Brookstone Pack Speaker User manual

Brand: Brookstone

Model: Pack Speaker

Category: Docking speakers

Type: User manual

• Increase the distance between the

equipment and receiver.

• Connect the equipment to an outlet

on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an

experienced radio/TV technician

for help.

1. Micro USB Charging Port

2. Dust Cover

3. Aux-In Port

4. Power/Pairing Button

5. Volume Down Button

6. Play/Pause/Call Button

7. Volume Up Button

8. Micro USB Charging Cable

(not shown)

4 5 6 7

1 32

Fold Fold Fold Fold Fold

CHARGING THE PACK

SPEAKER

1. Turn off Pack Speaker before

charging.

2. Connect the speaker to a PC/

Laptop or a 5V USB adapter (not

included) with the included USB

charging cable.

3. The Battery Indicator will turn on

red during charging and will turn

off when fully charged. It takes

about 2 hours to fully charge.

NOTE: The red LED will keep flashing

fast and the indication tone will repeat

every 30 seconds when battery is low.

TURNING ON/OFF THE

SPEAKER

1. Press and hold the Power Button

for 3 seconds to turn on the

speaker. The Battery and

Bluetooth

indicators turn on at the

same time.

2. Press and hold the Power Button

for 3 seconds to turn the speaker

off.

PAIRING YOUR DEVICE

1. Please keep the Pack Speaker and

the mobile device within 1 meter

of each other.

2. Turn on the Speaker. When the red

LED blinks quickly, the speaker is in

standby for pairing.

LOCATION OF PARTS AND

CONTROLS

This equipment complies with Part 15

ot the FCC Rules. Operation is subject

to the following two conditions:

1. This equipment may not cause

harmful interference.

2. This equipment must accept any

interference received, including

interference that may cause

undesired operation.

Modifications not authorized by the

manufacturer may void the user’s

authority to operate this device.

FCC ID: 2ABPRV9

Merrimack, New Hampshire, USA 03054

800-846-3000 • Brookstone.com

310850/310851/310848/310849

SPECIFICATIONS

Power Output: 3W

DC Input: 5V 500mA

Range: Class 2, up to 33 ft (10m)

Battery Capacity: 3.7V 800mAh

Charging Time: Approx. 2 hours

Battery Life: Approx. 5 hours

Compatibility: Bluetooth 2.0 or above

device with A2DP/AVRCP/HFP/HSP

Fold Fold Fold Fold Fold

The Bluetooth

word mark and logos

are registered trademarks owned of

Bluetooth SIG, Inc. and any use

of such marks by Brookstone is under

license.

Store the speaker in a cool, dry place.

1. When you have an incoming call,

the speaker sounds an incoming

call tone. Both the speaker and your

cellphone may ring, depending on

your cellphone settings.

2. To answer an incoming call, short

press Play/Pause Button to answer

the call.

3. To reject an incoming call, long

press Play/Pause Button to reject

the call.

4. To end a call, short press

Play/Pause Button once.

5. If, while you are listening to music,

your phone rings and you answer

the call, the music selection will

then continue from where it had

stopped after you end the call.

NOTES:

LISTENING TO YOUR AUDIO

DEVICE

1. Play your audio device as you

normally would.

2. Volume may be adjusted on your

audio device or by pressing and

holding the Volume Up or Down

buttons on the speaker.

3. A single press of the Volume Up

or Down buttons will advance to

the next track or go back to the

previous track.

4. To pause audio, press the Play/Pause

Button on the Speaker. To resume

audio playback, press the Play/Pause

Button again.

PLAYING MUSIC THROUGH A

WIRED CONNECTION

You can connect your audio device to

the speaker with a 3.5mm audio cable

(not included).

1. Plug one end of the cable into your

audio device, just like you would a

pair of headphones.

2. Plug the other end of the cable into

the speaker's AUX-IN port.

3. Use your audio device to control

music playback and volume

through speaker.

WATER-RESISTANT

1. Pack Speaker is compliant with

IPX4 waterproof standard “splash

proof in all directions.”

2. Never place the speaker under

running water or submerge

the speaker in water.

3. Once the speaker is in pairing mode

and your device is ready to pair,

select ‘Pack Speaker.’ If prompted,

use 0000 as a PIN for the pairing

code. Once the speaker is selected,

LED indicator will change to solid

blue to complete pairing.

1. If pairing is not successful, turn

the speaker off and on again.

2. After successful pairing, paired

devices will remember each other.

3. The AUX-IN will take priority over

Bluetooth

. Bluetooth

connection

is disconnected when AUX-IN is

plugged in. Bluetooth

will be

reconnected when AUX-IN is

unplugged.

CARE AND STORAGE

MOBILE PHONE OPERATION

Brookstone Pack Speaker User manual

Brand: Brookstone

Model: Pack Speaker

Category: Docking speakers

Type: User manual

Download PDF

report

Brookstone Pack Speaker User manual

Brookstone Pack Speaker User manual

Related papers

Other documents