Navigon 5100 MAX User manual

User's manual

NAVIGON 5100 | 5110

English (UK)

June 2007

This symbol showing a crossed-through refuse container signifies that,

within the European Union, the product must be disposed of as sorted

waste. This applies both to the product itself, as well as to all

accessories that carry this symbol. This product may not be disposed

of with unsorted household waste.

Imprint

NAVIGON AG

Schottmüllerstraße 20A

D-20251 Hamburg

The information contained herein may be changed at any time without prior

notification. This manual nor any parts thereof may not be reproduced for any

purpose whatsoever without the express written consent of NAVIGON AG, nor

transmitted in any form either electronically or mechanically, including photocopying

and recording. All technical specifications, drawings etc are subject to copyright law.

User's manual NAVIGON 5100 | 5110

User's manual Table of Contents  III

Table of Contents

1 Introduction.......................................................................................6

1.1 About this manual.....................................................................................6

1.1.1 Conventions ...............................................................................6

1.1.2 Symbols......................................................................................6

1.2 Legal notice ..............................................................................................6

1.2.1 Liability .......................................................................................6

1.2.2 Trademarks ................................................................................6

1.3 Customer Service.....................................................................................7

2 Before you begin...............................................................................9

2.1 Scope of Delivery .....................................................................................9

2.2 Description of the NAVIGON 5100 | 5110..............................................10

2.3 Preparing NAVIGON 5100 | 5110 for use ..............................................10

2.3.1 Charging the rechargeable battery...........................................10

2.3.2 Inserting a memory card...........................................................11

2.3.3 Preparing the navigation system for use ..................................11

2.4 Navigation with GPS ..............................................................................12

2.5 Important safety information...................................................................13

2.5.1 Navigation safety information ...................................................13

2.5.2 Safety information for the navigation device ............................13

2.5.3 Safety guidelines when installing in your car............................14

3 Operating the navigation software................................................15

3.1 Volume .................................................................................................15

3.2 Information .............................................................................................15

3.3 Software keyboard .................................................................................17

3.4 Lists .................................................................................................17

3.5 Options .................................................................................................18

3.6 Menus .................................................................................................18

4 Password Lock................................................................................18

4.1 Activating password protection...............................................................18

4.2 Changing a password.............................................................................19

4.3 Cancelling password protection .............................................................19

4.4 Switching on NAVIGON 5100 | 5110 .....................................................19

User's manual NAVIGON 5100 | 5110

IV  Table of Contents User's manual

4.4.1 Forgotten your password?........................................................19

5 Navigation .......................................................................................20

5.1 Starting NAVIGON 5100 | 5110 .............................................................20

5.1.1 Initialising the GPS-receiver.....................................................21

5.2 Specifying a new destination..................................................................21

5.2.1 Specifying the destination country............................................22

5.2.2 Destination address..................................................................22

5.2.3 Special destinations .................................................................23

5.2.4 Quick access to special destinations........................................25

5.2.5 Information about the destination .............................................26

5.3 Selecting a saved destination.................................................................26

5.3.1 Last Destinations......................................................................26

5.3.2 Favourites.................................................................................27

5.4 Navigating homewards...........................................................................27

5.5 Determining destinations on the map.....................................................27

5.6 Starting navigation..................................................................................28

6 Managing Destinations...................................................................29

6.1 Saving a destination ...............................................................................29

6.2 Defining a destination as home address ................................................30

7 Routes with stages .........................................................................30

7.1 Route planning .......................................................................................30

7.1.1 Entering the starting point ........................................................30

7.1.2 Entering route points ................................................................31

7.1.3 Editing route points...................................................................31

7.2 Managing routes.....................................................................................32

7.2.1 Saving routes ...........................................................................32

7.2.2 Loading routes..........................................................................32

7.3 Navigation ..............................................................................................33

7.3.1 Calculating and displaying routes.............................................33

7.3.2 Simulating routes......................................................................33

7.3.3 Starting navigation....................................................................33

8 Options............................................................................................34

9 Working with the map.....................................................................37

9.1 Maps .................................................................................................37

9.2 Map in Preview mode.............................................................................37

User's manual NAVIGON 5100 | 5110

User's manual Table of Contents  V

9.3 Map in Navigation mode.........................................................................38

9.4 Reality View............................................................................................41

9.5 Map in Destination search mode............................................................41

9.5.1 Operating in Destination search mode .....................................43

10 Useful functions..............................................................................44

10.1 GPS status, storing the current location.................................................44

10.2 Turn-by-Turn List....................................................................................44

10.2.1 Blocking route sections ............................................................45

10.2.2 Removing blocks and using original routes..............................45

10.3 TMC (Traffic Information) .......................................................................45

10.3.1 Displaying traffic messages......................................................45

10.3.2 TMC Settings............................................................................46

10.4 Logbook .................................................................................................47

11 Configuring NAVIGON 5100 | 5110................................................47

12 Appendix .........................................................................................49

12.1 Technical data ........................................................................................49

12.2 Declaration of Conformity.......................................................................50

13 Index ................................................................................................51

User's manual NAVIGON 5100 | 5110

- 6 - Introduction

1 Introduction

1.1 About this manual

1.1.1 Conventions

For better legibility and clarification, the following styles are used in this

manual:

Bold and italics: Registered names, company and product descriptions.

S

MALL CAPITALS: Window and dialogue box titles.

Bold: Highlighting of important parts in the text.

Underlined

: Descriptions of buttons, input fields and other elements

on the user interface.

1.1.2 Symbols

The following symbols refer to specific passages of text:

Instructions and tips for operating the software

More detailed information and explanations

Warnings

1.2 Legal notice

1.2.1 Liability

The software and the manual are subject to change without notice.

NAVIGON AG is not liable for the accuracy of the information contained

in this manual or for damages resulting from the use of this manual.

We always appreciate any suggestions that will allow us to offer

improved performance of our products in the future, or information

regarding malfunction.

1.2.2 Trademarks

All brands and trademarks mentioned in this document are possibly

registered by third parties and are subject to the current legislation and

User's manual NAVIGON 5100 | 5110

Introduction - 7 -

to the rights of their respective owners without reservation. All

mentioned names of products, societies, or brands may be registered

trademarks of their respective owners. Every right that is not explicitly

accorded is reserved.

The absence of the explicit labelling of registered trademarks used in

this manual does not imply that the brand is not subject to the rights of a

third party.

► Windows and ActiveSync are trademarks of the Microsoft

Corporation.

► NAVIGON is a registered trademark of NAVIGON AG.

1.3 Customer Service

Our service team staff are available via telephone or E-mail in many

countries.

You can find additional information at the NAVIGON AG website under

(

www.navigon.com) in the "Service & Support" section.

Telephone Support

Note: All quoted costs refer to calls made from a land line within the

relevant country.

Germany

Telephone: 01805-6284466

Service times: Monday to Saturday from 8 a.m. to 8 p.m. CET

Costs: € 0.14/min.

Belgium

Telephone: 0900-70016

Service times: Monday to Friday from 8 a.m. to 8 p.m. CET

Costs: € 0.45/min. + € 0.05 per call

Denmark

Telephone: 901-31033

Service times: Monday to Friday from 8 a.m. to 8 p.m. CET

Costs: 3.00 DKK/min.

Finland

Telephone: 0600-413414

Service times: Monday to Friday from 9 a.m. to 9 p.m. hrs

(local time)

Costs: € 0.50/min.

User's manual NAVIGON 5100 | 5110

- 8 - Introduction

France

Telephone: 0891-650065

Service times: Monday to Saturday from 8 a.m. to 8 p.m. CET

Costs: € 0.225/min.

Great Britain

Telephone: 0905-8480701

Service times: Monday to Friday from 7 a.m. to 7 p.m.

