GreenTech Pro and Room Owner's manual

Owner’s Manual

Pro and Room Models

Important Safety Information

Table of Contents

Do not operate this unit unless it is completely assembled.

Do not block the ventilation filter.

Do not directly view UV lights while in operation.

Unplug unit before any cleaning or maintenance.

This unit is not intended for outdoor use.

NOTE: Read this manual and all important safety instructions before using the unit.

Important Safety Information ....2

Product Contents ................3

Initial Setup ......................3

Diagrams ......................4-5

Controls .........................6

Greentech Connect .............. 7

Operation ......................8-9

Cleaning & Maintenance ........10

Part Replacement ............ 11-13

Specifications ...................14

Warranty Information ............15

Initial Setup

Product Contents

· pureAir Active HEPA+ Unit

· Unit Storage Bag

· Power Cord

· Owner’s Manual

· Quickstart Guide

· Remove your unit from the packaging. (Keep your bag and included materials)

· Open the unit and take the filter out of the protective wrap and place the

filter back into the unit before operation.

· Install the Power Cord into the plug on the bottom of the unit, under the

sliding panel.

· Locate a suitable location to place your unit. (Ideal location is an area of the

room with good circulation, away from the wall and your air return, or near

the source of pollution)

· Connect your unit to WiFi via Greentech Connect Mobile Application.

(See Greentech Connect, Page 7)

· Begin purification!

Diagrams

Air Intake

(Pre-Filter)

Power Cord

Power Cord Inlet/Cover

Power Cord Management Area

Control Panel

Air Vent

NOTE: All diagrams shown are of the Active HEPA+ Room, but also apply to the Active HEPA+ Pro.

Handle/BPI Module Access

Unit Housing Button

(Press to remove unit top)

Air Quality Sensor

Diagrams

HEPA Filter

Control Panel

PCO Cell

BPI Module

(Brush Plugs)

Fan Motor

Housing

Controls

GOOD

Component

Status

Display

Active Display

Information

Unit Power

Fan Speed

Manual Mode

Auto Mode Sleep Mode

Information

Environment &

Components

WiFi Status

Indicator

Greentech Connect

pureAir Active HEPA+ can be controlled with the unit’s control panel as well as

with the mobile application, Greentech Connect.

• Scan this QR Code to download from your app store.

• Create your account.

• Set your unit in WiFi discovery mode by

holding the Power Button down until the WiFi

symbol begins to blink.

• In Greentech Connect, press the + button in

the top right corner and add a new device.

Your device should automatically show up

while in discovery mode.

• After your device has been added, select the

unit and enter its control screen.

• Make mode, fan, and lighting adjustments, or

view the quality of your air, part life, and more.

For more Greentech Connect information scan the

QR Code on your unit.

Operation

Unit Power

Press the Power Button to turn the unit ON or OFF.

Fan Speed (Manual Mode)

Press the Fan Speed Button (FAN) to cycle through the 5 fan speeds

(Low, Med-Low, Medium, Med-High, High).

Auto Mode

Press the Auto Mode Button (AUTO) to put the unit into Auto Mode. During

Auto Mode your unit will adjust fan speed based upon the air quality

while showing a notification of the current air quality level.

Air Quality - Displayed During Operation

· Good (Green) · Fair (Yellow) · Poor (Red)

NOTE: The Air Quality Sensor takes 15 minutes to fully calibrate after turning the unit on. If

you need to quickly take care of an air issue, we recommend starting the unit in Manual

Mode on your desired Fan Speed.

Operation

Night Mode - Dims all lights (Control Panel, Air Quality LED, PCO UV LEDS )

First, choose your preferred purification mode/fan speed. Press the Night

Mode button to turn Night Mode ON. Press any button to “wake” the unit

up before the set 8 hour Night Mode period ends.

Note: Night Mode time settings can be adjusted in the mobile app, Greentech Connect.

Information

Pressing the information button will cycle through real-time unit and

room information. The actively displayed information will be highlighted

in the Component Status or Active Display Information sections on

the control panel. This information is also available in the GreenTech

Connect Mobile App.

· Temperature - Current Room Temperature

· Humidity - Current Room Humidity

· Filter Life - % Remaining

· PCO Cell Life - % Remaining

· BPI Module Life - % Remaining

Cleaning & Maintenance

WARNING: UNPLUG UNIT BEFORE CLEANING OR MAINTENANCE

Cleaning

For proper operation, the unit should be cleaned once a month.

· Unit Exterior – Wipe down with damp cloth

· Pre Filter – Vacuum

· Unit Interior – Remove top of unit to remove filter, wipe interior of unit with damp cloth or vacuum and then

return filter and replace top of unit Replace the filter (Annually or Biannually)

· Air Quality Sensor – Spray with compressed air and/or wipe with alcohol swab

Maintenance

If your unit has stopped working properly, refer to your Warranty Information for

coverage and replacement instructions.

HEPA Filter Life

Filter life is determined by operating time, but is affected by the level of

pollutants in the space being cleaned. Filters should be replaced at least once

a year to ensure the highest quality purification, or more frequently in locations

with higher levels of pollutants.

PCO Cell and BPI Module Life

The PCO Cell and BPI Module life are determined by operating time and should

be replaced once a year to ensure the highest quality purification.

