Cullmann D 4500 Owner's manual

Category
Camera flashes
Type
Owner's manual

This manual is also suitable for

14 15
ENG
Congratulations on purchasing your CULLMANN flash unit.
This D 4500 electronic flash unit has been manufactured for
digital and analog cameras using the latest technology in
accordance with the high quality standards of CULLMANN
products.
Please read the instructions carefully and follow their guidelines
so that you can enjoy the full range of possibilities of your flash
unit.
We would like to ask you to do your part in protecting the
environment by refraining from throwing used batteries or
rechargeable batteries into normal household trash; instead
please dispose of them at your photographic equipment
dealership or in specially designated waste.
16 17
Legende:
1. LCD display
2. Auto Check Indicator
3. Mode setting display
4. Beeper display
5. Energy level setting
6. Removal display for
the flash area
7. Circuit off display
8. Zoom position
9. Film sensitivity display
10. F-Stop Indicator
11. Mode button
12. Film sensitivity button
13. F-Stop Selector
14. Beeper on/off
15. Zoom button
16. LCD light
17. Ready / Test light
18. Electricity ON / OFF switch
19. Slave on/off
20. Auto OK
21. Mode indicator (N only)
ENG
ENG
Reflection plate
Diffuser
Flash head
Battery compartment lid
Reception sensor
Red AF light
Closing ring
Mounting foot
(type C, N and P)
Socket for updating
(except type P)
Auto Focus/TTL Flash Unit for:
C – Canon SLR & digital cameras (E-TTL)
N – Nikon auto focus SLR & digital cameras (TTL and i-TTL)
O/P – Olympus auto focus digital & digital single-lens reflex cameras
& Panasonic digital single-lens reflex cameras
S – Sony Alpha digital single-lens reflex (DSLR) cameras/
Konica Minolta auto focus SLR and digital cameras
(ADI and D lenses)
P – Pentax digital single-lens reflex (DSLR) cameras (TTL and P-TTL)
For type N, O/P, S
Mounting foot type S Mounting foot type O/P
For type C
For type P
Nikon i-TTL only: When you are using the option „3D-Matrix”,
the information “BL” will be displayed on the LCD screen
18 19
ENG
ENG
Special Features
• LCD display
• Automatic and manual zoom of 24-28-35-50-70-85 mm
• Red light ray as a focusing aid for setting the AF in low light
• TTL measurement
• Automatic speed setting for the shutter
• 5 energy levels, ratios 1/1, 1/2, 1/4, 1/8 and 1/16
• Readiness display for the flash in the seeker
• Synchronization of the foreground and background light
• Reduction of the red-eye effect (for Nikon and Olympus)
• Integrated slave function
• Integrated reflection plate and diffuser
• Energy-saving function
• Can be updated (except type P)
Inserting the Batteries
Ensure that the main switch is in the “OFF”
position. Push the lid of the battery compart-
ment forwards and swing it upwards. Insert the
batteries according to the corresponding symbols
for “+/-“.
Close the battery compartment lid and push it
back into its place until it clicks. Ensure that all
batteries are of the same type and are equally
charged; NiCd or NiMh rechargeable batteries are
preferable.
Mounting the Flash Unit onto the Camera
Switch off both the flash unit and the camera.
Turn the knurled screw of the flash unit upwards
toward the flash unit. Push the flash unit into
the camera’s device shoe. Turn the flash unit’s
knurled screw toward the camera, clamping the
flash unit to the camera.
For type S: Insert the mounting foot of the flash
unit into the device shoe of the camera. This
clicks the flash unit into place.
For type O/P: Insert the mounting foot of the
flash unit into the device shoe of the camera and
press onto “LOCK” in order to click the flash unit
into place.
Removing the Flash Unit from the Camera
Switch off both the flash unit and the camera.
Turn the knurled screw of the flash unit upwards
toward the flash unit. Remove the flash unit from
the device shoe of the camera.
For type S: Press the button that releases the
device shoe and remove the flash unit, pulling it
toward the rear.
For type O/P: Push both side of the lock/release
button in the directions specified and remove the
flash unit, pulling it toward the rear.
Activating the ON/OFF switch and Con-
ducting a Flash Test
In order to switch on the flash unit, push the main
switch into the “ON” position. As soon as the
camera is ready to be used, “READY” illuminates
on the readiness display.
Press the test button in order to check whether
the flash unit is operating correctly. If the flash
unit has lost its charge, wait until the “READY”
display illuminates again.
Push the main switch into the “OFF” position in
order to turn off the device.
LC Display Illumination
The LCD display serves in providing general
information about the camera and the current
state of the flash unit; every time the “LIGHT”
button is pressed, the LCD display will illuminate
for around 5 seconds.
Photographing, AF / TTL Operation
Automatic control of the flash
synchronization speed
When the flash unit is ready, the camera automa-
tically switches into the flash mode synchroniza-
tion speed. The synchronization speed depends
upon the camera model and is generally between
1/30 seconds and 1/250 seconds. If a photo has
been taken with the flash, the LCD display briefly
illuminates the “OK” symbol to confirm the
correct lighting.
20 21
ENG
ENG
“AF” Measurement Flash for Auto Focus
The red “AF” light ray integrated into the flash
unit supports the automatic focus setting of the
auto focus TTL cameras. When the lighting con-
ditions on hand are insufficient for the automatic
setting of the focal width, the flash unit projects
a red light ray onto the object as soon as the
camera shutter is touched slightly. Then the auto
focus of the camera adjusts to the object with the
help of the red light ray.
TTL (Through the lens) Flash Control
The flash unit receives its information solely
from the connected TTL-controlled camera. The
measurement of the lighting in TTL mode (TTL
= ‘through the lens’) is conducted by the camera
sensor.
This sensor measures the light that reaches the
camera. An electronic control circuit inside the
camera forwards a stop signal to the camera as
soon as the light is received; TTL mode means
that all factors influencing the exposure (such
as filters, changes in the shutter or zooms with a
variable shutter) are taken into consideration. You
don’t have to concern yourself with the setting
of the light emission. The camera’s electronic
system automatically guides the necessary light
quantity. Additionally, you can use measurement
devices (e.g., spot, matrix or centered lighting
measurement) that are provided in some came-
ras. To activate the TTL flash mode, gently tap
the mode selector into the TTL position. The LCD
display then shows “TTL”.
For Type C flash: The ETTL indicator will light
while connected to a ETTL camera.
For Type N flash: The LC Display will show TTL,
ITTL or BL in different way while connected to
different camera models. Please refer to the
camera´s manual.
Manual Flash Mode with Full Light
Emission
In order to use the flash unit with the full light
emission, the mode selector must be placed into
the M position (Manual). Then, every time the
flash unit is activated, a flash with full energy
takes place. The LCD display automatically provi-
des the distance necessary for the correct lighting
between the flash and the object. Adjustment
to the individual shooting situation can be done
by resetting the lens shutter or the focal width
(on the camera). 5 levels can be selected for
the “Energy Ratio”, 1/1, 1/2, 1/4, 1/8 and 1/16, by
lightly tapping the mode selector when it is in the
“M” position.
Synchronization of the Foreground and
Background Lighting
The flash unit supports the synchronization of
foreground and background lighting: Simply
activate the Front or Rear mode.
Canon, Nikon, Olymus, Panasonic and Sony
Alpha cameras control the synchronization of the
foreground and background lighting automati-
cally, making it unnecessary to adjust the settings
on the flash unit.
Swiveling Vertical/Horizontal Flash
Photos to be taken with a full flash are easily
recognizable due to their hard, dense shadows.
This is often accompanied by a sharp decline of
the foreground in the direction of the back-
ground. This phenomenon can be prevented
with a swiveling flash. Because the diffused light
creates a soft, equally distributed reproduction
sharpness, the reflector is turned upwards by
up to 90° so that the flash is returned by an ap-
propriate reflection surface. For color shots, the
reflection surface must be white or have a neutral
color and be unstructured. When swiveling the
reflector, ensure that no light falls directly from
the reflector onto the object. When you use the
swiveling flash, the zoom position clicks onto
50 mm, except in Manual mode.
In order to have your pictures correctly exposed
using bounce or swivel flash, the following is
recommended to users:
(1) Select white or reflective surfaces to bounce
the light off. Otherwise your pictures will come
with an unnatural color cast similar to that of the
reflecting surface.
(2) Set the camera´s exposure mod to Aperture
Priority Auto (”A”) or Manual (”M”).
(3) Use a wider aperture than normally do, as 2 or
3 stops of light can be lost when using bounce or
swivel flash.
22 23
Reflection Plate and Diffuser
The flash unit has an integrated reflection plate
and a diffuser. You can slide out the reflection
plate or the diffuser on the upper side, swivel the
flash head and use the reflection plate to shoot
photos with a heavy effect. The diffuser can
reduce the strong light, creating soft effects.
Using the diffuser is recommended to achieve
ideal results at close proximity (1 – 3 yards).
Energy-Saving Function
To save electricity, the flash unit automatically
switches off approximately 3 minutes after it has
been switched on or since the most recent flash
was released. The LCD display indicates the
“OFF” signal. To reactivate the flash unit, simply
press any button switch below the LCD display
table or switch the main switch off and back on.
The flash unit is not full switched off in the
energy-saving function setting, but its energy use
is drastically reduced. When you are no longer
using the flash unit, set the main switch to “OFF”.
ENG
ENG
Power-Zoom
Automatic control of the motorized zoom
When using zoom lenses that transmit their focal
widths to the camera, the camera forwards this
information to the flash unit. Then the flash unit
automatically adjusts its zoom position. The
automatic reflector control of the motorized zoom
is possible with cameras that permit the digital
transmission to the flash unit.
The LCD display on the flash unit indicates zoom
positions of 24-28-35-50-70-85 mm. When the
flash unit is switched on, the zoom is activated
and the position is set at 35 mm. As soon as the
camera’s release is touched only slightly, the focal
width of the flash unit is automatically adapted to
the focal width of the lens.
Whenever the flash head is not at the normal set-
ting (pointing forwards) whereby it is in another
position, the zoom position clicks to 50 mm and
is indicated in the LCD display by a short flash in
the Auto mode.
Manual Control of the Motorized Zoom
With the “Zoom” button, you can alter the
reflector position of the zoom independently
of the focal width of the lens. The LCD display
then indicates “M” and the current setting of the
reflector’s zoom position.
Light tapping of the “Zoom” button changes the
zoom position in this order: 24-28-35-50-70-85 mm.
Receiver Function
This flash unit can be operated as a wireless re-
ceiver by setting the switch “Slave Mode” to the
S position. The flash unit switches automatically
to the M mode with an energy ration of 1:1 and a
focal width of 24 mm. When the sensor discovers
the release of an extreme flash, the flash is
released simultaneously. The quantity of the light
emission can be selected by setting the energy
ration from 1/1 to 1/8. If several flash units
are used as receivers, then the corresponding
quantity of light must be taken into consideration
in order to calculate the correct lighting. If the
reception mode is activated, the energy-saving
mode does not operate.
24 25
Technical Data
Guide number (ISO 100) 36 at 85 mm
Reflector with motorized zoom 24-28-35-50-70-85 mm
Energy supply 4 x 1.5 V NiCd or NiMh batteries
Flash times 1/1,000 – 1/20,000 seconds
Charging Time 0,5 – 9 seconds
Number of flashes approximately 80 times with new
NiCd or NiMh batteries (according
to the battery performance)
Color temperature Daylight
Dimensions approximately 175 x 74 x 59 mm
Net weight approximately 270 grams
(without batteries)
Technical alterations reserved.
* With Minolta Dynax 3 and 5, switch the WL setting on
the function selector to the ON position prior to using the D 4500.
ENG
Update for the D 4500
To maintain your flash unit always in line with the
state of the art, you can update your CULLMANN
D 4500 to the current state (except type P).
As the update concerned can only be carried out
at our service department, please send your
flash unit to:
CULLMANN GmbH
Service Blitzgeräte
Waldstraße 12
90579 Langenzenn, Germany
The update for the D 4500 is free of charge.
If you require more information on the possibility
of updating the D 4500 flash unit, please send an
Safety Instructions
• Never use a flash in direct proximity to the eyes
of people or animals. This can damage the
retina and even lead to blindness.
• Only use energy sources specified in the usage
instructions.
Never attempt to open or short-circuit batteries.
