LG PRCKD21E.ENCXLAR Installation guide

Type
Installation guide

This manual is also suitable for

개정일자 :
QA 요청사항 :
바코드와 P/No.가 일치하는가? (바코드 확인)
언어표시띠의 위치(누락여부)는 바른가?
약물(기호)이 깨지거나 위치가 어긋 난 곳은 없는가?
그림이 가려지거나 잘려나간 곳은 없는가?
KUKJE-334
문서번호
CWROM-1606-00630
Order No.
MFL62049616
P/No.
최종 컨펌일자 :
작업자
연구실 담당자
2016-6-28
오후1:07:45
작업원고와 수정내용이 일치하는가?
* 필수확인 - QA요구사항
*최종 확인후 본 체크리스트는 삭제됩니다.
1. 원고에 지시된 대로 작업한 후 이상없이 작업 되었는지 재차 검토 후 PDF 파일을 생성한다.
2. 작업완료 후 담당 연구원에게 수정부분에 대한 검증요청한다.
(*** 반드시 필요 – 의뢰자가 요청한 의도대로 작업이 정확히 되었는지 반드시 확인이
필요함)
3. 아래 체크리스트에 따라 놓치기 쉬운 사항을 우선으로 한번 더 확인한다.
2016-6-1
P/NO : MFL62049616
INSTALLATION MANUAL
MODELS : PRCKD21E
PRCKD41E
AHU
CONTROL KIT
www.lg.com
Please read this installation manual completely before installing the product.
Installation work must be performed in accordance with the national wiring
standards by authorized personnel only.
Please retain this installation manual for future reference after reading it
thoroughly.
ENGLISH
ESPAÑOL
• Do not cool excessively indoors. This may be harmful for your health and may consume more
electricity.
• Block sunlight with blinds or curtains while you are operating the air conditioner.
• Keep doors or windows closed tightly while you are operating the air conditioner.
• Adjust the direction of the air flow vertically or horizontally to circulate indoor air.
• Speed up the fan to cool or warm indoor air quickly, in a short period of time.
• Open windows regularly for ventilation as the indoor air quality may deteriorate if the air condi-
tioner is used for many hours.
• Clean the air filter once every 2 weeks. Dust and impurities collected in the air filter may block the
air flow or weaken the cooling / dehumidifying functions.
For your records
Staple your receipt to this page in case you need it to prove the date of purchase or for warranty
purposes. Write the model number and the serial number here:
Model number :
Serial number :
You can find them on a label on the side of each unit.
Dealer’s name :
Date of purchase :
Here are some tips that will help you minimize the power consumption when you use the air
conditioner. You can use your air conditioner more efficiently by referring to the instructions
below:
TIPS FOR SAVING ENERGY
2
ENGLISH
TIPS FOR SAVING ENERGY
3
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
Always comply with the following precautions to avoid dangerous situations and ensure peak
performance of your product.
WARNING
It can result in serious injury or death when the directions are ignored.
CAUTION
It can result in minor injury or product damage when the directions are ignored.
WARNING
• Installation or repairs made by unqualified persons can result in hazards to you and others.
• The product shall be installed according to the Wiring regulations of the corresponding coun-
try.
• The information contained in the manual is intended for use by a qualified service technician
familiar with safety procedures and equipped with the proper tools and test instruments.
• Failure to carefully read and follow all instructions in this manual can result in equipment mal-
function, property damage, personal injury and/or death.
Installation
• The electrical work shall be performed by the technician with qualification according to Electric Facil-
ity Technical Standard and this installation manual, and the specified circuits must be used.
- If power capacity is inadequate or if the electrical work is defective, it may cause fire or electric
shock.
• Make sure to perform the grounding work.
- If it is not grounded, it may cause electric shock.
• Make sure to install leakage current breaker and exclusive switch.
- If they are not installed, it may cause fire or electric shock.
• Do not use damaged leakage current breaker or switch.
- It may cause fire or electric shock.
• System air conditioner installation can only be performed by the specialty store with system air con-
ditioner installation license.
- Inadequate installation may cause water leakage, fire, or electric shock.
• During the relocation or re-installation of the product, request to MULTI V AHU installation specialty
store.
- Inadequate installation may cause water leakage, fire, or electric shock.
• Do not disassemble, repair, or modify the product without authorization.
