Spektrum SR6300PM User manual

Brand: Spektrum

Model: SR6300PM

Category: Remote controlled toys

Type: User manual

Spektrum SR6300PM receiver, compatible with all Spektrum DSMR surface transmitters, provides advanced telemetry and MS6X technology for precise control and real-time data monitoring. Enable/disable MS6X during binding, ensuring optimal performance for various applications. Enjoy telemetry functions, including SMART Throttle, for voltage and temperature monitoring.

MS6X Telemetry Receiver Instruction Manual

MS6X-Telemetrieempfänger-Bedienungsanleitung

Manuel d’instructions du récepteur MS6X avec télémétrie

Manuale di istruzioni del ricevitore MS6X con telemetria

SR6300PM

The following terms are used throughout the product literature to indicate

various levels of potential harm when operating this product:

WARNING: Procedures, which if not properly followed, create the probability

of property damage, collateral damage, and serious injury OR create a high

of physical property damage AND a little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability

of physical property damage AND a possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of

physical property damage AND a little or no possibility of injury.

NOTICE

All instructions, warranties and other collateral documents are subject to

change at the sole discretion of Horizon Hobby, LLC. For up-to-date product

literature, visit horizonhobby.com or towerhobbies.com and click on the

support or resources tab for this product.

Meaning of Special Language

Age Recommendation: Not for children under 14 years. This is not a toy.

WARNING: Read the ENTIRE instruction manual to become familiar

with the features of the product before operating. Failure to operate

the product correctly can result in damage to the product, personal property

and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution

and common sense and requires some basic mechanical ability. Failure to

operate this Product in a safe and responsible manner could result in injury

or damage to the product or other property. This product is not intended for

use by children without direct adult supervision. Do not attempt disassembly,

use with Incompatible components or augment product in any way without

the approval of Horizon Hobby, LLC. This manual contains instructions for

safety, operation and maintenance. It is essential to read and follow all the

instructions and warnings in the manual, prior to assembly, setup or use, in

order to operate correctly and avoid damage or serious injury.

WARNING AGAINST COUNTERFEIT PRODUCTS: Always

purchase from a Horizon Hobby, LLC authorized dealer to ensure

authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all

support and warranty with regards, but not limited to, compatibility and

performance of counterfeit products or products claiming compatibility with

DSM or Spektrum technology.

NOTICE: This product is only intended for use with unmanned, hobby-grade,

remote-controlled vehicles. Horizon Hobby disclaims all liability outside of

the intended purpose and will not provide warranty service related thereto.

WARRANTY REGISTRATION

Visit www.community.spektrumrc.com today to register your product.

TABLE OF CONTENTS

SR6300PM RECEIVER DIAGRAM .................................................................. 4

MS6X RECEIVER INSTALLATION ................................................................... 5

BINDING AND CALIBRATING ......................................................................... 6

FAILSAFE .................................................................................................... 7

DISABLING MS6X TECHNOLOGY .................................................................. 7

MS6X TECHNOLOGY SETUP ........................................................................ 8

MS6X TUNING............................................................................................. 9

2.4GHZ TROUBLESHOOTING GUIDE ........................................................... 12

TELEMETRY TROUBLESHOOTING GUIDE ..................................................... 13

MS6X TROUBLESHOOTING GUIDE .............................................................. 13

1-YEAR LIMITED WARRANTY ..................................................................... 14

WARRANTY SERVICE AND CONTACT INFORMATION .................................... 16

FCC INFORMATION ................................................................................... 16

SUPPLIER’S DECLARATION OF CONFORMITY ............................................. 16

IC INFORMATION ....................................................................................... 17

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION ........................... 17

Specications SR6300PM

Type DSMR MS6X Receiver with Telemetry

Dimensions (L × W × H) 38.9mm x 24.1mm x 13.8mm

Antenna Length 9 in (2.5 cm)

Channels 6

Weight 9.3g

Band 2405 MHz – 2478 MHz

Voltage Range 3.5–9.6V

NOTICE: Digital servos are required with the SR6300PM MS6X receiver.

Using analog servos with MS6X technology will reduce the performance of

the system and may cause the servos to overheat.