(local time)

Costs: 0.25 GBP/min.

Italy

Telephone: 166-205301

Service times: Monday to Friday from 8 a.m. to 8 p.m. CET

Costs: € 0.40/min. + € 0.09 per call

Netherlands

Telephone: 0900-0400468

Service times: Monday to Friday from 8 a.m. to 8 p.m. CET

Costs: € 0.30/min. + € 0.045 per call

Norway

Telephone: 820-33050

Service times: Monday to Friday from 8 a.m. to 8 p.m. CET

Costs: 3.26 NOK/min.

Austria

Telephone: 0820-240437

Service times: Monday to Friday from 8 a.m. to 8 p.m. CET

Costs: € 0.145/min.

Sweden

Telephone: 0900-1001110

Service times: Monday to Friday from 8 a.m. to 8 p.m. CET

Costs: 4.00 SEK/min.

Switzerland

Telephone: 0848-662544

Service times: Monday to Friday from 8 a.m. to 8 p.m. CET

Costs: 8 a.m. - 5 p.m.: 0.11 CHF/min

5 p.m. - 10 p.m.: 0.09 CHF/min

10 p.m. - 8 a.m.: 0.06 CHF/min.

User's manual NAVIGON 5100 | 5110

Before you begin - 9 -

Spain

Telephone: 807-001205

Service times: Monday to Friday from 8 a.m. to 8 p.m. CET

Costs: 8 a.m. - 8 p.m.: € 0.356/min. + € 0.104 per call

8 p.m. - 8 a.m.: € 0.288/min. + € 0.104 per call

Other countries

Telephone: +49-221-2888-999

Service times: Monday to Friday from 8 a.m. to 8 p.m. CET

Costs: dependent on telephone provider

Support via E-mail

Danish: [email protected]

German:

English:

Finnish:

French:

Italian:

Dutch:

Norwegian:

Swedish:

Spanish:

2 Before you begin

2.1 Scope of Delivery

Please check that the contents of the delivery are complete. If the

contents are incomplete, please notify us within 14 days of

purchasing. The purchased product includes the following:

► NAVIGON 5100 | 5110 navigation device

► Car cradle

► Car charger cable ( 12V-adapter for the vehicles cigarette lighter)

► SD-card containing software and navigation maps

► Manual

► CD with manuals (PDF, including languages not printed)

► Pouch

User's manual NAVIGON 5100 | 5110

- 10 - Before you begin

2.2 Description of the NAVIGON 5100 | 5110

1

Touch screen

2

Mini-USB-socket for car charger cable

3

LED

4

Headset socket (also used to connect TMC-antenna)

5

Slot for SD-memory card

6

On/Off/Standby

7

Connection for external GPS-antenna

2.3 Preparing NAVIGON 5100 | 5110 for use

2.3.1 Charging the rechargeable battery

► Connect the car charger cable to the navigation device and to the

vehicle’s cigarette lighter. (see also "

Supplying power to the

navigation device", on page

12)

The LED of the NAVIGON 5100 | 5110 lights orange during charging.

The LED lights green when the NAVIGON 5100 | 5110 is fully charged.

User's manual NAVIGON 5100 | 5110

Before you begin - 11 -

Note: It takes approx. 4-5 hours to charge the device when the battery

is flat.

A fully charged battery enables 4 hours of use.

2.3.2 Inserting a memory card

► Insert the memory card provided into the device (see image). Press

the card into the device until it locks into place.

Removing the memory card

1. Switch the navigation device off by pressing the

(On/Off/Standby

) switch for at least 6 seconds.

2. Press the memory card gently into the device until the lock

disengages.

2.3.3 Preparing the navigation system for use

Caution! Please be sure to refer to the safety information in chapter

"

Important safety information" on page 13.

Securing the cradle

1. Clean that part of the windscreen to which you would like to secure

the cradle. The windscreen must be dry and free of dirt and grease.

2. Using the suction cup, fix the cradle provided to the windscreen.

The cradle should be as level as possible.

3. Press the lever on the suction cup down.

Securing the navigation device to the cradle

The navigation device is secured to the cradle by means of a bayonet

fitting. This connection functions in a similar way to attaching a lens to a

camera or putting the lid on a pressure cooker.

User's manual NAVIGON 5100 | 5110

- 12 - Before you begin

1. Place the navigation device on the bayonet in such a way that the

bulges on the bayonet ring correspond exactly with the recesses on

the cradle. This is achieved by rotating it approx. 30° to the left.

2. Turn the navigation device clockwise until the bayonet fitting locks

into place.

3. Adjust the navigation device so that it can be seen easily.

Supplying power to the navigation device

Included in delivery of the NAVIGON 5100 | 5110 is a car charger cable

with which power can be supplied to the navigation device via the

vehicle's cigarette lighter.

The car charger cable is connected to the NAVIGON 5100 | 5110 via

the mini-USB-socket

on the bottom of the device.

Caution! The car charger cable is to be connected to cigarette lighters

with an operating voltage of 12V only.

Connecting the TMC-antenna

The NAVIGON 5100 | 5110 has an integrated TMC-receiver. For

optimal reception, you should use the TMC-antenna provided.

1. Connect the TMC-antenna to the headset socket

on the

bottom of the NAVIGON 5100 | 5110.

2. Secure the antenna to the windscreen using the suction cups.

2.4 Navigation with GPS

GPS is based on a total of 24 satellites that circle the earth and, in

doing so, are constantly transmitting their position and time. The GPS

receiver receives this data and calculates its own geographical position

on the basis of the information transmitted by the various satellites.

For a sufficiently precise positioning it is necessary to obtain the data

from at least three satellites. With the data from 4 or more satellites the

altitude above sea level can also be ascertained. The determination has

an accuracy of about 3 yards.

Once the navigation device has determined your position, this position

can be used as a starting point for route calculation.

The map data on your navigation device includes the geographical

coordinates of all digitally recorded points of interest, streets and

places. This enables the device to calculate a route between a starting

point and a destination.

User's manual NAVIGON 5100 | 5110

Before you begin - 13 -

The calculation of the current position and its representation on the map

takes place once every second. So your current position is always

shown on the map.

2.5 Important safety information

In your own interest, please read the following notices and safety

information carefully before starting up your navigation system.

2.5.1 Navigation safety information

Use navigation system at your own risk.

Caution! To prevent accidents, do not operate the navigation system

while driving.

Caution! Do not look at the display unless it is absolutely safe to do so!

Caution! Traffic regulations have priority over any instructions from the

navigation system.

Caution! Only follow the instructions of the navigation system when the

circumstances and the road traffic regulations allow you to do so! The

navigation system will guide you to your destination even if you deviate

from the calculated route.

Caution! Check that the cradle is secured and adjusted properly before

each journey.

Note: If you have not understood the spoken instructions, or you're not

sure about what to do next, you can refer briefly to the map or arrow

view of your navigation system.

2.5.2 Safety information for the navigation device

Caution! Protect the device from moisture. The device is neither

waterproof nor is it protected against splash water.

Caution! Do not run cables directly next to safety-relevant devices and

supply lines.

Caution! After installation, check all safety-relevant equipment in the

car.

User's manual NAVIGON 5100 | 5110

- 14 - Before you begin

Caution! Unplug the navigation device's power supply when you park

the vehicle. The navigation device requires power in standby-modus,

and may drain the vehicle's battery.

Caution! Do not open the navigation device's casing under any

circumstances.

Caution! Do not expose the navigation device to extreme heat or cold.

This may damage the device or impair its function.

Caution! Use only the charger provided or one that has been approved

of by the manufacturer.

Connect the charger to a suitable power supply. The voltage

requirements can be found on the device case and/or the packaging.

Note: Ensure that there are no kinks in the cable and that it will not be

damaged by any sharp objects.

Note: To clean the navigation device, use a moist cloth only.

Note: Do not unplug by pulling on the cable. Doing so could damage

the cable!

Note: Create a backup of the data contained on the memory card

provided.

Note: The memory card must remain inserted in the device during

operation of the navigation system.

Note: Use SD- or MMC-memory cards only! Ensure that memory card

contacts are clean and undamaged.

2.5.3 Safety guidelines when installing in your car

Caution! Secure the cradle and the TMC-antenna in such a way that

the driver's visibility is not impaired.

Caution! Do not attach the cradle within the deployment zone of

airbags.

User's manual NAVIGON 5100 | 5110

Operating the navigation software - 15 -

Caution! When installing the cradle, ensure that it does not represent a

risk in the event of an accident.

Caution! Do not run cables directly next to safety-relevant devices and

power supplies.

Caution! After installation, check all safety-relevant equipment in the

car.

Caution! The car charger cable is to be connected to cigarette lighters

with an operating voltage of 12V only.

3 Operating the navigation software

3.1 Volume

The volume of the spoken driving instructions can be adjusted during

navigation.

You have started navigation. The map is open in Navigation or

Destination search mode.

1. Tap the

(Volume) button.

The volume bar opens. It contains three buttons for adjusting the

volume:

(Louder), (Quieter), (Volume on/off).

2. Tap the

(Volume) button again.

The volume bar closes.

3.2 Information

Symbols located at the top of the screen are used to display

information.

GPS

The GPS symbol can show the following GPS-reception status:

No GPS: The built-in GPS receiver is not operational. Contact customer

service if the problem persists.

User's manual NAVIGON 5100 | 5110

- 16 - Operating the navigation software

No Signal: Data is being received from less than three satellites.

Position cannot be calculated.

GPS Ready: Data is being received from at least three satellites.

Position can be calculated.

For more detailed information regarding GPS status, please refer to

chapter "GPS status" on page

44.

Energy

The Energy symbol can display the following conditions of the built-in

battery:

The device is being supplied by an external power source. The battery

is being charged.

The device is being supplied by its internal battery. The battery charge

is sufficient.

The device is being supplied by its internal battery. The battery charge

is low.

Direction

The Direction symbol shows you in which direction you are currently

heading. It can show the following points of the compass: N, NE, E, SE,

S, SW, W and NW.

TMC (Traffic Information)

The NAVIGON 5100 | 5110 has an integrated TMC-receiver which

provides the navigation system with up to date traffic messaging. If

necessary, it can alter the route dynamically in order to avoid a traffic

jam for example.

Note: This function is only available if TMC traffic messages are being

transmitted in the country in which you are travelling. This is not the

case in all countries.

The TMC symbol can display the following TMC-reception status:

No Symbol

: There is no TMC receiver connected, or the connected or

built-in TMC receiver is not operational.

Tuning: The TMC-receiver is operational, but cannot find a station that

is transmitting TMC signals.

User's manual NAVIGON 5100 | 5110

Operating the navigation software - 17 -

TMC on Standby: Traffic messages can be received.

For details on TMC functionality, please refer to chapter "TMC (Traffic

Information)" on page

45.

3.3 Software keyboard

A software keyboard appears on the screen when text entries are

necessary.

All entries can be made on the software keyboard using the fingertips.

Only capital letters can be entered.

When entering town or street names you need not enter any special

characters or umlauts. The navigation system fills in these characters

for you automatically. If, for example, you are searching for “Würzburg”,

then simply enter "WURZBURG". Special characters may be helpful

when naming saved destinations and itineraries, however.

Special keys

enters a space character.

deletes the character in front of the cursor.

opens the numeric keypad.

opens the letter keyboard.

opens the special character keyboard. As soon as you have

entered a special character, the letter keyboard reappears

automatically.

3.4 Lists

Often, lists appear from which you can select an entry. This is the case,

for example, when you enter a location.

As soon as you enter the first letter, the largest city in the country

specified which begins with this letter appears.

As soon as you enter the second letter, a list appears with all locations

that begin with the letters entered.

If you enter additional letters, the list adapts to your entries. It only

contains entries that begin with the text that has been entered or

contain the text in the name. The more letters you enter, the shorter the

list will become.

User's manual NAVIGON 5100 | 5110

- 18 - Password Lock

You can toggle the list by means of the (Up) and (Down)

buttons.

In order to accept an entry from the list, simply tap on it.

The list closes as soon as you have accepted an entry.

3.5 Options

Some windows offer options that lead to further functions.

A description of all available options can be found in chapter "

Options"

on page

34.

3.6 Menus

Some buttons have menus which open when activated.

Tap on a menu button to execute its function.

If you would like to quit the options list without selecting a function, tap

on the button you used to open the menu.

4 Password Lock

By creating a password, you can protect your navigation system from

unauthoriised use.

Note: Password protection only comes into effect after the navigation

device has been switched off completely. To do this, press the

(On/Off/Standby

) switch for at least 6 seconds.

4.1 Activating password protection

1. In the MAIN WINDOW, tap on Options > Settings > Options >

Password Lock

.

The P

ASSWORD LOCK window opens.

2. Enter a new password in the New password

field.

3. Enter this password in the Confirm new password

field again.

4. Tap the Save password

button.

Note: The password must contain precisely 4 digits.

User's manual NAVIGON 5100 | 5110

Password Lock - 19 -

4.2 Changing a password

1. In the MAIN WINDOW, tap on Options > Settings > Options >

Password Lock

.

The P

ASSWORD LOCK window opens.

2. Enter the password that is currently valid in the Old password

field.

3. Enter a new password in the New password

field.

4. Enter the new password in the Confirm new password

field again.

5. Tap the Password Lock

button.

Note: The new password must contain precisely 4 digits.

4.3 Cancelling password protection

The PASSWORD LOCK window is open.

1. Tap on Options

> Deactivate password lock

2. Enter the password that is currently valid in the Enter password

field.

3. Tap the Deactivate password lock

button.

4.4 Switching on NAVIGON 5100 | 5110

1. Press the (On/Off/Standby) switch for at least 6 seconds.

If password protection has been activated, the E

NTER PASSWORD

window opens.

2. Enter the password.

3. Tap the Continue

button.

4.4.1 Forgotten your password?

If you have forgotten your password, proceed as follows:

1. Tap the

(Info) button.

2. Follow the instructions on the screen.

Note: This service incurs costs. Information on tarifs can be obtained

from your telecom provider.

User's manual NAVIGON 5100 | 5110

- 20 - Navigation

5 Navigation

Use navigation system at your own risk.

Caution! Please be sure to refer to the safety information in chapter

"

Important safety information" on page 13.

Impaired GPS reception

If GPS reception is impaired, navigation will be interrupted. The

navigation software remains active.

As soon as GPS reception is restored, the navigation system calculates

any change of position which has occurred in the meantime. Navigation

may simply be continued.

Arriving at your destination

When you have reached the specified destination, a message to this

effect will be displayed.

Only your current position (triangle in orange) will now be shown on the

map.

5.1 Starting NAVIGON 5100 | 5110

1. Switch your navigation device on.

Each time the navigation device has been switched off completely

(by pressing the

(On/Off/Standby) switch for at least 6 seconds)

the following message appears when the software is started again:

"Please note that the road traffic regulations are prior to the

instructions of the navigation system. Please do not operate the

device while driving."

2. After you have read and fully understood the text, tap the OK

button.

3. If you do not accept these instructions, then tap the Cancel

button

in order to quit the navigation software.

The M

AIN WINDOW will open. You can reach all of the navigation

software functions via the M

AIN WINDOW.

Page is loading ...

Navigon 5100 MAX User manual

This manual is also suitable for

Navigon 5100 MAX User manual

Related papers

Other documents