Ares Gamma V2 Float Set Quick start guide

Brand: Ares

Model: Gamma V2 Float Set

Type: Quick start guide

QUICK-START GUIDE

For more great Ares products, just visit: www.Ares-RC.comFor more great Ares products, just visit: www.Ares-RC.com

Product specications are subject to change without notice.

Due to ongoing development, the actual product may vary from

images shown.

This product contains chemicals known to the State of California

to cause cancer, birth defects and other reproductive harm.

This product is not a toy! (14+) Recommended for ages 14 and

up. Adult supervision required for ages under 18 years old.

Contains small parts, keep out of reach of children 3 years of

age and younger.

Distributed in the

UK by:

J Perkins Distribution Ltd,

Lenham,

Kent, UK

ME17 2DL.

www.jperkins.com

Distributed in Australia by:

Model Engines (Aust.) Pty. Ltd.,

Unit 1, 158-168 Browns Road,

Noble Park,

Victoria,

3174,

Australia.

www.modelengines.com.au

Ph (03) 8793 5555

[email protected]

Distributed in the US by:

Firelands Customer Service/Product Support

1133 Libra Drive, Lincoln, NE 68512

www.relandsgroup.com

1-800-205-6773

customerservice@relandsgroup.com

Gamma V2 Float Set AZSA1640

Quick-Start Guide

MADE IN CHINA

Gamma V2

Float Set

QUICK-START GUIDE

For more great Ares products, just visit: www.Ares-RC.comFor more great Ares products, just visit: www.Ares-RC.com

Remove the components from

the box and ensure you have the

following parts:

• Moulded oat set

• red/blue decal sheet

• 2x piano wire spacer bars

• 2x piano wire struts

• 4x strut saddle clamps

• 1x saddle clamp screw set

• 1x water rudder set

• 1x 1.5mm Allen key.

This Quick Start guide is written for the Gamma V2 Float Set.

A full instruction manual is available to download from www.ares-rc.com

Unroll the self-adhesive sticker

sheet and carefully cut around the

edge of the trim stripes that match

your colour scheme. Apply the

stripe to the upper, outer edge of

each oat, starting at the front and

carefully peeling the backing paper

away as you work your way back.

With the trim stripes correctly

applied each oat will be a handed

mirror image of the other.

Slot one piano wire spacer bar

into position at the front of each

oat, noting that the bar locates

in the forward slot of the two. The

remaining spacer bar locates in the

front slot of the rear oat mount.

QUICK-START GUIDE

For more great Ares products, just visit: www.Ares-RC.comFor more great Ares products, just visit: www.Ares-RC.com

Slot the piano wire spacer bar into

position at the front of each oat

noting that the strut locates in the

rearward slot behind the spacer

bar. Moving to the back of each

oat, slot the remaining strut into

position noting that it locates in the

rearward slot, behind the spacer

bar. Lock the struts and spacer

bars into position with the saddle

clamps and screws.

Your oats are now assembled

and ready to be attached to the

fuselage.

Glue the U-shape water rudder

mount over the base of the rudder

as shown, noting that it must be

located as far forward as possible

with the collet retainer positioned

at the front.

Slot the rudder shaft into the collet

at the top of the water rudder and

tighten the grub screw to clamp it

in position.

Slot the other end of the shaft

into the collet on the water rudder

mount and tighten the grub screw

to clamp it in position.

QUICK-START GUIDE

For more great Ares products, just visit: www.Ares-RC.comFor more great Ares products, just visit: www.Ares-RC.com

Slot the piano wire oat struts

into the mounts on the underside

of the fuselage and clamp them

in place using the four washer

head screws.

When tting the water rudder take

special care to ensure that it’s

perfectly aligned with the primary

air rudder. Adjust as necessary.

Your Gamma is now ready for a

swim. For the rst few ights pick

a relatively calm day when steering

and maneuvering for take-off will be

much easier. Always position your

Gamma dead into wind for take-off

and landing. At the start of your

take-off run hold in full up elevator

to raise the nose, then ease the

elevator off (as you would to raise the tail of a conventional tail-dragger)

as the Gamma gains speed and rises onto the step. Finally, gently re-apply

elevator to lift clear of the surface and enjoy ying off water.

Ares Gamma V2 Float Set Quick start guide

Ares Gamma V2 Float Set Quick start guide

Ares Gamma V2 Float Set Quick start guide

Related papers

Other documents