Catalina 970822 User manual

MODEL #: 20745-000

5.

1.

This lamp is approved for indoor use only.

2.

Avoid laying objects directly over the power supply

cord to avoid cutting or damaging the wire.

Do not install non-factory wiring or any other

electrical components. Altering or modifying

the lamp in any way will render the product

unsafe.

Keep curtains, shades, wall hangings and all

other fabrics and objects away from the lamp,

lamp switch and light bulb. Lamps are not

designed to support additional weight.

Place the lamp on a stable, level surface in an

area where the lamp will not be tipped over or

bumped.

3.

4.

1. To clean: use a soft, dry cloth only.

2. Do not use chemical or abrasive cleaning solutions.

BULB REPLACEMENT

1. Turn off and unplug the lamp and allow bulb to

cool before replacing bulb.

2. Light bulb should never touch the lamp shade.

DO NOT EXCEED RECOMMENDED BULB

WATTAGE.

Read and Save:

IMPORTANT SAFETY INSTRUCTIONS

1. Use one 150 Watt Maximum, 3-way type A bulb

or CFL or LED equivalent (Bulb not included).

2. Integrated LED bulb replacement not required.

CLEANING AND MAINTENANCE

For Customer Assistance:

www.evolutionlightingllc.com

Made In China

LED ÉTAGÈRE FLOOR LAMP

20:55

自动

星期一星期二星期三星期四星期五

ъ

For Customer Assistance:

www.evolutionlightingllc.com

Made In China

ASSEMBLY INSTRUCTIONS

1. Carefully unpack and lay all parts on a clean, level, protected

surface so as to prevent any damages to the finish during assembly.

2. Assemble bottom supporting shelf (G) . See Fig 1

a. Remove the pre-assembled screws (G3) from shelf half (G2).

b. Align shelf halves G1 and G2 so the upright leg holes are on the same

plane and insert ends of G2 into G1 and secure with screws G3.

3. Assemble the lampbody: See Fig 2.

Note: Gently pull the power cord through the four tubes and

the shelf holes during assembly.

a. Insert and thread the four leg sections (E1) to the four leg stubs of

the socket assembly (D).

b. Insert and thread the four leg sections (E2) to the four leg sections (E1).

c. Insert and thread the four leg sections (E3) to the four leg sections (E2).

d. Insert support shelf (G) onto the four leg sections (E3) and secure with

leg feet (F). The leg hole openings on shelf (G) should face the bottom.

4. Attach one end of each chain section (J) to each of the four holes on

the flower pot (I).

Attach the upper portion of each chain section (J) to the desired height

on the leg assembly (D) making sure the flower pot (I) is level.

Note: Maximum weight capacity of flower pot (I) with plant and water

should not exceed 12 lbs.

5. Place the plastic tray (H) on the shelf (G).

6. Install the light bulb (not included) into the socket assembly (D).

7. Pinch and insert the harp (C) into the the harp fittings on the

socket assembly (D). Slide the caps on the harp (C) over the fittings

on the socket assembly (D) to secure.

8. Assemble the shade (B): See Fig 3.

a. Hold shade (B1) upside down with the small opening of the shade

resting on a flat,hard surface.

b. Insert the closed end of the U shaped shade frame (B2) so it seats

on the inside of the shade (B1) top opening and stretch shade

upwards until the stubs on the shade frame (B2) can be inserted

into the tubes on shade (B1) bottom rim.

9. Remove the finial (A) from the harp (C), place the shade (B) onto

the harp (C) and secure with finial (A).

10. Insert the plug into an electrical outlet.

11. Use the rotary switch on the socket assembly (D) to adjust uplight

from low, medium, high, and off intensity.

12. Use the timer on the socket assembly (D) to adjust how much grow

light your plant will require.

Note: Please charge at least 6 hours before using the timer.

A

B

C

D

J

I

H

G

F

For Customer Assistance:

www.evolutionlightingllc.com

Made In China

B

B1

B2

G1

G2

G3

G

D

E1

E2 E3

F

FIG.1

FIG.3

FIG.2

Lamp Body Assembly

Shade Assembly

Bottom Support Shelf

20:55

33

自动

ъ

For Customer Assistance:

www.evolutionlightingllc.com

Made In China

Please read the instruction carefully before using it, and keep this

Instruction Manual.

1. Keyboard Lock

Hold the “C/R (Clear / Reset)” button for more than 3 seconds until “ ”

appears. Repeat to Unlock.

2. Setting the Current Time

While holding the “(Clock)” button, press “H+” to adjust the Hour,

“M+” to adjust the Minute, and “D+” to adjust the day settings.

3. Timer Setting

(1) Set up of the first Turn On: press “ (Program)”, the bottom left of

the screen will show “1ON”. Use “H+”, “M+”, and “D+” keys to set the

time of Turn On. To turn on at the same time every day, please

choose “MON TUE WED THU FRI SAT SUN”.

(2) Set up of the first Turn Off: press “ (Program)” again, the bottom of

the screen will show “1OFF”. Use “H+”, “M+”, and “D+” keys to set

the time of Turn Off. To turn off at the same time every day, please

choose “MON TUE WED THU FRI SAT SUN”.

(3) Continue to press “ (Program)” to set additional time periods. Up to

20 ON/OFF periods can be set. The screen will show 2ON, 2OFF,

3ON, 3OFF…..20ON, 20OFF. Press “ (Program)” again to end

timer setting and return to clock display.

(4) To Check the Timer Setting, press “ (Program)” to check if time is

correct. Press “(Clock)” to finish.

(5) Press “MANUAL” to turn power on and adjust automatic setting.

*Press “MANUAL” to Turn On. Display will show “ON”.

*Press “MANUAL” to Turn Off. Display will show “OFF”.

*Press “MANUAL” to Turn On, then press “AUTO”. The device is

on and in automatic state. Will automatically turn on and off per

the Timer Setting.

*Press “MANUAL” to Turn Off, then press “AUTO”. The device is

off and in automatic state. Will automatically turn on and off per

the Timer Setting.

Example: The unit turns on at 18:00 every day, and turns off at 07:00 the

next day.

A: Follow (1) to program screen as shown in Picture 1a.

B: Follow (2) to program screen as shown in Picture 1b.

C: Follow (4) to check settings.

D: Follow (5) Press to display “OFF”, then press to display “AUTO”.

Troubleshooting

If the timer does not work properly once

plugged in:

1. Check “Timer Setting” and follow setup

directions. Make sure time and date is

set correctly.

2. Check “Timer Setting”, make sure D+

setting is for correct days. For every day

use, the setting must display “MON TUE

WED THU FRI SAT SUN”.

3. Check “Timer Setting” and follow step (4).

Check for any incorrect programmed time

periods and remove.

4. Press and hold “C” to initiate a reset of

the Timer.

This will restore the factory defaults.

Timer Operation Manual

Operating Instructions

Picture 1a Picture 1b

Selecting Your Plant

Planting & Watering

The GloGro is designed to support a wide range of small to medium-sized plants.

This includes most flowers, vegetables, herbs, small shrubs, and other smaller indoor plants.

The GloGro may not be suitable for large shrubs, trees, bushes, and other large indoor plants

beyond the seedling or juvenile stages.

The maximum height for a plant within the GloGro system is 3 feet from bottom of pot to top of plant.

Once you have selected your plant, you will need to decide upon the appropriate pot type.

We have provided a hanging pot and chain that will allow you to plant a small-medium sized plant.

If you plan on growing something larger, such as a full sized tomato plant, you will want to use a

larger pot to ensure proper nutrients and a full root system.

Most plants are happy to be watered daily. Do not over-water a plant, as you risk causing the roots

to rot. The hanging pot is designed with an integrated drip pan to collect excess water, but care

should still be taken to avoid too much water. Any pot used should have a drip pan or small holes

and a tray to allow the excess water out of the soil.

Amount of Light

Different plants require differing levels of light for healthy growth. The GloGro integrated timer

can make sure your plant receives the right amount of light consistently every day.

Many Nurseries and Home Garden Centers provide an information card or insert that will tell you

the sunlight and watering requirements. Depending on the amount of light needed, the following

tables can help you set the GloGro to deliver the right amount.

Full Sun: Full Exposure, High Energy Requirements

12-18 Hours/Day

Can Sustain High Temperatures

Partial Sun: Partial Exposure

8-12 Hours/Day

Can Sustain High Temperatures

Partial Shade

8-12 Hours/Day

Maximize Distance from Plant to Light

Require Lower Temperatures, More Heat Sensitive

Full Shade

4-8 Hours/Day

Maximize Distance from Plant to Light

Require Lower Temperatures, More Heat Sensitive

Tomatoes

Peppers

Peas

Beans

Cucumber

Squash

Sunflower

Marigold

Verbena

Aster

Hibiscus

Lavender

Full Sun:

Carrots

Beets

Cilantro

Garlic

Kale

Lettuce

Parsley

Broccoli

Cauliflower

Lettuce

Asparagus

Partial Sun/Shade:

Hydrangea

Amethyst

Begonia

Caladium

Flowering Maple

Bleeding Hearts

Most Indoor House Plants

Full Shade:

Growth Stages: Seed & Germination

During the Seeding Stage, water is the critical element required for germination and growth.

Seeds need to be given water to soften and sprout, then planted 1/2 to 1 inch deep, with the

sprout upward. During this phase, the seed does not require a lot of light and should not be

kept too close to the light source. Excessive light can burn the plant out.

Growth Stages: Vegetative Growth

This stage begins once roots and leaves have taken form. Now, the primary source of energy for the

plant is harnessed from light. Nutrients are collected by the root system. During this stage, you can

increase the amount of light provided up to the full amount recommended for that plant type.

Growth is focused on leaves, stems, and the main stalk. Once the plant reaches maturity, it may

begin to flower and fruit.

Growth Stages: Flowering & Fruiting

During this stage, the plant will begin to flower and bear fruit. Some plants will not start this stage

until they sense a change in the season. For this reason, you may need to reduce the duration in

which you provide light for the plant to start flowering.

You may need to stimulate the pollination of your flowers for them to successfully fruit. In nature,

bees, other insects, and wind will help pollinate flowers. In your home, you may need to use a

small brush, small rod, or other means to help activate the pollination process.

GloGro Quick Tips

Select a soil that is specifically for flowers and vegetables.

Keep seedling and juvenile plants further from the grow light source to protect against excessive

exposure. Once the plant is established, you may move the plant closer.

For large vegetables and plants, use a larger pot with sufficient nutrients. You may also use the

smaller hanging pot and then transfer to the larger pot as the plant grows.

Water Daily! Do NOT over water.

Use the integrated timer to set a consistent schedule.

Make sure to assist in pollination. Gently shake or brush flowers to stimulate self-pollination.

Page is loading ...

Consumer Service

Service d’aide aux Consommateurs

Servicio al Consumidor

http://www.evolutionlightingllc.com

LIMITED WARRANTY

EVOLUTION LIGHTING warrants all of its lighting fixtures against defects in materials and workmanship for one (1) year from the date of

original purchase. Electronic parts including passive infrared devices, photoelectric switching mechanisms, and light bulbs provided with

Evolution Lighting products are warranted for 30 days from the date of original purchase.

ENERGY STAR qualified product, which include GU24 Energy Star qualified bulbs, are warranted for repair or replacement of defective

parts of the luminaire housing, mounting hardware, optics, ballast and trim for three (3) years from the date of purchase. GU24 based

integrated lamps included with the luminaire, carry a three (3) year warranty.

ENERGY STAR qualified Solid State product with replaceable components warrants the replaceable components for three (3) years.

ENERGY STAR qualified Solid State product with non replaceable components is warranted for five (5) years.

This warranty does not cover parts becoming defective due to misuse, accidental damage, improper handling and/or installation and

specifically excludes liability for indirect, incidental or consequential damages. Product found to be defective may or may not be replaced

with same or like type product, contingent on the nature of the defect, and or replacement availability and or compensated for at a pro rated

value. This warranty gives you specific rights and you may also have other rights, which vary from state to state. Proof of purchase is

required to exercise the warranty

.

GARANTÍA LIMITADA

EVOLUTION LIGHTING garantiza todas sus luminarias contra defectos de material y mano de obra por (1) año a contar de la fecha

original de compra. Las piezas electrónicas, lo que incluye dispositivos infrarrojos pasivos, mecanismos de conmutación fotoeléctrica, y

bombillas que vengan incluidas con el producto Evolution Lighting, están garantizadas por 30 días a contar de la fecha original de compra.

Los productos calificados por ENERGY STAR, lo que incluye bombillas GU24 calificadas por Energy Star, están garantizados por tres (3)

años a contar de la fecha de compra y serán repara dos o cambiados si la caja de la luminaria, el equipo de montaje, la óptica, el

balastro o las molduras tienen piezas defectuosas. Las bombillas integradas con base GU24 que vienen con la luminaria, están

garantizadas por tres (3) años.

Los repuestos para productos en estado sólido calificados por ENERGY STAR están garantizados por tres (3) años.

Los productos en estado sólido calificados por ENERGY STAR que no contengan repuestos están garantizados por cinco (5) años.

Esta garantía no cubre las piezas que tengan defectos debidos a su mal uso, a daños accidentales, y al manejo y/o la instalación

inapropiada de las mismas, y libera específicamente de toda responsabilidad por daños indirectos, casuales o consiguientes. Un producto

considerado defectuoso puede o no ser cambiado por otro producto idéntico o similar, dependiendo del tipo de defecto y/o a la

disponibilidad de un producto por el cual cambiarlo, y/o puede ser compensado a un valor prorrateado. Esta garantía le da derechos

específicos además de los cuales puede tener otros, los cuales varían entre estados. Se requiere un comprobante de compra para cobrar

la garantía.

GARANTIE LIMITÉE

EVOLUTION LIGHTING garantit tous ses luminaires de tout défaut en termes de matériel et de main-d’œuvre pendant un (1) an à compter

de la date d’achat d’origine. Les composants électroniques, incluant les éléments infrarouges passifs, les mécanismes d’interrupteur

photoélectriques et les ampoules fournies par les produits Evolution Lighting sont garantis 30 jours à compter de la date d’achat d’origine.

Les produits homologués ENERGY STAR, incluant les ampoules GU24 homologuées Energy Star, sont garantis pendant trois (3) ans à

compter de la date d'achat et seront réparés ou remplacés si le corps du luminaire, les pièces de montage, l'optique, le contrepoids et

la bordure sont défectueux. Les lampes intégrées à culot GU24, qui viennent avec le luminaire, sont garanties pendant trois (3) ans.

Les produits à état solide homologués ENERGY STAR qui ont des composants remplaçables, ont leurs composants remplaçables

garantis pendant trois (3) ans.

Les produits à état solide homologués ENERGY STAR qui ont des composants non remplaçables sont garantis pendant cinq (5) ans.

Cette garantie ne couvre pas les pièces qui deviennent défectueuses en raison d’une mauvaise utilisation ou manipulation, d’un accident

et/ou d’une installation incorrecte. Elle exclut spécifiquement tout risque d’endommagement consécutif ou indirect. Un produit découvert

défectueux sera ou non remplacé par un produit identique ou similaire, selon la nature du défaut et/ou la disponibilité du remplacement,

et/ou sera compensé à une valeur au pro rata. Cette garantie vous donne des droits spécifiques, et vous pouvez également avoir d’autres

droits, qui varient selon les états. La preuve d’achat est exigée pour exercer le droit à la garantie.

Catalina 970822 User manual

This manual is also suitable for

Catalina 970822 User manual

in other languages

Related papers

Other documents