- It may cause fire or electric shock.
• Do not keep or use combustible gas or inflammable material near the product.
- It may cause fire or product disorder.
• Please use the circuit breaker and fuse with the specified capacity.
- If a circuit breaker or fuse above the specified capacity or steel or copper wire is used, it may
cause overall product disorder or fire.
!
!
!
• Do not twist or damage the power cable.
- It may cause fire or electric shock.
• During the electric work, request to the specialty store where you purchased the product or the
service center.
- If you disassemble or repair without authorization, it may cause fire or electric shock.
• During the opening of the package or installation, be careful not to touch the sharp parts.
- Otherwise, it may cause injury.
• During the product installation, make sure to request the service center or installation specialty
store.
- It may cause fire or electric shock.
• The product shall be installed in the designated place using the designated installation material.
- It may cause disorder.
• Do not install the product outside.
- It may cause disorder or electric shock.
Operation
• Do not change or extend the power cable without authorization.
- It may cause fire or electric shock.
• Please use the power cable exclusive for the product.
- It may cause fire or electric shock.
• Do not let water enter inside the product (control part). Especially, do not wash the product with
water.
- It may cause electric shock or disorder.
• When you turn off the main power switch, do not touch it with wet hand.
- It may cause fire or electric shock.
• When the product is flooded, make sure to contact MULTI V AHU installation specialty store.
- It may cause fire or electric shock.
• If there is an abnormal sound, odor, or smoke from the product, or during the black out, turn off the
main power switch.
- Otherwise, it may cause fire or electric shock.
• Do not place an heavy object on the power cable.
- It may cause fire or electric shock.
• Do not let a worker or user climb up on the product.
- They may fall and get severe injury.
• Do not use a heating product near the power cable.
- It may cause fire or electric shock.
• If the product is not used for a long period of time, turn off the main power switch.
- It may cause fire or disorder.
• During the product operation, do not turn off the product with the main power switch.
- It may cause fire or electric shock.
IMPORTANT SAFETY INSTRUCTIONS
4
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
5
ENGLISH
CAUTION
Installation
• Do not install in a place with leakage of combustible gas.
- If it is installed in a place with leakage of combustible gas, it may cause property damage.
• If it is installed in a place like hospital, communication station, etc., provide sufficient protection facil-
ity for noise.
- Inverter equipment, personal generator, high frequency medical equipment, and electronic commu-
nication equipment may cause abnormal operation or disorder of the product. On the other hand,
the product may cause noise or have effect that disturbs the medical equipment or video broad-
casting.
• Do not let children touch the product.
- Improper operation by children may cause disorder of the product or electric shock.
Cautions during electrical work or transportation
• Install without tension in the power cable.
- If a tension is imposed, the cable may snap or heat can be generated to cause fire. If the power
cable is damaged, do not replace it by yourself, but call A/S center for replacement.
• Use the exclusive cable for the product. Use the rated power cable with the sufficiently permitted
current.
- It may cause fire or electric shock.
• Be careful during the transportation of the product.
- Do not carry the product of 20kg or heavier. It may cause injury.
• Dispose the packaging material safely.
- The metal packaging material such as nails or wooden packaging material may cause stab or other
injury.
- Rip the plastic or vinyl packaging envelope, etc. and dispose in a safe place to prevent children
from playing with them. If the children play with the vinyl envelopes that are not ripped, it may
cause suffocation.
!
