Network Adapter address”).

Setup of the XC-DPG603 is now complete. PCs on your LAN must now be conﬁgured. See the following section for details.

Figure 5. Primary Setup Screen

Configuring for Internet Access

13

Configure PCs on your LAN

Overview

For each PC, the following may need to be conﬁgured:

TCP/IP network settings

Internet Access conﬁguration

TCP/IP Settings

When using Windows 95/98/ME/2000/XP and the XC-DPG603’s TCP/IP default settings,

no changes need to be made. Just start or reboot your PC.

By default, the XC-DPG603 will act as a DHCP Server, automatically providing a

suitable IP Address (and related information) to each PC when the PC boots up.

For all non-Server versions of Windows, the default TCP/IP setting is to act as a

DHCP client. In Windows, this is called Obtain an IP address automatically. Just

start (or restart) your PC, and it will obtain an IP address from the XC-DPG603.

If using ﬁxed IP addresses on your LAN, or you wish to check your TCP/IP settings,

refer to Appendix B – Windows TCP/IP Setup.

Internet Access

To conﬁgure your PCs to use the XC-DPG603 for Internet access, follow this procedure:

For Windows 9x/2000

Select Start Menu > Settings > Control Panel > Internet Options.

Select the Connection tab, and click the Setup button.

Select I want to set up my Internet connection manually or I want to connect

through a local area network (LAN) and click Next.

If I connect through a local area network (LAN) is selected, ensure all of the

boxes on the following Local area network Internet Conﬁguration screen are

unchecked.

Check the No option when prompted Do you want to set up an Internet mail

account now?.

Click Finish to close the Internet Connection Wizard.

Setup is now completed.

1.

2.

3.

4.

5.

6.

For Windows XP

Select Start Menu > Control Panel > Network and Internet Connections.

Select Set up or change your Internet Connection.

Select the Connection tab, and click the Setup button.

Cancel the pop-up Location Information screen.

Click Next on the New Connection Wizard screen.

Select Connect to the Internet and click Next.

Select Set up my connection manually and click Next.

Check Connect using a broadband connection that is always on and click Next.

Click Finish to close the New Connection Wizard.

Setup is now completed.

1.

2.

3.

4.

5.

6.

7.

8.

9.

Accessing AOL

To access AOL (America On Line) through the XC-DPG603, the AOL for Windows

software must be conﬁgured to use TCP/IP network access, rather than a dial-up

connection. The conﬁguration process is as follows:

Start the AOL for Windows communication software. Ensure that it is Version

2.5, 3.0 or later. This procedure will not work with earlier versions.

Click the Setup button.

Select Create Location, and change the location name from “New Locality” to

“XC-DPG603”.

Click Edit Location. Select TCP/IP for the Network ﬁeld. (Leave the Phone

Number blank.)

Click Save, then OK. Conﬁguration is now complete.

Before clicking “Sign On”, always ensure that you are using the “XC-DPG603”

location.

14

For Apple Clients

Open the TCP/IP Control Panel.

Select Ethernet from the Connect via pop-up menu.

Select Using DHCP Server from the Conﬁgure pop-up menu. The DHCP Client ID

ﬁeld can be left blank.

Close the TCP/IP panel, saving your settings.

Note: If using manually assigned IP addresses instead of DHCP, the required changes

are:

• Set the Router Address ﬁeld to the XC-DPG02’s IP Address.

• Ensure your DNS settings are correct.

1.

2.

3.

4.

For Linux Clients

To access the Internet via the XC-DPG603, it is only necessary to set the XC-DPG603

as the “Gateway” and ensure your Name Server settings are correct. Make sure you are

logged in as “root” before attempting any changes.

Fixed IP Address

By default, most Unix installations use a ﬁxed IP Address. If you wish to continue

using a ﬁxed IP Address, make the following changes to your conﬁguration.

Set your Default Gateway to the IP Address of the XC-DPG603.

Ensure your DNS (Name server) settings are correct

To act as a DHCP Client (recommended):

The procedure below may vary according to your version of Linux and X -windows

shell.

Start your X Windows client.

Select Control Panel - Network

Select the “Interface” entry for your Network card. Normally, this will be called

“eth0”.

Click the Edit button, set the protocol to DHCP, and save this data.

To apply your changes use the Deactivate and Activate buttons, if available OR

restart your system.

1.

2.

3.

4.

5.

Configure PCs on your LAN

15

→

Chapter 3 - Advanced Port

Overview

Port Options contains some options which can be set on either or both WAN ports. For most situations, the

default values are satisfactory.

Load Balance screen is only functional if you are using both WAN ports. It allows you to determine the

proportion of WAN trafﬁc sent through each port.

Advanced PPPoE setup is required if you wish to use multiple sessions on one or both of the WAN ports. It

can also be used to manually connect or disconnect a PPPoE session. Otherwise, this screen can be ignored.

Advanced PPTP setup is required if using the PPTP connection method.

XC-DPG603

Twin WAN DNS IP

VPN Gateway

Chapter Contents

• Overview

• Port Options

• Load Balance

• Advanced PPPoE

• Advanced PPTP

16

Port Options

Figure 6. Port Options

Connection Validation PPPoE / PPtP Connection Options Transparent Bridge Mode

Health Check

Use this ﬁeld to select the type of connection validation

to perform. When set to ICMP, the XC-DPG603 sends

out ICMP echo requests. When set to HTTP, the XC-

DPG603 requests web pages.

Alive Indicator

This is the IP address used to check if the WAN

connection is operational. When using HTTP, put in a

valid IP address of a web server. When this ﬁeld is blank,

the ISP gateway IP address is used.

Note: This is not used for PPPoE connections.

MTU

The Maximum Transmission Unit is used when

determining the packet size to be used on the WAN

interface. Normally, this does not need to be changed, but

if your ISP advises you to use a particular MTU, enter it

here.

Auto Dialup

When set to Enable a connection will be established

whenever outgoing WAN trafﬁc is detected. If not

Enabled, you must establish a connection manually.

Auto Disconnect

This determines when an idle connection will be

terminated. Enter the required time period.

Echo Time

This determines how often an Echo request is sent to the

PPPoE server. The Echo request is used to determine if

the connection is still valid. Normally, there is no need to

change the default value.

Echo Retry

The number of time the Echo request will be sent if there

is no response to the ﬁrst request. Normally, there is no

need to change the default value.

Bridge Mode

When set to Enable, this WAN port does not use NAT &

Load Balance function when LAN/WAN IP have the real

IP addresses on the same network segment.

Trafﬁc Management

Strict Binding - When a WAN port connection is

disconnected, the packets will not go to another WAN

port.

Loose Binding - When the WAN port connection is

connected, the packets will go another WAN port.

Load Balancing - This will mix real and private IP’s on

the LAN side doing the load balancing.

17

Load Balance

Figure 7. Load Balance Console

Conﬁguring Load Balancing

The Twin WAN line of products uses a session based Load Balancing algorithm by allowing you to

manage sessions using several different options:

Bytes rx+tx

By monitoring real time speed of both WAN connections, the XC-DPG603 will

establish new sessions on the WAN port with the lower speed. Use this if there is

a fairly even speed on both lines and would like to beneﬁt the most from the speed

available.

Packets rx+tx

Same as above but in this case, the XC-DPG603 monitors the packet ﬂow and tries

to maintain an even number of packets. Use this if transmitting a lot of small packets,

such as web browsing and Usenet. This helps you maintain the best latency.

Sessions

Established

The XC-DPG603 tries to maintain an even number of sessions on each WAN port by

looking at the current amount of sessions currently established. This is a very general

setting only to be used if you have similar types of connections (Cable and Cable, DSL

and DSL) to promote good Internet trafﬁc.

Settings - Load Balance

Load Balance

Conﬁguration

• Enable – Use this to enable your Load Balance settings.

• Balance Type – Select the desired Balance Type:

- Bytes rx+tx – Trafﬁc is measured by Bytes.

- Packets rx+tx – Trafﬁc is measured by Packets.

- Sessions established – Trafﬁc is measured by Sessions.

• Loading Share on WAN 1 – Enter the percentage (%) of trafﬁc to be sent over WAN 1. The WAN port with the greater bandwidth should

be given a higher percentage of trafﬁc over the other WAN port.

Click the “Update” button to save your changes.

NAT Statistics

This section displays the current data about WAN 1 and WAN 2. You can use this information to help you “ﬁne-tune” the settings above.

Interface Statistics

This section displays cumulative statistics.

Use the “Restart Counters” button to restart these counters when required.

Buttons

• Update – Save the settings on this screen.

• Refresh – Update the data on screen.

• Restart Counters – Restart the counters used in the “Interface Statistics” section.

18

Advanced PPPoE

Figure 8. Advanced PPPoE

Settings - Advanced PPPoE

WAN Port

PPPoE Session

Select the desired Port and Session, then click the “Select” button. The data for the selected Port/Session will then be displayed in the

WAN IP Account section.

WAN IP Account

• User Name – Enter the PPPoE user name assigned by your ISP.

• Password – Enter the PPPoE password assigned by your ISP.

• Verify Password – Re-enter the PPPoE password assigned by your ISP.

• IP Address – If you have a ﬁxed IP address, enter it here. Otherwise, this ﬁeld should be left at 0.0.0.0.

• Host Name – This ﬁeld is used by a Host to uniquely associate an access concentrator to a particular Host request.

Action

Use the “Connect” and “Disconnect” buttons to establish or terminate a connection on this session.

Connection Status

This displays the current connection status for each session.

The screen is required in order to use multiple

PPPoE sessions on the same WAN port.

It can also be used to manually connect or

disconnect a PPPoE session.

19

Advanced PPTP

Figure 9. Advanced PPTP

Settings - Advanced PPTP

WAN Port

Select the desired Port and click the “Select” button. The data for the selected Port will then be displayed in the WAN IP Account section.

WAN IP Account

• User Name – The PPTP user name (login name) assigned by your ISP.

• Password – This ﬁeld is associated with the User Name above. This is assigned by your ISP and used to login to the PPTP Server.

• Verify Password – Re-enter the PPTP password assigned by your ISP.

• IP Address – Enter the IP address of the PPTP Server. (This is provided by your ISP)

• Static IP Address – If you have a ﬁxed IP address, enter if here. Otherwise, this ﬁeld should be left at 0.0.0.0.

Action

Use the “Connect” and “Disconnect” buttons to establish or terminate a connection on this session.

Connection Status

This displays the current connection status.

20

Page is loading ...

XiNCOM Twin WAN XC-DPG603 User manual

This manual is also suitable for

XiNCOM Twin WAN XC-DPG603 User manual

Related papers

Other documents