Antec Quiet Computing Two Hundred User manual

Brand: Antec

Model: Quiet Computing Two Hundred

Category: Computer cases

Type: User manual

This manual is also suitable for

TWO HUNDRED

Antec Quiet Computing Two Hundred is a mid-tower gaming case with ample cooling options, supporting up to six 120mm fans and featuring a top 140mm TwoCool™ fan. It has 10 drive bays, including a front-loaded hot-swap SATA hard drive caddy for easy drive access. The case supports Mini-ITX, microATX, and Standard ATX motherboards and includes front panel USB 2.0 and AC'97 / HD audio ports.

TWO HUNDRED

SER

’

ANUAL

ABLE OF

ONTENTS

NTRODUCTION

1.1 Case Specifications.…..………………………………………………………………………………….. 3

1.2 Diagram…………………………………………………………………….…………………………………. 3

ARDWARE

NSTALLATION

UIDE

2.1 Setting Up….…………………………………………………………………………………………………. 4

2.2 Power Supply Installation……………………………………………………………………………… 4

2.3 Cable Management………………………………………………………………………………………. 5

2.4 Motherboard Installation..……………………………………………………………………………. 5

2.5 Internal 3.5” Device Installation……………………………………………………………………. 6

2.6 Front-Loaded Hot Swap SATA Hard Drive Caddy…………………………………………… 6

2.7 External 5.25” Device Installation…………………………………………………………………. 6

ONNECTING THE

RONT

I/O

ORTS

3.1 USB 2.0 Ports………………………………………………….……………………………………………. 7

3.2 AC’97 / HD Audio Ports……………………….……………………………………………………….. 7

3.3 Switch and LED Connectors…………………………………………………………………………… 8

3.4 Rewiring Motherboard Header Connections………………………………………………… 8

OOLING

YSTEM

4.1 TwoCool™ Fans ……………………………………………………………………………………………. 9

4.2 Optional Fans.………………………………………………………………………………………………. 10

4.3 Washable Air Filters………………………………………..……………………………………………. 11

UNDRED

SER

’

ANUAL

At Antec, we continually refine and improve our products to ensure the highest quality. It’s possible that

your new case will differ slightly from the descriptions in this manual. This isn’t a problem; it’s simply an

improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are

correct.

Disclaimer

This manual is intended only as a guide for Antec’s computer enclosures. For more comprehensive

instructions on installing the motherboard and peripherals, please refer to the user’s manuals that come

with those components.

The Two Hundred does not come with a power supply unit (PSU). Make sure you choose a power supply

that is compatible with your computer components and has a long enough power harness to reach your

motherboard and peripheral devices. We recommend our TruePower or Earthwatts power supplies for

the latest ATX specification compliance, broad compatibility, and energy-saving capability.

Although care has been taken to prevent sharp edges in your Antec case, we strongly recommend taking

the appropriate time and care when working with it. Avoid hurried or careless motions. Please use

reasonable precaution.

This manual is not designed to cover CPU, RAM, or expansion card installation. Please consult the

motherboard manual for specific mounting instructions and troubleshooting. Before proceeding, check

the manual for your CPU cooler to find out if there are steps you must take before installing the

motherboard. While installing hardware, keep your case on a flat, stable surface.

1.1 C

ASE

PECIFICATIONS

Case T

ype

Gaming Mid Tower

Color

Black

Dimensions

450mm (H) x 200mm (W) x 470mm (D)

17.7” (H) x 7.9” (W) x 18.5” (D)

Weight

13.9 lbs / 6.3 kg

Cooling

1 x Rear 120mm T

Cool

™

1 x Top special 140mm TwoCool™ fan

2 x Front 120mm fan mounts (optional)

1 x Side 120mm fan mount (optional)

Drive Bays

10 Drive Bays:

- 3 x External 5.25” drive bays

- 1 x External front-loaded hot swap 3.5” SATA hard drive caddy

- 6 x Internal 3.5” drive bays

Expansion Slots 7

Motherboard Size

Mini-ITX, microATX, Standard ATX

Front I/

O Panel

2 x USB 2.0

AC’97 / HD Audio In and Out

1.2

IAGRAM

1. 120mm rear TwoCool™ fan

2. 140mm top TwoCool™ fan

3. 120mm front fans (optional)

4. Washable air filters

5. Motherboard mount

6. Power supply mount

7. 5.25” drive bays

8. 3.5” drive bays

9. 3.5” hot-swap SATA drive bay

10. CPU cutout

11. Front I/O panel

ARDWARE

NSTALLATION

UIDE

2.1

ETTING

1. Place the case upright on a flat, stable surface with the

rear of the case facing you.

