Rockford Fosgate Punch Z RFZ3410 Installation & Operation Manual

Brand: Rockford Fosgate

Model: Punch Z RFZ3410

Type: Installation & Operation Manual

700RFP4112

This is a Package that consists of

575RFP4112

044H1212SX

B. IMPORTANT!!! Refer to the driver documentation to determine

whether to use a sealed or ported enclosure. If the manufacturer

recommends a sealed enclosure continue to step C. If the

manufacturer recommends a ported enclosure, refer to the tuning

chart on the back for porting procedures.

C. Connect the speaker leads from the woofers to the terminal cups.

Be sure to wire the positive to red and the negative to black.

D. Align the mounting holes on the driver with the recesses in the

Q-Ring. If necessary, rotate the Q-Ring and the driver to properly

align printing on the dustcap.

E. Using the supplied screws, securely mount the driver in the

enclosure. It is recommended to start all screws and then come

back and retighten screws to prevent the driver basket from being

bent or distorted during mounting.

A. Experiment to find the best location for your new subwoofer system. Subwoofers for hatchbacks can

fire either upward, forward or backward for the best sound. Positioning makes a big difference in

sound quality.

B. FLYING SPEAKERS ARE DANGEROUS!! Permanent mounting is not only the safest installation, but

usually produces the best sound quality too. However, if you decide to mount your speakers so that

they can be easily removed, there are many suitable types of brackets available at most hardware

stores. The key to selecting such hardware is to make sure that the mounting will hold the speaker

securely. Good luck and enjoy your new subwoofer!

QLH-1.2512sx/dx

QLT-1.2512sx

Thanks for choosing Q-Logic! - the ONLY subwoofer enclosure with the Q-Ring (patent-

pending), a multi-diameter woofer mounting adapter that can extract optimum performance

from any driver you choose! Follow the 4-step instructions CAREFULLY to custom fit your driver

to the enclosure. YOUR INSTALLATION CAN MAKE A HUGE DIFFERENCE IN THE

SOUND QUALITY!

A. Using one of the supplied rolls, apply the foam tape to the back of

the driver. Use care to apply the foam tape so that all of the mounting

holes are COMPLETELY covered.

B. Place ring face down with tabs sticking up. Apply foam tape to the

back of the mounting ring against the inside edge of the

mounting ring.

C. If you know the mounting diameter of your driver, use the trim guide

to determine if you need to trim the mounting ring.

A. Place the driver face down on a flat surface. Place the mounting ring

over the driver with the locating tabs pointing up. If the mounting

ring does not rest on the foam tape on the driver you will need to trim

the centering tabs.

B. Using a pair of diagonal cutters or scissors, trim each of the 6

centering tabs. Recheck the fit.

Step 1: Prepare the driver and Q-Ring.

C. When the mounting ring fits against the foam tape on the driver,

the driver is ready to be mounted into the enclosure.

A. Place the mounting ring in the enclosure and align the arrow on the mounting ring

with the alignment mark on the silver ring.

Use this position for mounting drivers with offset

hole alignment. (see illustration)

Use this position for mounting drivers with offset

hole alignment. (see illustration)

Step 2: Adjust the Q-Ring to fit your driver.

Step 3: Mount the driver.

CONVENTIONAL

HOLE ALIGNMENT

8 HOLE

OFFSET ALIGNMENT

6 HOLE

OFFSET DRIVERS

Use this position for mounting drivers with

conventional hole alignment. (see illustration)

Step 4: Mount your speakers!

11.36

11.12

11.00

10.75

VAS

CU.FT. 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8 8.5 9 9.5 1 0 10.5 11 11.5 12 12.5 13 13.5 14

Port Tuning

LITERS 28.3 42.5 56.6 70.8 85.0 99.1 113.3 127.4 141.6 155.8 156.3 156.8 157.3 157.8 158.3 158.8 159.3 159.8 160.3 160.8 161.3 161.8 162.3 162.8 163.3 163.8 164 .3

Length Frequency

19 11.8 11.4 11.1 10.7 12.1 37

20 11.9 11.5 11.1 10.7 10.3 10.0 9.7 9.4 11.3 38

21 11.9 11.4 10.9 10.5 10.1 9.8 9.4 9.1 8.8 8.5 8.3 10.6 39

FS 22 11.6 11.1 10.6 10.1 9.7 9.3 9.0 8.7 8.3 8.1 7.8 7.5 7.3 10.0 40

23 11.6 11.0 10.4 9.9 9.5 9.0 8.7 8.3 8.0 7.7 7.4 7.1 6.9 6.7 6.4 9.3 41

24 11.8 11.1 10.4 9.8 9.3 8.9 8.5 8.1 7.7 7.4 7.1 6.8 6.6 6.3 6.1 5.9 5.7 8.8 42

25 11.4 10.6 10.0 9.4 8.9 8.4 8.0 7.6 7.2 6.9 6.6 6.3 6.1 5.8 5.6 5.4 5.2 5.0 8.2 43

26 11.2 10.3 9.6 9.0 8.5 8.0 7.5 7.2 6.8 6.5 6.2 5.9 5.6 5.4 5.2 5.0 4.8 4.6 4.4 7.7 44

27 11.1 10.2 9.4 8.7 8.2 7.6 7.2 6.8 6.4 6.1 5.8 5.5 5.3 5.0 4.8 4.6 4.4 4.2 4.1 3.9 7.3 45

28 11.1 10.1 9.2 8.5 7.9 7.4 6.9 6.5 6.1 5.8 5.5 5.2 4.9 4.7 4.5 4.3 4.1 3.9 3.7 3.6 3.4 6.8 46

29 11.3 10.2 9.2 8.4 7.8 7.2 6.7 6.3 5.9 5.5 5.2 4.9 4.7 4.4 4.2 4.0 3.8 3.6 3.5 3.3 3.2 3.0 6.4 47

30 11.7 10.4 9.3 8.4 7.7 7.1 6.5 6.1 5.7 5.3 5.0 4.7 4.4 4.2 3.9 3.7 3.5 3.4 3.2 3.0 2.9 2.8 2.6 6.1 48

31 10.8 9.5 8.5 7.7 7.0 6.5 6.0 5.5 5.1 4.8 4.5 4.2 4.0 3.7 3.5 3.3 3.1 3.0 2.8 2.7 2.5 5.7 49

32 11.6 10.0 8.8 7.8 7.1 6.4 5.9 5.4 5.0 4.6 4.3 4.0 3.8 3.5 3.3 3.1 2.9 2.8 2.6 2.5 5.4 50

