Guardian Technologies 2535 User manual
- Category
- Household fans
- Type
- User manual
This manual is also suitable for
Page is loading ...
Rev. G 10/08
2
2535ES
Rev. G 10/08
11
2535ES
MODELO 2535
FUNCIÓN DE PERSIANA (Figura 7)
Además de la función oscilante, este Ventilador está
equipado con persianas en la parrilla anterior, lo cual permite
ajustar verticalmente el flujo de aire. Haga girar el control
de persiana (Insertar 7A) hacia arriba o hacia abajo para
ajustar el flujo de aire según su preferencia.
Insertar 7A
Figura 7
CONTROL REMOTO (Figura 6)
1. Instale la baterías (no suministró) como mostrado en la Figura
6. La batería es el tipo “AAA”.
2. El Botón De Encendido del Control Remoto está identificado
como ( ).
3. Todas las funciones realizadas con el Control Remoto
pueden realizarse de igual forma con los Controles
Manuales.
4. No mezcle baterías viejas y nuevas. No mezcle baterías
alcalinas, estándar (carbono-cinc) o recargables (níquel-
cadmio).
5. No se deshága de baterías en el fuego. baterías pueden estallar
o pueden salirse.
Si usted pierde su mando a distancia, por favor Cliente
de llamada Serive para ordenar un reaplacement en 1-800
-233-0268, de lunes a viernes, entre las 8 a.m. y las 5 p.m.
(Horario Estándar del Este de los Estados Unidos).
Figura 6
Vista Frontal del
Control Remoto
Espalda De
Telemando
MODEL 5132
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce
the risk of fire, electrical shock and injury to persons, including the following:
SAVE THESE INSTRUCTIONS
Read all instructions before using this Fan.
1. Make certain the power source conforms to the electrical requirements of the Fan.
2. Make certain that the room is equipped with a working smoke detector.
3. Use this Fan only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock,
or injury to persons.
4. To reduce the risk of personal injury and electric shock, the Fan should not be played with or placed where small children can reach it.
5. Unplug power cord before installing, servicing, or moving the Fan.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING
OR MOVING THE FAN. ALWAYS UNPLUG THE POWER CORD. ALWAYS TURN OFF AND UNPLUG FAN BEFORE
LEAVING THE AREA. NEVER LEAVE CHILDREN UNATTENDED WHEN THE FAN IS ON OR PLUGGED IN.
6. This Fan must NOT be used in potentially dangerous locations such as flammable, explosive, chemical-laden or wet atmospheres
where gasoline, paint or flammable liquids are used or stored.
7. DO NOT use Fan in or near a window. Rain may create an electrical hazard.
8. Completely assemble Fan, according to instructions, before connecting to power supply.
REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK - DO NOT USE THIS FAN
WITH ANY SOLID STATE SPEED CONTROL DEVICES.
9. Where possible, avoid the use of extension cords because the extension cord may overheat and cause a fire. If you must use an exten-
sion cord, minimize the risk of overheating by using the shortest cord possible and ensuring that it is UL listed. NEVER use a single
extension cord to operate more than one Fan. Do not plug Fan into any other cord connected device, such as a power strip, cord
reel, surge protector, multiple outlet adapters or outlet-type air fresheners. The use of such devices may create a fire hazard.
10. NEVER operate any Fan with a damaged cord or plug or after the Fan malfunctions, has been dropped or damaged in any manner.
There are no user serviceable parts. Return Fan to an authorized service facility for examination, electrical or mechanical adjustment
or repair.
11. NEVER insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock or fire,
or damage the Fan. To reduce the risk of fire, DO NOT block or tamper with the Fan in any manner while it is in operation.
12. Always place the Fan on a stable, flat, level surface when operating, to avoid the chance of the Fan overturning. Locate the Power
Cord so the Fan or other objects are not resting on it. DO NOT run Power Cord under carpeting. DO NOT cover Power Cord with
throw rugs, runners or the like. Arrange Power Cord away from room traffic and where it will not be tripped over.
