Craftsman ZT Zero 22 User manual

Operator's Manual

ZT 7000

Zero-Turn Rear Engine Rider

18 HP, 50" Mower

Electric Start

Model No.

107.277700

CAUTION: Before using this product, read

the manual and follow all its Safety Rules

and Operating Instructions,

For answers to your questions about this

product, call:

1-800-659-5917

Sears Craftsman Help Line

5 am - 5 pm, Mon - Sat

Nota: Una traducci6n en espaSol de este Manual

del Operador puede encontrarse en la pAgina 33.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website: www.sears.com/craftsman

TP 199-3928-07-CZ-C

1726431-07

Nota: Una traducci6n en espaRol de este Manual del Operador puede encontrarse en la p_.gina 33.

Warranty Statement ..................................................... 2

Safety Rules & information ......................................... 3

identification Numbers ................................................ 7

Optional Accessories .................................................. 8

Literature Package Contents ...................................... 8

Pre-Operation ............................................................... 9

Operation .................................................................... 10

Maintenance ............................................................... 17

Service & Adjustments ............................................. 26

Storage ....................................................................... 30

Troubleshooting ......................................................... 31

Spanish Operator's Manual ...................................... 33

Repair Parts ......................................................... PTS=I

Repair Protection Agreement ........ inside Back Cover

NOTE: In this manual, "left"and "right"are referred to as seen from the operating position.

LIMITED WARRANTY ON CRAFTSMAN RIDING EQUIPMENT

For two (2) years from the date of purchase, if this Craftsman riding equipment is maintained, lubricated and tuned up

according to the instructions in the owner's manual, Sears will repair or replace free of charge any parts that are

found to be defective in material or workmanship according to the guidelines of coverage listed below. Sears will also

provide free labor for these applicable warrantied parts for the two full years. During the first 30 days of purchase,

there will be no charges to service the product at your home for issues covered by this warranty. (See exclusions

below). For your convenience, IN HOME warranty service will still be available after the first 30 days of purchase, but

a trip charge will apply. This charge will be waived if the Craftsman product is dropped off at an authorized Sears loca-

tion. For the nearest authorized Sears location, please call 1-800-MY-HOME. This warranty applies only while this

product is within the United States.

THIS WARRANTY DOES NOT COVER:

• Expendable items which become worn during normal

use, including but not limited to blades, spark plugs,

air cleaners, belts, and oil filters.

• Standard maintenance servicing, oil changes, or

tune-ups.

• Tire replacement or repair caused by punctures from

outside objects, such as nails, thorns, stumps, or

glass.

• Repairs necessary because of operator abuse,

including but not limited to, damage caused by towing

objects beyond the capability of the riding equipment,

impacting objects that bend the frame or crankshaft,

or over-speeding the engine.

LIMITED WARRANTY ON BATTERY

Repairs necessary because of operator negligence,

including but not limited to, electrical and mechanical

damage caused by improper storage, failure to use

the proper grade and amount of engine oil, failure to

keep the deck clear of flammable debris, or failure to

maintain the equipment according to the instructions

contained in the owner's manual.

• Engine (fuel system) cleaning or repairs caused by

fuel determined to be contaminated or oxidized

(stale). In general, fuel should be used within 30 days

of its purchase date.

• Normal deterioration and wear of the exterior of the

exterior finishes, or product label replacement.

Riding equipment used for commercial or rental pur-

poses.

For ninety (90) days from date of purchase, if any battery included with this riding equipment proves defective in

material or workmanship and our testing determines the battery will not hold a charge, Sears will replace the battery

at no charge. During the first 30 days of purchase, there will be no charges to replace the battery at your HOME. After

first 30 days, for your convenience, IN-HOME warranty service will still be available but a trip charge will apply. This

charge will be waived if the Craftsman product is dropped off at an authorized Sears location. FOR THE NEAREST

AUTHORIZED LOCATION, PLEASE CALL 1-800-4-MY-HOME. This battery warranty applies only while this product

is within the United States.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

Readthesesafetyrulesandfollowthemclosely.Failuretoobeytheserulescouldresultinlossofcontrol

ofunit,severepersonalinjuryordeathtoyou,orbystanders,ordamagetopropertyorequipment.

This mowing deck is capable of amputating hands and feet and throwin og_bjb'ects.

The triangle _ in text signifies important cautions or warnings which must be followed.

GENERAL OPERATION

t. Read, understand, and follow all instructionsin the

manual and on the unit before starting.

2. Do not put hands or feet near rotating parts or under

the machine. Keep clear of the discharge opening at

all times.

3. Only allow responsible adults, who are familiar with

the instructions, to operate the unit (local regulations

can restrict operator age).

4. Clear the area of objects such as rocks, toys, wire,

etc., which could be picked up and thrown by the

blade(s).

5. Be sure the area is clear of other people before mow-

ing. Stop the unit if anyone enters the area.

6. Never carry passengers.

7. Do not mow in reverse unless absolutely necessary.

Always look down and behind before and while travel-

ling in reverse.

8. Never direct discharge material toward anyone. Avoid

discharging material against a wall or obstruction.

Material may ricochet back toward the operator. Stop

the blade(s) when crossing gravel surfaces.

9. Do not operate the machine without the entire grass

catcher, discharge guard (deflector), or other safety

devices in place.

10. Slow down before turning.

11. Never leave a running unit unattended. Always disen-

gage the PTO, set parking brake, stop engine, and

remove keys before dismounting.

