GE GFDN245ELMS User manual

Brand: GE

Model: GFDN245ELMS

Category: Tumble dryers

Type: User manual

Safety Instructions . . . . . . . . 2–5

Operating Instructions

Control Panels . . . . . . . . . . . . . . . . 6–8

Cycle Options . . . . . . . . . . . . . . . . . 9-10

Dryer Features . . . . . . . . . . . . . . . . . . 10

Reversing the Door Swing . . . .11-14

Loading and Using

the Dryer . . . . . . . . . . . . . . . . . . . . . 15-16

Venting the Dryer . . . . . . . . . . . . . . . 17

Connecting Inlet Hoses . . . . . . . . . . 18

Stacking . . . . . . . . . . . . . . . . . . . . .19-22

Troubleshooting Tips . . . .23-26

Consumer Support

Warranty . . . . . . . . . . . . . . . . . . . . . . . 27

Consumer Support . . . . . . . . . . . . . . 28

49-90394 05/14/10 GE

234D1050P001

GEAppliances.com

GFDS350

GFDS355

GFDN240

GFDN245

Owner’s Manual

Dryers

Write the model and serial

numbers here:

Model # _____________

Serial # ______________

They are on the label on

the front of the dryer behind

the door.

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

California Safe Drinking Water and Toxic Enforcement Act

This act requires the governor of California to publish a list of substances known to the state to cause cancer,

birth defects or other reproductive harm and requires businesses to warn customers of potential exposure

to such substances.

Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide,

formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.

Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be minimized

further by properly venting the dryer to the outdoors.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk

of fire or explosion, electric shock, or to prevent property damage, personal injury, or

death.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light a match, or cigarette,

or turn on any gas or electrical

appliance.

Do not touch any electrical switch;

do not use any phone in your building.

Clear the room, building or area of all

occupants.

Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions carefully.

If you cannot reach your gas supplier,

call the fire department.

n Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

n Installation and service must be

performed by a qualified installer,

service agency or the gas supplier.

n Properly ground dryer to conform with all

governing codes and ordinances. Follow details

in Installation Instructions.

n Install or store where it will not be exposed

to temperatures below freezing or exposed

to the weather.

n Connect to a properly rated, protected and sized

power supply circuit to avoid electrical overload.

n Remove the colored protective film from both

the control panel and the door.

n Remove all sharp packing items and dispose

of all shipping materials properly.

n Do not remove the vent protector from the back

of the dryer (on some models).

n Pull the protector out and down to its lowest

position and connect the exhaust duct to the dryer.

The lowered protector will prevent the duct from

getting crushed (on some models).

Exhaust/Ducting:

Dryers MUST be exhausted to the outside to

prevent large amounts of moisture and lint from

being blown into the room.

Use only rigid metal 4″ diameter ductwork inside

the dryer cabinet and use only UL approved

transition ducting between the dryer and the

home duct. USE OF PLASTIC OR OTHER

COMBUSTIBLE DUCTWORK CAN CAUSE A FIRE.

PUNCTURED DUCTWORK CAN CAUSE A FIRE IF

IT COLLAPSES OR BECOMES OTHERWISE

RESTRICTED IN USE OR DURING INSTALLATION.

For complete details, follow the Installation

Instructions.

PROPER INSTALLATION

This dryer must be properly installed and located in accordance with the Installation Instructions

before it is used. If you did not receive an Installation Instructions sheet, you can receive one by

visiting GEAppliances.com, or by calling 800.GE.CARES (800.432.2737).

GEAppliances.com

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

YOUR LAUNDRY AREA

n Keep the area underneath and around your

appliances free of combustible materials

(lint, paper, rags, etc.), gasoline, chemicals

and other flammable vapors and liquids.

n Keep the floor around your appliances clean

and dry to reduce the possibility of slipping.

n Close supervision is necessary if this appliance

is used by or near children. Do not allow children to

play on, with or inside this or any other appliance.

n Keep all laundry aids (such as detergents,

bleaches, etc.) out of the reach of children,

preferably in a locked cabinet. Observe all warnings

on container labels to avoid injury.

n Never climb on or stand on the dryer top.

n Keep the area around the exhaust opening

and adjacent surrounding areas free from the

accumulation of lint, dust and dirt.

