Marantec Comfort 520 Control x.51 Owner's manual

Comfort 520 / Control x.51

Operator system for Hinged Gates

GB

Manual for installation and operation

1. Meaning of symbols

Caution!

Danger of personal injury!

The following safety advice must

be observed at all times so as to avoid

personal injury!

Attention!

Danger of material damage!

The following safety advice must

be observed at all times so as to avoid

material damage!

Advice / Tip

Check

Reference

i

Photocell or closing edge safety device (CESD)

Gate position OPEN

Has no function

Gate position CLOSED

Reference control point

Has no function

Impulse

(remote control, external control elements)

Operation

Closing edge safety device

STOP

External control elements

Modular antenna

Controls and motor unit symbols Advice

Type plate on motor unit 2 (only double wing)

Type: ________________________________________________

Art. No.: _____________________________________________

Product No.: __________________________________________

Type plate on motor unit 1

Type: ________________________________________________

Art. No.: _____________________________________________

Product No.: __________________________________________

Type plate on control unit

Type: ________________________________________________

Art. No.: _____________________________________________

Product No.: __________________________________________

2 Manual for installation and operation, Comfort 520 GB (#83591)

2. Table of contents

1. Meaning of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

2. Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

3. General safety advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

4. Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

4.1 Comfort 520 supply package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

4.2 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

4.3 Gate variations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

5. Preparation for mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

5.1 General notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

5.2 Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

5.3 Cabling layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

6. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

6.1 Mounting conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

6.2 Installing the motor unit at the gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

6.3 Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

6.4 Fixing the control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

6.5 Connection of control elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

6.6 Connecting the motor unit to the controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

6.7 Connection of the mains cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

7. Hand transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

7.1 Operation and accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

7.2 Hand transmitter coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

8. Initial operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

8.1 Connecting the modular antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

8.2 Overview of the control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

8.3 Overview of the display functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

8.4 Reference point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

8.5 Express programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

8.6 Function test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

9. Extended operator functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

9.1 General notes on extended operator functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

9.2 Programming structure for extended operator functions (Example for Level 2, Menu 2) . . . . . . . . . . . . .38

9.3 General overview of the programmable functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

9.4 Functions overview for the levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

10. Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

10.1 Status messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

10.2 Fault messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

10.3 Rectifying faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

11. Attachment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

11.1 Connection diagram Comfort 520 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

11.2 Technical Data for Comfort 520 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

11.3 Manufacturer’s Declaration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

11.4 EC Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

Manual for installation and operation, Comfort 520 GB (#83591) 3

Please read carefully!

Target group

This operator system may only be installed, connected and put into operation by qualified and trained professionals!

Qualified and trained specialist personnel are persons

- who have knowledge of the general and special safety regulations,

- who have knowledge of the relevant electro-technical regulations,

- with training in the use and maintenance of suitable safety equipment,

- who are sufficiently trained and supervised by qualified electricians,

- who are able to recognise the particular hazards involved when working with electricity,

- with knowledge regarding applications of the EN 12635 standard (installation and usage requirements).

Warranty

For an operations and safety warranty, the advice in this instruction manual has to be observed. Disregarding these

warnings may lead to personal injury or material damage. If this advice is disregarded, the manufacturer will not be

liable for damages that might occur.

Batteries, fuses and bulbs are excluded from warranty.

To avoid installation errors and damage to the gate and operator system, it is imperative that the installation

instructions are followed. The system may only be used after thoroughly reading the respective mounting and

installation instructions.

The installation and operating instructions are to be given to the gate system user, who must keep them safe.

They contain important advice for operation, checks and maintenance.

This item is produced according to the directives and standards mentioned in the Manufacturer's Declaration and in

the Declaration of Conformity. The product has left the factory in perfect condition with regard to safety.

Power-operated windows, doors and gates must be checked by an expert (and this must be documented) before they

are put into operation and thereafter as required, but at least once a year.

Correct use

The operator system is designed exclusively for opening and closing hinged doors and gates.

Gate requirements

The short version operator system - Comfort 520 is suitable for:

- hinged doors and gates with a gate wing width of 3 m and a gate wing weight of 400 kg.

The long version operator system - Comfort 520 L is suitable for:

- hinged doors and gates with a gate wing width of 4 m and a gate wing weight of 400 kg.