12. Disengage blades (PTO) when not mowing. Shut off

engine and wait for all parts to come to a complete

stop before cleaning the machine, removing the grass

catcher, or unclogging the discharge guard.

13. Operate the machine only in daylight or good artificial

light.

14. Do not operate the unit while under the influence of

alcohol or drugs.

15 Watch for traffic when operating near or crossing

roadways.

16. Use extra care when loading or unloading the unit

into a trailer or truck.

17. Always wear eye protection when operating this unit.

18. Data indicates that operators, age 60 years and

above, are involved in a large percentage of riding

mower-related injuries. These operators should eval-

uate their ability to operate the riding mower safely

enough to protect themselves and others from injury.

19. Follow the manufacturer's recommendations for wheel

weights or counterweights.

20. Keep in mind the operator is responsible for accidents

occurring to other people or property.

21. All drivers should seek and obtain professional and

practical instruction.

22. Always wear substantial footwear and trousers.

Never operate when barefoot or wearing sandals.

23. Before using, always visually check that the blades

and blade hardware are present, intact, and secure.

Replace worn or damaged parts.

24. Disengage attachments before: refueling, removing

an attachment, making adjustments (unless the

adjustment can be made from the operator's posi-

tion).

25. When the machine is parked, stored, or left unattend-

ed, lower the cutting means unless a positive

mechanical lock is used.

26. Before leaving the operator's position for any reason,

engage the parking brake, disengage the PTO, stop

the engine, and remove the key.

27. To reduce fire hazard, keep the unit free of grass,

leaves, & excess oil. Do not stop or park over dry

leaves, grass, or combustible materials.

28. It is a violation of California Public Resource Code

Section 4442 to use or operate the engine on or near

any forest-covered, brush-covered, or grass-covered

land unless the exhaust system is equipped with a

spark arrester meeting any applicable local or state

laws. Other states or federal areas may have similar

laws.

TRANSPORTING AND STORAGE

t. When transporting the unit on an open trailer, make

sure it is facing forward, in the direction of travel. If

the unit is facing backwards, wind lift could damage

the unit.

2. Always observe safe refueling and fuel handling prac-

tices when refueling the tractor after transportation or

storage.

3. Never store the unit (with fuel) in an enclosed poorly

ventilated structure. Fuel vapors can travel to an igni-

tion source (such as a furnace, water heater, etc.)

and cause an explosion. Fuel vapor is also toxic to

humans and animals.

TP 600-2459-06-UV-SIvIA

4. Always follow the operator's manual instructions for

storage preparations before storing the tractor for

both short and long term periods.

5. Always follow the engine manual instructions for

proper start-up procedures when returning the unit to

service.

6. Never store the unit or fuel container inside where

there is an open flame or pilot light, such as in a

water heater. Allow unit to cool before storing.

SLOPE OPERATION

Slopes are a major factor related to loss-of-control and tip-

over accidents, which can result in severe injury or death.

Operation on all slopes requires extra caution, if you cannot

back up the slope or if you feel uneasy on it, do not operate

on it.

Control of a ride-on machine sliding on a slope will not be

regained by the application of the brake. The main reasons

for loss of control are: insufficient tire grip on the ground,

speed too fast, inadequate braking, the type of machine is

unsuitable for its task, lack of awareness of the ground con-

ditions, incorrect hitching and load distribution.

1. Mow up and down slopes, not across.

2. Watch for holes, ruts, or bumps. Uneven terrain could

overturn the unit. Tall grass can hide obstacles.

3. Choose a slow speed so that you will not have to stop

or change speeds while on the slope.

4. Do not mow on wet grass. Tires may lose traction.

5. Always keep unit in gear especially when traveling

down slopes. Do not shift to neutral and coast down-

hill.

6. Avoid starting, stopping, or turning on a slope. If tires

lose traction, disengage the blade(s) and proceed

slowly straight down the slope.

7. Keep all movement on slopes slow and gradual. Do

not make sudden changes in speed or direction,

which could cause the machine to rollover.

8. Use extra care while operating machines with grass

catchers or other attachment; they can affect the sta-

bility of the unit.

9. Do not try to stabilize the machine by putting your

foot on the ground.

10. Do not mow near drop-offs, ditches, or embank-

ments. The mower could suddenly turn over if a

wheel is over the edge of a cliff or ditch, or if an edge

caves in.

11. Do not use grass catchers on steep slopes.

12. Do not mow slopes you cannot back up.

13. See your authorized retailer for recommendations of

wheel weights or counterweights to improve stability.

14. Remove obstacles such as rocks, tree limbs, etc.

15. Use slow speed. Tires may lose traction on slopes

even through the brakes are functioning properly.

16. Do not turn on slopes unless necessary, and then,

turn slowly and gradually downhill, if possible.

TOWED EQUIPMENT

1. Tow only with a machine that has a hitch designed for

towing. Do not attach towed equipment except at the

hitch point.

2. Follow the manufacturer's recommendations for

weight limit for towed equipment and towing on

slopes.

3. Never allow children or others in or on towed equip-

ment.

4. On slopes, the weight of the towed equipment may

cause loss of traction and loss of control.

5. Travel slowly and allow extra distance to stop.

6. Do not shift to neutral and coast down hill.

WARNING

Never operate on slopes greater than 17.6 percent

(10 °) which is a rise of 3-1/2 feet (106 cm) vertically in

20 feet (607 cm) horizontally.

When operating on slopes use additional wheel

weights or counterweights. See your retailer to

determine which weights are available and

appropriate for your unit.

Select slow ground speed before driving onto slope.

In addition to front and rear weights, use extra caution

when operating on slopes with rear-mounted grass

catcher.

Mow UP and DOWN the slope, never across the face,

use caution when changing directions and DO NOT

START OR STOP ON SLOPE.

CHILDREN

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the unit

and the mowing activity. Never assume that children will

remain where you last saw them.

1. Keep children out of the mowing area and under the

watchful care of another responsible adult.

2. Be alert and turn unit off if children enter the area.

3. Before and during reverse operation, look behind and

down for small children.

4. Never carry children, even with the blade(s) off. They

may fall off and be seriously injured or interfere with

safe unit operation. Children who have been given

rides in the past may suddenly appear in the mowing

area for another ride and be run over or backed over

by the machine.

5. Never allow children to operate the unit.

6. Use extra care when approaching blind corners,

shrubs, trees, or other objects that may obscure

vision.

EMISSIONS

1. Engine exhaust from this product contains chemicals

known, in certain quantities, to cause cancer, birth

defects, or other reproductive harm.

2. Look for the relevant Emissions Durability Period and

Air Index information on the engine emissions label.

IGNITION SYSTEM

1. This spark ignition system complies with Canadian

ICES-O02.

SERVICE AND MAINTENANCE

Safe Handling of Gasoline

1. Extinguish all cigarettes, cigars, pipes, and other

sources of ignition.

2. Use only approved gasoline containers.

3. Never remove the gas cap or add fuel with the engine

running. Allow the engine to cool before refueling.

4. Never fuel the machine indoors.

5. Never store the machine or fuel container where there

is an open flame, spark, or pilot light such as near a

water heater or other appliance.

6. Never fill containers inside a vehicle or on a truck bed

with a plastic bed liner. Always place containers on

the ground away from your vehicle before filling.

7. Remove gas-powered equipment from the truck or

trailer and refuel it on the ground, if this is not possi-

ble, then refuel such equipment on a trailer with a

portable container, rather than from a gasoline dis-

penser nozzle.

8. Keep nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is com-

plete. Do not use a nozzle lock-open device.

9. if fuel is spilled on clothing, change clothing immedi-

ately.

10. Never over fill the fuel tank. Replace gas cap and

tighten securely.

11. Use extra care in handling gasoline and other fuels.

They are flammable and vapors are explosive.

12. If fuel is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors

have dissipated.

13. Replace all fuel tank caps and fuel container caps

securely.

Service & Maintenance

1. Maintain or replace safety and instruction labels as

necessary.

2. Never run the unit in an enclosed area where carbon

monoxide fumes may collect.

3. Keep nuts and bolts, especially blade attachment

bolts, tight and keep equipment in good condition.

4. Never tamper with safety devices. Check their proper

operation regularly and make necessary repairs if

they are not functioning properly.

5. Keep unit free of grass, leaves, or other debris build-

up. Clean up oil or fuel spillage.

6. Stop and inspect the equipment if you strike an

object. Repair, if necessary, before restarting.

7. Never make adjustments or repairs with the engine

running unless specified otherwise in the owner's

manual.

8. Do not remove the fuel filter when the engine is hot

as spilled gasoline may ignite. Do not spread fuel line

clamps further than necessary. Ensure clamps grip

hoses firmly over the filter after installation.

9. Do not use gasoline containing METHANOL, gasohol

containing more than 10% ETHANOL, gasoline addi-

tives, or white gas because engine/fuel system dam-

age could result.

10. If the fuel tank must be drained, it should be drained

outdoors.

11. Replace faulty silencers/mufflers.

12. Grass catcher components are subject to wear, dam-

age, and deterioration, which could expose moving

parts or allow objects to be thrown. Frequently check

components and replace with manufacturer's recom-

mended parts, when necessary.

13. Mower blades are sharp and can cut. Wrap the

blade(s) or wear gloves, and use extra caution when

servicing them.

14. Check brake operation frequently. Adjust and service

as required.

15. Use only factory authorized replacement parts when

making repairs.

16. Always comply with factory specifications on all set-

tings and adjustments.

17. Only authorized service locations should be utilized

for major service and repair requirements.

18. Never attempt to make major repairs on this unit

unless you have been properly trained, improper

service procedures can result in hazardous operation,

equipment damage and voiding of manufacturer's

warranty.

19. On multiple blade mowers, take care as rotating one

blade can cause other blades to rotate.

20. Do not change engine governor settings or over-

speed the engine. Operating the engine at excessive

speed can increase the hazard of personal injury.

21. Disengage drive attachments, stop the engine,

remove the key, and disconnect the spark plug wire(s)

before: clearing attachment blockages and chutes,

performing service work, striking an object, or if the

unit vibrates abnormally. After striking an object,

inspect the machine for damage and make repairs

before restarting and operating the equipment.

22. Never place hands near the moving parts, such as a

hydro pump cooling fan, when the tractor is running.

(Hydro pump cooling fans are typically located on top

of the transaxle).

23. Units with hydraulic pumps, hoses, or motors: WARN-

iNG: Hydraulic fluid escaping under pressure may

have sufficient force to penetrate skin and cause seri-

ous injury. Ifforeign fluid is injected into the skin it

must be surgically removed within a few hours by a

doctor familiar with this form of injury or gangrene

may result. Keep body and hands away from from pin

holes or nozzles that eject hydraulic fluid under high

pressure. Use paper or cardboard, and not hands, to

search for leaks. Make sure all hydraulic fluid con-

nections are tight and all hydraulic hoses and lines

are in good condition before applying pressure to the

system. If leaks occur, have the unit serviced imme-

diately by an authorized service center.

24. WARNING: Stored energy device, improper release

of springs can result in serious personal injury.

Springs should only be removed by an authorized

service center.

25. Models equipped with an engine radiator: WARNING:

Stored energy device. To prevent serious bodily injury

from hot coolant or steam blow-out, never attempt to

remove the radiator cap while the engine is running.

Stop the engine and wait until it is cool. Even then,

use extreme care when removing the cap.

SAFETY & OPERATION DECALS

This unit has been designed and manufactured to pro-

vide you with the safety and reliability you would expect

from an industry leader in outdoor power equipment

manufacturing.

Although reading this manual and the safety instructions

it contains will provide you with the necessary basic

knowledge to operate this equipment safely and effec-

tively, we have placed several safety labels on the unit to

remind you of this important information while you are

operating your unit.

OPERATION

Decal - Operation, Upper

Part No. 1726429

Decal - Danger/Warning, Lower

Part No. 1726430

Decal - Ignition

Switch

Part No. 1726526

All DANGER, WARNING, CAUTION and instructional

messages on your rider and mower should be carefully

read and obeyed. Personal bodily injury can result when

these instructions are not followed. The information is for

your safety and it is important! The safety decals below

are on your rider and mower.

If any of these decals are lost or damaged, replace them

at once. Contact a Sears Parts & Service Center for

replacements.

These labels are easily applied and will act as a constant

visual reminder to you, and others who may use the

equipment, to follow the safety instructions necessary for

safe, effective operation.

Decal - Sealed

Hydraulic System

Part No. 1726525

Decal - Transmission

Release Valve

Part No. 1726834

Decal - Cutting

Height Adjustment

Part No. 1721197

Decal - Ground Speed

Control - LH / RH

Part No. 1725671 / 1725670

Decal - Parking

Brake

Part No. 1726529

//ROTATI,GOUTTI.GBLAOE//

/

Decal - Danger,

Rotating Blades

Part No. 1704277

Decal - Danger,

Rotating Blades

Part No. 1704276

IIIlillllllllll

Iliiillililllil

When contacting the service center for replacement

parts, service, or information you MUST have these

numbers.

Record your model name/number, manufacturer's identi-

fication numbers, and engine serial numbers in the

space provided for easy access.

The identification tag is located on the underside of the

seat deck. Tilt the seat deck forward to access the ID

tag.

For answers to your questions about this product, call:

1-800-659-5917

Sears Craftsman Help Line, 5 am - 5 pm,

Monday-Saturday.

\

Model Description Name/Number

Stock Number Unit Serial Number

Date Purchased

Engine Make Engine Model

Engine Type/Spec Engine Code/Serial Number

- Twin Bag Grass Catcher

- Headlight Kit

• Bumper Kit

• Wheel Weights

Setup instructions - Setup instructions - Operator's Manual & Parts

English Spanish Book - English/Spanish

Setup

in6E_y Step:

Troubleshooting

Setup

i_,_ _asvStep_:

......... _,_ ,,=__,

2._ _2:_:_s._ _2_)_u_'

Troubleshooting

Oper_toCsManu_l

Z_ 7OOO

_ri, rt

Keys

m

Read The Operator's

Manual

• Read the operator's manual.

You should always read and follow

the instructions in the Operator's

manual. Proper care, performance tips, and safety

information is located in this important document.

1

Always Check the Oil

Level

Check the engine oil level.

The engine in your tractor has been

shipped, from the factory, already

filled with 10W-30 weight oil for use during the engine

break-in period. Always check the oil level before

starting the engine.

m

Push Unit Off Crate

To push the unit off the crate:

Set both transmission release levers

to PUSH position by pulling the levers

back (levers are located under the trail-

er hitch).

Cut the steel banding securing rider to pallet (6 bands).

Set the parking brake to DRIVE position.

Set the mower cutting height to its highest setting.

Fold the cardboard used to crate the unit in half, and

place it under the front wheels of the unit.

Push the unit forward off the crate.

• Set the transmission release valve levers back to

DRIVE positions (levers pushed in).

3m

4m

5m

Fill=Up with FRESH

Gasoline

Fill the tank with fresh fuel.

The single most common service

issue is stale or contaminated fuel!

Fuel should not be more than 30 days old. Use fuel

stabilizer to extend the life of your fuel, and always

store fuel in an approved, sealed, plastic gas can.

Stale fuel clean-out is not covered under your war-

ranty.

one hour at 6-10

Charge The Battery

• Lift the seat deck to access the

battery. If the unit is put into service

after the month and year indicated

on the battery date tag (located on

top of battery) charge the battery for

amps. Refer to the SERVICE &

ADJUSTMENTS section of the operator's manual for

battery charging information.

Check Tire Pressure

Reduce the tire pressures to the

pressures shown below. Tires are

over-inflated for shipping purposes,

and must be set to the correct pres-

sures for optimum traction.

Rear Tire Pressure: 10-12 PSI

m

Start The Engine

OFF

"_, RUN TOstart the engine:

'_ • While sitting in the operator's seat, set

START the parking brake to PARK. Make sure

the yellow PTO switch is OFF and the

ground speed control levers are locked

in PARK positions.

Move the engine throttle control fully forward to

CHOKE.

NOTE: A warm engine may not require choking. In this

case, set the throttle control to FAST.

insert the key into the ignition switch and turn it to

START.

After the engine starts, gradually move the throttle con-

trol back to FAST position (choke open). Warm the

engine by running it for at least a minute before turning

on the PTO switch, or driving the unit.

After warming the engine, ALWAYS operate the unit

with the throttle set to FAST position when mowing.

See the OPERATION section driving information.

Front Tire Pressure: 18-20 PSi

_Left Ground RightGround

SpeedLever SpeedLever

N Parking

Brake

N

Transmission

ReleaseLevers

GroundSpeedLevers- GroundSpeedLevers-

DRIVEPositons PARKPositons

CONTROL FUNCTIONS

Figure 1. Controls

The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing

require the combined use of several controls applied in specific sequences. To learn what combination and sequence

of controls to use for various tasks please read the entire section.

Ground Speed Levers

These levers control the ground speed of the rider. The

left lever controls the left rear drive wheel and the right

lever controls the right rear drive wheel.

Pushing the levers out, away from the operator's lap

locks them in PARK positions (inset, Figure 1). Pulling

the levers in across the operator's lap puts them in

DRIVE positions.

From DRIVE position, moving a lever forward increases

the FORWARD speed of the associated wheel. Pulling

back on a lever increases the REVERSE speed. The fur-

ther a lever is pushed, the faster the drive wheel will turn.

_ Throttle Control

The throttle controls engine speed. Always operate at

FULL throttle when mowing. Move the lever forward to

the detent for FULL throttle (FAST). Move the throttle

back to decrease engine speed to IDLE (SLOW).

Choke

Close the choke for cold starting. Open the choke once

the engine starts. A warm engine may not require chok-

ing. Move the lever forward past the FULL throttle detent

to close the choke. Move the lever back to the detent to

open the choke.

See the DRiViNG PRACTICE for steering instructions.

10

Mower Height of Cut Adjustment

To adjust cutting height, rotate the turn crank clockwise

to raise the mower deck and counterclockwise to lower

the mower deck.

ignition Switch

The ignition switch starts and stops the engine; it has

three positions:

OFF Stops the engine and shuts off the

electrical system.

RUN Allows the engine to run and powers the

electrical system.

START Cranks the engine for starting.

NOTE." Never leave the ignition switch in the RUN posi-

tion with the engine stopped. This drains the battery.

B Hour Meter

The hour meter measures the number of hours the key

has been in the RUN position. The hour meter will flash

an oil change indicator at 5 hours, and a lubrication

reminder every 50 hours. These reminders will automati-

cally reset themselves.

NOTE." The hour meter will register the passage of time

when the key is in the RUN position, even if the engine is

not running.

PTO Switch

The PTO (Power Take-Off) switch engages and disen-

gages an electric clutch attached to the engine crank-

shaft. This electric clutch drives and stops the mower

deck. To turn the mower on, pull the switch UP. Push the

switch DOWN to turn the mower off. Note that the opera-

tor must be seated firmly in the rider seat for the PTO to

function.

Transmission Release Levers

The transmission release levers deactivate the transmis-

sions so that the unit can be pushed by hand. See

PUSHING THE UNIT BY HAND for operational informa-

tion.

Seat Adjustment Knob

The seat can be adjusted forward and backward. Tip the

seat forward, loosen the adjustment knob, slide the seat

to the desired position, and tighten the knob.

Fuel Tank

To remove the cap, turn counterclockwise.

Parking Brake

DRIVE Releases the parking brake.

PARK Locks the parking brake.

Pull the parking brake lever up to engage the parking

brake (PARK position). Move the lever fully down to dis-

engage the parking brake (DRIVE position).

NOTE: Tostart the unit the parking brake must be in

PARK position.

GENERAL OPERATING SAFETY

Before first time operation:

• Be sure to read all information in the Safety and

Operation sections before attempting to operate this

rider and mower.

• Become familiar with all of the controls and how to stop

the unit.

• Drive in an open area without mowing to become accus-

tomed to driving the unit.

,WARNING

If you do not understand how a specific control

functions, or have not yet thoroughly read the

CONTROL FUNCTIONS section, do so now.

Do NOT attempt to operate the rider without first

becoming familiar with the location and function

of ALL controls.

11

CHECKS BEFORE STARTING

• Check that the crankcase oil is filled to full mark on

dipstick.

• Adjust the seat position and make certain you can

reach all controls.

Fill the fuel tank with fresh fuel.

FUEL RECOMMENDATIONS

For daily operation: Use only unleaded gasoline with a

pump sticker octane rating of 87 or higher. Gasohol (up

to 10% ethyl alcohol, 90% unleaded gasoline by volume)

is approved as a fuel. Methyl Teriary Butyl Ether (MTBE)

and unleaded gasoline blends (up to a maximum of 15%

MTBE by volume) are approved as a fuel. No other gaso-

line/alcohol or gasoline/ether blends are approved. Do

not use fuel additives other than fuel stabilizer.

For storage: CAUTION: Alcohol blended fuels (called

gasohol or using ethanol or methanol) can attract mois-

ture which leads to separation and formation of acids

during storage. Acidic gas can damage the fuel system

of an engine while in storage.

To avoid engine problems, the fuel system should be

emptied before storage of 30 days or longer. Drain the

gas tank, start the engine, and let it run until the fuel

lines and carburetor are empty (see STORAGE for fuel

draining procedure). Use fresh fuel next season. See

STORAGE instructionsfor additional information.

Never use engine or carburetor cleaner products in the

fuel tank or permanent damage may occur. To add fuel:

1. Remove the fuel cap (B, Figure 2).

2. Fill the tank. Do not overfill. Leave room in the tank

for fuel expansion.

3. Install and hand tighten the fuel cap.

tLWARNING

Never allow passengers to ride on the unit.

Before leaving the operator's position for any

reason, engage the parking brake, disengage the

PTO, stop the engine and remove the key.

To reduce fire hazard, keep the engine, rider and

mower free of grass, leaves and excess grease.

Do not stop or park rider over dry leaves, grass or

combustible materials.

Gasoline is highly flammable and must be

handled with care. Never fill the tank when the

engine is still hot from recent operation. Do not

allow open flame, smoking or matches in the area.

Avoid over=filling and wipe up any spills.

Figure 2. Pre=Start Checks

A. Seat Adjustment Knob

B. Fuel Tank Cap

WARNING

Never operate on slopes greater than 17.6 percent

(10 °) which is a rise of 3=1/2 feet (106 cm)

vertically in 20 feet (607 cm) horizontally.

Select slow ground speed before driving onto a

slope. Use extra caution when operating on

slopes with a rear=mounted grass catcher.

Mow UP and DOWN the slope, never across the

face. Use caution when changing directions and

DO NOT START OR STOP ON A SLOPE.

WARNING - TRAILERS

Do not load this zero-turn rider on a trailer or

truck using two separate ramps. Only use a

single ramp that is at least one foot wider than

the width of the rear wheels of this rider. This

rider has a zero turning radius and the wheels

could fall off the ramps, or the rider could tip over

injuring the operator or bystanders.

12

EMERGENCY STOPPING

In the event of an emergency the engine can be stopped

by simply turning the ignition switch to STOR Use this

method only in emergency situations. For normal engine

shut down follow the procedure given in STOPPING THE

RIDER AND ENGINE.

STOPPING THE RIDER & ENGINE

1. Returning the ground speed control levers to PARK

positions will stop rider movement.

2. Stop the mower by pushing down on the PTO switch.

3. Move the parking brake lever to PARK position.

4. Move the throttle control to FAST position and turn

the ignition key to OFR Remove the key.

STARTING THE ENGINE

1. While sitting in the operator's seat, set the parking

brake to PARK. Make sure the PTO switch is OFF

and the ground speed control levers are locked in

PARK positions.

2. Move the engine throttle control fully forward to

CHOKE.

NOTE: A warm engine may not require choking. In this

case, set the throttle control to FAST

3. Insert the key into the ignitionswitch and turn it to

START.

4. After the engine starts, gradually move the throttle

control back to FAST position (choke open). Warm

the engine by running it for at least a minute before

turning on the PTO switch, or driving the unit.

5. After warming the engine, ALWAYS operate the

unit with the throttle set to FAST position when

mowing.

MOWING

1. Place the parking brake lever in PARK position. Make

sure the PTO switch is OFF, the ground speed control

levers are locked in their PARK positions, and the

operator is in the seat.

2. Set the mower cutting height to the desired setting.

3. Start the engine (see STARTING THE ENGINE).

4. Set the throttle to FAST.

5. Turn the PTO switch ON to engage the mower deck.

6. Move the parking brake lever to DRIVE position.

7. Move the ground speed control levers from PARK

positions to drive positions (levers in across the oper-

ator's lap).

8. Begin mowing. See DRIVING PRACTICE.

9. When finished, turn the PTO switch OFR

10. Stop the engine (see STOPPING THE RIDER AND

ENGINE).

PUSHING THE RIDER BY HAND

1. Turn the PTO switch OFF, set the parking brake to

PARK, turn the ignition switch OFF, remove the key,

and wait for all moving parts to stop.

2. Locate the transmission release levers (A & B, Figure

3) at the rear of the unit.

3. Pull both levers back and down to release the trans-

missions (position B, Figure 3).

4. Set the parking brake to DRIVE.

The rider can now be pushed by hand.

5. After moving the rider, set the parking brake to PARK

and move the transmission release levers up and in

to re-engage the transmissions (position A, Figure 3).

DO NOTTOW RIDER

Towing the unit will cause transmission dam-

age. Do not use another vehicle to push or

pull this unit.

Figure 3. Transmission Release Levers

A. Drive Position

B. Push Position

13

DRiViNG PRACTICE-

BASIC DRIVING

WARNING: Never operate on slopes greater than 17.6%

(10°). See SLOPE OPERATION in the safety section.

Zero turn riders operate differently from other bur-

wheeled vehicles. The drive wheels are also your steer-

ing wheels. If you cannot drive the unit on a hill, you will

not be able to steer the unit on it. Operating zero turn

units on slopes requires extra caution.

The lever controls of the zero turn rider are very respon-

sive, and learning to gain a smooth and efficient control

of the rider's forward, reverse, and turning movements

will take some practice.

Spend some time going through the following maneuvers

and becoming familiar with how the unit accelerates,

travels, and steers -- before you begin mowing --is

absolutely essential to getting the most out of the zero

turn rider.

