Genius STEP T Operating instructions

Brand: Genius

Model: STEP T

Category: Gate Opener

Type: Operating instructions

Page is loading ...

AVVERTENZE PER L’INSTALLATORE

OBBLIGHI GENERALI PER LA SICUREZZA

1) ATTENZIONE! È importante per la sicurezza delle persone seguire attentamente tutta l’istruzione.

Una errata installazione o un errato uso del prodotto può portare a gravi danni alle persone.

2) Leggere attentamente le istruzioni prima di iniziare l’installazione del prodotto.

3) I materiali dell’imballaggio (plastica, polistirolo, ecc.) non devono essere lasciati alla portata

dei bambini in quanto potenziali fonti di pericolo.

4) Conservare le istruzioni per riferimenti futuri.

5) Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo indicato in questa

documentazione. Qualsiasi altro utilizzo non espressamente indicato potrebbe pregiudicare

l’integrità del prodotto e/o rappresentare fonte di pericolo.

6) GENIUS declina qualsiasi responsabilità derivata dall’uso improprio o diverso da quello per cui

l’automatismo è destinato.

7) Non installare l’apparecchio in atmosfera esplosiva: la presenza di gas o fumi infiammabili

costituisce un grave pericolo per la sicurezza.

8) Gli elementi costruttivi meccanici devono essere in accordo con quanto stabilito dalle Norme

EN 12604 e EN 12605.

Per i Paesi extra-CEE, oltre ai riferimenti normativi nazionali, per ottenere un livello di sicurezza

adeguato, devono essere seguite le Norme sopra riportate.

9) GENIUS non è responsabile dell’inosservanza della Buona Tecnica nella costruzione delle

chiusure da motorizzare, nonché delle deformazioni che dovessero intervenire nell’utilizzo.

10) L’installazione deve essere effettuata nell’osservanza delle Norme EN 12453 e EN 12445. Il livello

di sicurezza dell’automazione deve essere C+D.

11) Prima di effettuare qualsiasi intervento sull’impianto, togliere l’alimentazione elettrica e scollegare

le batterie.

12) Prevedere sulla rete di alimentazione dell’automazione un interruttore onnipolare con distanza

d’apertura dei contatti uguale o superiore a 3 mm. È consigliabile l’uso di un magnetotermico

da 6A con interruzione onnipolare.

13) Verificare che a monte dell’impianto vi sia un interruttore differenziale con soglia da 0,03 A.

14) Verificare che l’impianto di terra sia realizzato a regola d’arte e collegarvi le parti metalliche

della chiusura.

15) L’automazione dispone di una sicurezza intrinseca antischiacciamento costituita da un control-

lo di coppia. E' comunque necessario verificarne la sogli di intervento secondo quanto

previsto dalle Norme indicate al punto 10.

16) I dispositivi di sicurezza (norma EN 12978) permettono di proteggere eventuali aree di pericolo

da Rischi meccanici di movimento, come ad Es. schiacciamento, convogliamento,

cesoiamento.

17) Per ogni impianto è consigliato l’utilizzo di almeno una segnalazione luminosa nonché di un

cartello di segnalazione fissato adeguatamente sulla struttura dell’infisso, oltre ai dispositivi citati

al punto “16”.

18) GENIUS declina ogni responsabilità ai fini della sicurezza e del buon funzionamento dell’auto-

mazione, in caso vengano utilizzati componenti dell’impianto non di produzione GENIUS.

19) Per la manutenzione utilizzare esclusivamente parti originali GENIUS.

20) Non eseguire alcuna modifica sui componenti facenti parte del sistema d’automazione.

21) L’installatore deve fornire tutte le informazioni relative al funzionamento manuale del sistema in

caso di emergenza e consegnare all’Utente utilizzatore dell’impianto il libretto d’avvertenze

allegato al prodotto.

22) Non permettere ai bambini o persone di sostare nelle vicinanze del prodotto durante il

funzionamento.

23) Tenere fuori dalla portata dei bambini radiocomandi o qualsiasi altro datore di impulso, per

evitare che l’automazione possa essere azionata involontariamente.

24) Il transito tra le ante deve avvenire solo a cancello completamente aperto.

25) L’Utente utilizzatore deve astenersi da qualsiasi tentativo di riparazione o d’intervento diretto e

rivolgersi solo a personale qualificato.

26) Non mettere in corto circuito i poli delle batterie e non tentare di ricaricarle con alimentatori

diversi dalle schede Master o Slave.

27) Non gettare le batterie esauste nei rifiuti ma smaltirle utilizzando gli appositi contenitori per

consentirne il riciclaggio. I costi di smaltimento sono già stati pagati dalla casa costruttrice.

28) Tutto quello che non è previsto espressamente in queste istruzioni non è permesso

IMPORTANT NOTICE FOR THE INSTALLER

GENERAL SAFETY REGULATIONS

1) ATTENTION! To ensure the safety of people, it is important that you read all the following

instructions. Incorrect installation or incorrect use of the product could cause serious harm to

people.

2) Carefully read the instructions before beginning to install the product.

3) Do not leave packing materials (plastic, polystyrene, etc.) within reach of children as such

materials are potential sources of danger.

4) Store these instructions for future reference.

5) This product was designed and built strictly for the use indicated in this documentation. Any other

use, not expressly indicated here, could compromise the good condition/operation of the

product and/or be a source of danger.

6) GENIUS declines all liability caused by improper use or use other than that for which the

automated system was intended.

7) Do not install the equipment in an explosive atmosphere: the presence of inflammable gas or

fumes is a serious danger to safety.

8) The mechanical parts must conform to the provisions of Standards EN 12604 and EN 12605.

For non-EU countries, to obtain an adequate level of safety, the Standards mentioned above

must be observed, in addition to national legal regulations.

9) GENIUS is not responsible for failure to observe Good Technique in the construction of the

closing elements to be motorised, or for any deformation that may occur during use.

10) The installation must conform to Standards EN 12453 and EN 12445. The safety level of the

automated system must be C+D.

11) Before attempting any job on the system, cut out electrical power and disconnect the

batteries.

12) The mains power supply of the automated system must be fitted with an all-pole switch with

contact opening distance of 3mm or greater. Use of a 6A thermal breaker with all-pole circuit

break is recommended.

13) Make sure that a differential switch with threshold of 0.03 A is fitted upstream of the system.

14) Make sure that the earthing system is perfectly constructed, and connect metal parts of the

means of the closure to it.

15) The automated system is supplied with an intrinsic anti-crushing safety device consisting of a

torque control. Nevertheless, its tripping threshold must be checked as specified in the

Standards indicated at point 10.

CONSIGNES POUR L'INSTALLATEUR

RÈGLES DE SÉCURITÉ

1) ATTENTION! Il est important, pour la sécurité des personnes, de suivre à la lettre toutes les

instructions. Une installation erronée ou un usage erroné du produit peut entraîner de graves

conséquences pour les personnes.

2) Lire attentivement les instructions avant d'installer le produit.

3) Les matériaux d'emballage (matière plastique, polystyrène, etc.) ne doivent pas être laissés

à la portée des enfants car ils constituent des sources potentielles de danger.

4) Conserver les instructions pour les références futures.

5) Ce produit a été conçu et construit exclusivement pour l'usage indiqué dans cette

documentation. Toute autre utilisation non expressément indiquée pourrait compromettre

l'intégrité du produit et/ou représenter une source de danger.

6) GENIUS décline toute responsabilité qui dériverait d'usage impropre ou différent de celui

auquel l'automatisme est destiné.

7) Ne pas installer l'appareil dans une atmosphère explosive: la présence de gaz ou de fumées

inflammables constitue un grave danger pour la sécurité.

8) Les composants mécaniques doivent répondre aux prescriptions des Normes EN 12604 et EN

12605.

Pour les Pays extra-CEE, l'obtention d'un niveau de sécurité approprié exige non seulement le

respect des normes nationales, mais également le respect des Normes susmentionnées.

9) GENIUS n'est pas responsable du non-respect de la Bonne Technique dans la construction des

fermetures à motoriser, ni des déformations qui pourraient intervenir lors de l'utilisation.

10) L'installation doit être effectuée conformément aux Normes EN 12453 et EN 12445. Le niveau de

sécurité de l'automatisme doit être C+D.

11) Couper l'alimentation électrique et déconnecter la batterie avant toute intervention sur

l'installation.

12) Prévoir, sur le secteur d'alimentation de l'automatisme, un interrupteur omnipolaire avec une

distance d'ouverture des contacts égale ou supérieure à 3 mm. On recommande d'utiliser un

magnétothermique de 6A avec interruption omnipolaire.

13) Vérifier qu'il y ait, en amont de l'installation, un interrupteur différentiel avec un seuil de 0,03 A.

14) Vérifier que la mise à terre est réalisée selon les règles de l'art et y connecter les pièces

métalliques de la fermeture.

15) L'automatisme dispose d'une sécurité intrinsèque anti-écrasement, formée d'un contrôle du

couple. Il est toutefois nécessaire d'en vérifier le seuil d'intervention suivant les prescriptions des

Normes indiquées au point 10.

16) Les dispositifs de sécurité (norme EN 12978) permettent de protéger des zones éventuellement

dangereuses contre les Risques mécaniques du mouvement, comme l'écrasement,

l'acheminement, le cisaillement.

17) On recommande que toute installation soit doté au moins d'une signalisation lumineuse, d'un

panneau de signalisation fixé, de manière appropriée, sur la structure de la fermeture, ainsi que

des dispositifs cités au point “16”.

18) GENIUS décline toute responsabilité quant à la sécurité et au bon fonctionnement de

l'automatisme si les composants utilisés dans l'installation n'appartiennent pas à la production

GENIUS.

19) Utiliser exclusivement, pour l'entretien, des pièces GENIUS originales.

20) Ne jamais modifier les composants faisant partie du système d'automatisme.

21) L'installateur doit fournir toutes les informations relatives au fonctionnement manuel du système

en cas d'urgence et remettre à l'Usager qui utilise l'installation les "Instructions pour l'Usager"

fournies avec le produit.

22) Interdire aux enfants ou aux tiers de stationner près du produit durant le fonctionnement.

23) Eloigner de la portée des enfants les radiocommandes ou tout autre générateur d'impulsions,

pour éviter tout actionnement involontaire de l'automatisme.

24) Le transit entre les vantaux ne doit avoir lieu que lorsque le portail est complètement ouvert.

25) L'Usager qui utilise l'installation doit éviter toute tentative de réparation ou d'intervention directe

et s'adresser uniquement à un personnel qualifié.

26) Ne pas mettre en court-circuit les pôles des batteries et ne pas tenter de les recharger avec

d'autres platines d'alimentation que les platines Maître ou Esclave.

27) Ne pas jeter les batteries épuisées à la poubelle, mais les éliminer dans les conteneurs

spécifiques pour le recyclage. Les coûts d'élimination des déchets ont déjà été payés par le

constructeur.

28) Tout ce qui n'est pas prévu expressément dans ces instructions est interdit.

16) The safety devices (EN 12978 standard) protect any danger areas against mechanical

movement Risks, such as crushing, dragging, and shearing.

17) Use of at least one indicator-light is recommended for every system, as well as a warning sign

adequately secured to the frame structure, in addition to the devices mentioned at point “16”.

18) GENIUS declines all liability as concerns safety and efficient operation of the automated

system, if system components not produced by GENIUS are used.

19) For maintenance, strictly use original parts by GENIUS.

20) Do not in any way modify the components of the automated system.

21) The installer shall supply all information concerning manual operation of the system in case of

an emergency, and shall hand over to the user the warnings handbook supplied with the

product.

22) Do not allow children or adults to stay near the product while it is operating.

23) Keep remote controls or other pulse generators away from children, to prevent the automated

system from being activated involuntarily.

24) Transit through the leaves is allowed only when the gate is fully open.

25) The user must not attempt any kind of repair or direct action whatever and contact qualified

personnel only.

26) Do not short-circuit the poles of the batteries and do not try to recharge the batteries with power

supply units other than Master or Slave cards.

27) Do not throw exhausted batteries into containers for other waste but dispose of them in the

appropriate containers to enable them to be recycled. Disposal costs have already been

paid for by the manufacturer.

28) Anything not expressly specified in these instructions is not permitted.

ENGLISH

LEDOMT-PETS

ylppusrewoP cdV21

)W(rewopdebrosbadetaR 84

).nim/m(deepseerf-daolraenilxaM 51

)N(ecrofcitatS 051

lcycevitucesnoC 03

emityrevoceR

detelpmochcaerof'2

elcyc

)C°(erutarepmettneibmagnitarepO 55+÷02-

)gK(thgiewr

otarepO 3,5

ssalcnoitcetorP 44PI

)m(htgnelxamfaeL 5

)gk(thgiewxamfaeL 003

DxHxLsnoisnemidllarevorotarepO

)mm(

.giFees

Fig.01

Fig.02• Dimensions in mm

STEP-T automated system

These instructions apply to the following model:

GENIUS STEP-T

The STEP-T automated system automates residential sliding gates

with leaves of up to 5 m in length and 300 kg in weight.

It consists of a non-reversing electro-mechanical gearmotor,

supply board. The STEP-T houses a programmable electronic control

board that enables setting of function logics, work times (by self-

learning) and pause times, gate speed, anti-crushing sensitivity

as well as partial-opening width.

The non-reversing system guarantees the gate will automatically

lock when the motor is not operating. A release system enables

the gate to be moved by hand in case of malfunction.

The STEP-T automated system was designed and built for controlling

vehicle access. Do not use for any other purpose.

1. DESCRIPTION AND TECHNICAL SPECIFICATIONS

Tab. 1 - Technical specifications of STEP-T operator

30 consecutive cycles can be performed with software thermal

protection. Recovery time is 2' each cycle performed.

2. DIMENSIONS

1) STEP-T operator

2) Protective side panels

3) Pinion

4) Manual release

5) Foundation plate

6) Control board

7) Toroidal transformer

8) Support for transformer and power supply board

9) Power supply board

10) Hand guards

11) Antenna (Optional)

ENGLISH

2x1,5 mm + (230Vac)

Fig.03

Fig.04

Fig.05

175,5

Fig.06

Fig.07

90,5

1) Operator with equipment.

2) Photocells

3) Key operated push-button

4) Flashing lamp

5) Radio receiver

*Use the dimensions according to type of rack

Galvanised rack 30x6 = 36.5mm

Galvanised rack 30x12 = 39.5mm

Nylon rack 30x20 = 41.5mm

*Use the dimensions according to type of rack

Galvanised rack 30x6 = 36.5mm

Galvanised rack 30x12 = 39.5mm

Nylon rack 30x20 = 41.5mm

Closing dir.

3. DESCRIPTION OF SYSTEM - ELECTRICAL EQUIPMENT

(standard system)

Notes:

1) To lay electric cables, use adequate rigid and/or flexible tubes.

2) To avoid any kind of interference always separate low voltage

connection cables from 230Vac power cables.

4. INSTALLING THE AUTOMATED SYSTEM

4.1. Preliminary checks

To ensure safety and an efficiently operating automated system,

make sure the following conditions are observed:

• The structure of the gate must be suitable for being automated.

In particular, check that the structure is sufficiently strong and

rigid, and that its dimensions and weight conform to those

indicated in the technical specifications.

• Make sure that the gate slides without any inclination.

• Make sure that the gate moves uniformly and correctly, without

any irregular friction during its entire travel.

• The soil must permit sufficient stability for the expansion plugs

securing the foundation plate.

• Check if the upper guide and travel limit mechanical stops are

installed.

• Remove any locks and lock bolts.

We advise you to have any metalwork carried out before the

automated system is installed.

4.2. Preparing the fundation plate

• Fit the 4 supplied caged nuts, as shown in Fig. 4, in the 4 square

holes of the plate.

4.3. Securing the foundation plate

1) The foundation plate must be located as shown in Fig. 5 (right

closing) or Fig. 6 (left closing) to ensure the rack and pinion mesh

correctly.

2) Secure the foundation plate to the floor, using adequate

expansion plugs (Fig. 7) and provide one or more sheaths for

routing the electric cables through the plate (Figs . 5-6 Ref. 1).

Using a spirit level, check if the plate is perfectly horizontal.

ENGLISH

Fig.09

Fig.08

Fig.10

Fig.11

Fig.12

Use the dimensions according to type of rack:

Galvanised rack 30x6

! A = 46.5mm and B =146mm

Galvanised rack 30x12

! A = 49.5mm and B =146mm

Nylon rack 30x20

! A = 51.5mm and B =112.5mm

4.4. Positioning the operator

• Lay the electric cables for connection to the accessories and

power supply as shown in Fig. 3. To facilitate making the

connections, allow the cables to project by the required length

for connection to the terminal board, transformer and decoding

card (if provided).

• Position the operator on the plate, using the supplied screws as

shown in Fig. 8.

4.5. Adjusting the operator

• Adjust the distance of the operator from the gate by referring to

Fig. 9.

4.6. Securing the operator

• Temporarily fix the operator by slightly tightening the screws as

shown in Fig. 10.

4.7. Releasing the operator

Prepare the operator for manual operating mode as described

below:

• Open the protective door with a coin.

• Take the supplied key located inside the door, fit it in the release

system and turn it clockwise until it reaches the mechanical

stop (Fig. 11).

4.8 Installing the rack

4.8.1. Steel rack to be welded (Fig. 12)

1) Place the three threaded pawls on the rack element,

positioning them at the top of the slot. In this way, the slot play

will enable any adjustments to be made.

2) Manually take the leaf into its closing position.

3) Lay the first piece of rack at appropriate level on the pinion

and weld the threaded pawl on the gate as shown in Fig. 15.

4) Move the gate manually, checking if the rack is resting on the

pinion, and weld the second and third pawl.

5) Bring another rack element near to the previous one, using a

piece of rack (as shown in Fig. 16 BRef.1) to synchronise the

teeth of the two elements.

6) Move the gate manually and weld the three threaded pawls,

so proceeding until the gate is fully covered.

4.8.2. Steel rack to be screwed (Fig. 13)

1) Manually take the leaf into its closing position.

2) Lay the first piece of rack at the appropriate level on the pinion

and place the spacer between rack and gate, positioning it

at the top of the slot.

3) Mark the hole position on the gate. Drill a Ø 6.5 mm hole and

thread with a M8 mm tap. Screw the bolt.

4) Move the gate manually, checking if the rack is resting on the

pinion, and repeat the operations at point 3.

5) Bring another rack element near to the previous one, using a

piece of rack (as shown in Fig. 16 Ref.1) to synchronise the teeth

of the two elements.

6) Move the gate manually and carry out the securing operations

as for the first element, proceeding until the gate is fully covered.

ENGLISH

Fig.13

Fig.14

Fig.16

Fig.15

Fig.17

4.8.3. Nylon rack to be screwed (Fig. 14)

1) Manually take the leaf into its closing position.

2) Lay on the pinion the first piece of rack at the appropriate level

and mark the hole position on the gate; make a hole with a 4

mm bit and screw the 6x20 mm self-tapping screw with reinforcing

plate.

3) Move the gate manually, checking if the rack is resting on the

pinion, and repeat the operations at point 2.

4) Bring another rack element near to the previous one, using a

piece of rack (as shown in Fig. 16 Ref.1) to synchronise the teeth

of the two elements.

5) Move the gate manually and carry out the securing operations

as for the first element, proceeding until the gate is fully covered.

Notes on rack installation

• Make sure that, during the gate travel, all the rack elements

mesh correctly with the pinion.

• Do not, on any account, weld the rack elements either to the

spacers or to each other.

• When you have finished installing the rack, adjust the distance

between the pinion teeth and the rack groove, checking if the

distance is 1.5 mm (Fig. 17) along the entire travel, using the rack

slots.

• Manually check if the gate habitually reaches the travel limit

mechanical stops and make sure that there is no friction during

gate travel.

• Do not use grease or other lubricants between rack and pinion.

ENGLISH

Fig.18

J10

LED

Jumpers position

must not be modified

CONTROL BOARD

DEL SDELgnimmargorP

P DELscitsongaiddnaNOrewoP

1P nottub-hsupgnimmargorp"noitcnuF"

2P nottub-hsupgnimmargorp

"eulaV"

1F A02FesufrotomdnayrettaB

1J draoblanimreTseirosseccA

2J desutoN

3J draoblanimretnoitcennocrotoM

4J ti

nuylppusrewoprofrotcennoC

5J rotcennocrevieceR

01J draoblanimretrosnescitengaM

WARNINGS

Attention: Before attempting any job on the control board (connections, maintenance), cut out electric power.

• Install, upstream of the system, a differential thermal breaker with adequate tripping threshold.

• Always separate 230VAC power cable from control and safety cables (push-buttons, receiver, photocells, etc.). To avoid any

electric noise, use separate sheaths or a shielded cable (with earthed shield).

ylppusrewoP zH06/05)%01-%6+(~V032

rewopdebrosbA W081

tnerrucxamrotoM A51

erutarepmettneibmagnitarepO C°55+÷C

°02-

sesufnoitcetorP A02-1°N

noitcnufgnihsurc-itnA lortnoctnerruC/redocnE

cdV42tadaol.xamseirosseccA Am051

aolxamrotcennocdipaR Am05

scigolnoitcnuFL citamotua-imeS/ecivedytefaS/citamotua"deppetS"/citamotuA

emitgn

isolc/gninepO gninrael-flesyB

emitesuaP .ces03,02,01,5:elbammargorP

htdiwgninepolaitraP .mc081,051,021,09

eepS slevel4noelbatceleS

tnemtsujdaecrofcitatS slevel4noelbatceleS

noitareleceD cinortcelE

stupnidraoblanim

reT rosneS-.gnslctasecivedytefaS-.gnpotasecivedytefaS-potS-nepOyllaitraP-nepO

stuptuodraoblanimreT ylppu

srewopcdV21-cdV42seirosseccA-thgil-rotacidni-pmalgnihsalF-rotoM

srotcennoC tinuylppusrewop-dracreviecer

snoitcnufelbammargorP deepsrotarepo-ecrofgnihsurc-itna-htdiwgninepolaitrap-emitesuap-cigoL

5. BOARD LAYOUT

NB: the Power Supply Unit consists of the toroidal transformer and

the power supply board.