Beside the advice in these instructions, please observe the general safety and accident prevention regulations!

Our sales and supply terms and conditions are effective.

3. General safety advice

4 Manual for installation and operation, Comfort 520 GB (#83591)

Information on installing the operator system

• Ensure that the gate is in good mechanical condition.

• Ensure that the gate opens and closes properly.

• Remove all unnecessary components from the gate (e.g. cables, chains, brackets).

• Render any installations inoperable that will no longer be needed after the operator system has been installed.

• Before commencing cabling works it is very important to disconnect the operator system from the electricity supply.

Ensure that the electricity supply remains disconnected throughout the cabling works.

• Adhere to the local protection regulations.

• Lay the electricity supply cables and control cables; these MUST be laid separately. The controls voltage is 24 V DC.

• Install all the impulse transmitters and control devices (e.g. remote control buttons) within sight of the gate and at a

safe distance from the moving parts of the gate. A minimum installation height of 1.5 m must be observed.

• Ensure that no part of the gate extends across public footways or roads when the installation is complete.

Information on commissioning the operator system

After initial operation, the persons responsible for operating the gate system, or their representatives must be

familiarised with the use of the system.

• Make sure that children cannot access the gate control unit.

• Before moving the gate, make sure that there are neither persons nor objects in the operating range of the gate.

• Test all existing emergency command devices.

• Never insert your hands into a running gate or moving parts.

• Pay attention to any parts of the gate system that could cause crushing or shearing damage or accidents.

The EN 13241-1 regulations must be observed.

Information on servicing the operator system

To ensure proper operation, the following items must be checked regularly and repaired if necessary.

Before any works to the gate system are undertaken, the operator system must be disconnected from the mains.

• Check once a month that the operator system stops and reverses in every position when the gate touches an

obstacle. Place an obstacle in the path of the gate to check this.

• Check the settings of the OPEN and CLOSE automatic cut-out function.

• Check all movable parts of the gate and operator system.

• Check the gate system for signs of wear or damage.

• Check whether the gate can be easily moved by hand.

Information on cleaning the operator system

Never use water jets, high pressure cleaners, acids or bases for cleaning.

Please read carefully!

3. General safety advice

Manual for installation and operation, Comfort 520 GB (#83591) 5

6 Manual for installation and operation, Comfort 520 GB (#83591)

4.1 Comfort 520 supply package

4. Product overview

4.1 / 1

1

2

Single wing gate system

(Short version – Comfort 520)

1 Motor unit with short connection cable (1.2 m)

2 Key (2x)

4.1 / 2

1

2

Single wing gate system

(Long version – Comfort 520 L)

1 Motor unit with short connection cable (1.2 m)

2 Key (2x)

4.1 / 3

3 Motor unit with short connection cable (1.2 m)

4 Motor unit with long connection cable (9.5 m)

5 Key (4x)

Double wing gate system

(Short version – Comfort 520)

3

4

5

4.1 / 4

3 Motor unit with short connection cable (1.2 m)

4 Motor unit with long connection cable (9.5 m)

5 Key (4x)

Double wing gate system

(Long version – Comfort 520 L)

3

4

5

The Comfort 520 standard delivery package comprises:

- motor unit

- controls

- fixing materials for controls

and motor unit

- remote control

The Comfort 520 is available in the following versions,

as required:

4. Product overview

Manual for installation and operation, Comfort 520 GB (#83591) 7

!#

!¯

!Ø

!”

8

9

4.1 / 5

6 Control x.51

7 Handle

4.1 / 6

8 Screws 3.5 x 32 (4x)

9 Wall plugs S6 (4x)

10 Spacer elements (2x)

11 Screw fixing insert with 2 flat cable openings

12 M20 screw fixing with flat cable insert

13 M20 screw fixing with round cable insert

14 M16 screw fixing with round cable insert

Control unit

Mounting kit for control unit

6

4.1 / 7

15 Wood screws 8 x 60 (4x)

16 Wall plugs S10 (4x)

17 Gate bracket

(short or long version)

18 Cover cap (3x)

19 M8 x 25 (6x)

20 Nuts M8 (6x)

21 Post bracket

Single wing gate system installation set

!£

!5

!˜

!^

!\

!·

„¯

7

„Ø

8 Manual for installation and operation, Comfort 520 GB (#83591)

4.1 / 10

22 Hand transmitter

23 Sun visor clip

24 Module antenna

25 Transmission plug

Remote control

„”