13. This Fan is not intended for use in wet or damp locations. Never locate a Fan where it may fall into a bathtub or other water container.
NEVER use Fan where flammable liquids are used or stored.
14. NEVER use Fan outdoors.
15. Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Fan. If this occurs,
move the Fan to another location.
16. Keep Fan remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Fan.
17. This Fan is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined. Please
refer to National Electric Code (NEC) Article 547-7 (2008), or applicable state or local codes or standards relating to electrical require-
ments for Agricultural Buildings. THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
18. This Fan is not suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or
local codes or standards relating to electrical requirements for Hazardous locations. THIS FAN DOES NOT MEET THE REQUIRE-
MENTS OF NEC ARTICLE 500 (2008).
This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock,
this plug is intended to fit in a polarized outlet only one way. Match wide blade of plug to wide slot. Fully
insert. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. DO NOT attempt to defeat this safety feature.
This plug is a safety feature, to reduce the risk of fire, electric shock and personal injury. DO NOT remove,
replace, repair or tamper with the originally supplied plug. If the Fan does not function properly, it may be due
to the safety device incorporated in this plug. Return to an authorized service center or call 800-233-0268,
Monday - Friday, between 8:00 a.m. and 5:00 p.m. EST. If the plug warning label is missing or damaged, call
the toll free number for a replacement label.
FUNCIONAMIENTO
Este Ventilador puede hacerse funcionar mediante los
Controles Manuales ubicados en la parte superior de la
unidad (como se muestra en la Figura 5) o con el Control
Remoto (se muestra en la Figura 6).
1. Coloque el ventilador sobre una superficie firme y
nivelada.
2. Conecte el cable eléctrico a un tomacorriente
de 120 voltios.
Asegúrese que el enchufe encaje firmemente en el
tomacorriente.
Cuando los enchufes quedan flojos en los
tomacorrientes, pueden deslizarse parcial
o completamente fuera del tomacorriente
con un leve movimiento del cable adosado.
Los tomacorrientes en este estado podrían
sobrecalentarse y representar un grave peligro
de incendio; si está cubierto por una cortina o
tela, el riesgo de incendio es aún mayor.
3. Encienda el Ventilador presionando el Botón de
Encendido ( ).
4. VELOCIDADES: Ajuste la velocidad del Ventilador
oprimiendo el Botón de Velocidad ( ). Cada vez que
se oprima el botón de velocidad, cambiará la velocidad,
de Baja (1) a Media (2) a Alta (3). Cuando se lo conecta
inicialmente, el Ventilador estará en Velocidad Baja.
Cuando el Ventilador se apaga y se enciende nuevamente,
la unidad volverá a la velocidad en la cual estaba cuando
fue apagado.
5. OSCILACIÓN: Oprima el Botón de Oscilación ( ) para
activar y desactivar la función de oscilación.
MODELO 2535
Rev. G 10/08
10
2535ES
Rev. G 10/08
3
2535ES
MODEL 2535
STAND ASSEMBLY (Figure 3)
PLACE BASE FLAT ON FLOOR
1. With a twisting motion, insert the end of the large diameter
pipe into hole in Base. Turning pipe while pushing will assure
pipe is fully seated in base.
2. FOR HEIGHT ADJUSTMENT:
a) Loosen Height Adjustment Nut.
b) Raise or lower Extension Pipe to desired height.
c) Tighten Height Adjustment Nut.
HEAD ASSEMBLY (Figure 4)
1. Place Head Assembly onto end of Extension Pipe Assembly by
twisting Head Assembly downward until seated on Extension
Pipe Assembly.
PIPE ASSEMBLY (Figure 1)
1. Take pipe assembly out of carton as shown.(Step 1)
2. Loosen Height Adjustment Nut turning counter clockwise.
(Step 2)
3. Raise Extension Pipe. (Step 3)
4. Tighten Height Adjustment Nut turning clockwise. (Step 4)
BASE ASSEMBLY (Figure 2)
1. Assemble Base by interlocking the Bosses into the Boss
Holes on the Bottom of Base.