WHEN USING YOUR DRYER

n Never reach into the dryer while the drum is

moving. Before loading, unloading or adding

clothes, wait until the drum has completely

stopped.

n Clean the lint filter before each load to prevent lint

accumulation inside the dryer or in the room.

DO NOT OPERATE THE DRYER WITHOUT

THE LINT FILTER IN PLACE.

n Do not wash or dry articles that have been

cleaned in, washed in, soaked in or spotted

with combustible or explosive substances

(such as wax, oil, paint, gasoline, degreasers,

dry-cleaning solvents, kerosene, etc.) which may

ignite or explode. Do not add these substances

to the wash water. Do not use or place these

substances around your washer or dryer during

operation.

n Do not place items exposed to cooking oils in your

dryer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause

a clothes load to catch fire

n Any article on which you have used a cleaning

solvent or that contains flammable materials

(such as cleaning cloths, mops, towels used in

beauty salons, restaurants or barber shops,

etc.) must not be placed in or near the dryer

until solvents or flammable materials have been

removed. There are many highly flammable items

used in homes such as acetone, denatured alcohol,

gasoline, kerosene, some household cleaners,

some spot removers, turpentines, waxes, wax

removers and products containing petroleum

distillates.

n The laundry process can reduce the flame

retardancy of fabrics. To avoid such a result,

carefully follow the garment manufacturer’s

care instructions.

Do not dry articles containing rubber, plastic, foam

or similar materials such as padded bras, tennis

shoes, galoshes, bath mats, rugs, bibs, baby pants,

plastic bags, pillows, etc., that may melt or burn.

Some rubber materials, when heated, can under

certain circumstances produce fire by spontaneous

combustion.

n Do not store plastic, paper or clothing that may

burn or melt on top of the dryer during operation.

n Garments labeled Dry Away from Heat or Do Not

Tumble Dry (such as life jackets containing kapok)

must not be put in your dryer.

n Do not dry fiberglass articles in your dryer.

Skin irritation could result from the remaining

particles that may be picked up by clothing

during subsequent dryer uses.

n To minimize the possibility of electric shock, unplug

this appliance from the power supply or disconnect

the dryer at the building’s distribution panel by

removing the fuse or switching off the circuit

breaker before attempting any maintenance or

cleaning (except the removal and cleaning of the

lint filter). NOTE: Pressing START, STOP or POWER

does NOT disconnect the appliance from the

power supply.

WHEN NOT USING YOUR DRYER

n Grasp the plug firmly when disconnecting this

appliance to avoid damage to the cord while

pulling. Place the cord away from traffic areas

so it will not be stepped on, tripped over or

subjected to damage.

Do not attempt to repair or replace any part

of this appliance or attempt any servicing unless

specifically recommended in this Owner’s Manual

or in published user-repair instructions that you

understand and have the skills to carry out.

n Before discarding a dryer, or removing it from

service, remove the dryer door to prevent children

from hiding inside.

n Do not tamper with controls.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

GEAppliances.com

WHEN USING YOUR DRYER (cont.)

n Never attempt to operate this appliance if it is

damaged, malfunctioning, partially disassembled,

or has missing or broken parts, including a

damaged cord or plug.

n The interior of the machine and the exhaust

duct connection inside the dryer should be cleaned

at least once a year by a qualified technician.

See the Loading and Using the Dryer section.

n If yours is a gas dryer, it is equipped with an

automatic electric ignition and does not have

a pilot light. DO NOT ATTEMPT TO LIGHT WITH A

MATCH. Burns may result from having your hand

in the vicinity of the burner when the automatic

ignition turns on.

n You may wish to soften your laundered fabrics

or reduce the static electricity in them by using

a dryer-applied fabric softener or an anti-static

conditioner. We recommend you use either

a fabric softener in the wash cycle, according

to the manufacturer’s instructions for those

products, or try a dryer-added product for which

the manufacturer gives written assurance on

the package that their product can be safely

used in your dryer. Service or performance

problems caused by use of these products

are the responsibility of the manufacturers

of those products and are not covered under

the warranty to this appliance.

n Never attempt to use the STEAM DEWRINKLE

or STEAM REFRESH cycles without clothes in the

drum.

About the dryer control panel.

You can locate your model number at the top inside of the door opening.

