E
ELLIPTICAL
8
E35
ASSEMBLY
Customerservice1‐888‐707‐1880
1
2
INCLINERAIL&CONSOLE
MAST
SeePage9forIllustration
1. InstalltheInclineRailAssembly(2)intotheU‐channelbracketoftheMain
Frame(1).Securewiththesixbolts&associatedhardwareasfollows:From
thesides,installtwoHexHeadBolts(133)withtwoFlatWashers(164)and
twoNylonNuts(157).
Fromthetop,installfourHexHeadBolts(135),four
SplitWashers(182),fourFlatWashers(170),andfourStarWashers(183).
TightenwiththeWrenchespr ovided(184&187).
2. Connectthe3‐wireharness:InclineMotorPowerCord(48)tothefemale
receivercablecomingfromtheInclineRailAssembly(2).ConnecttheThree
pinpositionSensorconnector:InclineMotorConnectingWire(49)tothe
femalereceivercomingfromtheInclineRailAssembly(2).
3. RuntheComputerCable(50)throughtheConsoleMast(12),andpullthe
oppositeendofthistwist,tiedupontheConsoleMast(12),untilthecable
exitsthetop.InstalltheConsoleMast(12)intothereceivingbracketonthe
topoftheMainFrame(1).InstallfourSocketHeadCapBolts(125)withfour
SplitWasher
(180)andfourFlatWashers(164).TightenwiththeprovidedL
AllenWrench(217).Pullslightlyonthecomputercableatthetopofthe
mastwhileinstalling.Thiswillensurethecabledoesnotgetpinchedand
shortedduringconsolemastassembly.
4. InstalltheBottleHolder
(94)totheConsoleMast(12)withtwoPhillipsHead
Screws(141)andtightenwiththeprovidedPhillipsHeadScrewdriver(186).
*Pleasenotethatthebottleholdermustbeassembledbeforeconsole
assembly.
5. Plugalloftheconnectorsintothebackoftheconsole,including:
the
ComputerCable(50),twoHandpulseCables(57,57‐1),ResistanceSwitch
Wire(60)andtheInclineSwitchWire(61).SecuretheConsole(45)onthe
consolemountingplatewithfourPhillipsHeadScrews(141).Tightenthem
withthePhillipsHeadScrewdriver(186).
LOWER
HANDLEBARARMS
SeePage9forIllustration
1. InstalltwoWaveWashers(216)ontheLeftandRightsidesoftheHandlebar
axle.
2. SlidetheLeft(13)andRight(14)lowerhandlebarsontotheappropriatesideof
theaxle.ThehandlebarshaveasmallstickeronthemindicatingL(left)andR
(right).
Makesurethehandlebarsarefacingthecorrectdirection–seeillustration.
3. Inthethreadedholesintheendsoftheaxle,installtwoFlatWashers(165)
ontothetwoHexHeadBolts,(132).Tightenwithawrench(187).
4. Ontherod‐endoftheLowerHandlebar(13&14),untiethewireholdingthe
RodEnd
Sleeve(24).Aligntheholesintherodendswiththeholesinthe
bracketsoftheleftandrightHandlebar(13&14).Theendoftheconnecting
armsshouldbepositionedinsidetheHandlebarbracket.SecurewithaHex
Headbolt(134),FlatWasher(170
)andNylonNut(159)usingtheWrenches
provided(184&187).
HARDWARESTEP1
#125.3/8”x3/4””
SocketHeadCapBolt
(4pcs)
#133.3/8”x1‐1/2”
HexHeadBolt(2pcs)
#135.5/16”x2‐1/4”
HexHeadBolt(4pcs)
#141.M5x10mm
PhillipsScrew(6pcs)
#157.3/8”x7T
NylonNut(2pcs)
#164.3/8”
x19x1.5T
FlatWasher(6pcs)
#170.5/16”x20x1.5T
FlatWasher(4pcs)
#180.3/8”x2T
SplitWasher(4pc)
#182.5/16”x1.5T
SplitWasher(4pcs)
#183.5/16”
StarWasher(4pcs)
HARDWARESTEP2
#132.3/8”x3/4”
HexHeadBolt(2pcs)
#134.5/16”x1‐1/4”
HexHeadBolt(2pcs)
#159.5/16”x7T
NylocNut(2pcs)
#165.3/8”x30mm
FlatWasher(2pcs)
#170.5/16”x20x1.5T
FlatWasher(2pcs)
#216.Ø25
Wave
Washer(2pcs)