CyberData 011416 Owner's manual

Brand: CyberData

Model: 011416

Type: Owner's manual

Getting Started

Take the following into consideration before you install this product:

• Due to the size and mass of this product, it is important that the Backbox is safely installed according to these installation

instructions.

• Make sure that the type of wall is capable of supporting the system and use screws that are suitable for that type of wall.

• The system must be installed by qualified personnel in accordance with state and local building regulations.

• Also see the Install the DX80 Phone to Enclosure (on the other page).

• Locate the provided Security Torx Driver Bit (usually taped right next to the Hookswitch on the Faceplate).

• Tool required to remove Security Torx Screws (an Electric Hand Drill or Powered Screwdriver)

• WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation

instructions.

• WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.

• WARNING: This enclosure is not rated for any AC voltages!

Hookswitch Wires to USB to Analog Audio Module Connections

Contacting CyberData

Black Wire

USB - B Plug

on DX80

USB - A to B Cable

Plug in to Connector Panel

Plug in to (J1)

USB - A Plug

Red Wire

FACTORY DISCONNECTED

RECONNECT BEFORE FASTEN

FACEPLATE TO BACKBOX

***

ASSEMBLY

HOOKSWITCH

Red Wire to J4 (Position 5)

Black Wire to J4 (Position 9)

& WIRES TO SOCKET

SOCKET

PLUG

FACTORY PRE-INSTALLED

WIRES TO PLUG

Sales: (831) 373-2601 ext. 334

Support: 831-373-2601 ext. 333

Support Website: http://support.cyberdata.net/

RMA Department: (831) 373-2601 ext. 136

RMA Email: [email protected]

RMA Status: http://support.cyberdata.net/

Warranty Information: http://support.cyberdata.net/

Corporate Headquarters

CyberData Corporation

3 Justin Court

Monterey, CA 93940, USA

Phone: 831-373-2601

Fax: 831-373-4193

http://www.cyberdata.net/

Backbox Mounting Holes Dimensions

Armored Cord Handset to USB to Analog Audio Module

27.559 [700.00]

19.685 [500.00]

9.843 [250.00]

1.969 [50.00]

9.114 [231.50]

6.690 [169.92]

4.016 [102.00]

Approx.

5.118 [130.00]

2.047 [52.00]

2.421 [61.50]

12.567 [319.19]

22.953 [583.00]

9.114 [231.50]

2.047 [52.00]

5.118 [130.00]

16.929 [430.00]

Front

Bottom

Rear

Front

Left

Rear

Top

Front

Right

Front

Top

ø1.160 [ø29.50]

1.230 [31.25]

Hole Diameter

Typical EMT Fitting

Knock Out

ø0.63 [ø16.0]

ø0.41 [ø10.5]

Tool Required to Remove

1) Hammer

2) Screwdriver

Knock Out:

One Inch Conduit

EMT Fitting

Conduit Hole Fits

(One on Each Side)

ø1.30 [ø33.0]

Knock Out

View Shown with

Hole Plug Installed

Open Faceplate

then Remove Fastener

from the Inside

Tool Required to Remove

1) 3/8” Socket / Wrench

or 9mm Socket / Wrench

Nut Behind:

Notes:

1) Dimensions are in Inches [Millimeter]

2) Mounting Holes Fit Up to 1/4" Square Neck Carriage Bolt, 1/4" Self-Tapping or 10 Millimeter Machine Screw

3) 1" EMT Fitting is not provided.

Red Wire to J4 (Position 1)

Green Wire to J4 (Position 3)

Black Wire to J4 (Position 4)

Yellow Wire to J4 (Position 2)

1) #00 size Phillips Screw Driver

Tool Provided for Terminal Block Screw:

Armored Cord Wires End

The IP Endpoint Company

Installation Quick Reference

DX80 Secure Phone

011416

Install the DX80 Phone to Enclosure

2) Screwdriver or Nose Plier

1) Hammer

Tool Required to Remove Knockouts (KO):

1/4" Self-Tapping Screw

Up to 1/4" Square Neck Carriage Bolt

Knockouts (KO) & Keyhole Fit:

or 10 Millimeter Machine Screw

Place Phone

Power Supply

inside Holder

Connections

Label

ASSEMBLY

BACKBOX

Plug Power Plug

in to Power Jack

on the Connector Panel

Connector Panel

IEC Power Cord

The Other End

Through Desire

Conduit Hole Exit

to Power Source

Use Provided Security Torx

Driver Bit to Fasten Screws

Use Clean Damp Cloth to Wipe Surface Clean

Screen Cleaning Instruction:

Plexiglass Cleaning Instruction:

Plexiglass Cleaner to Wipe Surface Clean

ASSEMBLY

FACEPLATE

to Backbox

Tool Required:

Electric Hand Drill or

Powered Screwdriver

USB to Analog Audio Module Diagram

See Hookswitch to

for Details Connections

Open Wrench or Box Socket

Use 11/32" or 9mm

To Remove Nut

Connector Cover

Camera

Holder

Foot Stand

CLAMP

Strain Relief Bar

Plate

Microphone

Stand

Camera

Front

Behind

Turn to Open Lens Cover

on DX80 Phone

Use a Paper Clip Through Hole

to Access Power Button

Protective Film

from Both Sides

Before Close the Faceplate

6" Wire Tie (2x)

Wire Tie Mounting

1.5" Square

Base (2x)

Use provided cable management kit

to bundle up cables

#00 size Phillips Screw Driver

Jumper Shunt

Accessory Kits in Ziploc Type Bag

Phone Mounting Instruction:

Sightly Push Downward to Engage Locking

5) Place Strain Relief Bar on Top of CLAMPs

1) Lift Connector Cover Up

3) Place Foot Stand Behind Plate,

Microphones on to Stands.

2) Plug in All Neccessary Cables,

Cables Must be Placed Behind Strain Relief Bar

To Remove Phone from Box:

1) Lift Phone Up in Slow Motion then Remove

All Cables from Connector Panel.

JP2

Shunt

Install a Shunt on JP2 to

Enable Auto Answer Mode

CyberData 011416 Owner's manual

CyberData 011416 Owner's manual

CyberData 011416 Owner's manual

Related papers

Other documents