The Spektrum™ SR6300PM MS6X Telemetry Receiver is compatible with all

Spektrum DSMR® surface transmitters. Telemetry functions require a Spektrum

DSMR transmitter capable of telemetry, and SMART Throttle telemetry may

require a ﬁrmware update for your transmitter. Visit the product page for your

transmitter at SpektrumRC.com for more information.

TELEMETRY WITH SMART THROTTLE

With SMART Throttle the normal throttle lead delivers the throttle signal to

the ESC, plus the ESC can send telemetry data like voltage and temp back to

the receiver. For SMART Throttle to function you must use a SMART Throttle

ESC paired with a SMART Throttle telemetry receiver, and a Spektrum DSMR

transmitter with telemetry. Only certain Spektrum products include SMART

technology, check your ESC and transmitter manual for more information.

SMART THROTTLE

The SR6300PM receiver throttle port includes SMART Throttle. The SR6300PM

receiver throttle port will automatically detect when a SMART Throttle compatible ESC

is plugged in and the throttle port will begin to operate in SMART Throttle mode.

ESCs with SMART Throttle and IC series connectors can also pass along battery

data from compatible Spektrum SMART batteries.

The SR6300PM is compatible with the Spektrum Firma™ line of ESCs for SMART

Throttle.

NORMAL SERVO SIGNAL (PWM)

If a standard ESC or servo is plugged into the throttle port on the SR6300PM

receiver, the throttle port will operate normally like any conventional RC system

(PWM signal).

AUX 2 Port

AUX 3 Port

AUX 4 Port Antenna

Bind Button

POWERING THE RECEIVER WITH AN ESC

1. Connect the steering servo to the steering port (STR)

2. Connect the throttle servo to the throttle port (THR). Most ESCs will have an

integrated BEC (battery eliminator circuit) which will power the ESC from the

motor battery, through the throttle lead. Connecting the ESC to any of the

ports on the servo rail will power the receiver when the ESC is turned on.

POWERING THE RECEIVER WITH A SEPARATE RECEIVER PACK

1. Connect the steering servo to the steering port (STR)

2. Connect the throttle servo to the throttle port (THR)

3. Connect the switch harness and a 3.5V–9.6V battery to the battery (BATT)

port to power on receiver.

SR6300PM RECEIVER DIAGRAM

AUX 1 Port

Battery/

Programming

Throttle Port

Steering Port

MS6X RECEIVER INSTALLATION

Install the SR6300PM receiver in the vehicle as shown before binding the

transmitter and receiver. When binding the receiver, the MS6X system

automatically detects the orientation of the receiver.

The receiver has a designated location with a very speciﬁc orientation that

it must be mounted.

If the receiver is mounted in any other location or angle,

MS6X technology may not function properly.

You may mount the receiver on any of its six sides, and it does not matter

which direction the receiver is pointed. The receiver doesn’t even need to be

square with the vehicle, as long as it is ﬂat and level.

IMPORTANT: Do not use hook and loop tape to install the SR6300PM receiver.

Using hook and loop tape will effect the performance of the MS6X system.

ANTENNA INSTALLATION

The SR6300PM receiver has a coaxial style antenna. Position the antenna

vertically and away from the vehicle in an antenna tube. Make sure the tip of

the antenna is as high as possible to maximize the signal strength.

NOTICE: Do not cut, kink, or modify the antenna. Damage to the coaxial

portion of the antenna will reduce the performance of the antenna.

Shortening or cutting off the 31mm tip will reduce the range to a small

fraction of what it should be.

NOTICE: Do not connect a dedicated receiver battery to the receiver along

with an ESC (with a BEC, a feature which most ESCs include). When an ESC

is powered on it provides the receiver with regulated power from the main

battery through the throttle connection. The ESC, battery and/or receiver may

be damaged if the receiver is also connected to a dedicated receiver battery.

This does not apply to an ESC without a BEC.

Active portion

of antenna

FPO need Illustration of spot installed

in the bike.

BINDING AND CALIBRATION PROCESS

Upon initial setup after the ﬁrst bind, the model must be conﬁgured for servo

direction, trim and travel. Then the receiver must be rebound and calibrated to

those settings for proper operation. Center the steering trim and throttle trim on

the transmitter before beginning.

1. Press and hold the bind button on the receiver.

2. Power on the receiver. The orange LED ﬂashes, indicating the receiver is in

bind mode. Release the bind button after the orange LED illuminates.