Model GFDN240/245

SPEED DRY

NORMAL /

MIXED LOAD

ASY

ARE

DELICATES

ACTIVE WEAR

COTTONS

EWRINKLE

IME

LUFF

NO HEAT

Model GFDS350/355

SENSOR DRY

About the dryer control panel.

Power

Press to “wake up” the display. If the display is active, press to put the dryer in the standby mode.

NOTE: Pressing POWER does not disconnect the appliance from the power supply.

Dry Cycles

The dry cycle controls the length and tumble speed of the drying process. The chart below will help you match the dry

setting with the loads.

Sensor Cycles Description

COTTONS

For cottons and most linens.

NORMAL/MIXED LOADS

For loads consisting of cottons and poly-blends.

EASY CARE

For wrinkle-free and permanent press items.

ACTIVE WEAR

Clothing worn for active sports exercise and some casual wear. Fabrics include new

technology finishes and stretch fibers such as Spandex.

DELICATES

For lingerie and special-care fabrics.

SPEED DRY

For small loads that are needed in a hurry, such as sports or school uniforms. Can also be

used if the previous cycle left some items damp, such as collars or waistbands.

Timed Dry Cycles Description

WARM UP

Provides 10 minutes of warming time to warm up clothes.

AIR FLUFF

Use this feature to tumble items without heat.

DEWRINKLE

(on some models)

For removing wrinkles from items that are dry or slightly damp. This cycle is not

recommended for delicate fabrics.

STEAM REFRESH

(on some models)

For slightly wrinkled dry garments. Significantly reduces wrinkles on up to 5 garments. After

the STEAM REFRESH Cycle, the unit will beep and display “0:00.” If the unit is not turned off

or if the door is not opened, the dryer will continue to tumble for 30 minutes. At the end of 30

minutes, it will display “0:00” and the cycle will be complete.

Note: A single extremely light fabric item may need to have an additional item included in the

STEAM REFRESH cycle to achieve optimum results.

STEAM DEWRINKLE

(on some models)

For use with larger loads than STEAM REFRESH. Ideal for loads left in dryer for an extended

time.

My Cycle Description

MY CYCLE

Press to use, create or modify custom dry cycles. (See page 8 for more details)

Timed Dry

Use to set your own dry time. TIMED DRY is also recommended for small loads

To use TIMED DRY:

1. Turn dry cycle dial to TIMED DRY.

2. Increase the drying time by pressing the TIMEDRY ADJUST

button.

Note: This button only increases the time. When max time is reached, pressing the button again will reset the counter to

the lowest setting.

3. Select the TEMP.

4. Close the door.

5. Press Start

GEAppliances.com

ANTI-BACTERIAL

This option may only be used with COTTONS or NORMAL/MIXED LOAD cycles. This option reduces

(on some models) certain types of bacteria by 99.9%, including: Staphylococcus aureus, Pseu-

domonas aeruginosa and Klebsiella pneumoniae*. The anti-bacterial process occurs when high heat

is used during a portion of this drying cycle.

NOTE: Do not use this cycle on delicate fabrics.

* The Anti-Bacterial Cycle is Certified by NSF International (formerly National Sanitation Foundation) to

NSF Protocol P154 Sanitization Performance of Residential Clothes Dryers.

HIGH

For regular to heavy cottons.

MEDIUM

For synthetics, blends and items labeled permanent press.

LOW

For delicates, synthetics and items labeled Tumble Dry Low.

EXTRA LOW

For lingerie and special-care fabrics.

Sensor Dry “Level”

The sensor continuously monitors the amount of moisture in the load. When the moisture in your clothes reaches your

selected dry level, the dryer will stop.

Note: Sensor dry “LEVEL” only works for COTTONS, NORMAL/MIXED LOAD, ACTIVE WEAR, DELICATES, and SPEED DRY.

Dry “Temp”

You can change the temperature of your dry cycle.

START

Press to start a dry cycle. If the dryer is running, press it once and it will pause the dryer.

Press it again to resume the dry cycle.

My Cycle

Set up your favorite combination of settings and save them here for one touch recall.

These custom settings can be set while a cycle is in progress.

To store a MY CYCLE combination of settings:

1. Select your drying cycle.

2. Change DRY “TEMP”, and SENSOR DRY “LEVEL” settings to fit your needs.

3. Select any drying OPTIONS you want.

4. Press and hold the

MY CYCLE

pad for three seconds to store your selection. A beep will sound and the pad will light

up.