„#

„£

„5

4. Product overview

15 Wood screws 8 x 60 (8x)

16 Wall plugs S10 (8x)

17 Gate bracket (2x)

(short or long version)

18 Locking plates (6x)

19 M8 x 25 (12x)

20 Nuts M8 (12x)

21 Post bracket (2x)

Double wing gate system installation set

!5

!˜

!^

!\

!·

„¯

„Ø

!5

!˜

!^

!\

!·

„¯

„Ø

4.1 / 8

4.1 / 9

Manual for installation and operation, Comfort 520 GB (#83591) 9

4. Product overview

4.3 / 1

The standard supply package is suitable for

the following types of gate.

Single wing gate system

4.3 / 2

Double wing gate system

4.3 Gate variations

4.2 / 1

Short version – Comfort 520

4.2 / 2

Long version – Comfort 520 L

4.2 Dimensions

78

428

72

74

120

358

633

811

114

ø12

ø10

M8

52,5

78

548

72

74

120

478

753

931

114

ø12

ø10

M8

52,5

10 Manual for installation and operation, Comfort 520 GB (#83591)

5.2 Checks

Attention!

In order to guarantee correct

mounting, carry out the following

checks before installing.

Supply package

• Check the package to ensure that all the parts are

included.

• Check that you have all the additional components

that are necessary for your particular installation

requirements.

Gate system

• Ensure that your gate system has an appropriate

electricity supply connection and a facility

for disconnecting the mains. The minimum

cross-sectional area of the earth cable is

3 x 1.5 mm

2

.

• Ensure that all cables are suitable for outdoor use

(UV resistant and cold resistant).

• Ensure that your gate system has a gate stop in the

CLOSE and OPEN directions.

• Disassemble the door latches or render them

inoperable.

• Ensure that the gate can be easily moved by hand.

• Observe the following gate requirements.

Gate wing width:

- Comfort 520 min. 1 m - max. 3 m

- Comfort 520 L min. 1 m - max. 4 m

Gate height: max. 2.5 m

Gate wing weight: max. 400 Kg

Open space: min. 50%

Gate incline: with accessories, max. 10%

(approx. 10 cm/m)

5. Preparation for mounting

5.1 General notes

The pictures in these instructions are not true-to-scale.

Dimensions are always given in millimetres (mm)!

The motor unit and the controls must be mounted on

the inside of the gate system.

For correct mounting you will need the following

tools:

13

ø 10

ø 6.5

13 2

2

5

M 8

ø 6

5.1 / 1

Advice:

The use of an electric lock is

recommended for a gate wing

wider than 2 m.

Manual for installation and operation, Comfort 520 GB (#83591) 11

5. Preparation for mounting

5.3 Cabling layout

5.3 / 1

2 x 0.75 mm

2

8 x 0.75 mm

2

8 x 0.75 mm

2

2 x 0.4 mm

2

2 x 0.4 mm

2

2 x 0.4 mm

2

2 x 0.4 mm

2

3 x 1.5 mm

2

230 V / AC

3 x 1.5 mm

2

Advice:

This is just an example of a cabling layout; the layout can vary according to the type of gate and the

associated equipment.

Reference:

The relevant instructions are to be followed for the installation and cabling of the gate sensors and

the operating and safety elements.

i

1 Photocell

2 Photocell

3 Signal light

4 Code button, transponder, ...

5 Key switch

6 Mains isolator switch (mains disconnection facility)

7 Electric lock

8 Stop plate

9 Mains supply cable

10 Closing edge safety device (CESD)

2

23

4

6

9

7

1

8

!¯

5

12 Manual for installation and operation, Comfort 520 GB (#83591)

6.1 Mounting conditions

6. Installation

The mounting positions of the gate bracket (C) and

the post bracket (D) are dependent on the current gate

situation.

The positions of the gate bracket (C) and the post bracket

(D) influence the following factors:

- Opening angle (n)

- Utilisation of the movement stroke (m)

- Gate travelling speed

A triangle of forces is formed by the gate pivot (A),

the post bracket pivot (B) and the gate bracket pivot (I).

6.1 / 1

C

B

D

A

n

m

E

6.1 / 2

Motor unit is parallel to the gate

6.1 / 3

Motor unit is in triangle of forces

Attention!

