Genexis P2414 Installation guide

Genexis
Brand
Genexis
Model
P2414
Type
Installation guide

Genexis P2414 gives you a stable and secure internet connection via fiber optics, offering high-speed data transfer for seamless online experiences. Connect your phone and other devices to the LAN ports for a reliable wired connection. The LED indicators provide visual cues for system status, uplink connection, and phone service. It's easy to install, simply twist the device onto the Fiber Termination Unit (FTU), connect the power adapter, and you're good to go.

Genexis P2414 gives you a stable and secure internet connection via fiber optics, offering high-speed data transfer for seamless online experiences. Connect your phone and other devices to the LAN ports for a reliable wired connection. The LED indicators provide visual cues for system status, uplink connection, and phone service. It's easy to install, simply twist the device onto the Fiber Termination Unit (FTU), connect the power adapter, and you're good to go.

P
FiberTwist–Series
Installation Guide
Buton oveview Pot oveview
Power pot
Telephone
pot LAN pots
Unlock buton
Remove FiberTwist or Blind Cover – press and
hold while wisting counterclockwise
Reset buton (recessed)
Reset – press and release
LED dim buton
Dim LEDs – press and release to dim LEDs in
steps
System
Green – system ok
Green (blinking) – booting
Red – system error
Red (blinking) – insuicient optical signal
O – power o
Uplink
Green – link ok
Green (blinking) – link ok, no remote management
O – no link
Phone
Green – voice sevice registered and ok
Green (blinking) – voice sevice unregistered
O – voice sevice disabled
LED oveview
Box contents
• Genexis FiberTwist (active device)
• Power adapter
• Label (self-adhesive)
• Installation Guide (this document)
Label position
The product label is positioned on the
back of the active device.
Preparation
Ensure there is a power socket
within reach of where the device
is being installed.
Impotant: Instructions need
to be followed precisely and
uninterrupted. This minimizes
the risk of damage to the iber
optic connectors, causing a severe
degradation of signal qualiy.
Dierent language versions of this document and additional product information
are availableon htps:genexis.euproductibewistdownloads
Installation guide
Remove Blind Cover (if present)
. Press and hold the unlock buton (see buton oveview).
. Rotate the Blind Cover counterclockwise till it blocks.
. Remove the Blind Cover from the baseplate (FTU) by pulling
it towards yourself.
. Store the Blind Cover in a safe place.
Remove dust cap
. Take the FiberTwist out of the box.
. The dust cap is connected to the red string
located on the rear of the FiberTwist.
. Remove the dust cap by pulling the red string.
. Store the dust cap in a safe place.
Twist!
. Place the FiberTwist on the FTU as shown in the picture below,
in a –degree angle.
. Rotate clockwise until it clicks into place.
. Make sure the FiberTwist is aligned squarely on the FTU,
each edge must line up directly with the FTU below.
Your FiberTwist is now installed!
Company Name
Genexis B.V.
Company Address
Lodewijkstraat a
 AC Eindhoven
The Netherlands
Name and title of authorized person
Maaten Egmond, CTO
Signature of authorized person
Place of issue Date of issue
Eindhoven --
The Netherlands
Hereby, Genexis B.V. declares that the product FiberTwist-P is in compliance
with Directives EU, EU, EU, Delegated Directive
 and Ecodesign Directive EC.
The full text of the EU declaration of conformiy is available at the following
internet address: htps:genexis.euredt-P
EU Declaration of Conformiy
Connecting the FiberTwist
. If required, connect your telephone to the phone pot via an RJ nework cable.
. If required, connect your personal devices to the LAN pots via an RJ
nework cable.
. Connect the supplied power adapter to the FiberTwist and plug the adapter
into a power socket.
Warning: The FiberTwist is a Class  laser product.
If at some point in the future it becomes necessay to uninstall the FiberTwist,
please place the Blind Cover back on the FTU immediately and put the dust cap
back on the FiberTwist.
Revision . - June - Copyright ©  Genexis Netherlands B.V. All rights reseved.
Genexis assumes no responsibiliy for any inaccuracies in this document. Genexis reseves
the right to change, modify, transfer, or othewise revise this publication without notice.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Genexis P2414 Installation guide

Genexis
Brand
Genexis
Model
P2414
Type
Installation guide

Genexis P2414 gives you a stable and secure internet connection via fiber optics, offering high-speed data transfer for seamless online experiences. Connect your phone and other devices to the LAN ports for a reliable wired connection. The LED indicators provide visual cues for system status, uplink connection, and phone service. It's easy to install, simply twist the device onto the Fiber Termination Unit (FTU), connect the power adapter, and you're good to go.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents