Miller RUNNING GEAR NO. 39 Owner's manual
- Category
- Car kits
- Type
- Owner's manual
This manual is also suitable for
OWNER’S MANUAL
ENGLISHFRAN
Ç
AISESPAÑOL
© 2011 MILLER Electric Mfg. Co.
FORM: OM-224 500D
2011−01
Running Gear No. 39 (300 009)
1. Safety Symbol Definitions
DANGER! − Indicates a hazardous situation which, if not
avoided, will result in death or serious injury. The possible
hazards are shown in the adjoining symbols or explained
in the text.
Wear safety glasses with side shields.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. The possible ha-
zards are shown in the adjoining symbols or explained in
the text.
Tipping equipment can cause injury and damage
equipment. Do not move cart where two wheels are at
different heights and cart could tip − avoid tipping. Be
careful when moving unit over uneven surfaces.
NOTICE
Indicates statements not related to personal injury.
Indicates special instructions.
Cylinders contain gas under high pressure and can ex-
plode if damaged. Never let a welding electrode touch
any cylinder. Always secure cylinder to running gear, wall,
or other stationary support.
Beware of electric shock from wiring. Disconnect input
power before installing this kit. Reinstall all panels and
covers.
Falling equipment can cause injury and unit damage.
Never put any body part under unit while lifting. Lifting
forks must extend out opposite side of base. Lift unit
using proper equipment.
CALIFORNIA PROPOSITION 65 WARNINGS
Welding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in
some cases, cancer. (California Health & Safety Code Section 25249.5 et seq.)
This product contains chemicals, including lead, known to the state of California to cause cancer, birth defects, or other reproductive harm.
Wash hands after use.
2. Tools Needed
Optional
3/8 in.
OM-224 500 Page 2
3. Installing Running Gear
804 393-D
Remove paint from axle
grooves before installing
retaining rings (8).
6
7
8
1
2
3
4
5
6
7
8
9
10
11
12
4. Parts List
Item Part No. Description Qty.
1 224 502 Bracket, running gear top 1
2 168 663 Hook, spring .250, 2.375 lg, .312 snap opening 2
3 210 224 Chain 1
4 602 154 Screw, 250−20X, .50 hex washerhead, .50 diameter, steel plated, self−forming tap 10
5 228 547 Cylinder, rack 1
6 209 869 Wheel, polyolefin, 10 inch diameter x 2.000 wide x .750 2
7 602 250 Washer, flat, .812 ID x 1.469 OD x .134 thick, steel plated, ansi .750 2
8 121 614 Ring, retaining exterior, .750 shaft x .085 thick, e style plated 2
9 193 632 Nut, 375−16, .56 hex, .34 thick, steel plated serrated flange 2
10 223 293 Bracket, caster mounting 1
11 008 999 Caster, swivel, 4.00 inch polyolefin 2
12 235 506 Spacer 2
-
1
-
2
Miller RUNNING GEAR NO. 39 Owner's manual
- Category
- Car kits
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Miller MC050242L Owner's manual
-
-
-
-
Miller LH000000 Owner's manual
-
-
-
-
-