For trouble-free operation, choose the

positions of the brackets such that they

meet all following conditions:

- The motor unit must be located in a

triangle of forces and should not be

parallel to the gate at the OPEN and

CLOSED gate positions.

- The length of travel should be as

large as possible.

Manual for installation and operation, Comfort 520 GB (#83591) 13

6. Installation

6.1 / 4 6.1 / 5

D

F

A

Advice:

For hinged gates with a negative e value of 0 to -80 mm, the “Special 502” bracket extension must be

used (not included in the standard package).

Find dimension e

e

The type of post bracket required can be determined from dimension e.

e Distance from post bracket screw-plate to the gate pivot

A Gate pivot

F Screw plate of post bracket

Positive e value (Illustration 6.1 / 4)

The pivot (A) lies behind the screw-plate (F) of the post bracket (D).

The installation can be carried out using the components in the standard package.

Negative e value (Illustration 6.1 / 5)

The pivot (A) lies in front of the screw-plate (F) of the post bracket (D).

F

14 Manual for installation and operation, Comfort 520 GB (#83591)

6. Installation

Long version – Comfort 520 L

e = 100 - 200 mm / max. gate wing width 4 m / max. gate wing weight 400 kg

Short version – Comfort 520

e = 0 - 100 mm / max. gate wing width 3 m / max. gate wing weight 400 kg

6.2 / 1

f

C

x

A

e

B

D

e f x A B B1 1.BR 2.BR

0 f~e 20 - 50 125 122 500 x

25 f~e 20 - 50 125 147 500 x

50 f~e 20 - 50 125 172 500 x

75 f~e 20 - 50 130 162 510 x

100 f~e 20 - 50 130 187 510 x

e f x A B B1 1.BR 2.BR

100 f~e 20 - 50 200 222 560 x

125 f~e 20 - 50 195 212 570 x

150 f~e 20 - 50 195 237 570 x

175 f~e 20 - 50 180 262 575 x

200 f~e 20 - 50 170 287 585 x

D

2.BR

1.BR

Advice:

The information on the table is valid for an opening angle of 90°.

Tables of measurements

With the help of the dimension tables, the approximate position of the gate bracket (C) and the post bracket (D) at the

gate can be determined.

6.2 Installing the motor unit at the gate

B1

Manual for installation and operation, Comfort 520 GB (#83591) 15

6. Installation

6.2 / 2

• Determine the fixing points which are suitable for

your gate configuration by means of the table of

measurements.

• Align the angles horizontally.

• Fix the angles with screw clamps.

6.2 / 3

• Release the motor unit.

• Place the motor unit on the bracket.

6.2 / 4

Reference:

The motor unit release function is

described under 6.3.

i

• Open the gate up to the desired opening angle.

Tip:

For an easier determination of the

fixing points you can use the optional

mounting pattern for Comfort 520 or

Comfort 520 L.

16 Manual for installation and operation, Comfort 520 GB (#83591)

6. Installation

If all mounting conditions are correct, the positions of

the angles are defined.

If the mounting conditions are not correct, adjust the

gate travel.

6.2 / 5

The following alterations can be made to adjust the

travel of the gate.

- Select a different drill hole on the gate bracket (C)

and/or on the post bracket (D).

- Alter the horizontal position of the gate bracket.

- Alter the horizontal position of the post bracket.

• Adjust the gate travel in such a way that all the

mounting conditions are met.

M8 x 25

• Remove the motor unit from the angles.

• Lock the motor unit.

• Mark the drill hole locations on the gate and on the

post.

• Remove the screw clamps.

• Screw the gate bracket (C) to the gate at the

calculated position.

Reference:

The mounting conditions can be found

in chapter 6.1.

i

6.2 / 6

DC

C

Manual for installation and operation, Comfort 520 GB (#83591) 17

6. Installation

• Screw the post bracket (D) to the pillar at the

calculated position.

8 x 60

Mounting on a concrete or stone pillar

Mounting on a metal post

M8 x 25

• Screw the post bracket (D) to the post at the

calculated position.

M8

For double wing gate systems, the motor unit with the

short connection cable must be mounted on the same

side as the controls.

• Set the motor unit in the calculated drill holes in the

gate bracket and in the post bracket.