3. Put your transmitter in bind mode.

4. The bind process is complete when the orange LED on the receiver

remains lit. At this stage the receiver is connected but must complete

calibration before it will operate.

5. Pull the transmitter trigger to full throttle, pause, then return the trigger to

center.

6. Push the transmitter trigger to full brake, pause, then return the trigger to

center.

7. Turn the transmitter steering wheel to full right, pause, then return the

wheel to center.

8. Turn the transmitter steering wheel to full left, pause, then return the

steering wheel to center. The orange LED ﬂashes to conﬁrm the settings

have been accepted.

9. Turn off the vehicle to complete the binding and calibration process.

CAUTION: When the bind process is complete, the throttle and

steering channels are active. Keep hands and loose objects away

from all spinning parts on the vehicle.

Bind Button

BINDING AND CALIBRATING

Binding is the process of linking the SR6300PM receiver to your Spektrum

transmitter. The MS6X features on the receiver can be enabled or disabled

during the binding process. There is no bind plug on the SR6300PM, a button

is used to put the receiver in bind mode.

IMPORTANT: You must calibrate the SR6300PM receiver each time it is placed

in bind mode, regardless of MS6X being enabled or disabled.

FAILSAFE

In the unlikely event that the radio link is lost during use, the receiver will drive

the throttle channel to the neutral position. If the receiver is powered on prior

to turning on the transmitter, the receiver will enter the failsafe mode, driving

the throttle channel to the neutral position. When the transmitter is turned on,

normal control is resumed.

IMPORTANT: Failsafe activates only in the event that signal is lost from the

transmitter. Failsafe will NOT activate in the event that receiver battery power

decreases below the recommended minimums or power to the receiver is lost.

IMPORTANT: You must rebind the transmitter and receiver if you:

• change the servo reversing after binding

• change the travel after binding

• change the receiver mounting orientation

• use the receiver with a different model memory

• install the receiver in a different vehicle

• use the receiver in 5.5ms and want telemetry, rebind in 11ms

• use the receiver with a DSMR transmitter and you change the frame rate

in the transmitter

DISABLING MS6X TECHNOLOGY

MS6X may be disabled during binding.

1. Connect power to the receiver and quickly press and release the bind

button three times (within 1.5 seconds).

2. Connect power to the receiver, power on, press and release the bind

button three times (within 1.5 seconds from the ﬁrst push).

When the MS6X system has been disabled, the LED on the receiver will show

three ﬂashes upon power up, and then remain lit. The receiver is bound and

operating normally when the LED remains illuminated.

TIP: If the MS6X feature in the receiver is active and the MS6X menu in the

transmitter is Inhibited, MS6X functions will default to the AUX 1 and AUX 2

operation, and in this scenario, MS6X will not work correctly.

Selecting INH in the MS6X menu on your transmitter will not disable

MS6X.

SERVO TRAVEL WITH MS6X TECHNOLOGY

MS6X technology requires at least 80% travel on steering and throttle in all

directions to complete calibration. If you have reduced travel to below 80%,

you must increase the travel above 80% to complete calibration.

For vehicles with a mechanical brake, very little servo travel is used to apply

braking force. In this case it is common to reduce throttle travel for braking well

below 80%. To calibrate a vehicle with a mechanical brake, increase the brake

travel above 80% whenever the vehicle is calibrated (bound), then change the

braking travel back to the travel setting for your brakes.

AUX CHANNELS AND MS6X TECHNOLOGY

When MS6X is active, the SR6300PM receiver will use the AUX 1 and AUX 2

channels for gain control. AUX 1 and AUX 2 should be allocated for MS6X when

MS6X is active. This is done automatically when the MS6X menu is selected

in your transmitter, but if you are not using the MS6X menu, AUX1 or AUX2

should not be used for other mixes or to control other applications (servos, etc.)

The AUX 1 and AUX 2 ports can be used in MS6X mode to power a personal

transponder, lights, drive servos, or operate auxiliary devices. However, AUX 1

will command steering gain, and AUX 2 will command throttle gain regardless

of what is plugged into the AUX 1 or AUX 2 ports. AUX 1 and AUX 2 are not

independent when MS6X is active. For an independent channel, use AUX 3 or

TIP: Using the SR6300PM receiver without the MS6X menu on your

transmitter or using AUX 1 or AUX 2 to command auxiliary functions may result

in poor MS6X performance.

• If 5.5ms frame rate is selected in the transmitter, only two channels,

Steering and Throttle, are operational. The Aux channels can be used to

power a personal transponder or lights.

• If a frame rate other than 5.5ms is selected, the Aux channels will

operate as extra servo channels.

MS6X TECHNOLOGY SETUP

For the best MS6X performance, use the MS6X menu on your Spektrum

transmitter to tune and manage MS6X settings.

Order of operations for MS6X setup:

1. Install the receiver in your vehicle

2. Bind the vehicle and complete the calibration procedure.

3. Set up servo sub trim, reversing and travel to suit your vehicle.

4. Re-bind and complete calibration again so calibration matches the model

setup.

5. Drive the vehicle with no gain on MS6X settings to verify your travel and

other basic settings. If any changes are made re-bind and re-calibrate.

6. Follow the MS6X tuning procedure in this manual.

MS6X TUNING

A value from 0 to 100 is used for three settings that affect tuning; steering

gain, throttle gain, and priority. These values conﬁgure the receiver to your

vehicle so you can tune it for optimal performance based on your driving style.

It is normal for gain and priority tuning results to vary.

WHAT IS GAIN?

A gain value of 0 will result in zero electronic corrections, and a gain of 100

will result in large corrections in an effort to hold a straight line.

• Steering gain tells the receiver how strongly to assist steering when the

vehicle begins to spin out of control.

• Throttle gain manages how much the receiver can ease off the throttle

when the vehicle begins to spin out of control.

The default gain values in Spektrum transmitter MS6X menus are set at 50.

We recommend adjusting gain values 5 points at a time. Fine tune the settings

with smaller increments as desired performance is achieved.

WHAT IS PRIORITY?

Priority tells the receiver how much you want to be able to override the

electronic stability with your steering commands. A low priority means MS6X

will make steering corrections when you turn the wheel all the way. A high

priority will reduce MS6X the more you turn the wheel.

The default priority value in Spektrum transmitter MS6X menus is 100. This

means when you turn the steering wheel to the limit, the gain is reduced to

zero. This value will work well for a majority of drivers.

WHAT IS HEADING HOLD?

Heading hold maintains the vehicle’s direction. It is normal to see the wheels

steer in the same direction the vehicle was last pointed. If a vehicle with MS6X

technology is lifted off the ground and turned from side to side, the wheels will

steer in an effort to get back to the original heading. When driving, heading

hold only works when the steering wheel is left straight. The moment you

begin to turn the wheel, heading hold turns off. When the wheel is re-centered,

heading hold is turned back on and is set to the new heading.

MS6X TUNING PROCEDURE

1. With the transmitter and receiver already bound and properly calibrated,

turn on the transmitter and vehicle.

2. Apply throttle, do not turn the steering wheel, and observe how well the

vehicle can maintain a straight line at high speed.

• If the vehicle does not make enough steering corrections to maintain a

straight line, increase the steering gain.

If the vehicle ﬁshtails due to wheel-spin, increase the throttle gain.

• If the vehicle wobbles (oscillates), reduce the steering gain.

• Once you ﬁnd the highest steering gain values that don’t cause

oscillations at high speed, use those numbers as your steering gain

limit and don’t go any higher.

3. Drive the vehicle through accelerated turns and observe how it responds.

• If the vehicle slows down going into a turn, reduce the throttle gain.

• To allow the vehicle to slide more with intentional wheel-spin, reduce

the throttle gain.

• To improve traction in slick conditions, increase throttle gain.

• If the vehicle won’t turn-in, increase the priority.

• If the vehicle spins out, there are two tuning options to consider;

1. Increasing throttle gain will give the receiver more authority to

reduce throttle when the vehicle begins to spin out.

2. Reducing priority will give the receiver more authority to help

correct oversteer.

GENERAL MS6X TUNING TIPS

For beginner drivers, low grip conditions, and vehicles with excessive power,

more gain will be helpful.

For terrain with more grip and increased speeds, tuning will result in lower

steering gain values.

CHANGING BATTERY VOLTAGE WHEN USING MS6X

If you increase voltage going to your vehicle, the maximum steering gain

setting will have to be reduced.

At the same time, when increasing voltage increased throttle gain will help

manage the extra power.

For example: If a Motorcycle set up for 2S is upgraded to 3S, the Motorcycle

may oscillate at high speeds on 3S, requiring steering gain reduction. Throttle

gain will have a bigger effect on 3S, so increasing throttle gain may be

beneﬁcial.

RECEIVER FIRMWARE UPDATES

If ﬁrmware updates are made available for the SR6300PM receiver, you can

install the update yourself. The Spektrum USB programming cable (SPMA3065,

not included) and a PC are required for updates. Go to the SR6300PM product

page at SpektrumRC.com for update information and to register your receiver.

Registration is required to download updates.

To Update:

1. Register your receiver and download the Spektrum programmer and the

ﬁrmware update for the SR6300PM (when available).

2. Install the Spektrum programmer on your PC and open the app. Connect

the USB programming cable to your PC and allow it to install the drivers.

NOTICE: In the programmer app there is an option to power the receiver

from the PC. Leave this box checked. DO NOT connect a power source

to the receiver at the same time as the USB cable.

If the box in the programmer app is checked to power the receiver from

the computer, and the USB cable is plugged into the receiver, and a power

source is plugged into the receiver, there is a high probability of causing

permanent damage to the PC.

3. With the vehicle and receiver powered off, plug the updater cable into

the programming port on the SR6300PM. DO NOT turn on the vehicle or

receiver when the USB cable is connected. The PC should connect with

the receiver automatically.

4. Follow the on screen prompts in the to install the ﬁrmware ﬁle on the

SR6300PM.

5. When the update is complete, unplug the updater cable from the receiver.

Verify this check-box is checked to power the receiver from the PC during

the update.

Problem Possible Cause Solution

The system

will not

connect

Your transmitter and

receiver are too close

together

Move transmitter 8–12 feet away

from receiver

You are near metal objects Move to an area with less metal

The receiver is bound to a

different model memory

Make sure the correct model memory

is active in your transmitter

Your transmitter was placed

into bind mode and is

no longer bound to your

receiver

Rebind your transmitter and receiver,

and then re-calibrate

The receiver

goes into

failsafe

a short

distance

away

from the

transmitter

Check for damage on the

receiver antenna

Make sure your receiver antenna

is protected and located as high as

practical

Replace the receiver or contact

Horizon Product Support

The receiver

stops

responding

during

operation

Low receiver battery

voltage. If the battery

voltage is low, it may drop

below 3.5V momentarily,

causing the receiver to

brown-out, then reconnect

Charge the receiver or vehicle battery.

Spektrum receivers require at least

3.5V to operate

Loose or damaged wires or

connectors between battery

and receiver

Check the wires and connection

between the battery and receiver.

Repair or replace wires and/or

connectors

2.4GHZ TROUBLESHOOTING GUIDE

Problem Possible Cause Solution

No telemetry

options are

available in the

transmitter

You are using a transmitter

that does not include

telemetry features

Consider changing to a

transmitter which includes

telemetry

Your transmitter is in 5.5ms

mode

Select a different DSMR

protocol, rebind and then

recalibrate

The telemetry

screen is blank

The telemetry screen needs

to be conﬁgured in the

transmitter telemetry menu

Conﬁgure the telemetry screen

SMART battery

information is not

coming through

telemetry

Not using a SMART

compatible ESC or receiver

An SMART ESC and receiver

are required for SMART

Battery data to be sent through

telemetry

SMART Throttle

ESC data is not

coming through

telemetry

Throttle lead from the ESC

is not plugged into the

correct port on the receiver.

Connect the ESC to the

Throttle (THR) port on the

receiver. No other ports

support SMART Technology.

Problem Possible Cause Solution

Vehicle Oscillates

(wobbles or shakes) at

high speeds

Steering gain is too high Reduce steering gain

Vehicle responds

strangely to controls

Receiver not properly

calibrated Conﬁrm servo direction

and travel are correct,

then re-bind and re-

calibrate the receiver

Vehicle setup changed

after calibration

Receiver not mounted level

Conﬁrm the receiver is

truly ﬂat, it cannot be

mounted at an odd angle.

Receiver won’t ﬁnish the

calibration

Travel adjust is below 80%

on steering or throttle

Increase travel adjust and

re-calibrate. See page

19 for more information

about setting up vehicles

with a mechanical brake.