2. Secure the (5) #8 X 1/2" Screws into the Boss Holes on the
Bottom of Base. (Figure 2)
Figure 4
Extension Pipe Assembly
Head Assembly
Base
Extension Pipe
Assembly
Height Adjustment
Nut
Figure 3
Head Assembly
Figura 5
6. TEMPORIZADOR: La función temporizadora le permitirá
ajustar el tiempo de funcionamiento de 1/2 hora a 7
1/2 horas, con incrementos de 1/2 hora. Al oprimir
el Botón Temporizador ( ), cambiará el tiempo de
funcionamiento deseado. Cada vez para que presione
el botón temporizador, el tiempo aumenta en 1/2 hora.
Después de llegar a las 7 1/2 horas, si oprime el botón
temporizador una vez más, el ventilador funcionará en
forma continua. Las luces en el frente de la unidad se
encenderán apropiadamente con el lapso de tiempo para
el cual se activó el Ventilador.
7. MODO DE SUEÑO: Esta función permite que la unidad
se coloque en Modo de Sueño. Al oprimir el Botón de
Modo de Sueño ( ) una vez, cambiará la velocidad de
la Unidad a baja durante 6 horas continuas. Al apretar el
Botón de Modo de Sueño ( ) una segunda vez, la unidad
se colocará en 6 horas continuas. El Botón de Oscilación
( ) funcionará cuando el Ventilador esté en el Modo de
Sueño. Al apretar cualquier otro botón (Temporizador,
Velocidad del Ventilador o de Encendido) se cerrará el
Modo de Sueño.
8. Para apagar el Ventilador, presione el Botón de Encendido
( ) y desenchufe la unidad del tomacorrientes.
Figure 2
(5) #8 X 1/2" Screws
Bosses
BOTTOM OF BASE
Boss
Holes
Extension
Pipe
Height
Adjustment
Nut
Step 1
Step 3
Step 4
Step 2
Figure 1
Extension
Pipe
Height
Adjustment
Nut
TOOLS REQUIRED FOR ASSEMBLY (not included)-
#2 Phillips Head Screwdriver
OPERATION
This Fan may be operated by the Manual Controls located
on top of the unit (as shown in Figure 5) or by the Remote
Control (shown in Figure 6).
1. Place the Fan on a firm and level surface.
2. Plug the cord set into a 120 volt outlet.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles, they
may slip partially or completely out of the re-
ceptacle with only the slight movement of the
attached cord. Receptacles in this condition
may overheat and pose a serious fire hazard; if
covered by a curtain or drape, the fire hazard
is even greater.
3. Turn the Fan ON by pressing the Power Button ( ).
4. SPEEDS: Press the Fan Speed Button ( ) to desired
speed setting. Each time the Fan Speed Button is
pressed, the speed will change from Low (1), to Medium
(2), to High (3). When intially plugged in, the Fan will be in
Low Speed. When the Fan is turned OFF and ON again,
the unit will resume the speed at which it was turned
OFF.
5. OSCILLATION: Press the Oscillation Button ( ) to start
and stop the oscillation function.
6. TIMER: The timer function allows the unit to be set to
MODEL 2535
Rev. G 10/08
4
2535ES
Rev. G 10/08
9
2535ES
Figure 5
ARMADO DE LA TUBERÍA (Figura 1)
1. Saque el conjunto de la tubería del cartón como muestra. (Paso 1)
2. Desafloje la Tuerca De Ajuste De Altura, girando en sentido
contrahorario. (Paso 2)
3. Eleve la Extensión De La Tubería. (Paso 3)
4. Apriete la Tuerca De Ajuste De Altura, girando en sentido
horario. (Paso 4)
MODELO 2535
ARMADO DE LA BASE (Figura 2)
1. Arme la Base entrecerrando las Copas en los Orificios De Copa
situados en la Parte Inferior De La Base.
2. Fije (5) Tornillos #8 X 1/2" en los Orificios De Copa en la Parte
Inferior De La Base.
