Crest X 20R User manual

owner’s manual

X-Rackrack mount mixers

XR-20

XR-24

1

Save the carton and packing materials!

Should you ever need to ship the unit,

use only the original factory packing.

For replacement packaging, call Crest Audio’s

Customer Service Department directly.

2

Read all documentation before

operating your equipment.Retain all

documentation for future reference.

3

Follow all instructions printed on

unit chassis for proper operation.

4

Do not use the unit if the electrical

power cord is frayed or broken.

The power supply cord should be rout-

ed so that it is not likely to be walked on

or pinched by items placed upon or

against it.

5

Always operate the unit with the

AC ground wire connected to the

electrical system ground.Precautions

should be taken so that the means of

grounding of a piece of equipment is not

defeated.

6

Damage caused by connection to

improper AC voltage is not covered

by any warranty.

7

Do not spill water or other liquids

into or on the unit, or operate the

unit while standing in liquid.

8

The power cord of equipment

should be unplugged from the out-

let when left unused for a long peri-

od of time.

Service Information

Do not open unit!

Opening the unit will expose you to

potentially dangerous voltages. There are

no user serviceable parts inside.

Equipment should be serviced by

qualified service personnel when:

A.The equipment has been exposed to rain.

B.The equipment does not appear to oper-

ate normally, or exhibits a marked change in

performance.

C.The equipment has been dropped, or the

enclosure damaged.

To obtain service:

contact your nearest Crest Audio

Service Center, Distributor, Dealer,

or Crest Audio at 201.909.8700

USA

or visit www.crestaudio.com for addi-

tional information.

email techserve

@crestaudio.com

This symbol is used to alert

the operator to follow important

procedures and precautions

detailed in documentation.

This symbol is used to warn opera-

tors that uninsulated “dangerous

voltages” are present within the

equipment enclosure that may

pose a risk of electrical shock.

XR-20 / XR-24 owner’s manual

Important precautions

IIMMPPOORRTTAANNTT SSAAFFEETTYY IINNSSTTRRUUCCTTIIOONNSS

WWAARRNNIINNGG::

When using electrical products, basic cautions should always be followed, including the following:

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one

wider than the other. A grounding type plug has two blades and a third grounding plug. The wide blade or third

prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the

point they exit from the apparatus.

11. Only use attachments/accessories provided by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When

a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in

any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the

apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Never break off the ground pin. Write for our free booklet “Shock Hazard and Grounding.” Connect only to a power

supply of the type marked on the unit adjacent to the power supply cord.

16. If this product is to be mounted in an equipment rack, rear support should be provided.

17. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in

susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently

intense noise for a sufficient time. The U.S. Government’s Occupational and Health Administration (OSHA) has

specified the following permissible noise level exposures:

Duration Per Day In Hours Sound Level dBA, Slow Response

890

692

495

397

2 100

1 1/2 102

1 105

1/2 110

1/4 or less 115

According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Ear plugs or protectors to the

ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss, if exposure

is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is

recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be

protected by hearing protectors while this unit is in operation.

SSAAVVEE TTHHEESSEE IINNSSTTRRUUCCTTIIOONNSS!!

4

1

2

3

Master section P .27

Aux masters, groups, main outs, monitor section.

Front panel controls and rear panel connectors.

Stereo Input channels p.17

Front panel controls and rear panel connections

Mono Input channels p. 7

Front panel controls and rear panel connections

table of contents

Introduction

Thank you and congratulations on your purchase of your new

Crest Audio X-Rack mixer. We’re confident that you will enjoy

many years of trouble-free service from it. You will quickly find

that it fits into a wide variety of mixing applications with ease.

Due to well thought out sets of features, coupled with intelli-

gent circuit design and the highest standards in construction &

workmanship, all Crest Audio console products excel above and

beyond the competitor’s products, in every area.