Driver expects MS6X

should be turned off, but

it is still turned on

MS6X menu is inhibited,

but AUX values are at

neutral, which works out

to 50% gain but with no

priority.

Disable MS6X during

binding, or change MS6X

menu to on and set all

gain values to 0

MS6X TROUBLESHOOTING GUIDE

TELEMETRY TROUBLESHOOTING GUIDE

1-Year Limited Warranty

What this Warranty Covers—Horizon Hobby, LLC, (Horizon) warrants to the original

purchaser that the product purchased (the "Product") will be free from defects in

materials and workmanship for one year from the date of purchase.

What is Not Covered—This warranty is not transferable and does not cover (i) cos-

metic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence,

commercial use, or due to improper use, installation, operation or maintenance, (iii)

modiﬁcation of or to any part of the Product, (iv) attempted service by anyone other

than a Horizon Hobby authorized service center, (v) Product not purchased from an

authorized Horizon dealer, (vi) Product not compliant with applicable technical regula-

tions, or (vii) use that violates any applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER

WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED

WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES

OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETER-

MINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE

PURCHASER’S INTENDED USE.

Purchaser’s Remedy—Horizon’s sole obligation and purchaser’s sole and exclusive

remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any

Product determined by Horizon to be defective. Horizon reserves the right to inspect

any and all Product(s) involved in a warranty claim. Service or replacement decisions

are at the sole discretion of Horizon. Proof of purchase is required for all warranty

claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE

PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability—HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT,

INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION

OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS

BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY

OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSI-

BILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the

individual price of the Product on which liability is asserted. As Horizon has no control

over use, setup, ﬁnal assembly, modiﬁcation or misuse, no liability shall be assumed

nor accepted for any resulting damage or injury. By the act of use, setup or assembly,

the user accepts all resulting liability. If you as the purchaser or user are not prepared

to accept the liability associated with the use of the Product, purchaser is advised to

return the Product immediately in new and unused condition to the place of purchase.

Law—These terms are governed by Illinois law (without regard to conﬂict of law

principals). This warranty gives you speciﬁc legal rights, and you may also have other

rights which vary from state to state. Horizon reserves the right to change or modify

this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services—Your local hobby store and/or place of

purchase cannot provide warranty support or service. Once assembly, setup or use

of the Product has been started, you must contact your local distributor or Horizon

directly. This will enable Horizon to better answer your questions and service you in the

event that you may need any assistance. For questions or assistance, please visit our

website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll

free telephone number referenced in the Warranty and Service Contact Information

section to speak with a Product Support representative.

Inspection or Services—If this Product needs to be inspected or serviced and is

compliant in the country you live and use the Product in, please use the Horizon Online

Service Request submission process found on our website or call Horizon to obtain a

Return Merchandise Authorization (RMA) number. Pack the Product securely using a

shipping carton. Please note that original boxes may be included, but are not designed

to withstand the rigors of shipping without additional protection. Ship via a carrier that

provides tracking and insurance for lost or damaged parcels, as Horizon is not respon-

sible for merchandise until it arrives and is accepted at our facility. An Online Service

Request is available at http://www.horizonhobby.com/content/service-center_render-

service-center. If you do not have internet access, please contact Horizon Product

Support to obtain a RMA number along with instructions for submitting your product

for service. When calling Horizon, you will be asked to provide your complete name,

street address, email address and phone number where you can be reached during

business hours. When sending product into Horizon, please include your RMA number,

a list of the included items, and a brief summary of the problem. A copy of your

original sales receipt must be included for warranty consideration. Be sure your name,

address, and RMA number are clearly written on the outside of the shipping carton.

NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo

battery, please contact the appropriate Horizon Product Support ofﬁce.

Warranty Requirements—For Warranty consideration, you must include your

original sales receipt verifying the proof-of-purchase date. Provided warranty condi-

tions have been met, your Product will be serviced or replaced free of charge. Service

or replacement decisions are at the sole discretion of Horizon.

Non-Warranty Service—Should your service not be covered by warranty, service

will be completed and payment will be required without notiﬁcation or estimate of the

expense unless the expense exceeds 50% of the retail purchase cost. By submitting

the item for service you are agreeing to payment of the service without notiﬁcation.