6
TABLE OF CONTENTS
ENGLISH
2 TIPS FOR SAVING EN-
ERGY
3 IMPORTANT SAFETY IN-
STRUCTIONS
7 INSTALLATION COMPO-
SITION
7 Installation composition diagram
7 Cautions during the composition of the
installation
8 PRODUCT COMPOSI-
TION
8 Basically provided parts
8 Sensor (separately sold)
9 ACCESSORY
9 Product composition diagram
10 PRODUCT DIMENSION
11 WIRING DIAGRAM
11 Part positioning diagram
15 INSTALLATION FLOW-
CHART
16 CONTROL KIT INSTAL-
LATION
16 Product installation location verification
17 Product installation
18 CONTROL KIT outdoor box installation
19 PIPE TEMPERATURE
SENSOR CONNECTION
20 OUTDOOR UNIT COM-
MUNICATION LINE CON-
NECTION
21 CAUTIONS
22 AHU SENSOR SPECIFI-
CATION
23 AHU SENSOR COVER IN-
STALLATION(FOR OUT-
SIDE INSTALLATION)
24 AHU SENSOR CONNEC-
TION
31 ACP/BACNET GATEWAY
CONNECTION
32 ROTARY SWITCH SET-
TING
35 AHU CONTROLLER SET-
TING
38 COMMUNICATION PCB
SETTING
40 ELECTRICAL CONNEC-
TION WORK
44 Cautions
45 TEST OPERATION
45 Check list before test operation
45 Cautions
46 Wired remote controller
47 Wired remote controller installation
method
48 SELF DIAGNOSIS FUNC-
TION
48 Error display
48 Error display method
49 Error display(AHU)
50 Example of error occurrences
50 Error occurrence order
TABLE OF CONTENTS
INSTALLATION COMPOSITION
7
ENGLISH
SA
MCC
3
5
9
1
4
6
7 -1 7 -2
8 -2
8 -18 -1
2
220 V~, 60 Hz
220-240 V~, 50 Hz
RA EA OA
Cautions during the composition of the installation
- MCC requires facility work by facility company, and carry out a separate discussion before the
installation.
- Temperature or temperature and humidity sensor must be installed in SA/RA to be operated
properly.
Installation components
No.
Category Applied specification
¿
Air handling unit -
¡
Control kit PRCKD21E/41E
¬
Expansion kit unit PATX13A0E/20A0E/25A0E/35A0E/50A0E
Outdoor unit MULTI V
ƒ
Pipe temperature sensor IN
Sensor: Ø5, length: 10 m, cable color: Black
Pipe temperature sensor OUT
Sensor: Ø7, length: 10 m, cable color: Red
-1
Temperature and humidity sensor RA
-40 °C ~ 70 °C, RH 0~95 % /
AC 24 V / DC 0~10 V
-
2
Temperature and humidity sensor SA
« -1
Return Fan -
«-
2
Supply Fan -
»
MCC MCC
- RA: Return Air
- EA: Exhaust Air
- OA: Outdoor Air
- SA: Supply Air
Power cable
Refrigerant pipe
Pipe temperature sensor
Signal cable
Communication cable
Refrigerant flow(cooling)
Refrigerant flow(heating)
Installation composition diagram
INSTALLATION COMPOSITION
8
PRODUCT COMPOSITION
ENGLISH
Sensor (separately sold)
- To operate the product properly, the following temperature or temperature and humidity sensor
must be separately purchased and installed.
- The separate specification and installation location of the applied sensor can be verified in ‘AHU
sensor specification’ category.
Category Specification
Temperature sensor
- Power: AC 24 V
- Output signal: DC 0~10 V
- Temperature boundary: -50~50 °C
Temperature and humidity
sensor
- Power: AC 24 V
- Output signal: DC 0~10 V
- Temperature boundary: -40~70 °C
- Humidity boundary: 0~95 % RH
CONTROL KIT
Wired remote
controller
Installation bolt/nut
Installation
manual
Owner’s
manual
Model name
è˜äÍêÎê‘ êcòØ
PRCKD21E
- Quantity: 1EA
- Maximum number
of outdoor units
that can be con-
nected : 4EA
Quantity:
1EA
- Number of bolts:
4EA (M10 / 70 mm)
- Number of nuts:
4EA (M10)
Quantity:
1EA
Quantity:
1EA
PRCKD41E
- Quantity: 1EA
- Maximum number
of outdoor units
that can be con-
nected : 8EA
Quantity:
1EA
P/NO : MFL67476601
www.lg.com
INSTALLATION MANUAL
AIR CONDITIONER
• Please read this installation manual completely before installing the product.
• Installation work must be performed in accordance with the national wiring
standards by authorized personnel only.
• Please retain this installation manual for future reference after reading it
thoroughly.
TYPE : Cooling Only Inverter
ENGLISH
OWNER’S MANUAL
AIR CONDITIONER
Please read this manual carefully before operating
your set and retain it for future reference.
P/NO : MFL67649101
www.lg.com
TYPE : FLOOR STANDING
MODEL : APNQ36GRA0
APUQ36GRA0
ENGLISH
Basically provided parts
PRODUCT COMPOSITION
ACCESSORY
9
ENGLISH
• PRCKD21E/41E
- ( ) is the quantity applied to PRCKD41E model.
