2. RTS
  3. Omi - adam-m

RTS Omi - adam-m User manual

  • Hello! I am an AI chatbot trained to assist you with the RTS Omi - adam-m User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Quick Start Guide
OMI - OMNEO Matrix Interface
Included:
• SafetyInstructionsST-CO
• OMIQuickStartGuide
• OMIDocumentationResourceDisk
• 2-ScrewPanhead,M2.5x10.0
• BackCardAssy.,OMI
• FrontCard,64CH,OMI
or
FrontCard,48CH,OMI
or
FrontCard,32CH,OMI
or
FrontCard,16CH,OMI
Requirements:
Youmusthavethefollowing:
• Screwdriver
• AZeditversion3.5
• IPEditversion3.4
• MCII-eversion2.9
ADAM-M Frame Installation
Important:.....Uptofour(4)OMIcardsetscanbeused
inanADAMMframeatatime.
Toinstall the OMI card into the ADAM-M frame,do
thefollowing:
1. UsingtheInstallationCD,followtheinstructions
inthereadme.txtletoinstallalltherequired
softwareneededforOMNEOfunctionality.
2. GentlyinserttheOMI front cardintothe
appropriateADAMMslot.
NOTE:Takecaretoinsertthecardproperly,asshown.
3. Usingthecardejectorstightendownthefront card
by pushing it into the slot.
4.
OnthebackoftheADAM-Mframe,carefullyinsert
theOMI back card,takingcaretoalignitwiththe
OMIfrontcard,asshownabove.
5. EnsuretheOMI back cardisseatedproperly
againsttheOMIfrontcardandissittingrmlyin
theframe.
6. Usingthesuppliedscrews,tightentheOMI back
cardtotheframe.
7. Ensurethecard ejectorsaretightenedtothe
chassisontheOMIfrontcard.
F01U273977Rev05 07/2014
Quick Start Guide
OMI - OMNEO Matrix Interface
ADAM Frame Installation
Important:....Uptoeight(8)OMIcardsetscanbe
usedinanADAMframeatatime.
Toinstall the OMI card into the ADAM frame,dothe
following:
1. GentlyinserttheOMI front cardintothe
appropriateADAMslot.
2. Usingthecardejectors.tightendownthefront
card.
3. OnthebackoftheADAMframe,carefullyinsert
theOMI back card,aligningitwiththeOMIfront
card.
4. EnsuretheOMI back cardisseatedproperly
againsttheOMIfrontcardandissittingrmlyin
theframe.
5. Usingthesuppliedscrews,tightentheOMI back
cardtotheframe.
6. Ensurethecard ejectorsaretightenedtothe
chassisontheOMIfrontcard.
Quick Start Guide
OMI - OMNEO Matrix Interface
Cabling
DB-9 Connector Pinouts
RS-232 Mode
Pin1...............................................................................N/A
Pin2..................................................... RS232-TXDOutput
Pin3........................................................RS232-RXDInput
Pin4...............................................................................N/A
Pin5.........................................................................Ground
Pin6...............................................................................N/A
Pin7...............................................................................N/A
Pin8...............................................................................N/A
Pin9...............................................................................N/A
RS-485 Mode
Pin1...............................................................................N/A
Pin2....................................................................... RS485+
Pin3........................................................................ RS485-
Pin4...............................................................................N/A
Pin5.........................................................................Ground
Pin6...............................................................................N/A
Pin7...............................................................................N/A
Pin8...............................................................................N/A
Pin9...............................................................................N/A
Ethernet 1000/100/10
Pin1BI_DA+...................................... Bi-directionalpairA+
Pin2BI_DA-........................................ Bi-directionalpairA-
Pin3BI_DB+...................................... Bi-directionalpairB+
Pin4BI_DC+...................................... Bi-directionalpairC+
Pin5BI_DC-........................................Bi-directionalpairC-
Pin6BI-DB-......................................... Bi-directionalpairB-
Pin7BI_DD+...................................... Bi-directionalpairD+
Pin8BI_DD-........................................Bi-directionalpairD-
Conguration
ConsulttheOMITechnicalManual(P/NF.01U.261.047)
forspecicinstructionstocompletethefollowingsteps.
Tocongure the OMI card in AZedit,dothefollowing:
Step1: DownloadtheLicenseFileformorechannels,if
applicable.
Step2: AssignportstothecardusingthePort
Allocationtable.
Step3: Setupthenetworkconguration.
Step4:CongureKeypanelstotheOMIcards.
Tocongure the OMI card in IPedit,dothefollowing:
Step1: UsingAZedit,downloadtheLicenseFilefor
morechannels,ifapplicable.
Step2: AddtheOMItoIPedit,usingAddDevice.
Step3: Setupthenetworkconguration.
Step4: CongurekeypanelstotheOMIcards.
System Drawing
Singlesubnetsystemwithlessthan128OMNEO
nodes:
For the most current user documentation,
rmware, and software, visit
www.rtsintercoms.com.
/