Service estimates are available upon request. You must include this request with your

item submitted for service. Non-warranty service estimates will be billed a minimum

of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts

money orders and cashier’s checks, as well as Visa, MasterCard, American Express,

and Discover cards. By submitting any item to Horizon for service, you are agreeing to

Horizon’s Terms and Conditions found on our website http://www.horizonhobby.com/

content/service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country of use

and ownership. If received, a non-compliant Product will not be serviced. Further,

the sender will be responsible for arranging return shipment of the un-serviced

Product, through a carrier of the sender’s choice and at the sender’s expense.

Horizon will hold non-compliant Product for a period of 60 days from notiﬁcation,

after which it will be discarded.

10/15

Country of

Purchase Horizon Hobby Contact

Information Address

United States

of America

Horizon Service Center

(Repairs and Repair

Requests)

servicecenter.

horizonhobby.com/

RequestForm/ 2904 Research Rd.

Champaign, Illinois

61822

USA

Horizon Product Support

(Product Technical

Assistance)

productsupport@

horizonhobby.com

877-504-0233

Sales

websales@

horizonhobby.com

800-338-4639

Horizon Technischer

Service

service@

horizonhobby.eu

Hanskampring 9

D 22885

Barsbüttel,

Germany

Sales: Horizon Hobby

GmbH

+49 (0) 4121

2655 100

WARRANTY SERVICE AND CONTACT INFORMATION

FCC ID: BRWSPMSR6300PM

Supplier’s Declaration of Conformity

SPMSR6300PM 6 Channel DSMR MS6X Telemetry Receiver

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including interference

that may cause undesired operation.

This equipment complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

minimum distance 20 cm between the radiator & your body ( excluding ﬁngers,

hands, wrists, ankles and feet). This transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter.

CAUTION: Changes or modiﬁcations not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Horizon Hobby, LLC

2904 Research Road Champaign, IL 61822

Email: compliance@horizonhobby.com

Web: HorizonHobby.com

FCC INFORMATION

IC INFORMATION

CAN ICES-3 (B)/NMB-3(B)

IC: 6157A-SPMSR6300PM

This device contains license-exempt transmitter(s)/receivers(s) that comply with

Innovation, Science, and Economic Development Canada’s license-exempt RSS(s).

Operation is subject to the following 2 conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux

appareils radio exempts de licence. L’exploitation est autoriséeaux deux conditions

suivantes :

1. l’appareil ne doit pas produire de brouillage.

2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

meme si le brouillage est susceptible d’en compromettre lefonctionnement.

This equipment complies with IC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated

with minimum distance 20 cm between the radiator & your body.

Déclaration d’exposition aux radiations:

Cet équipement est conforme aux limites d’exposition aux rayonnements

IC établies pour un environnement non contrôlé. Cet équipement doitêtre

installé et utilisé avec un minimum de 20 cm de distance entre la source de

rayonnement et votre corps.

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION

EU Compliance Statement:

Hereby, Horizon Hobby, LLC declares that the

device is in compliance with the following:

EU Radio Equipment Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet

address: https://www.horizonhobby.com/content/support-render-compliance.

Wireless Frequency Range and Wireless Output Power:

2405 – 2478 MHz

6dBm

Manufacturer:

Horizon Hobby, LLC

2904 Research Road

Champaign, IL 61822 USA

Importer:

Horizon Hobby, GmbH

Hanskampring 9

22885 Barsbüttel Germany

WEEE NOTICE:

This appliance is labeled in accordance with European Directive

2012/19/EU concerning waste of electrical and electronic equipment

(WEEE). This label indicates that this product should not be disposed

of with household waste. It should be deposited at an appropriate

facility to enable recovery and recycling.

MS6X, Active Vehicle Control, the SMART technology logo, Firma, DSM, DSM2,

DSMR, Hangar 9, QuickConnect, ModelMatch, SmartSafe and the Horizon

Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.

The Spektrum trademark is used with permission of Bachmann Industries, Inc.

US 9,320,977. US 10,528,060. US 9,930,567. US 10,419,970.

Other patents pending.

318044 Created 07/22 SPMSR6300PM

Spektrum SR6300PM User manual

Brand: Spektrum

Model: SR6300PM

Category: Remote controlled toys

Type: User manual

Download PDF

report

Spektrum SR6300PM User manual

Spektrum SR6300PM User manual

Related papers

Other documents