6. CONTROL BOARD TECHNICAL SPECIFICATIONS

Tab. 2 - Technical specifications

ENGLISH

Fig.19

7. ELECTRICAL CONNECTIONS

Wire up as shown in Fig. 19

7.1 Description of J1 terminal board

Tab. 3 - Description of accessories connection

(1)

If no devices are connected, connect the terminal to earth (terminals 12 ÷ 15).

lanimreTnoitpircseD yrosseccadetcennoC

1ANEPO)dnammocgninepolatot( )nottub-hsupdetarepoyek.g.e(tcatnocANhti

weciveD

2BNEPO)dnammocgninepolaitrap( )nottub-hsupdetarepoyek.g.e(tcatnocANhtiweciveD

3POTS)dnammockcoletag(

.tcatnocCNhtiweciveD

)1(

4POWSF)tcatnocsecivedytefasgninepo( sllecotohP

)1(

5LCWSF)tcatnocsecivedytefasgnisolc( sllecotohP

)1(

6DESUTON/

8-7+ )ylppusrewopV42rofevitisop( Am051fonoitprosbalatotXAMseirosseccA

11-9.L.W)thgilrotacidniotylppus

rewop( pmalW5.0-V21

11-01PMAL)pmalgnihsalfotylppusrewop( pmalgnihsalfV21

51÷21- )ylppusrewopcdV42rofevitagen( /

For connection of photocells, see par. 7.3

Not used

ENGLISH

Fig.20

Fig.21

Fig.22

Fig.23

Connection of 2 NC contacts in series

Connection of 2 NA contacts in parallel

Opening or

opening/closing safety devices

Closing safety devices

Opening safety devices

Closing Dir.

BROWN

BLUE

Closing Dir.

BROWN

BLUE

7.2 Wiring the motor

Wire the STEP-T motor according to the gate closing direction as shown in the figure below.

7.3 Connection of photocells and safety devices

Before connecting the photocells (or other devices) we advise you to select the type of operation according to the movement area

to be protected (see Fig. 21).

N.B.: If two devices with NC contact have the same function, they

must be connected to each other in series (Fig. 22).

N.B.: If two devices with NA contact have the same function, they

must be connected to each other in parallel (Fig. 23).

Power supply unit

ENGLISH

Fig.24

J10

AB CDE

1234

Fig.25

1 pair of OPENING photocells

1 pair of CLOSING photocells

1 pair of CLOSING photocells and 1

pair of OPENING/CLOSING photocells

2 pairs of CLOSING photocells

connection of no devices

Attention: a maximum of 2 pairs of photocells can be connected to the control board

Examples of photocell connections

7.4 Connection of receiver card

Insert the receiver card in the block connector J5 (Fig. 18) as indicated in Fig. 25.

For programming the receiver card, consult the individual instructions.

ENGLISH

AB CDE

1234

max 5mm

ossifoseccA

eeteridenoisnetalledazneserpalacidnI

osu'llaatnorpadehcs

etnaiggepmaL

enoisnecca(ecolev

).cesm

052ingo

enoizetorpalledenoizavitta'lacidnI

2onemlaerednettaerroccO.acimret

olcicnueriugeseretoprepitunim

otnepS

.eteridenoisnetalledaznacnamalacidnI

nonenoizamotua'lesafatseuqetnaruD

anoiznuf

Fig.26

Fig.27

Fig.28

Fig.29

Fig.30

8. START-UP

8.1 Powering up the system

After making all the cable connections we described previously,

power up the system to enable diagnostics, positioning of the

travel limit magnets, check of inputs status and programming.

8.2 Diagnostics

LED "P" (see Fig.18) - visible from inside the enclosure - performs the

diagnostics function. The LED has 3 statuses as shown in the table

below:

Tab. 4 - LED P status description

8.3 Positioning the travel limit magnets

8.3.1 Prearrangement

The STEP-T operator is supplied with a sensor which, by detecting

the transit of two magnets secured to the top of the rack,

commands the gate to stop when closing or opening.

Procedure for correct positioning of the two supplied magnets:

• Assemble the magnets according to the type of rack used:

1) Galvanised rack 30x6 module 4 (Fig. 26 - Ref. 1)

2) Galvanised rack 30x12 module 4 (Fig. 26 - Ref. 2)

3) Reinforced nylon rack 30x20 module 4 (Fig. 26 - Ref. 3)

8.3.2 Positioning

• Position the magnets on the rack as shown in Fig. 27 Ref 1. Make

sure that distance between the magnet and the operator's

body is 5mm max (Fig. 27 Ref. 2).

• Fully tighten the operator fixing screws(Fig. 10).

8.3.3 Adjustment and Fixing

• Press push-button P2 (Fig. 28 and par. 8.4) to enter the inputs

status function.

• Manually take the gate to opening position, but allow a space

of 2 cm from the travel limit mechanical stop.

• Slide the magnet on the rack (Fig. 29) until you see that LED1 on

the control board goes off (Fig. 28).

• Tighten the magnet's securing screws.

• Manually take the gate to closing position, but allow a space

of 2 cm from the travel limit mechanical stop.

• Slide the magnet on the rack (Fig. 30) until you see that LED1 on

the control board goes off (Fig. 28).

