Whirlpool AKM 404/NB/01 Program Chart

Brand: Whirlpool

Model: AKM 404/NB/01

Category: Hobs

Type: Program Chart

Whirlpool AKM 404/NB/01 gas hob offers a safe and efficient cooking experience. Equipped with advanced safety features, it prevents gas leaks and unintended ignition. The hob's high-quality burners provide precise flame control for a variety of cooking needs, from simmering delicate sauces to searing meats. Its durable design and easy-to-clean surface make it a practical choice for any kitchen.

YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY IMPORTANT

This manual and the appliance itself provide important safety messages, to be read and observed at all times.

All Safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what

can happen if the instructions are not followed.

- The appliance must be disconnected from the power supply before carrying out any installation work.

- Installation and maintenance must be carried out by a qualified technician, in compliance with the manufacturer’s

instructions and local safety regulations. Do not repair or replace any part of the appliance unless specifically stated in

the user manual.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this appliance.

The electrical and gas connections must comply with local regulations.

- The appliance must be disconnected from the power supply before carrying out any

installation work.

- Installation and maintenance must be carried out by a qualified technician, in compliance

with the manufacturer’s instructions and local safety regulations. Do not repair or replace any

part of the appliance unless specifically stated in the user manual.

- Regulations require that the appliance is earthed.

- The appliance (class 3) is designed solely for private household use for cooking food. Do not

use this appliance as a space heater to heat or warm the room. Doing so may result in carbon

monoxide poisoning and overheating of the hob. The Manufacturer declines all

responsibility for inappropriate use or incorrect setting of the controls.

- The appliance and its accessible parts may become very hot during use. During and after use,

do not touch the heating elements of the appliance.

- Keep children less than 8 years of age away from the appliance and supervise them to ensure

they do not play with it.

- This appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if they

have been given supervision or instruction concerning use of the appliance in a safe way and

understand hazards involved. Cleaning and user maintenance shall not be made by children

without supervision.

- Overheated oils and fats catch fire easily. Never leave the appliance unattended when

cooking with fat and oil.

In case of hotplate glass breakage:

Shut immediately off all burners and any electrical heating element and isolate the

appliance from the power supply.

Do not touch the appliance surface.

Do not use the appliance.

- The appliance is not intended to be operated by means of an external timer or separate

remote control system.

- Do not use steam cleaners.

- Unattended cooking on a hot with fat or oil can be dangerous and may result in fire. NEVER

try to extinguish a fire with water, but switch off the appliance and then cover flame, e.g. with

a lid or a fire blanket.

- Danger of fire: do not store items on the cooking surfaces.

- The power cable must be long enough for connecting the appliance, once fitted in its housing, to the power supply

- Use only flexible or rigid metal hose for gas connection.

- If necessary, the electrical power cable must be replaced exclusively with a power cable having identical characteristics

to the original supplied by manufacturer (type H05V2V2-F 90°C or H05RR-F). This operation must be performed by a

qualified electrician.

- The manufacturer cannot be held responsible for any injury to persons or animals or damage to property arising from

failure to comply with these requirements.

- Do not use multiple plug adapters or extension cords.

- Do not pull the power supply cord in order to unplug the appliance.

- The electrical components must not be accessible to the user after installation.

- Do not touch the appliance with any wet part of the body and do not operate it when barefoot.

- The use of a gas appliance produces heat and humidity in the room. Make sure the room is well-ventilated, or install an

extractor hood with exhaust duct.

- In case of prolonged use, additional ventilation may be necessary (by opening a window or increasing the hood

extraction speed).

- After use, make sure the knobs are in off position and close the main gas supply cock or the gas cylinder valve.

- Keep the packaging materials out of the reach of children.

- Before cleaning or maintenance wait for hob to cool down.

- These instructions are valid for those Countries whose symbol is shown on the rating plate (under cooktop).

- This product is not intended to be installed and operated outdoor.

After unpacking the hob, make sure that it has not been damaged during transport. In the event of problems, contact the

dealer or your nearest After-sales Service.

TECHNICAL INFORMATION FOR THE INSTALLER

• This product can be embedded in a worktop 20 to 60 mm thick.

• If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the

work surface. This panel must be positioned at a maximum distance of 150 mm below the upper surface of the

work surface but, in no case less than 20 mm from the bottom of the hob. In the case that you intend to install an

oven beneath the hob, make sure that it is equipped with a cooling system. The manufacturer declines all liability

if another brand oven is installed beneath the hob.

• Before installation, make sure that:

- the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the

rating plate and injector table);

- the outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations;

- this appliance is not connected to a fume exhaust device. It shall be installed in accordance with current installation

regulations. Particular attention shall be given to the relevant requirements regarding ventilation;

- combustion products are discharged outdoors through specific hoods or wall and/or window mounted electrical fans.

IMPORTANT SAFETY INSTRUCTIONS

This is the safety alert symbol, pertaining to safety, which alerts users to potential hazards to themselves and others.

All safety messages will follow the safety alert symbol and either the terms:

DANGER

Indicates a hazardous situation which, if not avoided, will cause serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could cause serious injury.

WARNING

If the information in this manual is not followed exactly, a fire or explosion may result

causing property damage or injury.

What to do if you smell gas:

- Do not try to light any appliance.

- Do not touch any electrical switch.

- Do not use any phone in your building.

- Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

- Use appliance in well ventilated rooms only.

SAVE THESE INSTRUCTIONS

INSTALLATION

EN BUILT-IN GAS HOB

5019 300 02648 Manufacturer: Whirlpool Europe S.r.l. Viale G. Borghi, 27 21025 Comerio (VA) ITALY

GAS CONNECTION

ELECTRICAL CONNECTION

IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate.

ADJUSTMENT TO DIFFERENT TYPES OF GAS

If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label

on the top of the hob, change the injectors.

Remove the information label and keep it with the instructions booklet.

Use pressure regulators suitable for the gas pressure indicated in the Instruction.

• The gas nozzles must be changed by After Sales Service or a qualified technician.

• Nozzles not supplied with the appliance must be ordered from After Sales Service.

• Adjust the minimum setting of the taps.

NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will go.

IMPORTANT: should you experience difficulty in turning the burners knobs, please contact the After Sales Service for

the replacement of the burner tap if found to be faulty.

REPLACING THE INJECTORS (see the injector table in the Instruction)

ADJUSTING MINIMUM GAS SETTING OF TAPS

WARNING

This operation must be performed by a qualified technician.

• The gas supply system must comply with local regulations.

• You can find specific local regulations for some countries in the paragraph

“Reference to Local Regulations”. If no information concerning your Country is

given, please ask details to your Installer.

• The connection of the hob to the gas pipe network or gas cylinder must be made by

means of a rigid copper or steel pipe with fittings complying with local regulations, or

by means of a continuous-surface stainless steel hose complying with local

regulations. The maximum length of the hose is 2 linear metres.

• Connect elbow (A)* or (B)* supplied with to the hob inlet main pipe and interpose

the washer (C) supplied, in compliance with EN 549.

*Use elbow (A) for France and elbow (B) for all other destinations.

IMPORTANT: if a stainless steel hose is used, it must be installed so as not to touch

any mobile part of the furniture. It must pass through an area where there are no

obstructions and where it is possible to inspect it on all its length.

• After connection to the gas supply, check for leaks with soapy water. Light up the

burners and turn the knobs from max position to minimum position to check

flame stability.

WARNING

This operation must be performed by a qualified technician.

WARNING

• The electrical connections must comply

with local regulations.

• The earthing of this appliance is

compulsory by law.

• Do not use an extension cord.

ASSEMBLY

After having cleaned the perimeter surface,

apply the supplied gasket to the hob as shown

in the figure.

Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction.

NOTE: the power supply cable must be long enough to permit its upward extraction.

To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and

fasten them by means of their screws in accordance with the thickness of the worktop (see the following figures).

Earth

(yellow/green)

Top 20 mm Top 40 mm

Top 30 mm Top 60 mm

WARNING

This operation must be performed by a qualified technician.

• Remove grids (A).

•Extract burners (B).

• Using a socket spanner of the appropriate size unscrew

the injector (C), unscrew the injector to be replaced.

• Replace it with the injector suitable for the new type of

gas.

• Re-assemble the injector in (D).

• If you have a multiple crown burner use side spanner to

replace the injector (E).

Before installing the hob, remember to affix the gas

calibration plate supplied with the injectors in such a way

that it covers the existing information relating to gas

calibration.

To ensure that the minimum setting is correctly adjusted, remove the knob and

proceed as follows:

• tighten screw to reduce the flame height (-);

• loosen screw to increase the flame height (+).

The adjustment must be performed with the tap in minimum gas setting position (small

flame) .

• The primary air of the burners does not need to be adjusted.

• At this stage, light up the burners and turn the knobs from max position to

minimum position to check flame stability.

Upon completion of adjustment, reseal using sealing wax or an equivalent material.

REFERENCE TO LOCAL REGULATIONS

The installation and maintenance of the appliance must be carried out by a qualified skilled technician in accordance with the

regulations in force, and in particular:

- Decree of 2 August 1977

Technical and Safety Rules applicable to fuel gas and liquefied hydrocarbon installations located within residential buildings

and outbuildings.

- Standard DTU P 45 - 204

Gas installations (formerly DTU no. 61-1 - Gas installations April 1982 + supplement no. 1 of July 1984).

- Departmental Health Regulations

For appliances connected to the mains electricity supply.

- Standard NF C 15-100

Low-voltage electrical installations - Standards.

Ensure that the installation and gas connections are performed by a qualified technician, following the manufacturer’s

instructions and in compliance with current local safety regulations.

AFTER-SALES SERVICE

TROUBLESHOOTING GUIDE

If the hob will not operate correctly, before calling the After-Sales Service, refer to the Troubleshooting Guide to determine

the problem.

1. The burner fails to ignite or the flame is not even

Check that:

• The gas or electrical supplies are not shut off and especially that the gas supply tap is open.

• The gas cylinder (liquid gas) is not empty.

• The burner openings are not clogged.

• The plug end is not dirty.

• All the burner parts have been positioned correctly.

• There are no draughts near the hob.

2. The burner does not stay lit

Check that:

• When lighting the burner, the knob has been pressed for enough time to activate the protection device.

• The burner openings are not clogged near the thermocouple.

• The end of the safety device is not dirty.

• The minimum gas setting is correct (see relevant paragraph).

3. The containers are not stable

Check that:

• The bottom of the container is perfectly flat

• The container is centered on the burner.

• The grids have not been exchanged or positioned incorrectly.

If after the above checks the fault still occurs, get in touch with the nearest After Sales Service.

CLEANING THE HOB SURFACE

• All the enamelled and glass parts should be cleaned with warm water and neutral solution.

• Stainless steel surfaces may be stained by calcareous water or aggressive detergents if left in contact for too long.

Any food spills (water, sauce, coffee, etc.) should be wiped away before they dry.

• Clean with warm water and neutral detergent, and then dry with a soft cloth or chamois. Remove baked-on dirt with

specific cleaners for stainless steel surfaces.

NOTE: clean stainless steel only with soft cloth or sponge.

• Do not use abrasive or corrosive products, chlorine-based cleaners or pan scourers.

• Do not use steam cleaning appliances.

• Do not use flammable products.

• Do not leave acid or alkaline substances, such as vinegar, mustard, salt, sugar or lemon juice on the hob.

CLEANING THE HOB PARTS

• Grids, burner caps and burners can be removed to be cleaned.

• Clean them by hand with warm water and non-abrasive detergent, removing any food residues and checking that none

of the burner openings is clogged.

• Rinse and dry.

• Refit burners and burner caps correctly in the respective housings.

• When replacing the grids, make sure that the panstand area is aligned with the burner.

• Models equipped with electrical ignition plugs and safety device require thorough cleaning of the plug end in order to

ensure correct operation. Check these items frequently, and if necessary, clean them with a damp cloth. Any baked-on

food should be removed with a toothpick or needle.

NOTE: to avoid damaging the electric ignition device, do not use it when the burners are not in their housing.

• This hob has been designed, constructed and marketed in compliance with:

- safety requirements of “Gas” Directive 2009/142/EC (ex: EEC 90/396);

- safety objectives of the “Low Voltage” Directive 2006/95/CE (which replaces 73/23/CEE and subsequent

amendments);

- protection requirements of EEC Directive “EMC” 2004/108/EC.

Disposal of packing material

The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of the packing must

therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.

Scrapping the product

- This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment

(WEEE).

- By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the

environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

- The symbol on the product or on the accompanying documentation indicates that it should not be treated as

domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic

equipment.

Before calling the After-Sales Service, make sure you can give the following information:

- type of fault or problem;

- exact model (written on the label affixed to the instruction/warranty);

- service number that follows the word SERVICE on the rating plate under the hob and

on the label affixed to instruction/warranty;

- your complete address and phone number.

If any repairs are required, please contact an authorised After-Sales Service, as indicated in

the warranty.

WARNING

Disconnect power before servicing.

DECLARATION OF CONFORMITY

SAFEGUARDING THE ENVIRONMENT

Symbols

PRATICAL ADVICE FOR USING THE BURNERS

IMPORTANT: WHEN THE HOB IS IN USE, THE ENTIRE HOB AREA MAY BECOME HOT.

• To ignite one of the burners, turn the relative knob anti-clockwise to the maximum flame setting.

• Press the knob against the control panel to ignite the burner.

• After the burner has ignited, keep the knob pressed for about 5-10 seconds to allow proper device operation.

This burner safety device shuts off the gas supply to the burner if the flame goes out accidentally (because of sudden

draught, an interruption in the gas delivery, boiling over of liquids, etc.).

• The knob must not be pressed for more than 15 sec. If, after that time has elapsed, the burner does not remain lit,

wait at least one minute before trying to light it again.

NOTE: should particular local conditions of the delivered gas make the ignition of burner difficult, it is advisable to repeat

the operation with the knob turned to small flame setting.

The burner might go out when the knob is released. This means that the safety device has not warmed up enough. In this

case, repeat the operations described above.

OPERATION OF THE ELECTRIC HOTPLATE

• Set the knob to one of positions 1-6, which correspond to different temperatures.

• To switch off the hotplate, set the knob to position “0”.

DIMENSIONS AND DISTANCES TO BE MANTAINED (mm)

PRODUCT DESCRIPTION

1. Removable panstand grids

2. Semi-rapid burner

3. Rapid electric hotplate

4. Rapid burner

5. Semi-rapid burner

6. Rapid burner control knob

7. Electric hotplate control knob

8. Semi-rapid burner control knob

9. Semi-rapid burner control knob

10. Pilot lamp for electric hotplate

Shaded circle Tap closed

Large flame and star Maximum opening/delivery and electric ignition

Small flame Minimum opening or reduced delivery

This hob has burners of different diameters. For better burner performance,

please stick to the following rules:

- Use pots and pans with bottoms the same width as that of the burners or

slightly larger (see table on the right).

- Only use flat-bottomed pots and pans.

- Use the correct amount of water for cooking foods and keep the pot

covered.

- Make sure pots on the grates do not protrude beyond the edge of the hob.

IMPORTANT: improper use of the grids can result in damage to the hob: do

not position the grids upside down or slide them across the hob.

Do not use:

- Cast iron griddles, ollar stones, terracotta pots and pans.

- Heat diffusers such as metal mesh, or any other types.

- Two burners simultaneously for one receptacle (e.g. fish kettle).

Burner Pot Ø

Rapid From 24 to 26 cm

Semi-rapid From 16 to 22 cm

HOW TO USE THE HOB

WARNING

Do not let the burner flame extend beyond the edge of the pan.

NOTE: in case of installation of a hood above the cooktop,

please refer to the hood instructions for the correct

distance.

INJECTORS TABLE CATEGORY II2E+3+

Type of gas used Type of burner Injector

marking

Rated thermal

flow rate

Rated

consumption

Reduced heat

capacity

Gas pressure

mbar

kW BE FR min. rat. max.

NATURAL GAS

(Methane) G20

Rapid 129 B 3.00 286 l/h 0.80 0.60

17 20 25

Semi-rapid 97 1.65 157 l/h 0.45 0.35

NATURAL GAS

(Methane) G25

Rapid 129 B 3.00 332 l/h 0.60

20 25 30

Semi-rapid 97 1.65 183 l/h 0.35

LIQUEFIED

PETROLEUM GAS

(Butane) G30

Rapid 86 3.00 218 g/h 0.60

20 28-30 35

Semi-rapid 65 1.65 120 g/h 0.35

LIQUEFIED

PETROLEUM GAS

(Propane) G31

Rapid 86 3.00 214 g/h 0.60

25 37 45

Semi-rapid 65 1.65 118 g/h 0.35

Type of gas used Model

configuration

Rated thermal

flow rate (kW)

Total rated

consumption

Air required (m

) for

burning 1 m

of gas

G20 20 mbar 4 burners + 1 E 6.30 600 l/h 9.52

G25 25 mbar 4 burners + 1 E 6.30 698 l/h 8.187

G30 28-30 mbar 4 burners + 1 E 6.30 458 g/h 30.94

G31 37 mbar 4 burners + 1 E 6.30 450 g/h 23.80

ELECTRIC SUPPLY: 220-240 V ~ 50/60 Hz

Whirlpool AKM 404/NB/01 Program Chart

Brand: Whirlpool

Model: AKM 404/NB/01

Category: Hobs

Type: Program Chart

Download PDF

report

Whirlpool AKM 404/NB/01 Program Chart

Whirlpool AKM 404/NB/01 Program Chart

Related papers

Other documents