This owner’s manual covers both the XR-20 and the XR-24 X-

Rack mixers. Features are identical for both models, the only dif-

ference is the amount of Mono Inputs versus Stereo Inputs. The

XR-20 has 12 Mono inputs and 4 Stereo inputs, adding up to a

total of 20 microphone inputs. The XR-24 has 8 Mono inputs

and 8 Stereo inputs, adding up to a total of 24 microphone

Inputs.

Please read this manual thoroughly and keep it handy for future

reference. If you have any operating concerns that are not cov-

ered in this manual, or have application questions of any type,

don’t hesitate to contact Crest Audio directly either by phone,

fax, or email. Here is our technical support contact information:

Phone: (201) 909 8700

Fax: (201) 909 8744

Email: [email protected]m

Specifications P. 47

XR-20 / XR-24 owner’s manual

p.4

XR-20/24 block diagram

JIMI

how to use this manual

format

This manual uses a format that is intended to be easy to read, yet technical for those

who need to know all the details. For feature descriptions, this is done by devoting the

left side of each page to 1) an overall module picture, 2) a block diagram, and 3) a con-

trol closeup. These images all pertain to the features and control descriptions on the

right side of the page. The intention is to make the manual easy to read while including

all the technical details needed for getting the most out of the X-Rack - a compact, flexi-

ble, feature-rich addition to Crest Audio's growing line of audio mixing console products.

conventions

Control Icons

This manual uses symbols to illustrate what the control descriptions are referring to. This

makes it possible to avoid redundant wording and makes the control descriptions clear.

Switch in the UP, non-activated position

Switch in DOWN, activated position

Switch that illuminates when in the DOWN position

Momentary switch that illuminates when activated

LEDthat is on, indicating that it's associated feature is activated

Potentiometer

Standard 1/4" TRSjack (used for line level inputs and insert sends)

1/4" TRSjack with normal switching (used on insert returns)

Female XLRinput jack

Male XLRoutput jack

p.5

Mono input channel

1

p.6

XR-20 / XR-24 owner’s manual

BAL MIC IN

BAL LINE IN

INPUT

PREAMP

GAIN

12 - 70 dB

HPF

LINE

27dB

PAD

+48V ON

HPF

70Hz

-18dB/Oct

+48V

Module

Block diagram

Controls

Front panel features

Mono Input channel features are identical for both the XR-20 and the XR-24. The XR-20

has 12 Mono inputs and the XR-24 has 8 Mono inputs.

Line Input (mic pad)

The input preamp circuit is set up to accept a mic-level signal. This signal is

brought in via the XLR mic-input connector located on the rear panel. The 1/4"

TRS input jack is disabled.

The input preamp circuit is set up to accept a line-level signal from either

the XLR mic-input connector or the 1/4" TRS input jack, both located on the rear

panel. Since the sensitivity of the input preamp is reduced, this control can also act

as a PAD for bringing a very hot microphone feed down to a controllable level,

avoiding overload. When a plug is inserted into the 1/4" TRS input jack, the XLR

mic-input connector is disabled.

Gain

The Input gain control is used to establish proper gain structure in the chan-

nel. For best results, use the Solo system to monitor the channel while you set

the gain. The goal is maximum gain without distortion. Both the main LED meters

(during Solo) and the channel’s Level/Peak indicator can be used for adjusting gain.

70 Hz high-pass filter

The high-pass filter reduces or eliminates unwanted low frequencies without sub-

stantially affecting the program material. Quite often such unwanted low frequen-

cies are included with mic- or line-input signals. For example, stage rumble or

wind can be picked up through vocal mics. The cut-off frequency of the high-pass

filter is 70 Hz and the slope is -18dB per octave.

HPF

High-pass filter is on.

Mono Input channel

1

p.7

Mono input channel

1

p.8

XR-20 / XR-24 owner’s manual

FOUR BAND EQ

LEVEL

LF LOW MID HI MID HF

EQ ON

FREQ LEVEL LEVELFREQ LEVEL

12 KHZ400 - 8 KHZ80 - 2 KHZ80 HZ

Module

Block diagram

Controls

Front panel features

EQ

Many audio signals coming into the console require some degree of corrective eq

in order to be part of a good sounding mix. XR-20 & XR-24 offer a very useful

and great sounding eq section on each channel. The input EQ consists of four

bands: High, High-mid, Low-mid and Low. The High and Low frequency bands each

have a boost/cut control and their frequencies are fixed. The High-mid and Low-

mid bands each have variable boost/cut and variable frequency.

high frequency—HF

Boost / Cut15dB boost and cut. Shelving @ 12 kHz

high mid—HM

FrequencyContinuously sweepable between 400 Hz and 8 kHz.

Boost / Cut15dB boost and cut. Bell curve with a Q of 1

Low mid—LM

FrequencyContinuously sweepable between 100 Hz and 2 kHz.

Boost / Cut15dB boost and cut. Bell curve with a Q of 1

Low frequency—LF

Boost / Cut15dB boost and cut. Shelving @ 80 Hz.

EQ on

Equalizer is on. This switch is used to activate the EQ section and can be

used to make A/B comparisons between "flat" and eq'd signals.

p.9

Mono Input channel

1

p.10

Mono input channel

1

XR-20 / XR-24 owner’s manual

HF

PRE-SOURCE

SELECT

PRE

SOURCE

MUTE ?

PAN

+10

MONO L-R G1-2

M

U

T

E

EQ ON

FADER AMP

PRE-SOURCE

BUFFER

NO

YES

AUX SENDS

1 THRU 6

G3-4

BUS ASSIGN

SWITCHES

12 KHZ

CHAN

FADER

A1-2

PRE

A3

A4

A3-4

PRE

LEV 3

LEV 4

A5

A6

A5-6

PRE

LEV 5

LEV 6

PRE

FADER

PRE

EQ

PRE

INSERT

100MM

LEVEL

1-2

A1

A2

PAN

1-2

Module

Block diagram

Controls

AUX send features

Six auxiliary sends are available for creating individual output mixes. These can be

used to drive effects processors, provide monitor mixes, create broadcast or

alternate sound reinforcement mixes, or for other special requirements.

Note: The default PRE setting for the Auxes is pre-fader, but post-mute,

post-insert, and post eq. Internal settings can be changed so that PREis also pre-

eq and pre mute

Aux 1 - 2 PRE

AUX 1/2 stereo pair is post fader

AUX1/2 stereo pair is pre-fader

Aux sends 1 & 2

Auxes 1 and 2 are configured as a stereo pair. The top knob controls the level

and the bottom knob acts as a PANcontrol. This stereo aux send can be used for

any type of stereo feed from the console, such as live two-track recording, stereo

in-ear monitors, alternate stereo feed for broadcast, and stereo signal processors.

Also, by properly using the pan control Auxes 1 and 2 can be used as discrete

mono Aux buses

Aux 1/2 level Send level for the Aux 1/2 stereo pair

Aux 1/2 PAN Stereo placement for the Aux 1/2 stereo pair

AUX 3-4 PRE

AUX 3 and AUX 4 are post fader

AUX3 and AUX 4 are pre-fader

Aux sends 3, 4, 5 & 6

Auxes 3, 4, 5, & 6 are configured as descrete mono aux sends. They are typically

used to feed signal processors and for on-stage monitors.

Auxes 3, 4, 5, &6 level Set levels Auxes 3, 4, 5, & 6.

AUX 5-6 PRE

AUX 5 and AUX 6 are post fader.

AUX5 and AUX 6 are pre-fader.

p.11

Mono Input channel

1

p.12

Mono input channel

1

XR-20 / XR-24 owner’s manual

PRE-SOURCE

SELECT

PRE

SOURCE

MUTE ?

SOLO DC

PAN

+10

MONO L-R G1-2

MUTE

EQ ON

FADER AMP

PRE-SOURCE

BUFFER

NO

YES

SOLO LEFT

AUX SENDS

1 THRU 6

SOLO RIGHT

G3-4

BUS ASSIGN

SWITCHES

PFL

CHAN

FADER

A1-2

PRE

A3

A4

A3-4

PRE

LEV 3

LEV 4

A5

A6

A5-6

PRE

LEV 5

LEV 6

PRE

FADER

P

RE

E

Q

100MM

TO

PEAK

CIRCUIT

LEVEL

1-2

A1

A2

PAN

1-2

Module

Block diagram

Controls

Bus assignment features

The bus assignment section offers considerable flexibility for creating what even-

tually becomes the main output mix. Two stereo subgroups are available for creat-

ing submixes or separate stereo mixes. All assignments are derived post-fader,

post-eq, and post-mute.

PAN control

The pan control positions the signal within the stereo left/right (or

odd/even) field. PAN affects signals that are assigned directly to Left-Right, Groups

1-2 and Groups 3-4

Mono bus assign

The channel is assigned to the MONOmix bus. PANhas no affect on

MONO

L-R bus assign

The channel is assigned to the Left and Right mix buses.

G 1-2 bus assign

The channel is assigned to Groups 1 and 2. Groups 1 and 2 are configured

as a stereo pair. They can also be treated as two discrete mono groups by using

the PAN control.

G 3-4 bus assign

The channel is assigned Groups 3 and 4. Groups 4 and 4 are configured as a

stereo pair. They can also be treated as two discrete mono groups by using the

PAN control.

Input fader (100mm)

The fader is the primary level control for signals being sent to any of the consoles

post fader mix buses,

MUTE

The input channel is muted and the MUTELEDis alluminated. All AUX

feeds and bus assignments are shut off. Insert send and SOLO signals are still

active.

PK / SIG LED indicator

This two-color(green & red) LED is used to monitor the channel’s signal

level. Signal present (green) is monitored pre-fader. Peak (red) is monitored at the

preamp and before & after the fader.

PFL

PFL -Pre fader listen. This button routes the channel’s signal to the Solo bus

for monitoring through headphones or in the control room. The Peak (red) LED

is illuminated to show PFLstatus.

p.13

Mono Input channel

1

p.14

Mono input channel

1

XR-20 / XR-24 owner’s manual

Rear panel

Block diagram

Connectors

BAL MIC IN

BAL LINE IN

INPUT

PREAMP

GAIN

12 - 70 dB

HPF

LINE

27dB

PAD

DIRECT OUT

INSERT

SEND / RTN

HPF

70Hz

-18dB/Oct

GC

DIRECT OUT

SOURCE

POST

FADER

PRE

FADER

REAR PANEL

BA L MIC IN

BA L LINE IN

INPUT

PREA MP

GA IN

12 - 70 dB

FOUR BAND EQ

LEV EL

LF LOW MID HI MID HF

HPF

LINE

27dB

PA D

PRE-SO URCE

SELECT

PRE

SOURCE

M UTE ?

SOLO DC

DIRECT OUT

PA N

+10

MO NO L-R G1-2

MUT E

INSERT

SEND / RTN

+48V ON

EQ O N

FADER A M P

PRE-SOURCE

BUFFER

NO

YES

SOLO LEFT

X-RACK MONO INPUT MODULE

12 O R 8 M O NO INP UT S A V A ILA B LE

HPF

70Hz

-18dB/O ct

FREQ

INPUT

SIGNA L

LED

PRE

FADER

POST

FADER

AUX SENDS

1 THRU 6

LEV EL LEVELFREQ LEVEL

SOLO RIGHT

G3-4

BUS A SS IG N

SW IT CHES

12 KHZ400 - 8 KHZ80 - 2 KHZ80 HZ

PFL

SOLO

TRIG GER

CHA N

FADER

G C

A1-2

PRE

A 3

A 4

A3-4

PRE

LEV 3

LEV 4

A 5

A 6

A5-6

PRE

LEV 5

LEV 6

PRE

FADER

PRE

EQ

PRE

INSERT

DIRECT OUT

SOURCE

POST

FADER

PRE

FADER

REAR PANEL

100MM

PEA K

(PFL)

SIG

TO

PEA K

CIRCUIT

R

G

+48V

LEV EL

1-2

A 1

A 2

PA N

1-2

p.15

Mono Input channel

1

Rear panel features

48 V Phantom power

48 volts DC is applied to pins 2 and 3 on the mic-input XLRconnector. This

option is used with condenser microphones and active direct boxes that require

an external DC voltage (phantom power ) in order to operate.

Line INPUTjack

Line-level signals, balanced or unbalanced, may be brought into the

input channel through this jack. The LINE INPUT switch must be pressed for this

jack to be active.

MIC INPUT jack

This balanced female XLR accepts a low-impedance microphone signal, or a

line-level signal, depending on the position of the LINEINPUTswitch on the front

panel.

INSERT jack

This switching 1/4” TRS jack allows an external signal processor to be

inserted into the signal path of the channel. The tip carries the SEND signal and

the ring carries the RETURN signal.

DIRECTOUT jack

The channel’s signal can be brought out of the console via the direct

out jack. The signal that appears at this jack is normally post fader. There is an

internal option for making it pre fader.

Stereo input channel

1

p.16

XR-20 / XR-24 owner’s manual

Module

Block diagram

Controls

BAL MIC IN

BAL LINE IN

GAIN

15 - 60 dB

LINE

27dB

PAD

+48V ON

MONO

BAL MIC IN

BAL LINE IN

INPUT

PREAMP

27dB

PAD

BAL

LEFT

RIGHT

PRE

EQ

INPUT

SIGNAL

LED

PEAK

(PFL)

S

I

G

R

+48V

Front panel features

Stereo Input channels features are identical for both the XR-20 and the XR-24. The XR-

20 has 4 Stereo inputs, and the XR-24 has and 8 Stereo inputs. On both models the

Stereo inputs are

located to the left of the master section, to the right of the Mono

inputs. They can be treated as mono input channels, or as Stereo input channels.

Stereo Line Input (mic pad)

The stereo input preamp circuit is set up to accept mic-level signals. The sig-

nals are brought in via the XLR mic-input connectors located on the rear panel.

The 1/4" TRS input jacks are disabled.

The stereo input preamp circuits are set up to accept line-level signals from

either the XLR mic-input connectors or the 1/4" TRS input jacks, all located on

the rear panel. Since the sensitivity of the stereo input preamp is reduced, this

control can also act as a PAD for bringing very hot microphone feeds down to a

safe level, avoiding overload. When a plug is inserted into a 1/4" TRS input jack, the

XLR connector is disabled.

Gain

The Input gain control is used to establish proper gain structure in the chan-

nel. The GAINcontrol affects both the Left and Right input signals. For best

results, use the Solo system to monitor the channel while you set the gain. The

goal is maximum gain without distortion. Both the main LED meters (during Solo)

and the channel’s Level/Peak indicator can be used for adjusting gain.

SUM INPUTS

By summing the inputs, a stereo input channel can be used as a mono input chan-

nel.

The channel functions as a stereo input.

If signals are applied to both the Left and Right input jacks, they will be

summed together as a mono signal. If a signal is applied to just one of the input

jacks, it will be treated as a mono signal throughout the rest of the channel.

Stereo Input channel

1

p.17

Stereo input channel

1

p.18

XR-20 / XR-24 owner’s manual

Module

Block diagram

Controls

FOUR BAND EQ - LEFT

LEVEL

LF LOW MID HI MID HF

MUTE

EQ ON

F

A

O

NO

FREQ LEVEL LEVELFREQ LEVEL

12 KHZ400 - 8 KHZ80 - 2 KHZ80 HZ

CHAN

FADER

LF LOW MID HI MID HF

12 KHZ400 - 8 KHZ80 - 2 KHZ80 HZ

FOUR BAND EQ - RIGHT

BAL

100MM

PRE

FADER

PRE

EQ

Page is loading ...

Crest X 20R User manual

This manual is also suitable for

Crest X 20R User manual

Other documents