• Tighten the magnet's securing screws.

LED 1

ENGLISH

AB CDE

1234

Fig.31

8.3.4 Operator locked

• Make sure the gate is in its closed position.

• Turn the release key anti-clockwise (Fig. 31).

• Remove the release key and put it back in its place; close the

protective door.

• Move the gate until the release meshes.

8.4 Status of inputs

The board has a function for checking the status of inputs on the

terminal board.

In all LEDS OFF status (LEDs both with letters and numbers), press

the P2 push-button.

When the LEDs light up, this indicates the inputs status as shown in

Tab. 5.

Tab. 5 - Description of inputs status LEDS

Notes:

• The status of LEDs with the gate closed at rest is shown in bold.

• In the inputs status function, push-button P1 commands an

OPEN A.

When checks have finished, once again press push-button P2 to

exit the inputs status function.

8.5 Programming

These are the basic settings of the board:

Function logic: A4

Pause times: B1

Partial opening width: C2

Static force: D3

Speed: E3

If you wish to execute customised programming (see par. from

8.5.1 to 8.5.5) and time-learning (see par.8.5.6) follow the steps in

the next pages.

deL

dethgiL

)tcatnocdesolc(

ffO

)tcatnocnepo(

AnepO=AevitcadnammoC evitcanidnammoC

BnepO=BevitcadnammoC evitcan

idnammoC

potS=C evitcanidnammoC evitcadnammoC

powsF=D degagnesidsecivedytefaS degagnesecivedytefaS

lcwsF=E de

gagnesidsecivedytefaS degagnesecivedytefaS

erosneS=1 degagnesidrosneS degagnerosneS

8.5.1 Function Logic

In all LEDs OFF status, press push-button P1.

Led A will light up together with LED 4.

Press push-button P2, for a choice of 4 different function logics.

A1 automatic

A2 safety

A3 Step-by-step automatic

A4 Step-by-step semi-automatic (default)

8.5.2 Pause Times

Press push-button P1 again and LED B will light together with LED

Press push-button P2, for a choice of 4 different pausetimes.

B1 5 seconds (default)

B2 10 seconds

B3 20 seconds

B4 30 seconds

8.5.3 Partial Opening Width

Press push-button P1 again and LED C will light together with LED

ENGLISH

Press push-button P2, for a choice of 4 different partial openings.

C1 90 cm

C2 120 cm (default)

C3 150 cm

C4 180 cm

8.5.4 Static Force

Press push-button P1 again and LED D will light together with LED

Press push-button P2, for a choice of 4 different static forces.

D1 low

D2 medium low

D3 medium high (default)

D4 high

8.5.5 Speed

Press push-button P1 again and LED E will light together with LED

Press push-button P2, for a choice of 4 different speeds

E1 low

E2 medium low

E3 medium high (default)

E4 high

8.5.6 Simple learning

If you press push-button P1 again, all 5 LEDs from A to E will light.

(Make sure that the gate is closed and operator locked)

If you press push-button P2 for 1 second, the gate will start moving

until the opening travel limit magnet engages the sensor on the

operator. The 5 LEDs flash during this stage.

After learning has been completed, the 5 LEDs remain lighted

steadily.

Press push-button P1 again to exit (all LEDs OFF). Give an OPEN A

pulse with the radio control or the key push-button to close the

gate.

8.6 Status of indicator light

If you wish to use a 12V-0.5W indicator light (terminal 9 - 11 of J1,

see Fig. 18), the following table shows the statuses of the indicator

light according to gate position.

Tab. 6 - Statuses of indicator light

8.7 Testing the automated system

After programming, run an accurate functional check of the

automated system and of all the accessories connected to it,

especially the safety devices.