2. Remove the side panels by first removing the

thumbscrews at the rear of the case. Then, grip each

panel at the top and bottom and slide it toward the rear

of the case until it detaches from the chassis.

3. To remove the front bezel, locate the three plastic tabs

on the left side of the bezel. They fasten the front bezel

to the metal chassis. Release the tabs from the top down

to release the bezel. Swing the bezel open to about 45°

and gently lift the bezel upward, and it will come off

easily. Set the bezel in a safe place.

Note: Do not use your fingernails to pry or lift the panels.

2.2

OWER

UPPLY

NSTALLATION

1. With the case upright, place the power supply on the

bottom of the case.

Note: Power supplies with fans on the bottom of the

power supply will need to be mounted so that the

fan is facing the top of the case. The Two Hundred

provides mounting holes for power supplies with

standard mounting layouts to be installed upside

up or upside down.

2. Push the power supply to the back of the case and align

the mounting holes.

3. Attach the power supply to the case with the screws

provided.

2.3

ABLE

ANAGEMENT

There is a cable management compartment behind the 3.5” drive cage.

You can tuck or route excess cables in this compartment.

1. Open the right side panel as described in section 2.1.

2. Locate the cable management compartment with cable ties located

behind the walls of the 3.5” drive cage.

3. Tuck or route your excess cables to the compartment. This will keep

the cables from interfering with airflow in your case and help with

cooling.

4. Use the cable ties provided to hold them in place.

2.4

OTHERBOARD

NSTALLATION

1. Lay the case down, with the open side facing up.

The drive cages and power supply should be visible.

2. Make sure you have the correct I/O panel for your

motherboard. If the panel provided with the case

isn’t suitable, please contact your motherboard

manufacturer for the correct I/O panel.

3. Align your motherboard with the standoff holes and

remember which holes are lined up. Not all

motherboards will match with all the provided

holes; this is normal and won’t affect its

functionality.

4. Remove your motherboard by lifting it up.

5. Install standoffs as needed and put the

motherboard back in.

6. Screw in your motherboard to the standoffs with

the provided Phillips-head screws.

Note: The Two Hundred comes with a CPU cutout on the motherboard tray, which will allow you to

change your CPU heatsink without removing the motherboard.

2.5

NTERNAL

3.5”

EVICE

NSTALLATION

The Two Hundred provides space for up to six 3.5” hard

drives. Before you begin, remove the side panels and

front bezel of the case as described in section 2.1. Behind

the front bezel there is a fan cage which provides space

for up to two fans at the front of the case.

1. Open the fan cage by pressing both clips to release

it, then swing it open and detach it from the chassis.

2. Insert your 3.5” device into the 3.5” drive cage from

the front of the case until the mounting holes align

with the screw holes in the cage.

3. Fasten the device in place with the provided screws.

4. Mount any other 3.5” HDD devices accordingly.

5. Connect the appropriate power and data cables to

the device(s).

6. Replace the fan cage.

2.6 F

RONT

-L

OADED

WAP

SATA

ARD

RIVE

ADDY

This case comes with a built-in, externally accessible 3.5” SATA

drive bay where you can load/unload your drive without shutting

down your computer.

Note: Before you can use the hot swap feature, you must

install all related drivers that come with your

motherboard and turn on the “AHCI” function in the

BIOS to activate the hot swap feature.

Loading:

1. Align your SATA HDD with the drive bay with the connector

facing the case.

2. Push the HDD all the way into the bay until it locks into

position.

Unloading:

1. Ensure that your HDD is not in use.

Push the release button on the left-hand side of the drive bay

and pull the HDD free.

Signal

Names

Signal

Names

USB

Power

USB

Power

Negative

Signal

Negative

Signal

Positive

Signal

Positive

Signal

Ground

Key

(No

Connection)

Empty

Signal

Names

(HDA)

Signal

Names

(AC’97)

MIC2

MIC

AGND

GND

MIC2

MIC

Power

AVCC

FRO-R

Line

Out

(R)

MIC2_JD

Line

Out

(R)

F_IO_SEN

Key

(no

pin)

Key

(no

pin)

FRO-L

Line

Out

(L)

LINE2_JD

Line

Out

(L)

2.7

XTERNAL

5.25”

EVICE

NSTALLATION

There are three externally accessible 5.25” drive bays. Before you begin,

remove both side panels and front bezel as detailed in section 2.1.

1. Remove the drive bay faceplate by applying pressure to the inside

of the plate until it pops free of the bezel.

2. Slide your 5.25” device into the bay from the front of the case.

3. Secure the drive into position in the drive cage using the provided

screws.

4. Mount any other 5.25” devices accordingly.

5. Connect the appropriate power and data cables to your device(s).

ONNECTING THE

RONT

I/O

ORTS

3.1

USB

2.0

Connect the front I/O panel USB cable to the USB header pin on your motherboard. Check the

motherboard user’s manual to ensure that it matches the table below:

3.2

AC’97

UDIO

ORTS

There is an Intel® standard 10-pin AC’97 connector and an Intel® 10-pin HDA (High Definition Audio)

connector linked to the front panel of the case.

1 2

9 10

You can connect either the AC’97 or the HDA connector, depending on your motherboard. Locate the

internal audio connectors from your motherboard or sound card and connect the corresponding audio

cable. Consult your motherboard or sound card manual for the pin-out positions. Even if your system

supports both standards, only use one connector.

3.3

OWER

WITCH

ESET

WITCH

ARD

ISK

RIVE

LED

ONNECTORS

Connected to your front panel are LED and switch leads for power, reset, and

HDD LED activity. Attach these to the corresponding connectors on your

motherboard. Consult your motherboard manual for specific pin header

locations. For LEDs, colored wires are positive ( + ). White or black wires are

negative ( – ). If the LED does not light up when the system is powered on, try

reversing the connection. For more information on connecting LEDs to your

motherboard, see your motherboard user’s manual.

Note: Polarity (positive and negative) does not matter for switches.

3.4

EWIRING

OTHERBOARD

EADER

ONNECTIONS

There may come a time when you need to reconfigure the pin-out of a motherboard header connector.

Examples could be for your USB header, audio input header, or some other front panel connector such

as the Power Button connector.

Before performing any work, please refer to your motherboard user’s manual or your motherboard

manufacturer's website to be sure of the pin-out needed for your connector. We strongly recommend

making a notated drawing before beginning work so that you can recover if your work gets disturbed.

1. Determine which wires you need to remove in order to rewire your

plug to match the USB pin-outs on your motherboard (refer to your

motherboard user’s manual). Working on one connector at a time,

use a very small flathead screwdriver or similar tool to lift up on

the black tab located beside the gold posts (squares). This will

allow you to easily slide out the pins from the USB plug.

2. Working carefully so as not to damage the wires, connectors, or

pins, slowly remove the pin from the connector. Repeat these

steps for each wire you need to change.

3. Working carefully so as not to damage the wires, connectors or

pins, slowly reinsert the pin into the correct slot of the connector

then snap closed the black tab that was lifted in step 1. Repeat

these steps for each wire you need to change.

OOLING

YSTEM

4.1

OOL

™

ANS

Rear TwoCool™ Fan – There

120

25mm

TwoCool™

fan

preinstalled

the

rear

the

case.

The

fan

installed

the

air

will

blown

out

the

case. This

fan

comes

with

two-speed

switch

that

let

you

choose

the

speed

best

suited

your

need. The

default

fan

speed

setting

Low.

120mm TwoCool™ Specifications

Size

120 x 25mm TwoCool™ fan

Rated Voltage

12V

Operating Voltage

10.8V ~ 13.2 V

Speed

(RPM)

Input

Current

Airflow

Static

Pressure

Acoustic

Noise

Input

Power

High

1500

0.30A

(Max.)

1.434 m³ / min

(51.2 CFM)

1.212mm-H

(0.047 inch-H

27.9 dBA 3.6W

Low

900

0.18A

0.0843 m³ / min

(30.1 CFM)

0.486mm-H2O

(0.02 inch-H2O)

16.9 dBA 2.16W

Top TwoCool™ Fan

– The

case

comes

with

140

top

exhaust

fan.

The

fan

installed

the

air

will

blown out

the

case. This

fan

comes

with

two-speed

switch

that

let

you

choose

the

speed

best

suited

your

need. The

default

fan

speed

setting

Low.

140mm TwoCool™ Specifications

Size: 140 x 25mm TwoCool™

Rated Voltage: 12V

Operating Voltage:

10.8V ~ 13.2 V

Speed

(RPM)

Input

Current

Airflow

Static

Pressure

Acoustic

Noise

Input

Power

High

1200

0.30A

(Max.)

1.7 m³ / min

(58.9 CFM)

0.8 mm-H2O

(0.03 inch-H2O)

26 dBA 3.6W

Low

800

0.2A

0.95 m³ / min

(33.6 CFM)

0.28mm-H2O

(0.011 inch-H2O)

21.8 dBA 2.4W

Note

: The minimum voltage to start a typical TwoCool™ fan is 5V. We recommend that you set the

fan speed to High if you choose to connect the fan(s) to a fan control device or to the Fan-

Only connector found on some Antec power supplies. A fan control device regulates the fan

speed by varying the voltage, which may start as low as 4.5V to 5V. Connecting a TwoCool™

fan set on Low to a fan-control device may result in the fan not being able to start because

the already lowered voltage from the fan control device will be further reduced by the

TwoCool™ circuitry below 5V.

4.2 O

PTIONAL

ANS

There are total of three optional 120mm fan mounts—one side intake fan (on the left side panel) and

two front intake fans (at the front of the HDD cage). We recommend using Antec 120mm speed control

fans and setting the speed to Low. These fans must be installed so that the air is blowing into the case.

Side Fan

– The side fan enhances graphic cards cooling. The fan should be installed so air is blowing into

the case.

Front Fans

– You can install two 120mm fans to the fan cages in

front of the hard drive bays. To install the front fans:

Remove the front bezel as described in section 2.1.

Depress the two tabs on the left side of the black fan

holder and swing it outward. The holder will easily pull

free of the chassis.

Secure your 120mm fan(s) to the fan holder with the

provided screws. The fan should be installed so that air is

blowing into the case.

Reattach the fan holder to the case by inserting the right

side into the corresponding slots on the front of the case,

then rotating the holder back into position until it clicks

into place.

Note

: In order to build a quieter system, we recommend NOT installing the optional fans unless it is

necessary for cooling. If you choose to install them we recommend using Antec 120mm

TriCool™ fans and setting the speed to Low.

4.3 W

ASHABLE

ILTERS

Occasionally, it will be necessary to wash the air filters. Not washing the filters may result in high system

temperatures and possible stability problems. We recommend checking the air filters at least once a

month initially. The frequency will change depending on environmental conditions and system usage.

Users who run their systems 24/7 will have to check their filters more often than those who don’t run

their systems every day.

Front Air Filter

– There is an air filter located behind the

front bezel.

To remove the filter

Remove the front bezel as listed in section 2.1.

Remove the screw in the center of the front

bezel to release the air filter.

Antec, Inc.

47900 Fremont Blvd.

Fremont, CA 94538

USA

tel: 510-770-1200

fax: 510-770-1288

Antec Europe B.V.

Stuttgartstraat 12

3047 AS Rotterdam

Netherlands

tel: +31 (0) 10 462-2060

fax: +31 (0) 10 437-1752

Customer Support: US & Canada

1-800-22ANTEC

custome[email protected]

Europe

+31 (0) 10 462-2060

europe.tec[email protected]

www.antec.com

All trademarks are the property of their respective owners. Reproduction in whole or in part without

written permission is prohibited.

Antec Quiet Computing Two Hundred User manual

Brand: Antec

Model: Quiet Computing Two Hundred

Category: Computer cases

Type: User manual

This manual is also suitable for

TWO HUNDRED

Download PDF

report

Antec Quiet Computing Two Hundred User manual

This manual is also suitable for

Antec Quiet Computing Two Hundred User manual

Related papers

Other documents