CONJUNTO DE LA CABEZA (Figura 4)
1. Coloque el Conjunto del Cabezal sobre el extremo del Extensión
De La Tubería torciendo Conjunto del Cabezal abajo hastaquese
siente en el Extensión De La Tubería. (Figura 4)
Figura 4
Extensión De La Tubería
Conjunto del Cabezal
ENSAMBLE DEL PIE (Figura 3)
COLOQUE LA BASE EN EL PISO
1. Utilizando un movimiento giratorio, inserte el extremo del tubo de
diámetro grande en el agujero de la Base. El girar el tubería a me-
dida que se lo empuja asegura que el tubería quede plenamente
asentado en la base.
2. PARA AJUSTAR LA ALTURA:
a) Afloje la Tuerca De Ajuste De Altura.
b) Eleve o baje el Extensión De La Tubería hasta obtener la
altura deseada.
c) Apriete la Tuerca De Ajuste De Altura.
Base
Extensión De La Tubería
Tuerca De Ajuste De Altura
Figura 3
Conjunto del Cabezal
Figura 2
(5) Tornillos #8 X 1/2"
Copas
PARTE INFERIOR DE LA BASE
Orificios
De Copa
operate for a length of time from 1/2 hour to 7 1/2 hours,
in increments of a 1/2 hour. Press the Timer Button ( )
to set the length of time desired. Each time the timer
button is pressed, the time is increased by 1/2 hour.
After reaching 7 1/2 hours, pressing the timer button
once more will reset the Fan to continuous running. The
lights on the front of the unit will light up appropriately
with the length of time that the Fan is set for.
7. SLEEP: This function allows the unit to be set in Sleep
Mode. Pressing the Sleep Button ( ) once will set
the unit on Low for 6 continuous hours. Pressing the
Sleep Button ( ) a second time will reset the unit to 6
continuous hours. The Oscillation Button ( ) will function
when the Fan is in Sleep Mode. Pressing any other button
(Timer, Fan Speed or the Power Button) will shut off the
Sleep Mode.
8. To turn the Fan OFF, press the Power Button ( ) and
unplug the unit from the electrical outlet.
Figura 1
Extensión De
La Tubería
Tuerca De
Ajuste De
Altura
Paso 1
Paso 3
Paso 4
Paso 2
Extensión De
La Tubería
Tuerca De
Ajuste De
Altura
HERRAMIENTAS NECESARIAS PARA EL
ARMADO (no incluida)
- Destornillador de Cabeza Phillips # 2
Page is loading ...
Rev. G 10/08
6
2535ES
MODEL 2535
MAINTENANCE
To reduce the risk of electrical shock and fire please observe the following instructions:
- Always unplug the cord before moving, servicing or cleaning.
- NEVER place the Fan in or near water.
- Clean the Fan only with a vacuum equipped with a brush attachment; the vacuum will remove the lint
and dirt from inside the Fan.
- NEVER attempt to take apart the Fan.
- Clean the body of the Fan with a soft cloth only.
- NEVER use ALCOHOL or SOLVENTS such as gasoline, benzene, paint thinner, or other harsh cleaners.
INSTRUCCIONES IMPORTANTES -
MANUAL DE OPERACIÓN
LEA Y GUARDE ESTAS INSTRUCCIONES
LEA CUIDADOSAMENTE LAS INSTRUCCIONES ANTES DE
INTENTAR ARMAR, INSTALAR, USAR O DAR MANTENIMIENTO
AL PRODUCTO DESCRITO.
PROTÉJASE A SÍ MISMO Y A LOS DEMÁS CUMPLIENDO CON
TODA LA INFORMACIÓN DE SEGURIDAD. EL NO SEGUIR
LAS INSTRUCCIONES PODRÍA RESULTAR EN LESIONES
PERSONALES Y/O DAÑOS A LA PROPIEDAD.
CONSERVE LAS INSTRUCCIONES COMO FUTURA REFERENCIA.