sutatsthgil-rotacidnIsutatsetaG

ffOthgiLdesolC

dethgiLesuapninepO-nepO

gnihsalFgnisolC

dethgiLgninepO

dethgiLdek

coL

ENGLISH

Fig.32

tluaF sesuacelbissoP noituloS

PDELdraoB.nwodtuhsmetsysdetamotuA

FFO

.deilppusrewopsniamoN

rewopsniamlitnudekcolyatslliwetagehT

.snruter

tonseodtI.nwodtuhsmetsysdetamotuA

rolortnocoidar(dnammocynaybevom

.)hctiwsrotcelesdetarepoyek

nslanimret)5dna4(WSFdna)3(POTS

.detcennoc

snoitcurtsniehtninwohssagniriwehtkcehC

thgilEdnaD,CsDELfikcehc

osladna

.sutatsstupniehtnoyltcerroc

.deliafesufdraoB

,yrassecenfi,dna)A02F(esufehtkcehC

.tiecalper

ylnosev

oM.nwodtuhsmetsysdetamotuA

.dnammocdetarepo-yekyb

lortnocoidarytluaF

ehtfikcehc,lortnocoidarrehtonagnisU

fi,dnayltcerrocgnitareposimetsys

.lortnocoidarytluafehtecalper,yrassecen

draobreviecerytluaF

nwodtuhslli

tssimetsysdetamotuaehtfI

sawlortnocoidartahtgnikcehcretfaneve

.dracreviecerehtecalper,ytluafton

rotomehT

.nwodtuhsmetsysdetamotuA

.evomtonseodetagehttub,snur

timillevartehtdehcaersahrotomehT

.potslacinahcem

repsastengamtimillevartehtegnarrA

.snoitcurtsni

metsysdetamotuaeht,tnemevomgniruD

.nosaeronrofnoitomsesreve

yranigaminagniteem(wolootecroF

)elcatsbo

ehtnoselcatsboynaeraerehtfikcehC

nevenurosenotssahcus,etagehtf

oetuor

ehtfoecrofcitatsehtesaercnidna,tlahpsa

.rotom

eritneehtsmrofrepmetsysdetamotuaehT

tiro.noitarelece

dnilevartgnisolc/gninepo

tuohtiwecivedtimillevartehtnospots

.noitarelecedgnimrofrep

.yltcerrocdetucexeto

ngninraeL .snoitcurtsnirepsagninraeletucexE

tonsitengamtimillevartehtfonoitisopehT

.tcerroc

repsasecivedt

imillevartfonoitisopkcehC

niagagninraeletucexednasnoitcurtsni

tapotslacinahcemehtsehcaeretagehT

.deepsll

tonsitengamtimillevartehtfonoitisopehT

.tcerroc

repsasecivedtimillevartfonoitisopkcehC

niagagninraeletucexednasnoitcurtsni

UNLOCK

LOCK

TROUBLESHOOTING

9. MANUAL OPERATION

If the gate has to be moved manually due to a malfunction of

the automated system, use the release device as follows:

• Open the protective door with a coin.

• Take the supplied key located inside the door, fit it in the release

system and turn it clockwise until it reaches the mechanical

stop (fig. 32).

• Open or close the gate manually.

10. RESTORING NORMAL OPERATION MODE

If you wish to relock the gate use the release/lock device as follows:

• Manually take the gate back to its closed position.

• Turn the release key anti-clockwise until it reaches the

mechanical stop (Fig. 32).

• Remove the release key and put it back in its place; close the

protective door.

• Move the gate until the release meshes.

11. MAINTENANCE

Carry out the following jobs at least every 6 months:

• Check if the anti-crushing facility is correctly set.

• Check the efficiency of the release system.

• Check the efficiency of the safety devices and accessories.

12. REPAIRS

For any repairs, contact authorised Repair Centres.

ENGLISH

a/7.baT

"1A"ACIGOL SESLUP

SUTATSETAGA-NEPOBNEPOPOTSSECIVEDYTEFASGNINEPOSECIVEDYTEFASGNISOLCECIVEDYTEFASLC/PO

SOLC emitesuapretfasesolc-erdnasev/faelsnepO )delbasidNEPO(tceffeoNtceffeoN)delbasidNEPO(tceffeoN

ESUAPnoN

EPO emitesuapsdaoleR

noitarepospotS

tceffeoNemitesuapsdaoleR

GNISOLC yletaidemmisev/faelehtsnepo-eR tceffeoN

otsesreveryletaidemmI

nepo

,esaelerno,dnaskcoL

gninepotasesrever

GNINEPO tceffeoN

otsesreveryletaidemmI

esol

tceffeoN

,esaelerno,dnaskcoL

gnineposeunitnoc

DEKCOL sev/faelehtsesolCtceffeoNtceffeoN)delbasidNEPO(tceffeo

b/7.baT

"2A"ACIGOL SESLUP

SUTATSETAGA-NEPOBNEPOPOTSSECIVEDYTEFASGNINEPOSECIVEDYTEFASGNISOLCECIVEDYTEFASLC/PO

SOLC emitesuapretfasesolc-erdnasev/faelsnepO )delbasidNEPO(tceffeoNtceffeoN)delbasidNEPO(tceffeoN

ESUAPnoN

EPO yletaidemmisev/faelehtsesolc-eR

noitarepospotS

tceffeoN ongepmisidla)otibiniNEPO("5opodeduihC

GNISOLC y

letaidemmisev/faelehtsnepo-eR tceffeoN

otsesreveryletaidemmI

nepo

,esaelerno,dnaskcoL

gninepotasesrever

GNI

NEPO yletaidemmisev/faelehtsesolc-eR

otsesreveryletaidemmI

esolc

tceffeoN

,esaelerno,dnaskcoL

gnineposeunitnoc

DEKCOL sev/faelehtsesolCtceffeoNtceffeoN)delbasidNEPO(tceffeoN

c/7.baT

"3A"ACIGOL SESLUP

SUTATSETAGA-NEPOBNEPOPOTSSECIVEDYTEFASGNINEPOSECIVEDYTEFASGNISOLCECIVEDYTEFASLC/PO

SOLC emitesuapretfasesolc-erdnasev/faelsnepO )delbasidNEPO(tceffeoNtceffeoN)delbasidNEPO(tceffeoN

ESUAPnoN

EPO noitarepospotS

noitarepospotS

tceffeoNemitesuapsdaoleR

GNISOLC yletaidemmisev/faelehtsnepo-eR tceffeoN

sesreveryletaidemmI

nepo

,esaelerno,dnaskcoL

gninepotasesrever

GNINEPO noitarepospotS

otsesreveryletaidemmI

esolc

tceffeoN

,esaelerno,dnaskcoL

gnineposeunitnoc

DEKCOL sev/faelehtsesolCtceffeoNtceffeoN)delbasidNEPO(tce

ffeoN

d/7.baT

"4A"ACIGOL SESLUP

SUTATSETAGA-NEPOBNEPOPOTSSECIVEDYTEFASGNINEPOSECIVEDYTEFASGNISOLCECIVEDYTEFASLC/PO

SOLC sev/faelsnepO )delbasidNEPO(tceffeoNtceffeoN)delbasidNEPO(tceffeoN

NEPO yletaidemmisev/faelehtsesolc-e

noitarepospotS

tceffeoN

)delbasidNEPO(tceffeoN

GNISOLC noitarepospotS

otsesreveryletaidemmI

nepo

,esaelerno

,dnaskcoL

gninepotasesrever

GNINEPO noitarepospotS

otsesreveryletaidemmI

esolc

tceffeoN

,esaelerno,dnaskcoL

nineposeunitnoc

DEKCOL

noitceridesrevernignivomstratseR:NEPOretfA

yletaidemmisev/faelehtsesolc-eR:POTSre

tfA

)delbasidNEPO(tceffeoN

ti,nepotsumtifi(tceffeoN

)NEPOselbasid

)delbasidNEPO(tceffeoN

Page is loading ...

