Uniden TRU8885-2 User manual

TRU 8885

SERIES

OWNER'S

MANUAL

[1]

www.uniden.com

Contents

WELCOME/FEATURES 2

TERMINOLOGY 3

CONTROLS & FUNCTIONS 4

DISPLAY AND ICONS 6

SOFT KEY FUNCTION 8

GETTING STARTED 9

Setting up the Phone 9

Mounting the Base Unit on a Wall 13

Main Menu Options 15

Setting Menu Options 16

BASICS 33

Making and Receiving Calls 33

Flash and Call Waiting 34

Placing a Call on Hold 34

Redialing a Call 35

Adjusting the Earpiece and Speaker Volume 37

Do Not Disturb (DND) 37

Mute Microphone 38

Tone Dialing Switch-over 39

Traveling Out of Range 39

Privacy Mode 40

3 or 4-Way Conferencing 40

PHONEBOOK 42

Phonebook (Storing Phone Numbers, Names,

Distinctive Rings and Speed Dial) 42

Chain Dialing 43

Steps for Entering Names and Special Characters 44

Viewing the Phonebook 46

Making Calls Using the Phonebook 47

Speed Dialing 47

Editing or Erasing a Phonebook Entry 48

Copying Phonebook Entries 49

CALLER ID 50

Caller ID and CIDCW (Caller ID on Call Waiting) 50

Viewing the Caller ID List 51

Deleting a Caller ID Message 52

Using the Caller ID Message List 53

Call Waiting Deluxe Features 55

THE INTEGRATED ANSWERING DEVICE 56

The Integrated Telephone Answering Device 56

Turning the Answering System On/Off 57

Setting your outgoing message (Greeting) 57

Using the Answering Setup Menu 58

New Message LED 58

Using your Answering System 59

Remote Operation 63

EXPANDING YOUR PHONE 67

Expanding Your Phone 67

Connecting the Charger 68

Register the Handset 68

Using DirectLink Mode 70

Intercom/Call Transfer Feature 71

ADDITIONAL INFORMATION 74

Changing the Digital Security Code 74

Find Handset 74

Installing the Beltclip 75

Headset Installation 75

Note on Power Sources 76

Maintenance 76

General Information 77

TROUBLESHOOTING 78

Troubleshooting 78

Liquid Damage 81

PRECAUTIONS & WARRANTY 82

I.C. NOTICE 84

MEMORY LIST 85

INDEX 86

REMOTE OPERATION CARD 88

MAIN MENU FLOW CHART 90

WELCOME/FEATURES [2]

www.uniden.com

Congratulations on your purchase of the Uniden Multi-Handset Cordless System

telephone. This unit is different from conventional cordless telephones. When the base

unit is connected to AC power and a telephone line, it can support up to 10 handsets.

You can now place a fully-featured cordless handset anywhere in your home or office

where AC power is available to connect the handset chargers. Extra handsets also allow

you to establish a 4-way conference call among 2 handsets, the base speakerphone, and

an outside line.

Note: Some illustrations in this manual may differ from the actual unit for explanation

purposes.

As an Energy Star

®

Partner, Uniden has determined that this product or product

models meets the Energy Star

®

guidelines for energy efficiency.

Energy Star

®

is a U.S. registered mark.

• 5.8GHz Digital Expandable

• Integrated Answering Device

• Dual Keypad with LCD Screen at Base

• 10 Multi-Handset Expandability

• Hands-Free Speakerphone in the Handset and Base

• Caller ID/Caller ID on Call Waiting (subscribe through local telephone company)

• Call Waiting Deluxe (subscribe through local telephone company)

• 100 Programmable Memory Locations

• Trilingual Display Options and Voice Prompts (English, French and Spanish)

• Intercom/Call Transfer Between Handsets

• 20 Distinctive Ring Options (10 ringer tones and 10 melody ringers)

• Mute and Hold Features

• Do Not Disturb (DND) Feature

• DirectLink™ Mode

• Room/Baby Monitoring

• Battery Level Indicator

• Clock Display

•Animation Displays

WELCOME/FEATURES

Welcome

Features

[3] TERMINOLOGY

www.uniden.com

This series features AutoTalk™ and AutoStandby™. AutoTalk allows you to answer a call by just removing

the handset from the cradle so you don't have to waste time pushing buttons. AutoStandby allows you to

hang up by simply returning the handset to the cradle.

To protect you against mis-billed calls that might result from your phone being activated by other

equipment, this series has

Random Code™ digital security, which automatically selects one of over

approx. 65,000 digital security codes for the handset and base.

Digital Spread Spectrum Technology uses a wider frequency band than standard digital transmissions. The

result is a more secure conversation with the clarity of digital sound, extended range, and minimal

interference from other cordless phones.

IntegriSound™ Built in sound quality which provides life-like conversations.

With DirectLink™ mode, you can use 2 or more handsets as radio transceivers (walkie-talkies).

Be sure to visit our web site: www.uniden.com

Uniden

®

is a registered trademark of Uniden America Corporation.

AutoTalk, AutoStandby, DirectLink, IntegriSound and Random Code are trademarks of Uniden America.

Terminology

•Standby Mode - The handset is not in use, and talk/flash or speaker has not been pressed. No dial tone is

present.

•Talk Mode - The handset is not in the cradle, and talk/flash or speaker has been pressed, enabling a dial tone.

Talk

appears on the display.

TERMINOLOGY

CONTROLS & FUNCTIONS [4]

www.uniden.com

Controls & Functions

1. Handset Antenna

2. Beltclip Hole

3. Speakerphone Speaker and Ringer

4. Handset Battery Compartment

5. New Message LED

6. Handset Earpiece

7. LCD Display

8. soft Keys (P. 8)

9. cid/vol/ (volume up) (P. 37 & 16)

10.redial/p/vol/ (volume down) (P. 35, 33, 16 & 37)

11.

*

/tone/< (P. 39 & 44)

12.speaker (P. 33)

13.intcom/hold (P. 71 & 34)

14.Headset Jack Cover

15.talk/flash (P. 33 & 34)

16.end (P. 33)

17.phonebook (P. 42)

18.#/> (P. 44)

19. (Message) (P. 65)

20.Handset Microphone

21.Handset Charging Contacts

2

1

4

3

5

6

7

8

9

10

11

12

13

20

21

15

18

19

16

17

14

Play

Skip

Stop

Delete

Repeat

Retrieve TAD message

with Handset Remote keys

CONTROLS &

FUNCTIONS

[5] CONTROLS & FUNCTIONS

www.uniden.com

25

26

24

33

34

3130292827

40 4122 23 32

36

37

38

39

35

22. In use LED

23. play/stop (P. 59)

24. cid/exit (P. 51)

25. Charge LED

26. Base Charging Contacts

27. delete message (P. 60)

28. mic (microphone)

29. answer on/off (P. 57)

30. do not disturb (P. 37)/DND LED

31. /tone (P. 39)

32. Message Counter Display

33. soft Keys (P. 8)

34. Base Speaker

35. speaker/speaker LED (P. 33)

36.

phonebook

(P. 42)

37.

intercom

/

hold

(P. 71

&

34)

38.

flash

/

find hs

Key (P. 34

&

74)

39.

/volume/ /

(volume up/down)

(P. 37 & 16)

40. DC IN 9V Jack

41. TEL LINE Jack

CONTROLS &

FUNCTIONS

DISPLAY AND ICONS [6]

www.uniden.com

Display and Icons

Example of the standby mode display

•Handset

•Base

* appears if you have a new message.

appears if you turn your answering system off.

** appears when the message storage is full.

appears if you set your answering system to announce only.

ICON Appears During DESCRIPTION

Standby/Talk

Battery icons indicate the handset battery status. This icon changes depending on

the battery status (empty, low, medium and full).

Standby The Ringer off icon indicates that ringer is turned off.

Talk The Mute icon appears when you mute the handset or base.

Talk The Speaker icon appears when the handset speaker phone is used (handset only).

Talk The Privacy icon appears when the Privacy Mode is turned on.

Talk The Recording icon appears while recording a conversation.

570#

*CPFUGV

0GY%+&

/'07

Ringer off icon (when the ringer is off)/ day of the week and time / battery icon

Handset ID and Banner

Number of new Caller ID calls received (If there are no new Caller ID messages,

the Handset ID appears here.)

* Status of your

Answering machine

** Number of message

Day of the week and time

Number of new Caller ID calls received

0'9

1((

#059'4

(7..

#PPQWPEG

10.;

DISPLAY AND ICONS

[7] DISPLAY AND ICONS

www.uniden.com

Animation Displays (Handset only)

The handsets have a variety of animation displays. Below are examples of the animation screens and

what they mean:

Turning on the phone Hanging up the phone Confirmation (Done!) Deleting (Deleted!)

Making a call Find Handset/Paging the Handset

Also, the animation display changes depending on the ringer volume setting.

Out of Range Unavailable Low Battery

9GNEQOG

2NGCUG9CKV



'PF

/'07

&QPG

&GNGVGF

6CNM



/76' /'07

2CIKPI

4KPIGT8QNWOG

$#%- 1- $#%- 1-

4KPIGT8QNWOG

?

$#%- 1-

4KPIGT8QNWOG

1WV1H4CPIG

/'07

7PCXCKNCDNG

/'07

.QY$CVVGT[

DISPLAY AND ICONS

SOFT KEY FUNCTION [8]

www.uniden.com

Soft Key Function

"Soft" keys are keys that change function during the operation of the phone. There are three soft keys on

the base and three on each handset.

The function of each soft key is determined by the icon that appears directly above it. For example, when

the base is in standby mode, pressing soft key 1 will redial the last number. When the base is in talk

mode, pressing soft key 1 will mute the microphone.

Complete information on the features controlled by the soft keys can be found under each feature.

In standby mode

Handset Base

In talk mode

Handset Base

570#

*CPFUGV

0GY%+&

/'07

Soft key 2

570#

0GY%+&

4'&+#. /'07 4'%14&

Soft key 1 Soft key 2 Soft key 3

6CNM



/76' /'07

522JQPG

/76'

/'07



Soft key 1 Soft key 3

Soft key 1 Soft key 2

SOFT KEY FUNCTION

[9] GETTING STARTED

www.uniden.com

Setting up the Phone

A. Choose the best location

When choosing a location for your new phone, here are some important guidelines

you should consider:

• The location should be close to both a phone jack and a continuous power outlet (one

which is not connected to a switch).

• The base and handset should be kept away from sources of electrical noise such as motors,

microwave ovens, and fluorescent lighting.

• For better reception, place the base as high as possible.

• The base should be placed in an open area for optimum range and reception.

• If your home has specially wired alarm equipment connected to phone line, be sure that

installing the system does not disable your alarm equipment. If you have questions about

what will disable alarm equipment, contact your telephone company or a qualified

installer.

For maximum range:

•Keep the antenna free

of obstruction.

•When the handset is

not in use place the

handset in an upright

position.

•Do not hold the

handset where you

would block the signal.

•Metal and reinforced

concrete may affect

cordless telephone

performance.

note

Correct

Incorrect

GETTING STARTED

GETTING STARTED [10]

www.uniden.com

B. Install the rechargeable battery pack into the handset, and

charge for at least 15-20 hours before using!

The handset is powered by a rechargeable battery pack. The battery recharges

automatically when the handset is placed in the base unit. To maximize the charge

capacity of your battery pack, DO NOT plug the telephone cord into the base unit

and wall jack until the battery is fully charged.

1) Press down on the handset battery case cover (use the

finger indention for a better grip) and slide the cover

downward to remove.

2) Turn the battery pack so that the connector with the red

and black wires is near the jack inside the battery

compartment. Match the connector's wire colors to the

polarity label in the battery compartment (the connector

notches fit into the grooves of the jack only one way).

Push the battery pack connector into the jack until it

clicks into place.

3) Make sure you have a good connection by gently pulling on

the battery wires. If the connection is secure, the battery

jack will remain in place.

4) Place the battery case cover back on the handset and slide

it upwards until it clicks into place.

5) Place the handset in the base unit for 15-20 hours without

interruption. The base unit's LED light (labeled charge)

illuminates once the handset is placed in the base. The

LED light will illuminate whether the battery pack is

connected or not.

The battery may be

purchased by calling

Uniden's Parts

Department (see back

cover page).

note

GETTING STARTED

[11] GETTING STARTED

www.uniden.com

Low battery alert

When the battery pack is very low, the phone is programmed to eliminate functions

in order to save power.

The battery pack needs to be charged when:

- The empty battery icon appears.

-

Low Battery

appears in the display.

If the phone is in standby mode, none of keys will

operate. If you are on a call, complete your conversation as quickly as possible, and

return the handset to the cradle.

Cleaning the battery charging contacts

To maintain a good charge, it is important to clean the

charging contacts on both the handset and the base

unit once a month. Using water only, dampen a cloth

to clean the charging contacts. Then make sure to go

back over the charging contacts with a dry cloth

before returning the handset to the base to charge.

Caution: Do not use paint thinner, benzene, alcohol,

or other chemical products. Doing so may discolor the

surface of the telephone and damage the finish.

.QY$CVVGT[

contacts

Even when the battery

pack is not being used,

it will gradually

discharge over a long

period of time.

For optimum performance,

be sure to return the

handset to the base unit

after each telephone call.

note

GETTING STARTED

GETTING STARTED [12]

www.uniden.com

C. Connect the base unit

1) Connect the AC adapter to the DC IN 9V jack and to a

standard 120V AC wall outlet.

Connect the AC adapter to a continuous power supply

(i.e., an outlet that is not controlled by a switch).

2) Set the base on a desk or tabletop, and place the

handset in the base unit.

Place the base unit close to the AC outlet so that

you can unplug the AC adapter easily.

3) Make sure that the charge LED illuminates.

If the LED does not illuminate, check to see that the

AC adapter is plugged in and the handset makes

good contact with the base charging contacts.

After installing the battery pack in the handset,

charge your handset for at least 15-20 hours before

plugging into the phone line.

4) Once the handset battery pack is fully charged,

connect the telephone line cord to the TEL LINE jack

and to a telephone outlet.

If your telephone outlet isn't modular, contact

your telephone company for assistance.

•Use only the supplied

[AD-830] AC adapter.

Do not use any other

AC adapter.

•Place the power cord

so that it does not

create a trip hazard or

where it could become

chafed and create a

fire or electrical

hazard.

note

GETTING STARTED

[13] GETTING STARTED

www.uniden.com

Mounting the Base Unit on a Wall

Standard wall plate mounting

This phone can be mounted on any standard wall plate.

1) Make the AC adapter and the telephone line cord

through the hole on the wall mount adapter.

2) Plug the AC adapter into the DC IN 9V jack.

3) Plug the telephone line cord into the TEL LINE

jack.

4) Slide the wall mount adapter into the notches on

the base.

5) Plug the AC adapter into a standard 120V AC wall

outlet. Hook the cord on the notch of the wall

mount adapter.

6) Plug the telephone line cord into the telephone

outlet. Hook the cord on the notch of the wall

mount adapter.

7) Align the mounting slots on the base with the

mounting posts on the wall. Then push in and

down until the phone is firmly seated.

To remove, push up

a tab on the wall

mount adapter as

shown.

DO NOT use an AC outlet

controlled by a wall

switch.

!

GETTING STARTED

GETTING STARTED [14]

www.uniden.com

Direct wall mounting

If you don't have a standard wall plate, you can mount your phone directly to the

wall. Before doing this, consider the following:

• Avoid electrical cables, pipes, or other items behind the mounting location that could

cause a hazard when inserting screws into the wall.

• Try to mount your phone within 5 feet of a working phone jack to avoid excessive lengths.

• Make sure the wall material is capable of supporting the weight of the base and handset.

• Use #10 screws (minimum length of 1 & 3/8 inches) with anchoring devices suitable for

the wall material where the base unit will be placed.

1) Insert two mounting screws into the wall (with their

appropriate anchoring device), 3 & 15/16 inches

apart. Allow about 1/8 of an inch between the wall

and screw heads for mounting the phone.

2) Refer to steps 1 through 7 on page 13 to mount the

telephone.

GETTING STARTED

[15] GETTING STARTED

www.uniden.com

Main Menu Options

Your phone has seven main menu options: DirectLink Mode, Room Monitor,

Handset Setup, Base Setup, Answ. Setup, Global Setup and Deregister HS. You

can change Room Monitor, Answering Setup, and Global Setup settings from the

base or from any handset. DirectLink Mode, Handset Setup, and Deregister HS are

only available from a handset. Base Setup is only available from the base.

Default Settings

The default settings set from the factory match the features that most people use.

You may not need to change them. However, there are a number of options you

must set and entries you must make in memory to take full advantage of all the

phone features. The table below lists the default settings.

Function Handset Base Function Handset Base

Ringer Tone

Flicker

Day & Time

SUN 12:00 AM

Ringer Volume

High

CW / CWDX

CW on/CWDX off

Distinctive Ring

On -

Dial Mode

Tone

Auto Talk

Off -

Area Code

None -

Anykey Answer

Off -

Security Code

80

Banner

“ “ -

Record Time

1 minute

Language

English

Ring Time

Toll Saver

(LCD) Contrast

Level 5

Message Alert

Off

Key Touch Tone

On -

Call Screen

On

Animation Screen

On -

Room Monitor

(allow monitoring)

On -

• For Global Setup,

Answ. Setup, and

Deregister HS menu

options, make sure

the line is not in use

and the handsets are

within range of the

base.

•For a flow chart of

the main menu, see

page 90.

note

GETTING STARTED

GETTING STARTED [16]

www.uniden.com

Setting Menu Options

Entering the Menu

1) In standby mode, press the MENU soft key.

2) Use volume up/down to move the pointer to a desired

main menu (DirectLink Mode, Room Monitor, Handset

Setup, Base Setup, Answ. Setup, Global Setup, and

Deregister HS).

3) Press the OK soft key to select the desired main menu.

To return to the previous screen, press the BACK soft

key.

4) Use volume up/down to select a desired submenu and

then press the OK soft key to enter.

5) In the submenu option, use volume up/down to select

an item. Press the OK soft key to confirm your

selection. For detailed instructions, see the following

sections for the desired submenu option. To return to

the previous screen, press the BACK soft key.

6) To exit the menu, press end on the handset or cid/exit on the base.

&KTGEV.KPM/QFG

4QQO/QPKVQT

*CPFUGV5GVWR

$#%- $#%- 1-

•Han

d

set

4QQO/QPKVQT

$CUG5GVWR

#PUY5GVWR

$#%- $#%- 1-

•Base

GETTING STARTED

[17] GETTING STARTED

www.uniden.com

DirectLink Mode (Handset only)

In DirectLink mode, a pair of handsets can function as two-way radios. DirectLink

Mode allows two handsets to communicate with each other without the base unit or

a telephone line. Use them at sporting events or while shopping to stay in contact

with family members or friends. You must set both handsets to DirectLink Mode

activate this feature.

Using DirectLink Mode

1) Enter the DirectLink Mode menu.

To enter DirectLink

mode press [ENTER]

appears.

2) Press the ENTER soft key to enter the DirectLink Mode.

You will hear a confirmation tone, and

DirectLink Mode

Complete

appears.

3) To return back to the normal mode, press the CANCEL

soft key and then the OK soft key, or return the handset

to the cradle.

6QGPVGT

&KTGEV.KPMOQFG

RTGUU='06'4?

$#%- $#%- '06'4

You must have at least

two handsets to use

DirectLink Mode.

note

GETTING STARTED

GETTING STARTED [18]

www.uniden.com

Room/Baby Monitor

This feature allows you to monitor

sounds in another room. Place the base

or a handset in the room you wish to

monitor; it will function as a

microphone. A second handset can be

set to function as a remote speaker,

allowing you to monitor sounds in the

room.

Using Room/Baby Monitor

1) Enter the Room Monitor menu (see

"Entering the Menu" on page 16).

Listen to;

appears.

2) Select the handset or base you want

to monitor by using volume up/

down.

3) Press the OK soft key.

Monitoring

appears, and you hear sounds in the room

where the handset or the base is installed.

4) To turn off the Room Monitor, press the END soft key,

or end.

If you want to prevent other handsets or the base from monitoring this handset,

press the MENU soft key. Select the Handset Setup menu, and then the Room

Monitor submenu. Select

Off

and press the OK soft key.

Monitor using

handset or

base unit

/QPKVQTKPI

㨭㨭

*CPFUGV

'0&

GETTING STARTED

[19] GETTING STARTED

www.uniden.com

Handset Setup / Base Setup

The following submenu options must be set separately for each handset and the

base.

Selecting a Ringer Volume

Ringer volume lets you choose from one of three ringer volumes.

From the handset

1) Press the MENU soft key. Select the Handset Setup menu, and then the Ringer

Volume submenu.

2) Press volume up/down to select

HIGH

,

LOW

, or

OFF

.

3) Press the OK soft key. You will hear a confirmation tone.

From the base

In standby mode, press volume up/down to select one of three ringer volumes (Off,

Low, or High).

Selecting a Ringer Tone (Handset only)

Ringer tone lets you choose from 10 ringer tones or 10 melodies:

- Ringers (Flicker, Clatter, Soft Alert, Wake Up, Light Bug, Beep Boop, Tone Board,

Chip Chop, Party Clap, Reminder)

- Melodies (Beethoven's Symphony #9 [Beethoven9], For Elise [Elise], We Wish You A Merry

Christmas [Merry- Xmas], Home Sweet Home [Hm Swt Hm], Lorri Song #6 [Lorri Song],

When the Irish Eyes Are Smiling [Irish Eyes], Aura Lee, Let Me Call You Sweet Heart

[Sweetheart], Star Spangled Banner [Star Spngl], Old MacDonald [Old MacDld])

GETTING STARTED

Page is loading ...

Uniden TRU8885-2 User manual

This manual is also suitable for

Uniden TRU8885-2 User manual

Related papers

Other documents