No. Part name Specification
Quantity
No. Part name Specification
Quantity
Wired remote controller
- 1
Controller case 1
Door - 1
Fuse
AC 250 V, 5 A
5
Wired remote con-
troller protection box
Polycarbonate, IP65
1
Relay
AC 250 V, 5 A
4
Selection switch ON/OFF 3
Communication PCB
- 2(4)
Lamp
Power/SA/RA/
Inspection lamp
4
Communication
PCB case
2(4)
Transformer
Input: AC 220 V
Output: AC 24 V
Capacity: 50 VA
1
Control box 1.6 T 1
Controller protection box
0.8 T 1
Adapter
DC 12 V, 3.33 A
1
Terminal block A 15 A x 1.25 mm
2
2
Adapter case - 1
Terminal block B 20 A x 1.25 mm
2
1
Poly fuse PCB - 1
Circuit breaker for
wiring
15 A 1
Poly fuse PCB
bracket
0.8 T 1
AHU controller - 1
(PRCKD41E application)
Product composition diagram
ACCESSORY
10
PRODUCT DIMENSION
ENGLISH
BE
4-Ø16 hole
<Bottom side>
<Side> <Front side> <Back side>
A
FH G F
CD
CAUTION
The cables entering F/G/H hole may be different according to the installer, and use the
flexible pipe and connector that fit the corresponding hole.
PRCKD21E/PRCKD41E Remark
A (mm) 600 Length
B (mm) 750 Height
C (mm) 280 Width
D (mm) 510
AHU locking hole
E (mm) 650
F 4-Ø16 hole Pipe sensor insertion part
G 10-Ø25 hole
Sensor/communication line insertion part
H Ø30 hole Power cable insertion part
Weight
(kg)
Product 43.5 Product weight
Packaging 48 Weight after packaging
!
PRODUCT DIMENSION
WIRING DIAGRAM
11
ENGLISH
AHU Controller part
AHU Controller part
Terminal block part #1
Terminal block part #1
Terminal block part #2
Terminal block part #2
Safety parts
Safety parts
Communication PCB part #2
Communication PCB part #2
Communication PCB part #1
Communication PCB part #1
AHU Controller part
AHU Controller part
Terminal block part #1
Terminal block part #1
Terminal block part #2
Terminal block part #2
Safety parts
Safety parts
Communication PCB part #2
Communication PCB part #2
Communication PCB part #1
Communication PCB part #1
AHU Controller part
<Inside the product>
Terminal block part #1
Terminal block part #2
Safety parts
Communication PCB part #2
Communication PCB part #1
• PRCKD41E
CAUTION
The cables entering F/G/H hole may be different according to the installer, and use the
flexible pipe and connector that fit the corresponding hole.
!
Part positioning diagram
WIRING DIAGRAM
12
WIRING DIAGRAM
ENGLISH
- FUSE1 : 250 V 3.15 A
1
ON
ON ON
2345678
17 18 19 20 21 22 23 24 9 10 11 12 13 14 15 16
ON ON
ON
• AHU Controller part
• Communication PCB part(PRCKD21E)
WIRING DIAGRAM
13
ENGLISH
220-240 V~, 50/60 Hz
CABLE : OVER CV 2.5 mm
2
- FUSE1 : 250 V 3.15 A
• Communication PCB part(PRCKD41E)
• Safety parts (transformer, short circuit breaker for wiring)
14
WIRING DIAGRAM
ENGLISH
• Terminal block part #1
• Terminal block part #2
INSTALLATION FLOWCHART
15
ENGLISH
CONTROL KIT installation
Pipe temperature sensor
connection
Outdoor unit communication
line connection
AHU sensor connection
• 2 outdoor units can be connected to
communication PCB 1EA, so be careful
not to have mixed connection of the pipe
temperature sensor and communication
line that are connected to 1 outdoor unit.
• You must install temperature/humidity
sensor to SA duct and RA duct that com-
ply with the specification.
(Specification: -40 °C~70 °C,
RH 0~95 % / AC 24 V / DC 0~10 V)
If only temperature sensor is installed to SA/
RA duct, you do not need to set Dip switch.
