Haier HL22K1 User manual

Please read this manual carefully

before using this TV set and keep it

for future reference.

LCD TV & LCD TV/DVD Combo

USER MANUAL

R

HL19R1/HL19K1/HLC19R1/HLC19K1/HL22R1/HL22K1/HLC22R1

HLC22K1/HL22F1

WARNING AND CAUTION

RISK ELECTRIC SHOCK

DO NOT OPEN

CAUTION

!!

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral

triangle is intended to alert the user to the presence of

uninsulated dangerous voltage within the product s

enclosure that may be of sufficient magnitude to constitute a

risk of electric shock.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature

accompanying the appliance.

!!

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS

POLARIZED PLUG WITH AN EXTENSION CORD,

RECEPTACLE OR OTHER OUTLET UNLESS THE

BLADES CAN BE FULLY INSERTED TO PREVENT

BLADE EXPOSURE.

CAUTION: These servicing instructions are for use by qualified service

personnel only. To reduce the risk of electric shock, do not perform any

servicing other than that contained in the operating instructions unless

you are qualified to do so.

CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER

THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION

EXPOSURE. (This item is only for TV with DVD models.)

IMPORTANT SAFETY INSTRUCTIONS

Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the

manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves,

or other apparatus (including amplifiers) that produce heat.

9) Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

10) Only use attachments/accessories specified by the manufacturer.

11) Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus. When a cart is used, use caution when

moving the cart/apparatus combination to avoid injury from tip-over.

12) Unplug this apparatus during lightning storms or when unused for long

periods of time.

13) Refer all servicing to qualified service personnel. Servicing is required when

the apparatus has been damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

14)The apparatus shall not be exposed to dripping or splashing and that no

objects filled with liquids, such as vases, shall be placed on the apparatus.

15)The mains plug or appliance inlet is used as the disconnect device, remain it

readily operable during the apparatus normal use.

Safety Instructions(for TV with DVD)

PRECAUTIONS

FCC WARNING-This equipment may

generate or use radio frequency

energy.Changes or modifications to this

equipment may cause harmful

interference unless the modifications are

expressly approved in the instruction

manual.The user could lose the authority

to operate this equipment if an

unauthorized change or modification is

made.

CAUTION:USE OF CONTROLS OR

ADJUSTMENTS OR PERFORMANCE

OF PROCEDURES OTHER THAN

THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION

EXPOSURE.

LASER SAFETY

This unit employs a laser.Only a qualified

service person should remove the cover

or attempt to service this device,due to

possible eye injury.

CAUTION:VISIBLE AND INVISIBLE

LASER RADIATION WHEN OPEN AND

INTERLOCK DEFEATED.DO NOT

STARE INTO BEAM.

LOCATION:INSIDE,NEAR THE DECK

MECHANISM.

Energy Star compliant

By being Energy Star compliant you are assured that your Haier model is helping the

environment by using less energy while saving you money. ENERGY STAR is a joint

program of the U.S. Environmental Protection Agency and the U.S. Department of

Energy promoting energy efficiency.

CONTENT

Note: DVD is available only on certain models. Please refer to your original set

for specific details.

Safety Notice Items...................................................................................

Front Panel Controls..................................................................................

Connection Options...................................................................................

Remote Control ........................................................................................

Remote Control Key Functions....................................................................

Connection Instructions.............................................................................

External equipment Connections..............................................................

Antenna Connection.............................................................................

VGA Setup.............................................................................................

Component Setup................................................................................

VCR Setup...........................................................................................

HDMI Input.........................................................................................

Cable TV Setup....................................................................................

External Component Source Setup.......................................................

Basic Operating Instructions.......................................................................

Switch On/Off the TV set..........................................................................

Choose the input source..........................................................................

Audio Control..........................................................................................

Mute......................................................................................................

INFO.....................................................................................................

Select the TV Channel You Want.............................................................

Picture Mode...........................................................................................

Audio Mode............................................................................................

Sleep.....................................................................................................

GUIDE...................................................................................................

ARC button.............................................................................................

.Button...................................................................................................

CH.LIST button.......................................................................................

FAVORITE button......................................................................................

Menu Operations.......................................................................................

Video Menu Options...............................................................................

Video Menu Options Continued...............................................................

Audio Menu Options................................................................................

Audio Menu Options Continued................................................................

Channel Menu Options.............................................................................

Channel Menu Options Continued..............................................................

Function Menu Options.............................................................................

Function Menu Options Continued..............................................................

Lock Menu Options ..................................................................................

Lock Menu Options Continued..................................................................

PC Menu Options....................................................................................

PC Menu Options Continued....................................................................

............................................................

DVD Features..........................................................................................

Special Function Playback.......................................................................

DVD System Setup...................................................................................

Playable Discs.........................................................................................

Disc Protection and DVD Characteristics...................................................

Troubleshooting Guide...............................................................................

Specifications...........................................................................................

Warranty ..................................................................................................

Stream media broadcast system

1

2

3

4

5

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

23

24

28

29

30

32

34

35

38

39

40

41

42

Safety Notice Items

Incorrect usage may cause fire or electric shock.

ensure

Please keep this manual for later use;

Please comply strictly with the warning instructions on the machine and

in this book;

Before operation, please make sure that the operating voltage of your unit is

correct;

Do not remove the back cover. If service is needed, please contact an

Authorized service technician.

To prevent this, please do as

required when you are installing, using and cleaning this machine. To

your safety and extend the life-span of LCD-TV, please read the following items

carefully before using:

l Please read and understand all the instructions before operation;

l

l Please comply with the instructions provided;

l Please do not use additional devices that are not recommended by

manufacturer:

l

l Do not place the unit on unstable, dusty and humid places;

l Never put the unit in direct sunlight or near heat sources;

l Allow enough space for proper ventilation;

l Please keep water away from the LCD-TV . If water comes in contact with the

LCD-TV, disconnect the power cord from the power source, then wipe the set

with a dry soft cloth;

l

Front Panel Controls

Control Panel Function

1. POWER Press to turn on and off the TV.

2. INPUT Selects the input signals.

3. MENU Menu display. Press to access the on-screen menu display.

4. VOL- Volume down / Left button to adjust the item in the OSD.

VOL+ Volume up / Right button to adjust the item in the OSD

/Press to enter.

5. CH- TV channel down / to select the item in the menu.

CH+ TV channel up / to select the item in the menu.

6. Power indicator

7. Remote Sensor Receivers IR signals from the remote control.

Do not put anything near the sensor ,which may

block the remote control signal.

R1 series series F series K1 1

INPUT MENU VOL- VOL+ CH- CH+ POWER

COMPONENT IN

Pr Pb Y

ATN IN R-AUDIO-L R-AUDIO IN-L

PC AUDIO IN

VGA INUSB HDMI

S-VIDEO IN

VIDEO

Connection Options

The above figure is for reference

only, connections may differ

depending upon the models and

terminals of some models may be

on the back bottom of the set

DVD slot load

DVD

STOP

PLAY/PAUSE

OPEN/CLOSE

1.ANT IN(Antenna Input) Connect cable or antenna signals to the TV, either

directly or through your cable box.

2.Headphone jack : Headphone audio output terminal.

3.Audio in Connect audio output from an external device to these jacks.

4.S-VIDEO Connect S-Video out from an S-Video device to the jacks.

5.Audio in Connect audio output from an external device to these jacks.

6.Video in Connect video output from an external device to this jack.

7.USB input Connect a USB flash drive to view JPEG images or listen to MP3

songs.

8.VGA Connect to the VGA 15PIN analog output connector of a PC

graphics card to use set as a PC display.

9.PC audio in Connect the audio output from the pc to the PC audio input port.

10. HDMI: Connect a HDMI device to receive digital audio and uncompressed

digital video.

11. Component Input Connect a component video device to these jacks.

R1 series seriesK1

Insert DVD with the label side facing towards

the back. (Silver "shiny" side facing towards you)

Remote Control

Installing Batteries

Remove the battery cover.

Insert two size AAA batteries matching

the +/-polarities of the battery to the +/-

marks inside the battery compartment.

Precautions

Make sure that there is no

obstacle between the remote

controller and television set.

As strong light may interfere with the

signals, change your position to

operate the remote control if

the television cannot be turned

on or off as expected.

Keep the remote control

away from heat sources or

humid areas to ensure

effective performance of

the remote.

Make sure that two AA 1.5V or AAA

depending up the model alkaline

batteries are loaded. The batteries

must be of the same type, must be

inserted properly, and must not be

rechargeable.

1.Press to turn on and off the TV

2.Press to switch input source to USB in

3.Display the guide when you are watching analog or

digital channels

4.Select a closed caption option

5.Press repeatedly to cycle through the available picture

modes

6.Press to cycle through different sound settings

7.Show the input source

8.Switches the TV sound on or off

9.Press to adjust the volume

10.Press to open the on-screen menu

11.Thumbstick(Up/Down/Left/Right)

Allows you to navigate the on-screen menus

and adjust the system settings to your preference.

12.Press to display the sleep timer option

13.DVD PLAY/PAUSE

14.DVD Open/close

15.DVD FAST FORWARD

16.DVD FAST REVERSE

17.DVD CALL

18.DVD MENU

19.DVD SEARCH

20.DVD ANGLE

21.Press to switch input source to DVD in

22.Open the channel list in TV

23.Select MONO, STEREO, SAP in NTSC system

24.Open the favourite channel list in TV

25.Press to change the aspect ratio

26.Press to change a channel

27.Press to select digital channels. For example, to enter

“54-3”, press “54”, “ ” and “3”

28.Press to jump back and forth between two channels

29.Press to scan through channels. To scan quickly

between the last two channels, press and hold down

either +/- .

30.Exit On Screen Display

31.Accesses the highlighted item in the on-screen menu

32.Press to display the TV status information on the top

of the TV screen

33.DVD STOP

34.DVD REPEAT

35.DVD Previous Chapter

36.DVD Next Chapter

37.DVD AUDIO Mode

38.DVD SETUP

39.DVD PROGRAM

40.DVD SUBTITLE

Remote Control Key Functions

When using the remote control, aim it

towards the remote sensor on the TV

UP

DOWN

LEFT

RIGHT

(For TV with DVD)

OPEN/CLOSE

PLAY/PAUSE

REV

D.MENU

SEARCH

D.CALL

ANGLE

D.AUDIO

SUBTITLE

ENTER

STOP REPEAT

PREV NEXT

SETUP

PROGRAM

USB

GUIDE

INPUT

MUTE

VOL CH

MENU

SLEEP DISPLAY

EXIT

RECALL

PICTURE AUDIO ARC FAVORITE

CCD MTS/SAP CH.LIST

DVD

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

Remote Control Key Functions

When using the remote control, aim it

towards the remote sensor on the TV

(For TV without DVD)

PICTURE

CCD

INPUT

ARC

MENU

VOL-

EXIT

USB

PLAY/PAUSE

REV

DISPLAY GUIDE

1 2 3

4 5 6

7 8 9

MTS/SAP

CH+

CH-

VOL+

ENTER

STOP

0

AUDIO

SLEEP

REPEAT

MUTE

RECALL

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

1.Press repeatedly to cycle through the available

picture modes

2.Press to change the aspect ratio

3.Select a closed caption option

4.Show the input source

5.Press to open the on-screen menu

6.Volume/Channel Selection

7.Exit On Screen Display

8.Press to switch input source to USB in

9.DVD PLAY/PAUSE

10.DVD fast reverse

11.DVD fast forward

12.Press to display the TV status information on the top

of the TV screen

13.Shows program schedule in TV

14.Press to turn on and off the TV

15.Press to cycle through different sound settings

16.Press to display the sleep timer option

17.Select MONO, STEREO, SAP in NTSC system

18.Press to change a channel

19.Press to select digital channels. For example, to

enter “54-3”, press “54”, “ ” and “3”.

20.Switches the TV sound on or off

21.Accesses the highlighted item in the on-screen menu

22.Press to jump back and forth between two channels

23.DVD REPEAT

24.DVD STOP

25.DVD Next Chapter

26.DVD Previous Chapter

27.Open the channel list in TV

28.Open the favorite channel list in TV

Connection Instructions

External Equipment Connections

Antenna Connection

Multi-family Dwellings/Apartments

(Connect to wall antenna socket)

wall antenna

socket

VHF antenna

UHF antenna

outdoor

antenna

Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

Bronze Wire

Be careful not to bend the bronze

wire when connecting the antenna.

Bronze Wire

Turn clockwise to tighten.

RF coaxial wire (75 ohm)

To improve picture quality in a poor

signal area, purchase and install a

signal amplifier.

If the antenna needs to be split for two

Tvs, install a 2-Way Signal Splitter

in the connections.

If the antenna is not installed properly,

contact your dealer for assistance.

NOTE: Cables shown are not included with the TV

Over-the-air TV reception will depend on your antenna type, antenna location

and antenna positioning.

Connection Instructions

You can use your LCD-TV as a monitor for your personal computer using a VGA

cable (not supplied).

VGA Setup

Connection and use steps:

1.Read the user guide supplied with

your computer and ensure that it has

a VGA connector;

2.Make sure that the power of the LCD

-TV and the PC are off;

3.Connect a D type 15-pin PC interface

cable ( not supplied ) to the PC video

interface connector on the PC. Then

connect the other end to the PC video

interface connector on the back of the

LCD-TV.Tighten the screws on the PC

connectors once they are firmly

connected;

4.Turn on the power of the LCD-TV first ,

and then turn on the power of the PC;

5.Press INPUT button to set the video input mode of the LCD-TV to PC;

Once the input for PC is selected and if you see no image press function

F8 on you pc.

6.Check the image on your TV. There may be noise associated with the resolution,

vertical pattern, contrast or brightness in PC mode. If noise is present, change

the PC mode to another resolution, change the refresh rate to another rate or

adjust the brightness and contrast on the menu until the picture is clear. If the

refresh rate of the PC graphic card can not be changed, change the PC graphic

card or consult the manufacturer of the PC graphic card.

Component Setup

How to connect

Connect the DVD video outputs (Y, PB, PR)

to the Component(Y, Pb, Pr) IN jacks on

the TV and connect the DVD audio outputs

to the AUDIO IN jacks on the TV, as shown

in the figure.

NOTE: If your DVD player does not have

component video output, use S-Video.

How to use

1. Turn on the DVD player, insert a DVD.

2. Use INPUT button on the remote

control to select the proper input.

Resolution

Mode

VGA

SVGA

XGA

Resolution

640x480

800x600

1024x768

Line frequency(KHz)

31.5

37.9

48.4

Frame frequency(Hz)

60

Note: All above listed are subject to VESA criteria.

PC AUDIO IN

VGA IN

COMPONENT IN

Pr Pb Y

R-AUDIO-L

S-VIDEO IN

Connection Instructions

VCR Setup

Connection and use steps:

1.Read the user guide supplied with your AV devices and ensure that it has

Composite or S-Video connectors;

2.Make sure that the power of the LCD-TV and the AV device are off;

.Turn on the LCD-TV first ; and then turn on the

power of the AV device;

4.Press button to set

the video input mode of the

LCD-TV to S-Video mode or

Video mode.

Connection Option 1

Set VCR output switch to 3 or 4 and then

tune TV to the same channel number.

Connection Option 2

1. Connect the audio and video cables from

the VCR's output jacks to the TV input jacks,

as shown in the figure.

When connecting the TV to VCR, match

the jack colors (Video = yellow, Audio

Left = white,and Audio Right = red).

If you connect an S-VIDEO output from

VCR to the S-VIDEO input, the picture

quality is improved; compared to conne-

cting a regular VCR to the Video input.

2. Insert a video tape into the VCR and press

PLAY on the VCR. (Refer to the VCR owner s

manual.)

3

INPUT

- To avoid picture noise (interference), leave an adequate distance between the

VCR and TV

.

HDMI Input

How to connect

Connect the cables from the external equipment's

output jacks to the TV input jacks, as shown in the figure.

How to use

1. Select the input source by using button

on the remote control or on the TV.

2. Operate the corresponding external equipment.

Refer to external equipment operating guide.

INPUT

HDMI

COMPONENT IN

Pr Pb Y

ATN IN R-AUDIO-L R-AUDIO IN-L

S-VIDEO IN

VIDEO

VCR

1

2

HDMI

Connection Instructions

Cable TV Setup

- After subscribing to a cable TV service from a local provider you can watch cable

TV programming. The TV cannot display TV programming unless a TV tuner

device or cable TV converter box is connected to the TV.

- For further information regarding cable TV service, contact your local cable TV

service provider(s).

Connection Option 1

1. Select 3 or 4 with channel switch on cable

box.

2. Tune the TV channel to the same selected

output channel on cable box.

3. Select channels at the cable box or with

the cable box remote control.

Connection Option 2

1. Connect the audio and video cables from

the Cable Box's output jacks to the TV

input jacks, as shown in the figure.When

connecting the TV to a Cable Box, match

the jack colors

(Video = yellow, Audio Left = white, and

Audio Right = red).

2. Select the input source by using the

INPUT button on the remote control.

3. Select your desired channel with the

remote control for cable box.

External Component Source Setup

How to connect

Connect the audio and video cables from

the external equipment's output jacks to the

TV input jacks, as shown in the figure.

When connecting the TV to external equip-

ment, match the jack colors (Video = yellow,

Audio Left = white, and Audio Right = red).

How to use

1. Select the input source by using the INPUT

button on the remote control.

2. Operate the corresponding external equi-

pment. Refer to external equipment ope-

rating guide.

R-AUDIO IN-L VIDEO

COMPONENT IN

Pr Pb Y

ATN IN R-AUDIO-L R-AUDIO IN-L

S-VIDEO IN

VIDEO

Basic Operating Instructions

Switch On/Off the TV set

When the POWER button is pressed and the LCD-TV is turned on, the

indicator light on the front of the LCD-TV changes from red to green. When the

LCD-TV is turned off using the power button, the LCD-TV will go into standby

mode and the indicator light turns red(or turns dark).

Audio Control

1.Press VOL+ button to increase the volume. A number will appear

on screen indicating the volume level.

2.Press VOL- button to decrease the volume. A number will appear

On screen indicating the volume level.

Mute

1.Press MUTE button to mute the sound temporarily. A mute icon

Appears on the screen.

2.Press MUTE button or VOL+ again to restore the sound.

The mute icon disappears.

Change the picture source so you can watch your TV, VCR, DVD, Cable ,

or any other devices that are connected to your TV.

1. Press INPUT button to enter the Select Source menu and then use

INPUT button to select the desired items TV, Video, S-Video, Component

DVD, PC, HDMI .

2. Press button to confirm . ENTER

Choose the input source

NOTE: The color of the indicator light may differ based upon the model purchased.

INFO

Press INFO button to display current program information.

Basic Operating Instructions

Select the TV Channel You Want

You can use the number buttons and button on the remote control to directly

select TV channels and press to confirm.

And you can press the buttons(CH+/CH-) on the remote control or on the panel to

make a selection.

ENTER

Picture Mode

Audio Mode

Press PICTURE button on the remote control for menu display . For desired mode

as follows:

Mild Standard Vivid Custom

Sleep

Press SLEEP button to set the time : Off

This function allows you to turn off the television after a pre-selected

minutes

-5 Min-10 Min-15 Min-30 Min- 45 Min

-60 Min-90 Min-120 Min-180 Min-240Min

number of

GUIDE(only available in digital signal)

Press GUIDE button in digital channels to display Guide menu.(This menu is

just for you to see the information and can not be changed)

Press CH+/CH- to select information for you to look over.

Off Concert Living Room Hall Bathroom Cave Arena Church

Press AUDIO button on the remote control for menu display . For desired mode

as follows:

ARC button

Press to select the aspect ratio among Normal, Wide, Zoom and Cinema.

(Display mode may differ from different inputs)

Basic Operating Instructions

button

Press to select additional channels (digital and analog) being broadcast by the

same station. For example, to select digital channel “11.1”, press “11”, then

press “ ” and “1”.

CH.LIST button

Press to display the channel list. Press VOL+/VOL- to turn to the next or previous

page, press CH+/CH- to select the item and Enter button to select the channel you

desired.

FAVORITE button

Adding favorite channels

Press FAVORITE under one channel. The favorite channel list opens.

Press CH+ or CH– to select a blank box, then press Enter to confirm .

The channel will be added to the favorites channel list.

Press Enter again, the channel will be removed from the favorites channel list.

Tuning to a favorite channel

Press FAVORITE. The favorite channel list opens.

Press CH+ or CH– to select the channel and press Enter to confirm .

Your LCD TV automatically tunes to the channel you selected.

Menu Operations

Video Menu Options

1. Press MENU button to display the main menu, and to select the main

menu function.

2. Press /ENTER button to enter the sub menu and to go up and down to

select the desired option .

3. Press /ENTER button to confirm and to make changes to the

parameters.

4. Press EXIT button to return to the main menu.

5. Press MENU button to exit the menu screen.

/

* In this manual, the OSD (On Screen Display) may be differ from your TV

These are examples to illustrate the TV's operation.

Press Input to select the input source. The menu for each source may be

different .

Picture quality can be adjusted for any input separately .

The picture quality on the screen can be adjusted as follows:

1. Press MENU button and until the following menu appears on the

screen.

2. Press /ENTER button to enter the menu function and to scroll up

and down to select the desired function.

3.Press /ENTER button to confirm and increase and decrease

the level to adjust the selected option to your preference .

4. Repeat step 2 and step 3 until desired picture quality has been achieved .

/

Note:

1.The options may be different because of the inputs.

2.Symbols on top of the menu in this manual may differ from the actual set display.

3.The picture options can be changed only in Custom mode, the other modes

are fixed.

Video

Audio

Channel

Lock

Function

Video

Mode Custom

Brightness

Contrast

Color

Tint

Sharpness

Color Temperature

Advanced Video

50

0

50

Select

BackAdjust

EXIT

ENTER

CH+/-

VOL+/-

Menu Operations

Function:

Mode: Select the type of picture which best corresponds to your viewing

requirements by selecting Picture Mode in Video menu. You may select the

picture mode directly by pressing the PICTURE button on the remote control.

Brightness :Press / button and /ENTER to confirm, then press to

adjust the brightness of the picture.

Contrast : Press / button and /ENTER to confirm, then press to

adjust the contrast of the picture.

Color : Press / button and /ENTER to confirm, then press to adjust

color saturation.

Tint : Adjust the tone of the picture .

Sharpness : Adjust the amount of the detail enhancement , the image

sharpness rises as the number increases (By increasing the level, it will show

cleaner and clearer images and by decreasing the level, it will make the picture

smoother).

Color Temperature: This will increase or decrease Warm (red) and Cool (blue)

colors to suit personal preferences.Select Cool to give the white colors a blue tint,

Standard to give the white colors a neutral tint, Warm to give the white colors

a red tint. Custom to allow you change the color manually.

Contrast, Brightness, Sharpness , Color Temperature and Tint can only be adjusted when

Mode in Custom mode.

Advanced Video:To adjust the picture in advanced level:

DNR: Digital Noise Reduction. To adjust to reduce the appearance of digitizing

error caused by the compression:Medium,Strong,Auto,Off and weak.

Black Level Extender: To adjust the ability in the black areas detail of the

picture:On and Off.

White Peak Limiter: To adjust the ability in the white areas detail of the

picture:On and Off.

CTI: Color Transient Intensity.To adjust the picture for color errors:Medium,Strong,

Off and weak.

Flesh Tone:To adjust the flash colors:On and Off.

Adaptive Luma Control: To adjust changes in the luminance of the picture:On and Off

/

Video Menu Options continued

Page is loading ...

Haier HL22K1 User manual

This manual is also suitable for

Haier HL22K1 User manual

Related papers

Other documents