WINSOON GCM3737 Operating instructions

WINSOON
Brand
WINSOON
Model
GCM3737
Type
Operating instructions

This manual is also suitable for

WINSOON GCM3737 is a barn door hardware kit that allows you to install a sliding barn door in your home. The kit includes all the necessary hardware, including the track, hangers, floor guides, and door stoppers. The track is made of steel and is 11 feet long. The hangers are made of steel and have a weight capacity of 220 pounds. The floor guides are made of nylon and help to keep the door in place. The door stoppers are made of rubber and help to prevent the door from hitting the wall.

WINSOON GCM3737 is easy to install and can be completed in a few hours.

WINSOON GCM3737 is a barn door hardware kit that allows you to install a sliding barn door in your home. The kit includes all the necessary hardware, including the track, hangers, floor guides, and door stoppers. The track is made of steel and is 11 feet long. The hangers are made of steel and have a weight capacity of 220 pounds. The floor guides are made of nylon and help to keep the door in place. The door stoppers are made of rubber and help to prevent the door from hitting the wall.

WINSOON GCM3737 is easy to install and can be completed in a few hours.

Installation Manual
Barn Door Hardware
www.winsoonhardware.com
Track Accessories
Chart: Track Junction
Check the quantity of all the accessories.
Any product problems or installation questions, please email us at
[email protected] with your “order ID”.
Main Installation Dimension
※Hardware Installation
11FT
8 82 2
2 1 1
2 1
Steel Hanger
Door Stopper
Anti-jump
Pad
Floor guide
Floor guide
Junction
Plate
Single Door Hardware Kit Includes
Part Name
Flat Track
picture
Lag Bolt Spacer
Type A Type B
1
door hight + 1-11/16” (43mm)
3/8”(10mm)
1-5/16’’(33mm)
8” 16” 16” 16” 10”
11FT
16” 16” 16”10” 8”
Step 1: Connect your tracks first with junction plate.
Step 2: Measure the overall height for the center line of the
track, make sure it shouldbe door height + [1-11/16
(43mm)] above the floor.
Mark out all the holes’position according to your track.
2
door height + 1-11/16” (43mm)
16”
16”
16”
16”
16”
Step 3: Drill holes and install your track
Concrete wall: Drill out the holes by using a dril
with 3/8” (10mm)drill bit.
Wooden wall: Drill out the holes by using a drill
with 1/4” (6mm) drill bit.
Install the track refer to the below image.
Step 4: If you use type A floor guide , you will need to
open a slot [5/16” (7mm) wide, 3/4” (20mm) deep] at
the bottom of the door with a slotting machine.
If you use type B floor guide , please skip this
step.
5/16”(7mm)
3/4”(20mm)
3
Concrete wall
Wooden wall
Step 5: Install hangers on your door.
Step 6: Install anti-jump pad. As the picture shows, the screw is
near the edge of your door.
4
1-7/8“
(48mm)
3-9/16”
(90mm)
2-3/8”~3-15/16”
60mm-100mm
(recommend)
φ3/8” (10mm)
Step 7: Put your hangers on the track, then twist the anti-jump
pad facing to your wall.
Step 8: Install your floor guides.
5
φ1/4” (6mm)
Type A
Step 9: Adjust and fix stoppers to make the door not detach from
the floor guide whether the door on close or open position.
6
φ1/4” (6mm)
Type B
Usage Statement:
Use of excessive force when opening, and closing,the door(s) may result in damage to the
hardware. Always hold the handle and gently open and close the door(s).
• Failure to wear proper safety gear (i.e.,eye protection) may result in serious injury or
death. Always wear proper safety gear before using power tools.
• Improper operation of power tools may result in loss of control, serious injury or death.
Always ensure you have complete control of the power tool and the work area is free of
hazards before operatiog a power tool.
• Lack of secure clamping of the door may result in unexpected movement of the
door,loss of power tool control and serious injury or death. Always securely clamp the door
in place before cutting,or drilling, the door.
• Lack of ,or improperly installed Anti-jump Disc may result in the door coming off the
track and cause serious injury or death. installation of Anti-jump Disks are required for safe
operation of this hardware. installed properly, these discs will keep the door securely
attached to the teack.
WARNING
• Mishandling of heavy objects (i.e.,doors) may cause a loss of balance and serious
injury. Always be sure you have a secure hold on the object and are balanced before
moving the object.Always wear safety shoes when lifting heavy objects.
• Getting body parts (i.e., hair,fingers) caught in moving parts may cause pinching and
serious injury.Do not put fingers in parts that may move and always remove or contain
anything on your body that may become entangled with a moving part.
• Closing sliding doors with your hand on the end of the door may result in your hand, or
fingers, getting caught between the door and other solid objects (i.e., another door, mold-
ing) causing serious injury. Always use the door handle to close doors.
CAUTION
5 year straight unconditional warranty service enables every single hardware’s durability
coverage during its life time.
Warranty Statement:
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

WINSOON GCM3737 Operating instructions

WINSOON
Brand
WINSOON
Model
GCM3737
Type
Operating instructions
This manual is also suitable for

WINSOON GCM3737 is a barn door hardware kit that allows you to install a sliding barn door in your home. The kit includes all the necessary hardware, including the track, hangers, floor guides, and door stoppers. The track is made of steel and is 11 feet long. The hangers are made of steel and have a weight capacity of 220 pounds. The floor guides are made of nylon and help to keep the door in place. The door stoppers are made of rubber and help to prevent the door from hitting the wall.

WINSOON GCM3737 is easy to install and can be completed in a few hours.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents