Bosch DL 0 607 460 001 Product information

4 . . . 8

9 . . . 13

14 . . . 19

20 . . . 24

25 . . . 29

30 . . . 34

35 . . . 39

40 . . . 44

45 . . . 49

50 . . . 54

55 . . . 59

60 . . . 64

65 . . . 69

Robert Bosch GmbH

Geschäftsbereich Elektrowerkzeuge

D-70745 Leinfelden-Echterdingen

3 609 929 393

00.05

Printed in Germany - Imprimé en Allemagne

DL 0 607 460 001

. . . 401

Page is loading ...

9

3 609 929 393 • 00.05

1 Tool holder

2 Collar

3 Clamping area

4 Right/Left rotation button

5 Hanging hoop

6 Exhaust air hose (combined)*

7 Air supply hose*

8 Hose connection piece

9 Lever

10 Auxiliary handle*

11 Air outlet with silencer of sintered metal

12 On-Off switch

13 Right/Left rotation switch

*Optional accessories

Not all the accessories illustrated or described are

included in standard delivery.

The machine is intended for the screwing in and

loosening of screws as well as for the tightening and

loosening of nuts in the specified dimension and

performance range.

Measured values determined according to EN 50 144

(Rated pressure).

The A-weighted sound pressure level of the tool is

typically 74 dB(A). The noise level when working can

exceed 85 dB(A).

Wear ear protection!

The typical hand-arm vibration is below 2.5 m/s

2

.

Insertion Tools

For the associated insertion tools, see the Bosch cata-

logues for pneumatic tools and accessories for

electro-tools.

Product Specifications

Pneumatic Torque Control Screwdriver

Order number 0 607 460 001 0 607 460 401

No-load speed [RPM] 900 750

Power output [W] 380 320

Maximum tightening torque [Nm] 1.5–10 1.5–10

Maximum screw diameter [mm] M 6 M 6

Rotational direction

Tool holder 1/4" 1/4"

Switch start – ●

Lever start ● –

Ratcheting clutch ●●

Rated pressure [bar/psi] 6.3/90 6.3/90

Hose connection fitting G 1/4" G 1/4"

Inside hose dia. [mm] 10 10

Air consumption under load [l/s] 10 7

Weight (without accessories) approx. [kg] 1.00 0.90

Product Elements

Intended Use

Noise/Vibration Information

Accessories

Auxiliary handle 3 602 025 007

Hose connection piece 3 603 386 000

Exhaust air hose (combined) 3 607 000 027

Exhaust air set (separate) 3 607 030 024

Special gearbox grease

225 ml

3 605 430 009

Type

0 607 460 001

0 607 460 401

DL_bu_3609929393_t.fm5 Seite 9 Donnerstag, 18. Mai 2000 12:29 12

10

3 609 929 393 • 00.05

Working safely with this machine is

possible only when the operating

and safety information are read

completely and the instructions

contained therein are strictly

followed.

In addition, the Section Safety

Instructions for Pneumatic Tools

must be observed.

Before using for the first time, ask

for a practical demonstration.

■ Disconnect the air supply.

Disconnect the air supply when the machine is not

in use, before maintenance work and for the

changing of the tools.

Check the direction of rotation setting

before operating the machine!

■ Keep hands away from the rotating tool holder as

well as the tool.

■ Use only flawless insertion tools that are not worn.

Defective insertion tools can cause injuries.

■ Pay attention to firm seating of the insertion tools!

■ Be careful in confined working conditions.

As a result of the reaction torque, injuries can occur

from squeezing or pinching.

■ Be careful when screwing in long screws; danger

of sliding off.

■ Place the machine on the screw/nut only when

switched off.

■ Secure the workpiece.

Use clamping devices or a vice to hold the

workpiece in place. In this manner, it is held more

securely than with your hand and makes possible

the operation of the machine with both hands.

■ Be careful of torque reaction!

For high torque settings and reduced operating

pressure, the clutch no longer disengages.

■ It is recommended that a auxiliary handle always be

used to reduce the danger of injury at high torques.

■ Bosch can assure flawless functioning of the

machine only when original accessories are used.

The supplied air must be free of foreign material and

humidity to protect the machine from damage,

contamination and rust.

The use of a pressurised air maintenance unit is

necessary.

All fittings, connecting lines and hoses must be

dimensioned for the required air pressure and volume.

Avoid restrictions in the air supply resulting from, e.g.,

pinching, kinking or stretching!

In case of doubt, measure the pressure with an

pressure gauge at the air inlet with the machine

switched on.

Maintenance Unit

The maintenance unit ensures fault-free functioning of

pneumatic tools.

It consists of three major components:

– Filter with water separator

– Pressure reduction valve with pressure gauge

– Mist oiler

Lubricant in the mist oiler: Motor oil SAE 10/SAE 20.

Do not use paraffin or diesel oil.

Adjust the mist oiler so that a thin film of oil collects on

the air outlet.

Observe the operating instructions of the maintenance

unit.

The machine operates optimally with a pressure of

6.3 bar (90 psi) measured at the air inlet with the

machine running.

Depending on the type of machine, actuate the

lever 9 or the on-off switch 12 several times before

connecting to the air supply.

Switching On/Off

If the machine does not start, e.g. after not being used

for a longer time, disconnect the air supply and turn

the tool holder 1 by hand. Adhesive forces are

eliminated in this manner.

For an interruption of the air supply or reduced

operating pressure, switch off the machine.

Check the operating pressure and start again

when the pressure returns to normal.

For Your Safety Air Supply

Putting into Operation

DL_bu_3609929393_t.fm5 Seite 10 Donnerstag, 18. Mai 2000 12:29 12

11

3 609 929 393 • 00.05

Type of Clutch

The machines have torque-dependent

ratcheting clutches that can be

adjusted over a wide range. They

respond when the adjusted torque is

reached.

Type 0 607 460 001

Lever Start with Ratchet Clutch

Switching on: Press the lever 9.

When the torque setting for the

screwing operation is reached, the

screwdriver disengages until the

lever 9 is released.

Switching off: Release lever 9.

When the lever 9 is prematurely released, the

torque setting will not be reached.

Type 0 607 460 401

Switch Start with Ratcheting Clutch

Switching on: Press the on/off switch 12.

When the torque setting for the

screwing operation is reached, the

screwdriver ratchets until the on/off

switch 12 is released.

Switching off: Release the on/off switch 12.

When the on/off switch 12 is prematurely

released, the torque setting will not be

reached.

Before performing any work on the machine

itself, disconnect the air supply.

Stick the tool inserts into the tool holder 1 until the

engaging of the detent is felt.

Setting the Torque

The desired tightening torque is set by turning the

collar 2.

Turning in the clockwise direction results in a higher

torque, in the counter clockwise direction, a lower

toque.

The collar 2 has a detent each quarter of a turn.

Caution!

For soft bolting actions, the clutch no longer

ratchets even for low torque settings.

After the adjustment

Adapt the torque by means of trial boltings for the

specific bolting action (hard, middle, soft). Check the

torque with an electronic torque measuring instrument

or a torque wrench.

For higher torques, a correspondingly greater

counter force is necessary.

With a clamping device in the area 3, this counter

force can more easily be counteracted.

Machines that are operated with a torque of > 4 Nm

(or > 7 Nm for machines with pistol grip) are to be

used with a clamping device or an auxiliary handle.

Take care that the auxiliary handle or the clamping

device holds the unit in a firm and secure manner.

Reversing Rotational Direction

Type 0 607 460 001

Right rotation: Right/Left rotation button 4 not

pressed.

Left rotation: Right/Left rotation button 4 pressed.

By turning the right/left rotation button,

the position is locked.

Type 0 607 460 401

Right rotation: Set the right/left rotation switch 13 to

the right.

Left rotation: Set the right/left rotation switch 13 to

the left.

Extraction of the Exhaust Air

Only type 0 607 460 001

Slide the exhaust air hose 6 over the air supply

hose 7. Mount the air supply hose 7 onto the hose

connection piece 8 and attach the exhaust air

hose 6 to the housing.

Or remove hose connection piece 8 and attach the

exhaust air set (separate) to the connection piece on

the machine. Screw the hose connection piece 8

onto the connection piece. The silencer on the

exhaust air set (separate) can be removed and an air

hose to exhaust equipment mounted instead.

Advantages:

– Noise reduction

– No contamination of the working area by stirred

up dust

– Exhaust air led away.

Working Instructions

DL_bu_3609929393_t.fm5 Seite 11 Donnerstag, 18. Mai 2000 12:29 12

12

3 609 929 393 • 00.05

Before performing any work on the machine

itself, disconnect the air supply.

Keep the machine and the tool holder clean at all times.

If the machine should happen to fail despite the care

taken in manufacture and testing, repair should be

carried out by an authorised customer services agent

for Bosch pneumatic tools.

For all correspondence and spare parts orders, always

include the 10-digit order number of the machine.

Lubrication

Lubricant:

Special gearbox grease 225 ml

3 605 430 009

Molycote grease

SAE 10 / SAE 20 motor oil

Clean regularly the screen on the air inlet of the

machine. For this purpose, unscrew the hose

connection piece 8 and remove dust and dirt

particles from the screen. Then firmly remount the

hose connection piece.

Wash out the gearbox with petroleum after the first

approx. 150 hours of operation and then every 300

hours of operation and lubricate with special gearbox

grease.

Lubricate the moving parts of the clutch after approx.

each 100 000 screwing operations with a few drops of

SAE 10 / SAE 20 motor oil. Grease the sliding and

rolling parts with Molycote grease. Check the clutch

adjustment afterwards.

Any Bosch customer service centre can perform this

work quickly and reliably.

Dispose of lubricants and cleaning agents in an

environmentally correct manner. Observe legal

regulations.

Recycle raw materials instead of disposing as

waste.

Machine, accessories and packaging should be

sorted for environment-friendly recycling.

These instructions are printed on recycled paper

manufactured without chlorine.

We guarantee Bosch products in accordance with

statutory/country-specific regulations (proof of pur-

chase by invoice or delivery note).

Damage attributable to normal wear and tear, over-

load or improper handling will be excluded from the

guarantee.

In case of a claim, please send the machine, com-

pletely assembled, to your dealer or the Bosch

Service Centre for pneumatic tools or power tools.

Great Britain

Robert Bosch Ltd. (B.S.C.)

P.O. Box 98

Broadwater Park

North Orbital Road

Denham-Uxbridge

Middlesex UB 9 5HJ

✆ Service . . . . . . . . . . . . . . . . . . . . . (01895) 838782

Fax . . . . . . . . . . . . . . . . . . . . . . . . . . (01895) 838789

✆ Advice line . . . . . . . . . . . . . . . . . .(01895) 838402

Ireland

Beaver Distribution Ltd.

Greenhills Road

Tallaght-Dublin 24

✆ . . . . . . . . . . . . . . . . . . . . . . . . . . . (01) 4515211

Fax . . . . . . . . . . . . . . . . . . . . . . . . . . . (01) 4517127

USA

Power Tool Service

3718 Polk Avenue

Houston, TX 77003

✆ . . . . . . . . . . . . . . . . . . . . . . . . . . (713) 228-0100

Fax . . . . . . . . . . . . . . . . . . . . . . . . . . (713) 228-0619

We declare under our sole responsibility that this

product is in conformity with the following standards or

standardization documents: EN 792, EN 50 144

according to the provisions of the regulations

89/392/EEC.

Dr. Gerhard Felten Dr. Eckerhard Strötgen

Robert Bosch GmbH, Geschäftsbereich Elektrowerkzeuge

Maintenance and Cleaning

Environmental Protection

Guarantee

Preferential

Partner

Declaration of conformity

Specification subject to alteration without notice

DL_bu_3609929393_t.fm5 Seite 12 Donnerstag, 18. Mai 2000 12:29 12

13

3 609 929 393 • 00.05

Caution! To protect against injury when using pneu-

matic tools, the following general safety measures are

to be observed.

Read and observe these instructions before using the

machine.

1. Always keep the work area orderly.

Disorder in the work area can cause accidents.

2. Take ambient conditions into consideration.

Provide for good lighting. Do not work in areas where the

danger of explosion exists.

3. Keep children out of the working area.

Keep other persons away from your working area.

4. Store the machine and tools safely.

The unused machine and tools should be stored in a dry,

closed room that is not accessible for children.

5. Check the air supply.

Check the air supply regularly. All fittings, connecting

lines and hoses must be constructed to withstand the

pressure and provide the required air volume. Protect the

hose from kinks, restrictions, heat and sharp edges.

Have damaged hoses and couplings repaired

immediately and tighten the hose clamps firmly. Take

care that the hose connection piece is firmly screwed in.

Damage to the air supply can cause a pressure hose to

whip about and lead to injury. Stirred up dust or cutting

chips can cause serious eye injuries.

6. Use the correct tool.

Do not use a machine or tool attachment that is too small

for heavy work. Do not use machines for purposes and

jobs for which they were not intended.

7. Wear suitable clothing.

Do not wear loose clothing or jewellery that could become

caught in moving parts of the machine. Wear a hair net

for long hair. For outside work, non-skidding shoes are

recommended.

8. Wear protective glasses.

For work that produces dust, also wear a dust mask.

9. Secure the Workpiece

Use clamping devices or a vice to hold the workpiece in

place. In this manner, it is held more securely than with

your hand and makes possible the operation of the

machine with both hands.

10. Provide for a secure stance.

Avoid abnormal body positions. Provide for a secure

stance and always keep your balance.

11. Take good care of the machine and tools.

Keep the machine clean and tools sharp for safe and

efficient working. Take care that no dirt enters the

machine by way of the hose connection piece. Observe

the maintenance and the tool change instructions. Keep

the hand grips dry and free from oil and grease.

12. Disconnect the air supply.

Disconnect the air supply when the machine is not in use,

before maintenance work and for the changing of the

insertion tools.

13. Never leave the tool key inserted.

Check before switching on the machine that the tool key

or adjustment tools have been removed.

14. Avoid unintentional switching on.

Never carry a machine that is connected to the air supply

with the finger on the switch. Ensure that the machine is

switched off when connecting to the air supply.

15. Stay constantly alert.

Observe the work continuously. Proceed in a sensible

manner. Do not use the machine when your concen-

tration is poor.

16. Check the machine for damage.

Before using the machine, carefully check the protective

devices and the easily damaged parts for flawless

functioning as intended. Check if the function of moving

parts is in order, that they are not jammed or if parts are

damaged. All parts must be properly mounted and all

conditions fulfilled to ensure the flawless operation of the

machine.

Damaged protective devices and parts should be

repaired or replaced in a professional manner by an

authorised customer service facility if nothing to the

contrary is noted in the operating instructions. Damaged

switches must be replaced by a customer service facility.

Do not use a machine that cannot be switched on and off

with the switch.

17. Caution!

For your own safety, use only accessories and attach-

ments that are referred to in the operating instructions.

The use of tool inserts or accessories other than those

recommended in the operating instructions or in the

catalogue can result in the danger of personal injury.

18. Have repairs performed only by a specialist.

This pneumatic tool complies with the relevant safety

regulations. Repairs should be performed only by a

specialist, otherwise, accidents to the operator can

occur.

Save these safety instruction in an accessible place.

Safety Instructions for Pneumatic Tools

DL_bu_3609929393_t.fm5 Seite 13 Donnerstag, 18. Mai 2000 12:29 12

Page is loading ...

Bosch DL 0 607 460 001 Product information

This manual is also suitable for

Bosch DL 0 607 460 001 Product information

in other languages

Related papers

Other documents