33 10.7 9.2 8.1 7.2 6.5 5.9 5.4 4.9 4.5 4.2 3.9 3.6 3.4 3.2 3.0 2.8 2.6 5.1 51

34 11.9 9.9 8.5 7.5 6.6 5.9 5.4 4.9 4.5 4.1 3.8 3.5 3.3 3.0 2.8 2.6 2.5 4.8 52

35 11.1 9.2 7.9 6.9 6.1 5.5 4.9 4.5 4.1 3.7 3.4 3.2 2.9 2.7 2.5 4.5 53

36 10.3 8.6 7.3 6.4 5.6 5.0 4.5 4.1 3.7 3.4 3.1 2.8 2.6 4.2 54

37 9.6 8.0 6.8 5.9 5.2 4.6 4.1 3.7 3.3 3.0 2.8 2.5 4.0 55

38 11.3 9.0 7.4 6.3 5.4 4.8 4.2 3.8 3.4 3.0 2.7 2.5 3.7 56

39 10.6 8.4 6.9 5.8 5.0 4.4 3.9 3.4 3.1 2.7 2.5 3.5 57

40 10.0 7.8 6.4 5.4 4.6 4.0 3.5 3.1 2.8 2.5 3.3 58

41 9.3 7.3 6.0 5.0 4.3 3.7 3.2 2.8 2.5 3.1 59

42 8.8 6.8 5.6 4.6 3.9 3.4 2.9 2.6 2.9 60

43 11.5 8.2 6.4 5.2 4.3 3.6 3.1 2.7 2.7 61

44 10.9 7.7 6.0 4.8 4.0 3.3 2.8 2.5 62

45 10.3 7.3 5.6 4.5 3.7 3.1 2.6

46 9.7 6.8 5.2 4.2 3.4 2.8

47 9.2 6.4 4.9 3.9 3.1 2.6

48 8.7 6.1 4.6 3.6 2.9

49 8.2 5.7 4.3 3.3 2.7

50 7.8 5.4 4.0 3.1 2.5

These drivers may

not work well with

these enclosures

ONE YEAR LIMITED WARRANTY

Ai Research warrants to the original retail purchaser, this

product to be free from defective workmanship and material

when used under normal conditions in accordance with the

product's printed instructions for a period of one (1) year from

date of purchase. Ai Research agrees to remedy any such

defect or to furnish a new part in exchange for the defective one

at no charge for parts or labor.

This warranty is limited to Ai Research products and specifically

excludes consequential damage to other associated equipment

which may result for any reason from use with this product. In

no event shall Ai Research be liable for incidental or

consequential damages or have any liability with respect to

defects other than the obligations set forth above. Some states

do not allow limitations on how long an implied warranty lasts,

and/or the exclusion or limitation of incidental or consequential

damages, so the above limitations or exclusions may not apply

to you. This warranty gives you specific rights and you may

also have other rights which vary from state to state.

This warranty does not cover the following:

• Damages caused by water, neglect, abuse, misuse,

• Improper installation or operation.

• Damages caused by acts of God or nature.

• Damages occurring during shipment of the product to

Ai Research for repairs.

• Any product which is modified without consent of Ai

Research.

If you need warranty service, take the following steps:

1.Save your sales receipt for warranty registration and service.

2.Contact the dealer from whom you bought Q-Logic. They will

give you instructions for warranty service.

3.If no dealer is available, call Ai Research for further

Instructions: (405) 624-6722. You must receive an RA#

before returning any defective parts.

SHIPPING ADDRESS:

Ai Research

2805 E. 6th

Stillwater, OK

74074-6513

This ruler is calibrated in tenths for your convenience.

QLH/T-1.2512sx/dx PORT TUNING CHART

No trimming

required for

these drivers

Step 3-B:

1. Round the VAS value for your woofer up to the higher of the closest values on the chart.

2. Look up the intersection of Fs and VAS for the woofer you wish to use. This number is the port

length in inches.

3. Many driver configurations will NOT REQUIRE PORTS. Please refer to your specific driver's

recommendations.

4. Using the port length from above, refer to the Port Tuning Frequency Chart to determine the

roll-off point of your system. IF THIS FREQUENCY IS GREATER THAN Fs, THE DRIVER MAY

PERFORM BETTER IN A SEALED ENCLOSURE! If satisfactory, proceed to step 5. If not, you

may want to consider a different driver, or leaving the enclosure sealed ( unported).

Consult your dealer if you are unsure about your particular application.

5. Cut all of the ports for your enclosure to the length on the chart.

6. These Q-Logic enclosures have a port plug installed from inside the enclosure.

7. When porting these enclosures you will need to remove this plastic port plug. (Do not cut the

carpet until step 10)

8. From inside the enclosure, unscrew the four screws holding the port plug in.

9. From the outside of the enclosure firmly press the plug in until it releases.

10. After the port plug and plug gasket are removed, "X" cut the carpet over the hole.

( NOTE: Do not cut the carpet out! )

11. The "X" cut in the carpet will allow the carpet to extend into the port hole and work like a

gasket for the port.

12. Push the "X" cut carpet down into the port hole. Slide your cut and tuned port into

the port hole.

13. Return to step 3-C on front page now.

For other cool

Q-Logic products,

Visit our website!

http://qlogic.ws

32901

Rockford Fosgate Punch Z RFZ3410 Installation & Operation Manual

Rockford Fosgate Punch Z RFZ3410 Installation & Operation Manual

Rockford Fosgate Punch Z RFZ3410 Installation & Operation Manual

Other documents