According to the installation site, set the
Dip switch according to the setting method.
• Be careful of the Dip switch setting accord-
ing to whether outdoor unit is connected.
• During the connection of outdoor unit,
make sure to set all rotary switches to be
different.
• After completing CONTROL KIT installa-
tion, make sure to set outdoor unit
address.
AHU Controller setting
Communication PCB
setting
Electrical wiring
Outdoor unit address
setting
Operation inspection
CAUTION
According to the construction site, this order may be changed, and make sure to study
the installation manual for the corresponding work before the work.
!
INSTALLATION FLOWCHART
16
CONTROL KIT INSTALLATION
ENGLISH
Product installation location verification
- Verify CONTROL KIT installation location in AHU product.
Installation bolt (4EA)
Installation nut (4EA)
Detail
Installation location
(during product side installation)
4 holes
Installation material
4-Ø12 hole
<CONTROL KIT backside>
<AHU>
650 mm
510 mm
- Check the location of the holes at the back of CONTROL KIT and whether there is a material for
installation.
CONTROL KIT INSTALLATION
CONTROL KIT INSTALLATION
17
ENGLISH
Product installation
- Verify CONTROL KIT installation location in AHU product.
<Installation completed>
CAUTION
- Do not install the product by one person. It may cause injury.
- After installation of the product, check if it is fixed properly.
!
18
CONTROL KIT INSTALLATION
ENGLISH
CONTROL KIT outdoor box
installation
Outdoor box installation location verification /
Punching holes
- Verify CONTROL KIT outdoor box installation
location in AHU product and punch the holes.
- Verify the location of the holes at the back of
Outdoor box and if there are installation ma-
terial
Outdoor box / CONTROL KIT installation
- Match the holes punched on the side of AHU
and the holes of outdoor box and fix them
with bolts and nuts (CONTROL KIT enclosed)
and washer(outdoor box enclosed).
- Fix CONTROL KOT inside the installed out-
door box. During the fixing, separate the nut
locked to the bolts inside outdoor box and fix
as follows.
- After completing the installation, verify if it is
composed as follows.
4-Ø12 hole
Nut (4EA)
Bolt (4EA)
Washer
(4EA)
Washer (4EA)
Nut (4EA)
Control Kit
Washer
(4EA)
Reduce the bracket
gap and fix by
tightening
the nuts.
4 holes
<Outdoor box backside>
Product name
Specification
Quantity(EA)
Location
Washer M10, SUS
4
Outdoor box enclosed
Bolt
M10 X 70, SUS
4
Control Kit
enclosed
Nut M10, SUS
4
Washer M10, SUS
4
CAUTION
• Do not install the product by one per-
son. It may cause injury.
• After installation of the product, check if
the bots and nuts are properly fixed.
After installation of the product, adjust the
wire fixing bracket gap at the bottom of
outdoor box to block the wire penetration
space. (Rats, animal, etc. may enter and
damage the electric wires.)
• After installation of the product, verify
the sealed status of AHU and outdoor
box connection part. If there is a defect
in the seal, it may cause leakage.
• If AHU is installed outside, to protect
CONTROL KIT, make sure to install out-
door box.
!
PIPE TEMPERATURE SENSOR CONNECTION
19
ENGLISH
PIPE TEMPERATURE SENSOR CONNECTION
- Check IN/OUT of the pipe temperature sensor connected to EXPANSION KIT.
- Connect flexible pipe and connector (Ø16, supplied from the site) coming from EXPANSION KIT
to CONTROL KIT.
- Classify IN/OUT of pipe temperature sensor and connect to the connectors on communication
PCB.
Flexible pipe and connector: Ø16 (supplied from the site)
Expansion kit (PATX13A0E/
25A0E/35A0E/50A0E)
- Pipe temperature sensor IN :
sensor Ø5, length 10M, cable color Black
- Pipe temperature sensor OUT :
sensor Ø7, length 10M, cable color RED
Pipe temperature sensor IN
Pipe temperature sensor OUT
p@
@CQ@out
p@@@CR@in
Rotary switch #1
EXPANSION KIT #1 EXPANSION KIT #2
Rotary switch #2
p@@@CQ@in
Outdoor unit communication line#2Outdoor unit communication line#1
p@
@CR@out
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

LG PRCKD21E.ENCXLAR Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI