NEC 200 User manual

MultiSync LCD200

User’s Manual

Declaration of the Importer

We hereby certify that the

Color monitor LA-1221JMW

MultiSync LCD

200

is in compliance with

Council Directive 73/23/EEC:

- EN 60950

Council Directive 89/336/EEC:

- EN 55022

- EN 60555-2

- EN 60555-3

- EN 50082-1

(IEC 801-2)

(IEC 801-3)

(IEC 801-4)

and marked with

NEC Europe Ltd. Ismaning Office

Steinheilstraße 4-6

D-85737 Ismaning, Germany

Safety Instruction

Caution:

When operating the LA-1221JMW with a 220-240V AC power source

in Europe except UK, use the power cord provided with the monitor.

In UK, a BS approved power cord with moulded plug has a Black (five

Amps) fuse installed for use with this equipment. If a power cord is not

supplied with this equipment please contact your supplier.

When operating the LA-1221JMW with a 220-240V AC Power source

in Australia, use the power cord provided with the monitor.

For all other cases, use a power cord that matches the AC voltage of the

power outlet and has been approved by and complies with the safety

standard of your particular country.

IBM PC/XT/AT, PS/2, MCGA, VGA, 8514/A and XGA are registered trademarks of

International Business Machines Corporation.

Apple and Macintosh are registered trademarks of Apple Computer Inc.

Microsoft and Windows are registered trademarks of the Microsoft Corporation.

NEC is a registered trademark of NEC Corporation. ErgoDesign, IPM, OSM, ColorControl,

OptiClear, C

ROMACLEAR and Advanced Digital Control System are trademarks of NEC Home

Electronics, Ltd.

MultiSync is a registered trademark of NEC Technologies, Inc in U.S., and of NEC Home

Electronics, Ltd in Canada, U.K., Germany, France, Spain, Italy, Austria, Benelux,

Switzerland, Denmark, Finland, Norway and Saudi Arabia.

All other trademarks or registered trademarks are property of their respective owners.

English

Deutsch

Français

Italiano

Español

Appendix

English

Introduction to the NEC MultiSync LCD200

Congratulations on your purchase of the NEC MultiSync LCD

200 true

color monitor!

True Color Monitor

The MultiSync LCD200 monitor incorporates NEC’s own l2.1" true

color active matrix thin-film-transistor (TFT) liquid crystal display to

provide superior display performance and a reduced footprint. Less than

18 cm in depth, the MultiSync LCD

200 monitor is ideal for

environments with space and weight constraints that require superior

image quality. A high resolution of 1024 x768 and a fine dot pitch of

0.24mm are ideal for displaying complex graphics and high definition

images. The MultiSync LCD

200 monitor also supports 800 x 600 and

VGA graphics and text modes. Other examples of features that enhance

the MultiSync LCD

200 monitor’s performance are Microsoft’s Plug and

Play compatibility, NEC’s ErgoDesign features and OSM (On Screen

Manager) controls. This LCD monitor also carries the MultiSync brand

name, ensuring greater compatibility with today’s sophisticated

computer platforms.

Analog Advantage

Because NEC incorporates only its own patented analog LCD modules

into its MultiSync LCD monitors, the MultiSync LCD

200 monitor is

capable of displaying over 16.7 million colors in a continuous spectrum,

providing a truer representation of color. Like its analog predecessors

based on CRT technology, the MultiSync LCD

200 monitor displays a

continuous gray scale and does not require the use of dithering

techniques, a mainstay of digital LCD panels, to approximate

intermediate shades of gray. In addition, the monitor’s high contrast

LCD enhances color vibrancy and improves focus with no geometric

distortion.

Introduction to the NEC MultiSync LCD200 E- 1

Wider Compatibility

Adapting the latest advances in satellite technology to the circuitry

employed within the MultiSync LCD

200 monitor, NEC provides wide

range compatibility with today’s graphics driver technology. Because

the MultiSync LCD

200 monitor is analog through and through, it does

not require special analog to digital display or interface cards but can

accept RGB input directly. Consequently, the same display cards that

are used to drive the Multisync LCD200 monitor can also be used to

drive standard CRT monitors. NEC’s MultiSync LCD

200 monitor can

be used with a wide range of systems such as IBM PC compatible

computers, Macintosh and Power Macintosh.

FullScan Capability

Using NEC’s own FullScan Capability, all of the resolutions supported

on the MultiSync LCD

200 monitor are displayed full screen, utilizing

the most of the monitor’s large display area. Rather than displaying

640x480 resolution as a small box in the center of the MultiSync

LCD

200 monitor’s display, this VGA resolution is displayed full screen,

allowing for greater visibility.

Reduced Footprint

The MultiSync LCD200 monitor offers nearly the same viewable image

size as conventional 14-inch and 15-inch CRTs at 40% of the depth and

30% of the weight. With a depth of about 17 cm and a weight of 4 kg,

the reduced footprint of NEC’s MultiSync LCD monitor provides the

ideal solution for environments requiring superior image quality but

with size and weight limitations. And the monitor’s small footprint and

low weight allow it to be moved or transported easily from one location

to another.

Low Power Consumption

The MultiSync LCD200 monitor has been designed with NEC’s IPM

(Intelligent Power Manager) System. When utilized with an Energy

Star system or display card, the MultiSync LCD

200’s IPM System is an

innovative power-saving utilily that complies with both the EPA’s

Energy Star requirements and Europe’s NUTEK power management

E - 2 Introduction to the NEC MultiSync LCD200

requirements. With a maximum power consumption of 33 watts, the

MultiSync LCD

200 monitor consumes over 50% less power than

conventional CRTs and emits less heat. In its power-saving mode, the

MultiSync LCD

200 monitor consumes less than 6 watts. All this

translates into energy savings, environmental protection, reduced

emissions and reduced air conditioning costs of the work environment.

The MultiSync LCD

200 monitor follows the Video Electronics Standard

Association (VESA) approved power-down signaling method. Endorsed

by the EPA, VESA’s Display Power Management Signaling (DPMS)

method is the power-down process a system should use to communicate

to the monitor to save power. Power-down functions can be utilized

only with an Energy Star system or display card which adheres to the

VESA DPMS standard. By using the monitor’s horizontal and vertical

SYNC signals, the monitor can be prompted into the different IPM

modes. The following is the description of the LED indicator for the

IPM power-saving modes:

Mode LED Indicator Power Consumption

ON Green Typical: 33 watts

Standby & Suspend Amber Typical: About 6 watts

Power Switch OFF No Light No Power Used

Plug and Play

Plug and Play is the new Microsoft solution with Windows 95 to

provide automatic peripheral connections without confusing and

time-consuming setup. NEC developed the monitor’s Plug and Play

capability that allows your Plug and Play compatible system to

automatically identify, configure and optimize the monitor connected to

it. The MultiSync LCD

200 monitor automatically tells the system its

identification and capabilities. NEC’s partnership with Microsoft

provides you with simple installation, setup and service.

Introduction to the NEC MultiSync LCD200 E- 3

ErgoDesign Features

The MultiSync LCD200 monitor utilizes NEC’s ErgoDesign features

philosophy that adapts technology to the way you work, increasing

productivity through enhancements in comfort and ease of use.

ErgoDesign features include a low glare screen treatment, power and

brightness controls that are positioned within easy reach, easy-to-use

on-screen controls and a tilt base that easily adjusts to each individual’s

preferred angle of vision.

Reduced Emissions

Incorporating NEC’s own Reduced Magnetic Field technology, the

MultiSync LCD

200 monitor has minimal field emissions and follows the

strictest international magnetic field, alternating electric field and

electrostatic guidelines.

OSM (On-Screen Manager) Controls

The OSM (On-Screen Manager) controls simplify the MultiSync’s

Advanced Digital Control System. The control system is easily

accessed. Just touch the PROCEED button on the front of the monitor,

which gives you access to the Position, Image Adjust and Contrast

controls, the ColorControl System and many others. Use the front

controls for navigation.

Position

Image Adjust

Contrast

AccuColor

OSM Location

OSM Turn Off Time

OSM Lock Out

ON SCREEN MANAGER

E - 4 Introduction to the NEC MultiSync LCD200

Through the OSM control’s enhanced ColorControl System, you can

better match your image color to a variety of standards such as:

– Your personal preference (depending upon the application

used).

– A color standard such as Pantone or Trumatch.

– Another monitor.

– Your printer or Service Bureau output.

Additional OSM controls are available such as OSM Location, OSM

Turn Off Time, OSM Lock Out, Display Mode, Language Select and

Factory Preset.

Introduction to the NEC MultiSync LCD200 E- 5

Contents of Package

Included with your MultiSync LCD200 monitor are the following items:

– NEC MultiSync LCD200 (Model LA-122lJMW) true color

monitor.

– AC power cable.

– Video signal cable (15 pin mini D-sub male to 15 pin mini

D-sub male).

– User’s manual.

Remember to save the original box and packing materials to transport or

ship this monitor.

E - 6 Contents of Package

Recommended Use

For optimum performance, please note the following when setting up

and using the MultiSync LCD

200 color monitor:

• The optimum monitor position is facing away from direct

sunlight.

• Allow adequate ventilation around the monitor so that heat

can properly dissipate.

• Do not place any heavy objects on the power cord. Damage

to the cord may cause shock or fire.

• Use the monitor in a clean and dry area.

• Handle with care when transporting. Save packaging for

transporting.

• When operating the MultiSync LCD200 with its AC125-

240V worldwide power supply, use a power supply cord

that matches the power supply voltage of the AC power

outlet being used. The power supply cord you use shall be

employed one of the type H05VV-F with the earth pin,

which must have been approved by and comply with the

safety standards of your country.

• The power cable connector is the primary means of detaching

the system from the power supply. The monitor should be in-

stalled close to a power outlet which is easily accessible.

• Clean the LCD monitor surface with a lint-free, non-abrasive

cloth. Avoid using any cleaning solution, glass cleaner or tis-

sue paper.

• For optimum performance, allow 20 minutes for warm-up.

• Avoid displaying fixed patterns on the monitor for extremely

long periods of the time to avoid after-image effects.

• Avoid applying pressure to the LCD monitor surface.

Recommended Use E - 7

Installation

Connection to your Personal Computer

(NEC and PC Compatibles)

The MultiSync LCD200 true color monitor complements NEC and PC

compatible computers. Your system has one of two configurations:

– the video controller is built into the computer.

– the video controller is in the form of a display card (sometimes

referred to as graphics card, video adapter or graphics board).

Both configurations have a video connector (or a CRT PORT on laptop

computers). If you are not sure which connector is the video connector,

refer to your computer or display card manual.

To attach the monitor to your system, follow these instructions:

1. Turn off the power to the monitor and computer.

2. If necessary, install the display card. For more information

about installing your card, refer to the display card manual.

3. Connect the MultiSync LCD

200 monitor’s video cable to the

display card’s connector.

4. Connect one end of the power cable to the MultiSync monitor

and the other end to the power outlet.

5. Turn on the monitor and the computer.

6. This completes the installation.

If you have any problems, please refer to the Troubleshooting section of

this manual.

E - 8 Installation

Connection to your Personal Computer (Macintosh)

With the Macintosh cable adapter, the MultiSync LCD200 color monitor

is compatible with the Macintosh family of computers, Power

Macintosh, Mac Quadra Series, Mac Centris Series, Mac LC series,

Mac Performa series, PowerBooks and other NuBus/PCI display cards

@ 640x480, 800x600, and 1024x768 resolutions.

You will connect your MultiSync color monitor one of two ways to

your Macintosh computer:

– On-board video port

– NuBus/PCI/PDS display card

Both configurations should have the same style video connector. If you

are not sure which port is the monitor connector, please reference your

computer or display card manual.

To attach the monitor to your system, follow these instructions:

1. Turn off the power to your MultiSync monitor and Macintosh.

2. If necessary, install the display card. For more information on

this installation, reference the display card manual.

3. If necessary, install the 15-pin to 15-pin MultiSync LCD

200

Macintosh cable adapter to the monitor connector. Tighten the

screws.

4. Connect the MultiSync monitor’s signal cable to the other end

of the cable adapter. Tighten the screws between the signal

cable and cable adapter to ensure proper connection.

5. Connect one end of the power cable to the MultiSync monitor

and the other end to the power outlet.

6. If you have a Powerbook, Mac LC, Mac AV, Power Mac or

Quadra 605 or 630 or are running system 7.5, please make sure

the SYNC switch is in the ON position. (The SYNC switch is

located on the back of the monitor). All other Mac systems

require the SYNC switch to be in the OFF position.

7. Turn on the monitor and the computer.

Installation E - 9

8. This completes the installation.

Power Macintosh 6100/60 and 66 users need to use the Apple HDI-45

cable adapter and Powerbook users need to use the Apple VID-14 cable

adapter in conjunction with the appropriate MultiSync Macintosh cable

adapter when connecting a MultiSync monitor.

Connection to Other Computers or Display Cards

If your computer or display card is not compatible with the MultiSync

LCD

200 color monitor’s PRESET signals or has a different pin

assignment, refer to the steps below to determine if your system is

compatible with the MultiSync LCD

200 color monitor.

1. Determine the video connector’s pin assignments of your

display card.

2. Determine the output signal timing and level of your display card.

3. Check the pin assignment and signal timing charts of the display

card and make sure the monitor accepts these pin assignments

and signal timings.

4. Select the appropriate SYNC switch setting on the rear of the

monitor according to your computer or display card output.

SYNC switch should be set in the ON position for standard

separate or composite Sync mode and in the OFF position for

Sync on Green priority mode.

5. Connect the signal cable supplied with your display card to the

monitor.

6. Connect one end of the power cable to the MultiSync LCD

200

monitor and the other end to the power outlet.

7. Turn on the monitor and the computer.

8. Adjust the position of the image to your preference.

9. This completes the installation.

If you have any problems, please refer to the Troubleshooting section of

this manual.

E - 10 Installation

Controls

Direct Controls

EXIT: Has no function

SETTING ▼/▲: Selects between two sets of parameters for each

resolution. Each selection can be preset by adjusting the OSM controls

to your preference. Changes are saved automatically.

LCD Brightness -/+: Adjusts the overall image and background screen

brightness.

PROCEED: Accesses OSM controls menu

RESET: Has no function

LED Power Indicator Light: Located on the lower right and indicates

the monitor’s power mode. Each mode reduces the amount of power

used by the monitor.

Mode LED Indicator Power Consumption

ON Green Typical: 33 watts

Standby & Suspend Amber Typical: About 6 watts

Power Switch OFF No Light No Power Used

Power Switch: Located on the right side of the monitor’s base which

turns the monitor power on or off. When the power is on, the LED is lit.

SYNC Switch: Located on the rear of the monitor, which allows

selection between standard separate and composite Sync modes (ON)

and Sync on Green priority mode (OFF).

Controls E - 11

OSM Controls

The OSM controls on the front of the monitor provide the following

functions:

Control In the Main Menu In the Sub Menu

EXIT ▼/▲ Exits the OSM controls. Exits to the OSM

controls menu.

SETTING Moves the highlighted

area up/down to select

one of the controls.

Moves the highlighted

area up/down to select

one of the controls

SETTING -/+ Has no function. Moves the bar in the +

or - direction to increase

or decrease the

adjustment.

PROCEED Proceeds to selected

menu choice (indicated

by the highlighted area).

Proceeds to the control

in that sub menu.

RESET: The currently

highlighted control to

the factory setting.

Resets all the controls

within the highlighted

menu.

Resets the highlighted

control.

NOTE: When RESET is pressed, a warning window will appear

allowing you to cancel the reset function.

WARNING

ABOUT TO RESET

POSITION

Press:

PROCEED-Reset

EXIT-Cancel

E - 12 Controls

OSM Control Elements

Typical On Screen Manager windows have the following elements:

Control Function

Highlight Indicates the selected menu or Control

Scroll Bar Indicates direction of adjustment

Numeric Reading Provides a number to remember, record or compare a

specific setting.

OSM Control Menus

Main Menu

The arrow in the bottom or upper right corner indicates that further

choices are available. Use the ▼/▲ control buttons to scroll through all

of the options.

ON SCREEN MANAGER

Position

Image Adjust

Contrast

AccuColor

OSM Location

OSM Turn Off Time

OSM Lock Out

OSM Control Menus E - 13

Position Menu

Up/Down: Moves the image vertically up or down.

Left/Right: Moves the image horizontally left or right.

Image Adjust

Adjust the horizontal size of the image by increasing or decreasing the

coarse total. Focus, clarity and image stability can be improved by

increasing or decreasing the Fine total.

Position

Up

Right

Down

Left

Image Adjust

1280

31

Coarse

Fine

E - 14 OSM Control Menus

Contrast

The contrast level of the monitor’s display can be adjusted by increasing

or decreasing the total.

AccuColor Control System Menu

Preset(Setting): Selects the desired color setting. The bar is replaced by

the color setting choice (from 1 to 3). Each color setting is adjusted at

the factory to the stated degree Kelvin. If a setting is adjusted, the name

of the setting will change from degree Kelvin to Custom.

Color Gain: Increases or decreases red, green or blue depending upon

which is selected. The change in color will appear on screen and the

direction (increase or decrease) will be shown by the color bars. One

Contrast

100

AccuColor

Preset: 6600 Kelvin

123

Color Gain:

100

Red

Green

Blue

OSM Control Menus E - 15

Page is loading ...

NEC 200 User manual

This manual is also suitable for

NEC 200 User manual

in other languages

Related papers

Other documents