Locate a smooth, fiat area of your lawn -- one with

plenty of room to maneuver. (Clear the area of objects,

people and animals before you begin.) Operate the unit

at mid-throttle during this practice session (ALWAYS

operate at full throttle when mowing), and turn slowly to

prevent tire slippage and damage to your lawn.

We suggest you begin with the Smooth Travel procedure

to the right, and then advance through the forward,

reverse, and turning maneuvers.

You must set the parking brake to DRIVE prior to moving

the control levers out of park position.

WARNING

Do not mow in reverse unless absolutely

necessary. Always look down and behind before

and while travelling in reverse.

Forward Travel

Smooth Travel

The lever controls of the

zero turn rider are

highly responsive.

The BEST method of

handling the ground

speed control levers is in

three steps -- as shown

in Figure 4.

FIRST place your hands

onto the levers as

shown.

SECOND, to go forward

gradually push the levers

forward with your palms.

THIRD, to speed up

move the levers farther

forward. To slow down

smoothly, slowly move

the levers back toward

neutral.

Figure 4. Move Control

Levers Gradually

Forward Travel Practice

Gradually move both ground speed control levers evenly

FORWARD from neutral. Slow down and repeat.

Reverse Travel Practice

LOOK DOWN & BEHIND, then gradually move both

ground speed control levers evenly BACK from neutral.

Slow down and repeat.

NOTE: Practice backing up for several minutes before

attempting to do so near objects. The rider turns as

sharply in reverse as when going forward, and backing

up straight takes practice.

Reverse Travel

Figure 5. Forward Travel Figure 6. Reverse Travel

14

Practice Turning Around a Corner

While traveling forward allow one handle to gradually

return back toward neutral. Practice several times before

mowing.

NOTE." Toprevent piveting directly on the tire tread, it is

best to keep both wheels going at least slightly forward.

Practice Turning in Place

To "zero turn" means to turn in place. To turn in place,

gradually move one ground speed control lever forward

from neutral and one lever back from neutral simultane-

ously. Repeat several times.

Executing Turns

Turning In Place

Figure 7. RightTurn Figure 8. Turning in Place

ADVANCED DRIVING

Executing an End=Of=Row Zero

Turn

Your zero turn rider's unique ability to turn in

place allows you to turn around at the end of

a cutting row rather than having to stop and

make a Y-turn before starting a new row.

For example, to execute a right end-of row

zero turn:

1. Slow down at the end of the row.

2. Move the LEFT ground speed control

lever forward slightly while moving the

RIGHT ground speed control lever back to

center and then slightly back from center.

3. Begin mowing forward again.

This technique turns the rider RIGHT and

slightly overlaps the row just cut --eliminating

the need to back up and re-cut missed grass.

As you become more familiar and experi-

enced with operating the zero turn rider, you

will learn more maneuvers that will make your

mowing time easier and more enjoyable.

Remember, the more you practice, the bet=

ter your control of the rider will be!

Figure 9. Executing an End-Of-RowTurn

15

MOWER DECK REMOVAL &

INSTALLATION

NOTE: Perform mower removal and installation on a

hard, level surface such as a concrete floor.

WARNING

Engage parking brake, disengage PTO, stop

engine and remove key before attempting to

install or remove the mower.

Removing the Mower Deck

1. Turn the PTO off, set the parking brake to PARK, turn

the ignition OFF, remove the key, and wait for all mov-

ing parts to stop.

2. Pivot the rider's front wheels forward.

3. Place the cutting height adjustment crank (D, Figure

10) in the lowest cutting position.

4. Release tension on the drive belt using the mower

belt release lever (E, Figure 10) and remove the drive

belt from the engine pulley.

5. Disconnect the front hitch by removing the hitch rod

and clip (A, Figures 10 & 11), and lifting the mower

hitch (B) up and off the rider hitch bracket (D).

6. Slide the mower deck forward until the rear mower

supports (C) disengage the frame of the rider.

7. Slide the mower deck out from under the right side of

the rider.

Installing the Mower Deck

1. Pivot the rider's front wheels forward.

2. Place the cutting height adjustment crank (D, Figure 10)

in the lowest cutting position.

3. Slide the mower deck under the right side of the rider.

Slide the mower backwards making sure that the rear

mower supports (C, Figure 11) slide up the ramps on

the frame. The rear of the mower is supported by

these frame ramps.

4. Hang the mower hitch (B, Figure 11) on the rider

hitch bracket (D) and secure with the hitch rod and

clip (A).

5. Use the mower belt release lever (E, Figure 12) to

release tension on the mower idler pulley, and install

the drive belt as shown in Figure 12.

Figure 10. Mower Components

A. Hitch Rod and Clip

B. Mower Hitch

C. Rear Mower Supports

D. Cutting Height Adjustment Crank

E. Mower Belt Release Lever

Figure 11. Mower Hitch Components

A. Hitch Rod and Clip

B. Mower Hitch

C. Rear Mower Supports

D. Rider Hitch Bracket

Figure 12. Mower Belt Routing

A. Engine Pulley

B. Mower Drive Belt

C. Back=Side Idler Pulley

D. V=ldler Pulley

E. Mower Belt Release Lever

F. Mower Drive Pulley

16

MAINTENANCE SCHEDULE

The following schedule should be followed for normal care of your rider and mower. You will need to keep a record of

your operating time. Determining operating time is easily accomplished by observing the elapsed time recorded by

the hour meter.

RIDER MAINTENANCE Before Every Spring 8 25 100 200

ITEMS Each Use & Fall Hours Hours Hours Hours

Clean Debris from Rider and Engine =

Compartment *

Clean Debris from Engine Cooling Areas ®

& Air Filter *

Check Tire Pressure •

Lubricate Rider & Mower * ®

Clean Deck & Check/Replace Mower •

Blades

Clean Battery & Cables ®

Check Rider Safety System ** • •

Check / Adjust PTO Clutch •

ENGINE MAINTENANCE ITEMS

Check Engine Oil Level • •

Service Air Filter Pre-Cleaner * ®

Replace Air Filter *

Change Engine Oil *

Replace Spark Plug

Replace Fuel Filter

Change Engine Oil & Filter *

• More often in hot (over 85 ° F: 30° C) weather or dusty operating conditions.

•* Check the function of the safety system after the unit has been stored for 30 days or longer.

o

®

o

®

17

Rider Maintenance items

CLEAN DEBRIS FROM RIDER AND

ENGINE COMPARTMENT

Service IntervaJ: Before each use.

CAUTION: if debris is not removed from the engine

compartment and other hot surfaces, it creates a fire

hazard. Before starting the unit at the beginning of the

mowing session, remove any grass clippings, dirt,

leaves, or other debris from the unit. Also clean out the

engine compartment.

CLEAN DEBRIS FROM ENGINE

COOLING AREAS AND AIR FILTER

Service Interval: Before each use.

CAUTION: if debris is not removed from the engine

compartment and other hot surfaces, it creates a fire

hazard. Before starting the unit at the beginning of the

mowing session, lift the seat deck and clean any debris

from the intake screen on top of the engine (A, Figure

13), exposed engine cooling fins, and around the air filter

assembly. Also open the air filter cover (B) and remove

any debris that has accumulated in the air filter compart-

ment.

CHECKTIRE PRESSURE

Service Interval: 25 Hours.

Tire pressure should be checked periodically, and main-

tained at the levels shown in Figure 14. Note that these

pressures may differ slightly from the "Max Inflation"

stamped on the side-wall of the tires. The pressures

shown provide proper traction, improve cut quality, and

extend tire life.

Figure 13. Engine Compartment

A. intake Screen

B. Air Filter Cover

Tire Pressure

Front 18-20 psi (1,24-1,38 bar)

Rear 10-12 psi (,69-,83 bar)

Figure 14. Tire Pressures

18

LUBRiCATiON

Service Interval: 25 hours.

Lubricate the unit at the locations shown in Figures 15

through 17 as well as the following lubrication points.

Grease:

r_ . front wheel grease fittings

• front wheel bushings

• mower pivots

• mower arbors

Use grease fittings when present.

Not all greases are compatible. Use automotive-type lithi-

um grease.

Oil:

,L

rear frame assembly pivot

• hydro linkage

• seat adjustment assembly

• brake linkage

frame pivot points

• mower deck height adjustment linkage

Generally, all moving metal parts should be oiled where

contact is made with other parts. Keep oil and grease off

belts and pulleys. Remember to wipe fittings and sur-

faces clean both before and after lubrication.

Figure 16. Lubricating Rider

/

Figure 15. Mower Lubrication

Figure 17. Arbor Lubrication

19

CLEAN DECK &

CHECK / REPLACE MOWER BLADES

Service Intervah 25 hours or as required.

WARNING

For your personal safety, do not handle the sharp

mower blades with bare hands. Careless or

improper handling of blades may result in serious

injury.

WARNING

For your personal safety, blade mounting

capscrews must each be installed with a

hex/spline washer and spring washer, then

securely tightened. Torque blade mounting

capscrew to 45 - 55 ft. Ibs. (61 - 75 N.m.)

1. Remove mower deck (see "Mower Deck Removal" in

the OPERATION section).

2. See Figure 18. Remove blade to inspect it or to safe-

ly access the underside of the mower deck. Use a

block of wood to prevent blade rotation while loosen-

ing the capscrew by turning it counterclockwise.

3. Remove the capscrew (D, Figure 20), spring washer

(C), hex washer (B), and blade.

4. Clean the underside of the mower deck.

5. Inspect the blades for nicks or dull edges. Use a file

to sharpen blade to a fine edge. If the blade is dam-

aged, it must be replaced.

6. Balance the blade as shown in Figure 19. Center the

blade's hole on a nail lubricated with a drop of oil. A

balanced blade will remain level. If the blade is not

balanced, continue to sharpen the heavy side until it

balances.

7. Reinstall the blade with the lift wings (E, Figure 20)

pointing up toward the mower deck as shown.

8. Reinstall the hex washer (B, Figure 20), spring wash-

er (C) and capscrew (D). Use a wooden block (A) to

prevent blade rotation while tightening the capscrew

(D) to 45-55 ft. Ibs. (61-75 N.m). Turn capscrew

clockwise to tighten.

Figure 18. Blade Removal

Workbench

Figure 19. Balancing The Blade

Figure 20. Blade installation

A. 4x4 Wood Block

B. Hex Washer

C. Spring Washer

D. Blade Capscrew

E. Lift Wings

J

LOOSEN

Nail

2O

Page is loading ...

Craftsman ZT Zero 22 User manual

This manual is also suitable for

Craftsman ZT Zero 22 User manual

in other languages

Related papers

Other documents