• Screw the motor unit tightly onto the angles.

• Push the cover caps (E) into the redundant drill holes

from above.

• For double wing gate systems, fix the second motor

unit accordingly on the other side.

6.2 / 8

6.2 / 9

E

Caution!

To avoid injuries, the drill holes in the

post bracket that are not required must

be fitted with cover caps (E).

6.2 / 7

D

18 Manual for installation and operation, Comfort 520 GB (#83591)

6. Installation

6.3 Release

Releasing

• Open the protective cap.

• Put the key into the lock and turn it 90° clockwise.

Locking

• Push the unlocking lever (A) up.

Attention!

The gate must be relocked in

the same position, in which it was

released!

Attention!

The releasing position of the gate must

be marked in order to ensure correct

locking.

6.3 / 1

6.3 / 2

6.3 / 3

6.3 / 4

• Push the unlocking lever (A) down.

The drive is now mechanically disconnected and the

gate can be moved by hand.

• Put the key into the lock and turn it 90° anticlockwise.

• Close the protective cap.

The drive is now mechanically connected and the gate

can be moved via the motor unit.

A

6. Installation

Manual for installation and operation, Comfort 520 GB (#83591) 19

6.4 / 1

• Open the control unit.

• Mount the control unit using the spacer elements (A).

3.5 x 32

Attention!

The control unit must be installed in

such a way that the motor cable can be

fed through the screw fixing at the

base of the control unit.

6.4 / 2

A

6.5 Connection of control elements

Attention!

In order to avoid damaging the

controls:

- The local safety regulations must be

complied with at all times.

- It is very important that mains cables

are laid separately from control cables.

- The controls voltage must be 24 V DC.

- If external voltages are applied at

terminals XM70A, XV51A, XM70B,

XV51B, XB99, XP54B, XP54A, XP62B,

XP62A or XB70, the entire electronic

system will be destroyed.

- Only potential-free contacts may be

connected to terminals B9, 5, 34, 3

and 8 (XB99).

Caution!

Danger of electric shock:

Before any cabling works begin, it must

be ensured that the cables are

disconnected from the power supply.

During cabling works, it must be

ensured that the cables remain

disconnected from the power supply at

all times (e.g. prevent reconnection).

P

1

2

3

4

5

6

7

8

1

2

L

N

PE

15

16 17

6.5 / 1

XN81

XV51B

XM70B

XM70A

XV51A

XB99

XP54A

XB70

XP54B

XH01

XP62A

XP62B

6.4 Fixing the control unit

6. Installation

Reference:

When installing external control

elements, or safety and signal

equipment, the relevant instructions

must be observed.

i

Label Type / function

i

XB70 Connection of modular antenna 8.1

XB99

Connection of external control

elements

6.5 / 2

6.5 / 3

6.5 / 4

6.5 / 5

XH01

Connection for programmable

output 16/17 (e.g. signal light,

24 V DC, 0,5 A)

Wiping impulse 15/16

6.5 / 6

6.5 / 7

XM70A

Connection for motor unit

(MASTER)

6.6 / 5

6.6 / 8

XM70B

Connection for motor unit

(SLAVE)

6.6 / 5

6.6 / 8

XN81 Connection for mains cable

6.5 / 6

6.7

XP54A

Connection for closing edge

safety device, gate travelling

direction CLOSE

6.5 / 8

XP54B

Connection for closing edge

safety device, gate travelling

direction OPEN

6.5 / 8

XP62A

Connection for photocell,

gate travelling direction CLOSE

6.5 / 9

XP62B

Connection for photocell,

gate travelling direction OPEN

6.5 / 9

XV51A

Connection for rpm detector

and reference point sensor

(MASTER)

6.6 / 5

6.6 / 8

XV51B

Connection for rpm detector

and reference point sensor

(SLAVE)

6.6 / 5

6.6 / 8

Terminal XB99

Factory settings:

B9 and 5 bridged

Connection option 1:

-XB99

B9 5 34 3 8

-SB5

12 11

-SB8

14 13

-XB99

B9 5 34 3 8

6.5 / 2

6.5 / 3

M06E039

20 Manual for installation and operation, Comfort 520 GB (#83591)

Page is loading ...

Marantec Comfort 520 Control x.51 Owner's manual

Marantec Comfort 520 Control x.51 Owner's manual

Related papers

Other documents