Temperature Unit Adjustment (ºF/ºC)

Easily switch between Fahrenheit and Celsius within the Greentech Connect

Mobile App by selecting the temperature section on the control screen.

Part Replacement - HEPA Filter with ODOGard® Coating

(1) Remove the top. (2) Remove filter. (3) Replace with new filter. (4) Replace top.

Additional Filters, PCO Cells, and BPI Modules can be purchased through

Greentech Environmental or a Greentech Environmental retailer.

(5) Reset the Filter Life by navigating the information menu to the Filter

Life screen and holding the information button until the life remaining

changes to 100%.

Note: To reset the Filter Life using Greentech Connect, navigate to the unit control screen,

select the Filter section and reset the life remaining.

Part Replacement - PCO Cell

(1) Remove the top. (2) Pull the PCO Cell straight up to remove it from the

internal post. (3) Replace with the new cell by aligning the keys on the cell and

post then slide it down until fully seated. (4) Replace the top.

(5) Reset the PCO Cell Life by navigating the information menu on the

control panel to the PCO Cell Life screen and holding the information

button until the life remaining changes to 100%.

Note: To reset the PCO Cell life using Greentech Connect, navigate to the unit control screen,

select the PCO Cell section and reset the life remaining.

(1) Remove the two screws located on the inner/top edge of the rear handle.

(2) Remove the handle cover. (3) Remove the two BPI Brush Plugs by grabbing

and lifting them up and out. (4) Replace with the new BPI Brush Plugs by

inserting them into their color-coordinated outlets until they are fully seated.

(5) Replace the handle cover and screws.

Part Replacement - BPI Module Brushes

(6) Reset the BPI Module Life by navigating the information menu to

the BPI Module screen and holding the information button until the life

remaining changes to 100%.

Note: To reset the BPI Module Life using Greentech Connect, navigate to the unit control

screen, select the PCO Cell section and reset the life remaining.

Specifications

Troubleshooting

* This warranty is conditional to yearly maintenance requirements outlined in the Warranty Information Section (Page 15)

pureAir Active HEPA+ ROOM

· Model: ........................1X5825

· Unit Dims: .........10.6” * 10.6” * 17.5”

........26.9cm * 26.9cm * 44.5cm

· Unit Weight: ...........11.5 lb (5.2kg)

· Electrical Input: ..... 120VAC / 50~60Hz

· Power Consumption: ........... 36W

· Decibel Level: . . . . . . . . . . . . . . .26-53dB

· Unit Warranty: .............10 Years*

Need information on something you can’t find in this manual?

Use this QR Code to view our troubleshooting guide.

pureAir Active HEPA+ PRO

· Model: .........................1X5826

· Unit Dimensions: ....11.3” * 11.3” * 24.0”

..........28.7cm * 28.7cm * 60.9cm

· Unit Weight: ............14.5 lb (6.6kg)

· Electrical Input: ......120VAC / 50~60Hz

· Power Consumption: .............62W

· Decibel Level: . . . . . . . . . . . . . . . . 26-53dB

· Unit Warranty: ...............10 Years*

Warranty Information

Your pureAir Active HEPA+ is warranted to be free from all defects in material and workmanship in normal

household use for a period of 10 years from date of purchase. This warranty is conditional to yearly

maintenance requirements, which include: 1. Yearly HEPA filter replacement. 2. Yearly BPI brush replacement

(provided free to anyone who has registered their Active HEPA+ product). 3. Replacement of PCO cell every

24 months (see pages 11-13 of this Owner’s Manual). The warranty is granted only to the original purchaser

and members of his or her immediate household. The warranty is subject to the following provisions: Any

damages or malfunctions caused by negligence, abuse, or use not in accordance with the Owner’s Manual

are not covered by this warranty. Likewise, any defects or damages caused by unauthorized service are not

covered. Greentech Environmental will, at its option, repair or replace a defective Air Purifier that is covered

by this Warranty. As a matter of warranty policy, Greentech will not refund the customer’s purchase price. To

obtain warranty service you must return the defective Air Purifier along with proof of purchase to the pureAir

Authorized Warranty Station. All transportation charges on parts, or units, submitted under this Warranty shall

be borne by the purchaser. Unless this Warranty is expressly renewed or extended by Greentech Environmental,

any repaired or replaced part of unit shall be warranted to the original purchaser only for the length of the

unexpired portion of the original warranty.

Further Limitations and Exclusions Are as Follows:

Any warranty that may be implied in connection with your purchase or use of the Air Purifier, including any

warranty of merchantability or any warranty for Fitness For A Particular Purpose is limited to the duration of this

warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations

may not apply to you.

Your relief for the breach of this warranty is limited to the relief expressly provided above. In no event shall

Greentech be liable for any consequential or incidental damages you may incur in connection with you

purchase or use of the Air Purifier. Some states do not allow the exclusion or limitation of incidental of

consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you

specific legal rights, and you may also have other rights which vary from state to state.

Registration

Please register your new pureAir Active HEPA+ product within 10 days of purchase by visiting

greentechenv.com/warranty or scanning the QR code to take you to the site.

Lifestyle IMG

FRESH AIR

STARTS

HERE

Greentech-pureAir-Active-HEPA-Plus-Owners-Manual-v3-220301

GreenTech Pro and Room Owner's manual

Related papers

Other documents