Never expose batteries or rechargeable batte-
ries to increased temperatures such as intensive
sunlight or fire.
Always switch off the flash unit before changing
the batteries.
Do not attempt to open the flash unit, as it is
under high voltage. There are not parts inside
the flash unit that can be repaired by the user.
In the event that the flash unit is damaged to
the extent that internal parts are exposed, then
the flash unit may only be used again after it
has been repaired. Remove the batteries so that
it cannot be used unintentionally.
• Never attempt to repair the flash unit yourself.
In the event of problems, contact our Customer
Service.
ENG
28 29
Légende:
1. Affichage LCD
2. Affichage autotest
3. Affichage du réglage
du mode
4. Affichage du bip
sonore
5. Réglage du niveau
d'énergie
6. Affichage de la
distance pour la zone
couverte par le flash
7. Affichage du courant
OFF
8. Position du zoom
9. Affichage de la
sensibilité du film
Plaque réfléchissante
Diffuseur
Tête de flash
Couvercle du
compartiment à piles
Capteur de réception
Lumière rouge
Anneau de fermeture
Pied de montage
(Type C, N et P)
10. Affichage du diaphragme
11. Touche de mode
12. Touche de sensibilité du film
13. Touche du diaphragme
14. Bip sonore Marche /Arrêt
15. Touche zoom
16.
Éclairage LCD
17. Voyant Ready /Test
18. Bouton courant ON/ OFF
(Marche /Arrêt)
19. Slave on/off
20. Auto OK
21. Indicateur de mode
(seulement N)
FRA
FRA
Nikon i-TTL: Si vous utilisez l´option “3D-Matrix”
l`écran LCD affiche l`information “BL”.
Pour type C
Pour type P
Jack pour actualisation
(sauf type P)
Auto Focus/Flash TTL pour:
C – Canon auto focus SLR & digital cameras (E-TTL)
N – Nikon auto focus SLR & digital cameras (TTL and I-TTL)
O/P – Olympus & Panasonic DSLR
S – Sony Alpha DSLR/ Konica Minolta auto focus SLR and digital
cameras (ADI and D lenses)
P – Pentax DSLR
Pour type N, O/P, S
Pied de fixation type S Pied de fixation type O/P
64 65
Legenda:
1. LCD-scherm
2. Zelftestindicator
3. Indicatie van de
modusinstelling
4. Indicatie van de
pieper
5. Instelling van het
energieniveau
6. Afstandsindicator
voor het flitsbereik
7. "Stroom uit"-
indicator
8. Zoompositie
9. Filmgevoeligheids-
indicator
Reflecterende plaat
Diffusor
Flitskop
Deksel van het batterijvak
Ontvangstsensor
Rood AF-licht
Sluitring
Montagevoet
(type C, N en P)
10. Diafragma-indicator
11. Modusknop
12. Filmgevoeligheidsknop
13. Diafragmaknop
14. Pieper aan/uit
15. Zoomknop
16.
LCD-verlichting
17. Ready/test-lampje
18. Schakelaar stroom on/off
19. Slave on/off
20. Auto OK
21. Mode indicator
(alleen type N)
NIE
NIE
Nikon i-TTL: In het display verschijnt de melding "BL", als op
de camera het belichtingstype "3D-Matrix" is gekozen.
Contact voor update
(behalve type P)
Autofocus-/TTL-flitser voor:
C – Canon autofocus SLR- en digitale camera‘s (E-TTL)
N – Nikon autofocus SLR en digitale camera‘s (TTL en i-TTL)
O/P – Olympus auto focus digital & digital single lens reflex camera‘s
& Panasonic digital single-lens reflex (DSLR) camera‘s
S – Sony Alpha digital single-lens reflex (DSLR) camera‘s/ Konica
Minolta autofocus SLR- en digitale camera‘s (ADI- en D-lenzen)
P – Pentax digital single-lens reflex (DSLR) camera‘s (TTL and P-TTL)
Voor type N, O/P, S
Flitsvoet type S
Flitsvoet type O/P
Voor type C
Voor type P
www.cullmann-foto.de
CULLMANN
Foto·Audio·Video GmbH
90579 Langenzenn • Germany
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38

Cullmann D 4500 Owner's manual

Category
Camera flashes
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI