Gardena R45Li Installation guide

R38Li, R40Li, R45Li,

R50Li, R70Li, R80Li

INSTALLATION MANUAL

GARDENA ROBOTIC LAWNMOWER

INSTALLATION MANUAL

GARDENA ROBOTIC LAWNMOWER

OMSLAG QG, BRUX, 1155943-.indd 2 2014-10-17 10.29

TABLE OF CONTENTS

English - 3

Introduction and safety ................................................... 5

Introduction ........................................................................ 5

Symbols on the product ..................................................... 6

Symbols in the Operator’s Manual ................................... 7

Safety Instructions ............................................................ 8

Presentation ................................................................... 11

What is what? ................................................................. 12

Package Contents ........................................................... 13

Function ........................................................................... 14

Search method ................................................................ 16

Installation ...................................................................... 17

Preparations .................................................................... 17

Installation of the charging station .................................. 18

Charging the battery ........................................................ 22

Installation of the boundary wire ...................................... 23

Connecting the boundary wire ........................................ 29

Installation of the guide wire ........................................... 30

Checking the loop ........................................................... 34

First start-up and calibration ............................................ 34

Test docking with the charging station ............................ 35

Use ................................................................................. 36

Charging a flat battery .................................................... 36

Using the timer ............................................................... 37

Starting ............................................................................ 38

Stopping .......................................................................... 38

Switching off .................................................................... 39

Adjusting the cutting height ............................................ 39

Control panel ................................................................ 40

Operation selection ........................................................ 41

Multi-choice buttons ........................................................ 42

Numbers ......................................................................... 42

Main switch ..................................................................... 42

Menu functions ............................................................. 43

Main menu ...................................................................... 43

Menu structure ................................................................. 44

Timer ............................................................................... 46

Installation, R70Li, R80Li ................................................ 49

Security ............................................................................ 53

Settings ........................................................................... 55

Garden examples .......................................................... 59

Maintenance .................................................................. 63

Winter storage ................................................................ 64

After winter storage ......................................................... 64

Cleaning ......................................................................... 65

Transport and removal .................................................... 66

In the event of a thunderstorm ........................................ 66

Replacing the blades ...................................................... 67

Replacing the battery ...................................................... 67

Troubleshooting ........................................................... 69

Messages ....................................................................... 69

Indicator lamp in the charging station .............................. 72

Symptoms ....................................................................... 73

Finding breaks in the loop wire ........................................ 75

Technical Data .............................................................. 79

Guarantee terms ............................................................ 81

Environmental information ........................................... 82

EU Declaration of Conformity ...................................... 83

1157069-26,R40Li_GB.book Page 3 Wednesday, November 19, 2014 5:02 PM

MEMO

4 - English

The Product Registration Key is a valuable document and must be stored in a safe place. This key is

necessary for example to register the product on GARDENA's website or to unlock the robotic lawnmower

in the event of a lost PIN code. The product registration key is provided in a separate document in the

product packaging.

If the robotic lawnmower is stolen, it is important to notify GARDENA of this. Contact GARDENA Central

Service and provide the robotic lawnmower's serial number and product registration key so that it can be

registered as stolen in an international database. This is an important step in the robotic lawnmower's theft

protection which reduces interest in the buying and selling of stolen mowers.

Always have the robotic lawnmower's serial number at hand when you contact GARDENA Central

Service, as this will provide you with faster support.

GARDENA Central Service

www.gardena.com

Serial number:

PIN code:

Product registration key:

1157069-26,R40Li_GB.book Page 4 Wednesday, November 19, 2014 5:02 PM

English - 5

1. INTRODUCTION AND SAFETY

1. Introduction and safety

1.1 Introduction

Congratulations on your choice of an exceptionally

high quality product. To get the best results from your

GARDENA robotic lawnmower requires knowledge of

how it works. This Operator's Manual contains

important information about the robotic lawnmower,

how it must be installed and how to use it.

As a complement to this Operator's Manual, there is

more information available on GARDENA's website,

www.gardena.com. Here you can find more help and

guidance in the use of the robotic lawnmower.

The following system is used in the Operator's

Manual to make it easier to use:

• Text written in italics is a text that is shown on the

robotic lawnmower's display or is a reference to

another section in the Operator's Manual.

• Words written in

bold

are one of the buttons on

the robotic lawnmower's keypad.

• Words written in

UPPERCASE

and

italics

refer to

the position of the main switch and the different

operating modes available in the robotic

lawnmower.

GARDENA has a policy of continuous product

development and therefore reserves the right to modify

the design and appearance and function of products

without prior notice.

IMPORTANT INFORMATION

Please read the Operator’s Manual carefully

and make sure you understand the

instructions before using your robotic

lawnmower.

WARNING

The robotic lawnmower can be

dangerous if incorrectly used.

WARNING

Never use the robotic lawnmower

when persons, especially children, or

pets, are in the cutting area.

www.gardena.com

1157069-26,R40Li_GB.book Page 5 Wednesday, November 19, 2014 5:02 PM

6 - English

1. INTRODUCTION AND SAFETY

1.2 Symbols on the product

These symbols can be found on the robotic

lawnmower. Study them carefully.

• Please read the Operator’s Manual carefully and

make sure you understand the instructions

before using your robotic lawnmower. The

warnings and safety instructions in this

Operator’s Manual must be carefully followed if

the mower is to be used safely and efficiently.

• The robotic lawnmower can only start when the

main switch is set to 1 and the correct PIN code

has been entered. Turn the main switch to 0

before carrying out any inspections and/or

maintenance.

• Remain at a safe distance from the robotic

lawnmower when it is running. Keep your hands

and feet away from the rotating blades. Never

put your hands or feet close to or under the body

when the robotic lawnmower is running.

• Do not ride on the robotic lawnmower.

• This product conforms to the applicable

EC Directives.

• Noise emission to surroundings. The product's

emissions are set out in chapter 10, Technical

data and on the rating plate.

• It is not permitted to dispose of this product as

normal household waste when it has reached the

end of its useful life. Ensure that the product is

recycled in accordance with local legal

requirements.

• Never use a high-pressure washer or even

running water to clean the robotic lawnmower.

1157069-26,R40Li_GB.book Page 6 Wednesday, November 19, 2014 5:02 PM

English - 7

1. INTRODUCTION AND SAFETY

• The low voltage cable must not be shortened,

extended or spliced.

• Do not use a trimmer nearby the low voltage

cable. Be careful when trimming edges where

the cables are placed.

1.3 Symbols in the Operator’s

Manual

These symbols can be found in the Operator’s Manual.

Study them carefully.

• Turn the main switch to 0 before carrying out any

inspections and/or maintenance.

• Always wear protective gloves when working

with the mower’s chassis.

• Never use a high-pressure washer or even

running water to clean the robotic lawnmower.

• A warning box indicates the risk of personal

injury, especially if the instructions are not

followed.

• An information box indicates the risk of material

damage, especially if the instructions are not

followed. The box is also used where there is a

risk of user error.

3012-1351

WARNING

Text

IMPORTANT INFORMATION

Text

1157069-26,R40Li_GB.book Page 7 Wednesday, November 19, 2014 5:02 PM

8 - English

1. INTRODUCTION AND SAFETY

1.4 Safety Instructions

Use

• This robotic lawnmower is designed to mow

grass in open and level ground areas. It may

only be used with the equipment recommended

by the manufacturer. All other types of use are

incorrect. The manufacturer’s instructions with

regard to operation, maintenance and repair

must be followed precisely.

• Never use the robotic lawnmower when persons,

especially children, or pets, are in the cutting area.

If there are persons, or pets, in the cutting area it

is recommended that the lawnmower be

programmed for use during hours when the area

is free from persons, e.g. at night. See 6.3 Timer.

• The robotic lawnmower may only be operated,

maintained, and repaired by persons that are fully

conversant with its special characteristics and

safety regulations. Please read the Operator’s

Manual carefully and make sure you understand

the instructions before using the robotic

lawnmower.

• It is not permitted to modify the original design of

the robotic lawnmower. All modifications are made

at your own risk.

• Check that there are no stones, branches, tools,

toys or other objects on the lawn that can damage

the blades and cause the mower to stop.

• Start the robotic lawnmower according to the

instructions. When the main switch is in

position 1, make sure you keep your hands and

feet away from the rotating blades. Never put your

hands and feet under the robotic lawnmower.

• Never lift up the robotic lawnmower or carry it

around when the main switch is in position 1.

• Do not let persons who do not know how the

robotic lawnmower works and behaves use the

robotic lawnmower.

• The robotic lawnmower must never be allowed to

collide with persons or other living creatures. If a

person or other living creature comes in the

lawnmower’s way it shall be stopped

immediately. See 4.4 Stopping.

• Do not put anything on top of the robotic

lawnmower or its charging station.

• Do not allow the robotic lawnmower to be used with

a defective blade disc or body. Neither should it be

used with defective blades, screws, nuts or wires.

• Do not use the robotic lawnmower if the main

switch does not work.

• Always switch off the robotic lawnmower using the

main switch when the robotic lawnmower is not in

1157069-26,R40Li_GB.book Page 8 Wednesday, November 19, 2014 5:02 PM

English - 9

1. INTRODUCTION AND SAFETY

use. The robotic lawnmower can only start when

the main switch is set to 1 and the correct PIN

code has been entered.

• The robotic lawnmower must never be used at the

same time as a sprinkler. In this case use the

timer function (see 6.3 Timer on page 46) so the

mower and sprinkler never run simultaneously.

• The built-in alarm is very loud. Be careful,

especially if the robotic lawnmower is handled

indoors.

• Full compatibility cannot be guaranteed between

the robotic lawnmower and other types of wireless

systems such as remote controls, radio

transmitters, hearing loops, buried electric animal

fencing or similar.

• Metal objects in the ground (e.g. reinforced

concrete or anti-mole nets) can result in a

stoppage. The metal objects can cause

interference with the loop signal which then can

lead to a stoppage.

1157069-26,R40Li_GB.book Page 9 Wednesday, November 19, 2014 5:02 PM

10 - English

1. INTRODUCTION AND SAFETY

Transport

The original packaging should be used when

transporting the robotic lawnmower over long

distances.

To safely move from or within the working area:

1. Press the STOP button to stop the robotic

lawnmower. If security is set to the medium or

high level (see 6.5 Security on page 53), the PIN

code has to be entered. The PIN code contains

four digits and is selected when you start the

robotic lawnmower for the first time. See 3.8 First

start-up and calibration on page 34.

2. Set the main switch in position 0.

3. Carry the robotic lawnmower by the handle at the

rear under the robotic lawnmower. Carry the

robotic lawnmower with the blade disc away from

the body.

Maintenance

• Inspect the robotic lawnmower each week and

replace any damaged or worn parts.

• Check especially that the blades and blade disc

are not damaged. Check also that the blades can

pivot freely. Replace all blades and screws at the

same time if necessary so that the rotating parts

are kept balanced. See 8.6 Replacing the blades

on page 67.

IMPORTANT INFORMATION

Do not lift the robotic lawnmower when it is

parked in the charging station. This may

damage the charging station and/or the

robotic lawnmower. Open the cover and

instead first pull the robotic lawnmower out

of the charging station before lifting it.

IMPORTANT INFORMATION

Never use a high-pressure washer or even

running water to clean the robotic

lawnmower. Never use solvents for cleaning.

1157069-26,R40Li_GB.book Page 10 Wednesday, November 19, 2014 5:02 PM

English - 11

2. PRESENTATION

2. Presentation

This chapter contains information that is important to

be aware of when planning the installation.

Installation of the robotic lawnmower involves four

main components:

• A robotic lawnmower that mows the lawn by

essentially operating in a random pattern. The

robotic lawnmower is powered by a

maintenance-free battery.

• A charging station, to where the robotic

lawnmower returns when the charge level in the

battery becomes too low.

The charging station has three functions:

• To send control signals along the boundary

wire.

• To send control signals in the guide wire so

that the robotic lawnmower can find the

charging station.

• To charge the robotic lawnmower battery.

• A transformer, which is connected between the

charging station and a 100-240V wall socket.

The transformer is connected to the wall socket

and to the charging station using a 10 m long low

voltage cable. The low voltage cable must not be

shortened or extended. A 20 meter low voltage

cable is available to purchase as an accessory.

Contact GARDENA Central Service for more

information.

• Loop wire, laid in a loop around the robotic

lawnmower’s working area. The loop wire is laid

around the edges of the lawn and around objects

and plants that the robotic lawnmower must not

run into. The loop wire is used both as a

boundary wire and a guide wire.

The loop wire supplied for the installation is 200

m long (150 m for the GARDENA R38Li, R40Li,

R45Li & R50Li). If it is not long enough, more

loop wire can be purchased and spliced onto the

existing loop wire with an original coupler.

The maximum permitted length for the loop wire

is 400 m.

1157069-26,R40Li_GB.book Page 11 Wednesday, November 19, 2014 5:02 PM

12 - English

2. PRESENTATION

2.1 What is what?

The numbers in the illustration represent:

1. Body

2. Cover to display, keypad and cutting height

adjustment

3. Stop button/Catch to open the cover

4. Contact strips

5. LED for operation check of the charging station,

boundary wire and guide wire

6. Charging station

7. Carry handle

8. Battery cover

9. Blade disc

10. Chassis box with electronics, battery and motors

11. Main switch

12. Rear wheel

13. Charging strip

14. Keypad

15.

Display

16. Loop wire for boundary loop and guide wire

17. Low voltage cable

18. Connector for connecting the loop wire to the

charging station

19. Screws for securing the charging station

20. Transformer (the appearance of the transformer

may differ depending on market)

21. Staples

22. Measurement gauge for help when installing the

boundary wire (the measurement gauge is broken

loose from the box)

23. Coupler for the loop wire

24. DVD installation video

25. Operator's Manual and Quick Guide

26. Extra blades

27. Alarm decal

28. Rating plate

1

3

2

16

17

6

5

4

12

13

11

19

20

21

22 23

25

24

18

8

9

10

7

26

27

14

28

15

3018-169

1157069-26,R40Li_GB.book Page 12 Wednesday, November 19, 2014 5:02 PM

English - 13

2. PRESENTATION

2.2 Package Contents

Your Gardena

®

robotic mower package contains the following details.

Gardena® R38Li, R40Li,

R45Li, R50Li

Gardena® R70Li, R80Li

Robotic mower √ √

Charging station √ √

Transformer √ √

Loop wire 150 m 200 m

Low voltage cable √ √

Pegs 200 pcs 400 pcs

Connectors 5 pcs 5 pcs

Charging station screws 3 pcs 3 pcs

Allen key √ √

Measurement gauge √ √

Couplers 7 pcs 7 pcs

CD √ √

Operator's Manual and Quick Guide √ √

Extra blades 3 pcs 3 pcs

Alarm decal 2 pcs 2 pcs

1157069-26,R40Li_GB.book Page 13 Wednesday, November 19, 2014 5:02 PM

14 - English

2. PRESENTATION

2.3 Function

Capacity

The robotic lawnmower is recommended for lawn sizes

up to the maximum capacity listed in the technical data

section.

How big an area the robotic lawnmower can keep cut

depends primarily on the condition of the blades and

the type, growth and moisture of the grass. The shape

of the garden is also significant. If the garden mainly

consists of open lawns, the robotic lawnmower can

mow more in one hour than if the garden consists of

several small lawns separated by many trees, flower

beds and passages.

A fully charged robotic lawnmower mows for 40 to

60 minutes, depending on the age of the battery and

how thick the grass is. Then the robotic lawnmower will

charge for 60 to 90 minutes. The charging time can

vary depending on, among other factors, the ambient

temperature.

Mowing technique

The robotic lawnmower's mowing system is based on

an efficient and energy saving principle. Unlike many

standard lawnmowers, the robotic lawnmower cuts

the grass instead of knocking it off.

It is recommended to allow the robotic lawnmower to

mainly mow in dry weather to obtain the best possible

result. The robotic lawnmower can also mow in the

rain, however, wet grass easily sticks on the robotic

lawnmower and there is a greater risk of slipping on

steep slopes.

If there is risk for thunder, the transformer should be

disconnected from the power and the boundary wire

and the guide wire from the charging station.

The blades must be in good condition to obtain the

best mowing result. In order to keep the blades sharp

for as long as possible it is important to keep the lawn

free from branches, small stones and other objects.

Replace the blades regularly for the best mowing

result. It is very easy to replace the blades. See

8.6 Replacing the blades on page 67.

1157069-26,R40Li_GB.book Page 14 Wednesday, November 19, 2014 5:02 PM

English - 15

2. PRESENTATION

Working method

The robotic lawnmower automatically mows the lawn.

It continuously alternates between mowing and

charging.

The robotic lawnmower starts to search for the

charging station when the battery charge becomes

too low. The robotic lawnmower does not mow when

it is searching for the charging station.

When the robotic lawnmower searches for the

charging station, it first searches irregularly for the

guide wire. Then it follows the guide wire to the

charging station, turns around just in front of the

station and backs into it.

When the battery is fully charged, the robotic

lawnmower leaves the charging station in a randomly

selected direction within the 90˚-270˚ exit sector.

To ensure an even cut, even in inaccessible parts of

the garden, the robotic lawnmower can follow the

guide wire out from the charging station to where the

guide wire connects to the boundary wire to begin

mowing there.

When the robotic lawnmower body hits an obstacle,

the robotic lawnmower reverses and selects a new

direction.

Two sensors, one on the front and one on the back of

the robotic lawnmower, will sense when the robotic

lawnmower is approaching the boundary wire. The

robotic lawnmower overruns the wire by up to

28 centimetres before it turns back.

The STOP button on the top of the robotic

lawnmower is mainly used to stop the robotic

lawnmower when it’s running. When the STOP button

is pressed a cover opens, behind which there is a

control panel. The

STOP

button remains pressed in

until the cover is closed again. This acts as a start

inhibitor.

1157069-26,R40Li_GB.book Page 15 Wednesday, November 19, 2014 5:02 PM

16 - English

2. PRESENTATION

The control panel on the top of the robotic

lawnmower is where you manage all the robotic

lawnmower settings. Open the control panel cover by

pressing down the STOP button.

When the main switch is set to position 1 for the first

time, a start-up sequence begins which includes

language selection, time format, date format and the

four-digit PIN code and setting the time and date. See

3.8 First start-up and calibration on page 34.

Movement pattern

The robotic lawnmower’s movement pattern is

irregular and is determined by the robotic lawnmower

itself. A movement pattern is never repeated. With

the mowing system the lawn is mown equally without

any mowing lines from the robotic lawnmower.

2.4 Search method

The robotic lawnmower runs irregularly until it reaches

the guide wire. Then the robotic lawnmower follows the

guide wire to the charging station.

The guide wire is a wire that is laid from the charging

station towards, for instance, a remote part of the

working area or through a narrow passage to be then

connected with the boundary wire. For more

information, see 3.6 Installation of the guide wire

on page 34.

Start

1

1 23 4 5

4

78

0

9

56

23

1157069-26,R40Li_GB.book Page 16 Wednesday, November 19, 2014 5:02 PM

English - 17

3. INSTALLATION

3. Installation

This chapter describes how you install the GARDENA

robotic lawnmower. Before starting the installation

read the previous chapter 2. Presentation.

Read also through this entire chapter before beginning

the installation. How the installation is done also

affects how well the robotic lawnmower works. It is

therefore important to plan the installation carefully.

Planning is simplified if you make a sketch of the

working area, including all obstacles. This makes it

easier to see the ideal positions for the charging

station, the boundary wire and the guide wire. Draw on

the sketch where the boundary and guide wires should

be routed.

See 7. Garden examples on page 59 for installation

examples.

Visit also www.gardena.com for further descriptions

and tips regarding installation.

Carry out the installation in the following steps:

3.1 Preparations.

3.2 Installation of the charging station.

3.3 Charging the battery.

3.4 Installation of the boundary wire.

3.5 Connecting the boundary wire.

3.6 Installation of the guide wire

3.7 Checking the loop.

3.8 First start-up and calibration

3.9 Test docking with the charging station

The charging station and boundary and guide wires

must be connected to be able to carry out a complete

start-up of the robotic lawnmower.

3.1 Preparations

1. If the lawn in the working area is longer than

10 cm, mow it using a standard lawnmower.

Then collect the grass.

2. Read carefully through all the steps before the

installation.

3. Check that all parts for the installation are

included. The numbers in brackets refer to the

component illustration 2.1 What is what?.

• Robotic lawnmower

• Charging station (6)

• Loop wire for boundary wire and guide

wire (16)

• Transformer (20)

1157069-26,R40Li_GB.book Page 17 Wednesday, November 19, 2014 5:02 PM

18 - English

3. INSTALLATION

• Low voltage cable (17)

• Staples (21)

• Connector for connecting the loop wire to the

charging station(18)

• Screws for the charging station (19)

• Measurement gauge (22)

• Couplers for the loop wire (23)

During installation you will also need:

• Hammer/plastic mallet (to simplify putting the

staples in the ground)

• Combination pliers for cutting the boundary

wire and pressing the connectors together.

• Polygrip (for pressing the couplers together).

• Edge cutter/straight spade if the boundary wire

must be buried.

3.2 Installation of the charging

station

Ideal position for the charging station

Take the following aspects into consideration when

identifying the best location for the charging station:

• Allow for 3 metres of free space in front of the

charging station

• It must be possible to lay at least 1.5 metres of

boundary wire straight out to the right and left

of the charging station

• It must be close to a wall socket The supplied

low voltage cable is 10 metres long. A 20

meter low voltage cable is available to

purchase as an accessory. Contact GARDENA

Central Service for more information.

• A level surface to place the charging station on

• Protection from water spray for instance from

irrigation

• Protection from direct sunlight

• Place in the lower part of a working area that

has a major slope

• Possible requirement to keep the charging

station out of sight for outsiders

For an example of an ideal position of the charging

station, see 7. Garden examples on page 59.

1157069-26,R40Li_GB.book Page 18 Wednesday, November 19, 2014 5:02 PM

English - 19

3. INSTALLATION

The charging station must be positioned with a great

deal of free space in front of it (at least 3 metres). It

should also be centrally placed in the working area to

make it easier for the robotic lawnmower to reach all

areas in the working area.

Do not put the charging station in confined spaces in

the working area. There must be a straight boundary

wire, at least 1.5 metres long, to the right and left of

the charging station. The wire must be laid straight

out from the rear end of the charging station. Any

other locations can mean that the robotic lawnmower

enters the charging station sideways and will have

difficulty docking.

Do not put the charging station in a corner in the

working area. There must be a straight boundary

wire, at least 1.5 metres long, to the right and left of

the charging station.

The charging station must be positioned on relatively

level ground. The front end of the charging station

must be a maximum of 3 cm higher than the back

end. The front end of the charging station must never

be lower than the back end.

The charging station must not be positioned in a way

that can bend its base plate.

3020-043

3

1157069-26,R40Li_GB.book Page 19 Wednesday, November 19, 2014 5:02 PM

20 - English

3. INSTALLATION

If the installation is done in a working area with a

steep slope (such as around a house on a hill), the

charging station should be placed in the area at the

bottom of the slope. This makes it easier for the

robotic lawnmower to follow the guide wire to the

charging station.

The charging station should not be placed on an

island as this limits the laying of the guide wire in an

optimal way. If the charging station has to be installed

on an island, the guide wire also has to be connected

to the island. See the illustration opposite. Read more

about islands in chapter 3.4 Installation of the

boundary wire

on page 23.

Connecting the transformer

Take the following into consideration when planning

where to place the transformer:

• Close to the charging station

• Protection from rain

• Protection from direct sunlight

If the transformer is connected to an electrical socket

outdoors, this must be approved for outdoor use.

The low voltage cable for the transformer is 10

metres long, and may not be shortened or extended.

1157069-26,R40Li_GB.book Page 20 Wednesday, November 19, 2014 5:02 PM

Page is loading ...

Gardena R45Li Installation guide

This manual is also suitable for

Gardena R45Li Installation guide

Related papers

Other documents