To recall your stored MY CYCLE combination:

Press the MY CYCLE button before drying a load.

To change your stored MY CYCLE combination:

Follow steps 1–4 in “To store a MY CYCLE combination of settings”.

“CLEAN LINT FILTER” (message)

(This message represents only a reminder and does not always appear when filter needs cleaning. The filter should be

cleaned after every drying cycle is complete.)

This message will disappear after the START button is pressed. Even though you may have already cleaned the filter

(before or after the POWER button has been pressed), the “CLEAN LINT FILTER” message will still be displayed until the

START button is activated.

About cycle options.

NOTE: Not all features are available on all dryer models. GEAppliances.com

Extended Tumble

Minimizes wrinkles by adding approximately

60 minutes of no-heat tumbling after clothes

are dry. The beeper will sound every two

minutes as a reminder to remove the clothes.

The ESTIMATED TIME REMAINING display will

show 00.

The Extended Tumble time does not get

added to the cycle time on the display

Damp Alert

This option causes the dryer to beep when

clothes have dried to a damp level. Remove

items that you wish to hang dry. The

DAMP ALERT will only beep when this option

is selected.

Removing clothes and hanging them when

they are damp can reduce the need to iron

some items.

Delay Start

Use to delay the start of your dryer.

1. Choose your dry cycle and any options.

2. Press DELAY START. You can increase

the delay time in 1 hour increments using

the DELAY START button.

3. Press the START pad to start

the countdown.

NOTES:

n If the door is opened while the dryer is

in DELAY START, the countdown time

will not restart unless the door is closed

and START has been pressed again.

e-DRY

Reduces the total energy consumption of

specific dryer cycles by adjusting certain

heat settings.

Note: Cycle times will change when e-DRY is

selected.

This feature can be used with DELICATES,

ACTIVE WEAR, EASY CARE, NORMAL/MIXED

LOADS and COTTONS.

Signal

Alerts you that the cycle is complete.

The beeper will continue to sound every

minute for the next 5 minutes, until the

clothes have been removed. The clothes

should be removed when the beeper goes

off so wrinkles don’t set in.

Press SIGNAL to select low, medium or high

volume, or to turn the beeper off.

About cycle options. NOTE: Not all features are available on all dryer models.

My Cycle

To save a favorite cycle, set the desired settings

and hold down the MY CYCLE button for 3

seconds. A beep will sound to indicate the cycle

has been saved.

To use your custom cycle, press

the MY CYCLE button before drying a load.

To change the saved cycle, set the desired

settings and hold down the MY CYCLE button

for 3 seconds.

Estimated Time Remaining

Displays the approximate time remaining until

the end of the cycle.

As the cycle begins, you will see an initial

approximate total cycle time in the display.

Then lights will “race” in the display. This means

the dryer is continuously monitoring

the amount of moisture in the load.

The lights will continue until the dryer senses a

low level of moisture in the load. At that point,

the dryer will calculate and display

the approximate time remaining.

Drying Rack (on some models)

A handy drying rack may be used for drying delicate items such as washable

sweaters. Place items flat on the drying rack and block such items as wool

sweaters and delicate fabrics. Dry with low heat.

To install the drying rack, pull up the lint filter slightly. Insert the drying rack into

the slots, then push the filter back down.

NOTE:

n The drying rack is designed for use with the TIMED DRY cycles. Use with sensor

cycles may result in damp items or extended cycle times.

n Do not use this drying rack when there are other clothes in the dryer, that are

not placed on the rack.

About dryer features.

Drum Lamp

Before replacing the light bulb, be sure to unplug the dryer power cord

or disconnect the dryer at the household distribution panel by removing

the fuse or switching off the circuit breaker. Reach above dryer

opening

from inside the drum. Remove the

bulb and replace with the same size bulb.

Note: Drum lamp only (and automatically) turns on when the dryer door is open.

Lock

You can lock the controls to prevent any

selections from being made. You can also lock

the controls after you have started a cycle.

Children cannot accidentally start the dryer

by touching pads with this option selected.

To lock the dryer, press the lock icon. To unlock

the dryer, press and hold the lock icon for 3

seconds.

The Lock icon next to the timer will light up

when the controls are locked.

Reversing the door swing. GEAppliances.com

IMPORTANT NOTES:

n Read the instructions all the way

through before starting.

n Handle parts carefully to avoid

scratching paint.

n Set screws down by their related parts

to avoid using them in the wrong places.

n Provide a non-scratching work surface

for the door.

n Normal completion time to reverse

the door swing is 30–60 minutes.

IMPORTANT: Once you begin, do not move

the cabinet until door-swing reversal is

completed.

These instructions are for changing

the hinges from the right side to the left

side—if you ever want to switch them

back to the right side, follow these same

instructions and reverse all references

to the left and right.

TOOLS YOU WILL NEED

Adjustable Crescent Wrench

Phillips Head Screwdriver

Putty Knife or

Thin-Blade

Screwdriver

DOOR PARTS

Hinge

Cover

Plastic Cover

STEP-BY-STEP INSTRUCTIONS

3 - # 8 Screws

(door asm and front panel)

8 - # 8 Screws

(inner door, outer ring & hinge cover)

4 - # 8 Screws

(strike plate)

6 - # 8 Machine Screws

(inner door & hinge)

7 - Beauty Buttons

Hinge Assembly

Before You Start

1. Unplug the dryer from its electrical outlet.

Reversing the door swing.

STEP-BY-STEP INSTRUCTIONS (cont.)

Remove Door Assembly

2. Open the door to approximately 130 degrees.

3. Remove the 2 screws starting from the bottom to the top. Make sure the door

is supported while removing the screws.

4. Loosen the top screw as shown. Unhook the door by lifting and pulling.

5. Place the door on a soft protected flat surface so the inner door faces upward (door

resting on handle side). Remove the 8 tapping screws located around the perimeter of

the door outlining the gasket. Remove the 6 machine screws. Using a putty knife or any

other flat tool, remove the 2 beauty buttons and install them on the opposite side.

Remove

Top Screw

8-#8 Tapping Screws

6-# 8 Machine Tapping Screws

4 Beauty Buttons

Outer Door Assembly

Hinge Assembly

Hinge Cover

Remove Hinge and Cover

IMPORTANT: Note the location of the hinge (left or right) before removing.

6. With the screws removed, turn the door over and separate the outer door

assembly and hinge cover of the door from the door frame and set aside.

GEAppliances.com

STEP-BY-STEP INSTRUCTIONS (cont.)

Reinstall Hinge Assembly

7. Install the hinge assembly in the opposite side of the door as shown. Push the

hinge assembly in place until the hinge holes align with the door holes.

8. Hold the hinge and door on their side with one hand and fasten the 6

machine screws as shown.

Reinstall Hinge Cover

9. Insert the hinge cover. Align the hinge cover holes with the holes in the door.

10. Secure the hinge cover with 2 taping screws.

Machine

screws

Hinge

Cover

Tapping

Screws

STEP-BY-STEP INSTRUCTIONS (cont.)

Reassemble Door Assembly

IMPORTANT: Make sure there is no dirt or any other foreign material in between the

window panes.

11. Place the plastic outer door onto the inner door. Make sure that the handle part of

the outer door is opposite the hinge as shown.

12. Turn the door over and fasten the outer door to the inner door using the 6 tapping

screws.

Reversing the door swing.

Move Strike Bracket

13. Using a putty knife or any other flat tool, remove the 3 beauty buttons located on the

dryer where the door will be installed and install them on the opposite side.

14. Switch the strike bracket and its cover to the opposite side by removing the screws.

Reinstall both on the opposite side.

Beauty Buttons

Tapping

Screws

Reinstall Door Assembly

15. The door is now ready to be installed on the dryer. To ease this step,

the hinge has keyholes that allow a partially fastened screw to be used

as a hook.

Partially fasten a screw to the uppermost screw hole. Hook the door on the partially

fastened screw.

Fasten the hinge by installing the other 2 screws and tightening the partially

fastened screw above.

Partially

Inserted

Screw

Tighten All

Screws

Inner Door

Outer Door

Fabric Care Labels

Below are fabric care label “symbols” that affect the clothing you will be laundering.

Always follow the fabric manufacturer’s care label when laundering.

Loading and using the dryer.

Sorting and Loading Hints

As a general rule, if clothes are sorted

properly for the washer, they are sorted properly

for the dryer. Try also to sort items according to size.

For example, do not dry a sheet with socks or other

small items.

Do not add fabric softener sheets once the load

has become warm. They may cause fabric softener

stains. Bounce

Fabric Conditioner Dryer Sheets

have been approved for use in all GE Dryers when

used in accordance with the manufacturer’s

instructions.

Do not overload. This wastes energy and causes

wrinkling.

Do not dry the following items: fiberglass items,

woolens, rubber-coated items, plastics, items with

plastic trim and foam-filled items.

Machine

wash

cycle

Normal

Permanent Press/

wrinkle resistant

Gentle/

delicate

Hand wash

Do not wash Do not wring

Tumble

dry

Dry

Normal

Permanent Press/

wrinkle resistant

Gentle/

delicate

Do not tumble dry

Do not dry

(used with

do not wash)

Heat

setting

High

Medium

Low

No heat/air

Special

instructions

Line dry/

hang to dry

Drip dry

Dry at

In the shade

WASH LABELS

DRY LABELS

Bleach

symbols

Any bleach

(when needed)

Only non-chlorine bleach

(when needed)

Do not bleach

BLEACH LABELS

Front load

target water

temperature

Target Automatic

Category Water Temperature Temperature Control

Tap Cold Inlet Water Temperature Not used

Cold 27°C/80°F Used

Warm 40°C/105°F Used

Hot 50°C/120°F Used

Sanitize 70°C/160°F Used

GEAppliances.com

Care and Cleaning of the Dryer

The Exterior: Wipe or dust any spills or washing

compounds with a damp cloth. Dryer control

panel and finishes may be damaged by some

laundry pretreatment soil and stain remover

products. Apply these products away from

the dryer. The fabric may then be washed and

dried normally. Damage to your dryer caused by

these products is not covered by your warranty.

The Lint Filter: Clean the lint

filter before each use.

Pull out the lint filter.

Moisten your fingers and

remove the captured lint.

Once clean, slide the filter

back into position. Have a

qualified technician vacuum

the lint from the dryer once

a year.

NEVER OPERATE THE DRYER WITHOUT ITS FILTER

IN PLACE.

Stainless Steel: To clean stainless steel surfaces

use a damp cloth with a mild, non-abrasive cleaner

suitable for stainless steel surfaces. Remove the

cleaner residue and then dry with a clean cloth.

The stainless steel used to make the dryer drum

provides the highest reliability available in a GE

dryer. If the dryer drum should be scratched or

dented during normal use, the drum will not rust or

corrode. These surface blemishes will not affect the

function or durability of the drum.

Dryer Interior and Duct: The interior of the

appliance and exhaust duct should be cleaned

once a year by qualified service personnel.

The Exhaust Duct: Inspect and clean the exhaust

ducting at least once a year to prevent clogging.

A partially clogged exhaust can lengthen the

drying time.

Follow these steps:

Turn off electrical supply by disconnecting

the plug from the wall socket.

Disconnect the duct from the dryer.

Vacuum the duct with the hose attachment

and reconnect the duct.

The Exhaust Hood: Check with a mirror that

the inside flaps of the hood move freely when

operating. Make sure that there is no wildlife

(birds, insects, etc.) nesting inside the duct

or hood.

Always follow the fabric manufacturer’s care label when laundering.

Loading and using the dryer.

Venting the dryer. GEAppliances.com

Correct

Venting

Incorrect

Venting

For the best drying performance, the dryer needs to be properly vented. The dryer will use

more energy and run longer if it is not vented to the below specifications. Carefully follow

the details on Exhausting in the Installation Instructions.

n Use only rigid metal 4″ diameter ductwork inside the dryer cabinet and use only UL

approved transition ducting between the dryer and the home duct.

n Do not use plastic or other combustible ductwork.

n Use the shortest length possible.

n Do not crush, kink or collapse the duct.

n Avoid resting the duct on sharp objects.

n Venting must conform to local building codes.

n Do not remove the vent protector from the back of the dryer (on some models).

n Flip the protector down to its lowest position and connect the exhaust duct

to the dryer. The lowered protector will prevent the duct from getting crushed

(on some models).

Vent protector

in place

(on some models)

Connecting Inlet Hoses.

To produce steam, the dryer must connect to the cold water supply. Since the washer

must also connect to the cold water, a “Y” connector is inserted to allow both inlet hoses

to make that connection at the same time.

NOTE: Use the new inlet hoses provided; never use old hoses.

Connect to Cold Water Supply

1. Turn the cold water faucet off. Remove the washer inlet hose from the washer fill

valve connector (cold).

2. Ensure the rubber flat washer is in place and screw the female coupling of the short

hose onto the washer fill valve connector. Tighten by hand until firmly seated.

3. Attach the female end of the ‘’Y’’ connector to the male coupling of the short hose.

Ensure the rubber flat washer is in place. Tighten by hand until firmly seated.

4. Insert the filter screen in the coupling of the washer’s inlet hose. If a rubber flat

washer is already in place remove it before installing the filter screen. Attach this

coupling to one male end of the ‘’Y’’ connector. Tighten by hand until firmly seated.

5. Ensure the rubber flat washer is in place and attach the dryer’s long inlet hose to the

other male end of the ‘’Y’’ connector. Tighten by hand until firmly seated.

6. Ensure the rubber flat washer is in place and attach the other end of the dryer’s long

inlet hose to the fill valve connector at the bottom of the dryer back panel. Tighten by

hand until firmly seated.

7. Using pliers, tighten all the couplings with an additional two–thirds turn.

NOTE: Do not overtighten. Damage to the couplings may result.

8. Turn the water faucet on.

9. Check for leaks around the ‘’Y’’ connector, faucet and hose couplings.

“Y” Connector

Stacking. GEAppliances.com

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT: Save these instructions for local

electrical inspector’s use.

IMPORTANT: Observe all governing codes and

ordinances.

n Note to Installer – Be sure to leave these

instructions with the Consumer.

n Note to Consumer – Keep these instructions

for future reference.

n Installation must be performed by a qualified

installer.

n Proper installation is the responsibility

of the installer.

FOR YOUR SAFETY

WARNING!

Electric Shock Hazard. Disconnect power before

installing. Failure to do so could result in serious

injury or death.

Potential Personal Injury. When stacking the

dryer, more than two people are recommended

to lift the dryer into position because of its

weight and size. Failure to do so could result in

personal injury or death.

When stacking the dryer,

avoid tipping and

rupture of utility services. Dryer must be

securely attached to the washer. DO NOT place

the washer on top of the dryer. Failure to do so

could result in personal injury/death or property

damage.

Mobile Home or Manufactured Home Installation

– Stacking of a gas dryer is not permitted in a

mobile home or manufactured home.

MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET

INSTALLATION

Minimum clearance to combustible surfaces

and for air opening are: 0″ both sides, 1″ front, and

3″ rear. Consideration must be given to provide

adequate clearance for installation and service.

ALCOVE OR CLOSET INSTALLATION

If your dryer is approved for installation

in an alcove or closet, it will be stated on

a label on the dryer back.

The dryer MUST be vented to the outdoors. Refer

to dryer Installation Instructions for details.

Minimum clearance between dryer cabinet and

adjacent walls or other surfaces is:

0″ either side

3″ front

4″ rear

Minimum vertical space from floor to overhead

cabinets, ceiling, etc. is 43″ without pedestal,

55″ with pedestal and 84″ stacked.

Closet doors must be louvered or otherwise

ventilated and must contain a minimum

of 60 square inches of open area equally

distributed. If the closet contains both a washer

and a dryer, doors must contain a minimum

of 120 square inches of open area equally

distributed.

Stacking.

KIT CONTENTS (optional kit GE FL STACK)

Right Hand Bracket

Left Hand Bracket

4 Rubber Pads

4 #12 x 1” Screws

4 #8 x 1/2” Screws

TOOLS YOU WILL NEED

Phillips Screwdriver

Open-Ended Wrench

Pliers

Gloves

Level

INSTALLATION PREPARATION

Remove the packaging.

Flatten the product carton to use as a pad

to lay the dryer down on its side. Continue using

the carton to protect the finished floor in front of

the installation location.

Page is loading ...

GE GFDN245ELMS User manual

Brand: GE

Model: GFDN245ELMS

Category: Tumble dryers

Type: User manual

Download PDF

report

in other languages

español: GE GFDN245ELMS Manual de usuario

GE GFDN245ELMS User manual

GE GFDN245ELMS User manual

in other languages

Related papers

Other documents