CONSERVE ESTAS INSTRUCCIONES
Rev. G 10/08
7
2535ES
SERVICING: All other servicing, with the exception of general user-maintenance, should be performed by an authorized service
representative. Call 1-800-233-0268, Monday through Friday, between the hours of 8:00 a.m. and 5:00 p.m. EST for the location of
your nearest service center.
STORAGE: Store the Fan with these instructions, in the original carton in a cool, dry place.
VENTILADOR DE PEDESTAL OSCILANTE
AHORRATIVO EN ESPACIO DE 52"
CON CONTROL REMOTO
MODELO 2535
TROUBLE SHOOTING TIPS
If your Fan fails to operate, see below for a list of probable causes and solutions:
1. Be sure the power cord is plugged into a working electrical outlet.
2. Make certain the batteries in the remote control are new and properly installed.
If you have a problem that can not be resolved by the steps listed above, contact Technical Assistance at 1-800-233-0268, Monday
through Friday, between the hours of 8:00 a.m. and 5:00 p.m. EST.
Este Ventilador es sólo para uso residencial.
No está destinado para ser usado en instalaciones comerciales, industriales o agricultura.
LASKO PRODUCTS, INC. LIMITED WARRANTY
(NOT VALID IN MEXICO)
WHAT THIS WARRANTY COVERS: This product is warranted against defects in workmanship and/or materials.
HOW LONG THIS WARRANTY LASTS: This warranty extends only to the original purchaser of the product and lasts for one (1) year from the date of
original purchase or until the original purchaser of the product sells or transfers the product, whichever first occurs.
WHAT LASKO WILL DO: During the warranty period, Lasko will, at its sole option, repair or replace any part or parts that prove to be defective or
replace the whole product with the same or comparable model.
WHAT THIS WARRANTY DOES NOT COVER: This warranty does not apply if the product was damaged or failed because of accident, improper
handling or operation, shipping damage, abuse, misuse, unauthorized repairs made or attempted. This warranty does not cover shipping costs for the
return of products to Lasko for repair or replacement. Lasko will pay return shipping charges from Lasko following warranty repairs or replacement.
ANY AND ALL WARRANTIES, EXPRESSED OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY),
LAST ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE OR UNTIL THE ORIGINAL PURCHASER OF THE PRODUCT SELLS OR TRANSFERS
THE PRODUCT, WHICHEVER FIRST OCCURS AND IN NO EVENT SHALL LASKO’S LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY
INCLUDE (I) INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM ANY CAUSE WHATSOEVER, OR (II) REPLACMENT OR REPAIR OF ANY
HOUSE FUSES, CIRCUIT BREAKERS OR RECEPTACLES. NOTWITHSTANDING ANYTHING TO THE CONTRARY, IN NO EVENT SHALL LASKO’S
LIABILITY UNDER ANY EXPRESS OR IMPLIED WARRANTY EXCEED THE PURCHASE PRICE OF THE PRODUCT AND ANY SUCH LIABILITY SHALL
TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD.
Some states and provinces do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential
damages, so these exclusions or limitations may not apply to you. This warranty gives you specific legal rights. You may also have other rights which
vary from state to state and province to province.
Proof of purchase is required before a warranty claim will be accepted.
CUSTOMER SERVICE:
Toll-Free (800) 233-0268. Email: pr[email protected]
Our Customer Service team is available to assist you with product questions, service center locations, and replacement parts. They
can be reached Monday through Friday, 8am-5pm Eastern. Please have your model number available, as well as the type and style
(located on the underside of your product). Please do not return product to place of purchase.
Customer Service Dept., 820 Lincoln Ave., West Chester, PA 19380
(Please do not send product to this location)
www.laskoproducts.com
Manual printed in China
-
1
-
2
-
3
-
4
-
5
-
6
Guardian Technologies 2535 User manual
- Category
- Household fans
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
Related papers
-
Lasko LAS3300 User manual
-
Lasko 4000 User manual
-
-
Lasko Blower 4924 User manual
-
-
-
-
Guardian Technologies 2648 User manual
-
Lasko 2520 User manual
-
Lasko Model T42954 User manual