ENGLISH

Read the instructions carefully before using the product and store

them for future use

GENERAL SAFETY REGULATIONS

If correctly installed and used, the STEP-T automated system ensures

a high degree of safety.

Some simple rules on behaviour can prevent accidental trouble:

• Do not pass through the gate when it is moving. Wait for the

gate to open fully before passing through it.

• Do not, on any account, stand in the gate's movement range.

• Do not stand near the automated system or allow children,

persons or things to stand or lie there, especially while it is in use.

• Keep remote controls or other pulse generators away from

children, to prevent the automated system from being activated

involuntarily.

• Do not allow children to play with the automated system.

• Do not willingly obstruct gate movement.

• Prevent any branches or shrubs from interfering with gate

movement.

• Keep indicator-lights efficient and easy to see.

• Do not attempt to activate the gate by hand unless you have

released it.

• In the event of malfunctions, release the gearmotor to allow

access and wait for qualified technical personnel to do the

necessary work.

• Before using the manual release, disconnect the batteries.

• Do not in any way modify the components of the automated

system.

• Do not attempt any kind of repair or direct action whatever

and contact qualified personnel only.

• At least every six months: arrange a check of the automated

system, safety devices and accessories.

DESCRIPTION

These instructions apply to the following model:

GENIUS STEP-T

The STEP-T automated system for residential sliding gates consists of

a non-reversing electro-mechanical operator, powered on 12 Vdc,

coupled to a control board with a work battery (not a black-out

battery), ensuring operation even in the event of a mains power

cut.

The non-reversing system guarantees the gate will automatically

lock when the motor is not operating. A release system enables

the gate to be moved by hand in case of malfunction.

The gearmotor is controlled by an electronic control unit housed

inside the gearmotor where it is adequately protected against

atmospheric agents.

The gates is normally in its closed position.

When the electronic control unit receives an opening command

via the radio control or any other pulse generator, it activates the

gearmotor to move the gate until it reaches the opening position

to allow access.

If automatic mode was set, the leaves closes automatically after

the selected pause time has elapsed.

If the semi-automatic mode was set, a second pulse must be sent

to close the gate again.

A stop pulse (if supplied) always stops movement.

For details on the behaviour of the automated system in different

function logics, consult the installation Technician.

Automated systems include safety devices that prevent the gate

from moving when there is an obstacle in the area they protect.

The STEP-T automated system is provided with an adjustable anti-

crushing device which reverses gate movement in case of contact

with an obstacle.

The warning-light indicates that the gate is currently moving.

MANUAL OPERATION

If the gate has to be moved manually due to a fault of the

automated system, use the release device as follows:

• Open the protective door with a coin.

• Take the supplied key located inside the door, fit it in the release

system and turn it clockwise until it reaches the mechanical stop

(Fig. 1).

• Open or close the gate manually.

RESTORING NORMAL OPERATION MODE

• Manually take the gate back to its closed position.

• Turn the release key anti-clockwise until it reaches the

mechanical stop (Fig. 2).

• Move the gate until the release meshes.

• Remove the release key and put it back in its place; close the

protective door.

FRANÇAIS

Lire attentivement les instructions avant d'utiliser le produit et les

conserver pour toute nécessité future.

NORMES GENERALES DE SECURITE

S'il est correctement installé et utilisé, l'automatisme STEP-T garantit

un haut niveau de sécurité.

Par ailleurs quelques normes simples de comportement peuvent

éviter les accidents:

• Ne pas transiter par le portail quand ce dernier est en

mouvement. Avant de transiter par le portail, attendre l'ouvertu-

re complète.

• Ne stationner en aucun cas sur la voie du mouvement du portail.

• Ne pas stationner et interdire aux enfants et aux tiers de stationner

près de l'automatisme; ne pas y interposer d'objets; respecter

plus encore cette norme durant le fonctionnement.

• Eloigner de la portée des enfants les radiocommandes ou tout

autre générateur d'impulsions, pour éviter tout actionnement

involontaire de l'automatisme.

• Interdire aux enfants de jouer avec l'automatisme.

• Ne pas empêcher volontairement le mouvement du portail.

• Eviter que des branches ou des arbustes n’entravent le

mouvement du portail.

• Faire en sorte que les systèmes de signalisation lumineuse soient

toujours fiables et bien visibles.

• N’actionner manuellement le portail qu’après l’avoir

déverrouillé.

• En cas de dysfonctionnement, déverrouiller le motoréducteur

pour permettre l’accès et attendre l’intervention technique du

personnel qualifié.

• Avant d'intervenir sur le déverrouillage manuel, débrancher les

batteries.

• Ne jamais modifier les composants faisant partie du système

d'automatisme.

•Eviter toute tentative de réparation ou d'intervention directe et

s'adresser uniquement à un personnel qualifié.

• Faire vérifier, tous les six mois au moins, la fiabilité de l'automatisme,

des dispositifs de sécurité et des accessoires.

DESCRIPTION

Ces instructions sont valables pour le modèle suivant:

GENIUS STEP-T

L’automatisme STEP-T pour portails coulissants domestiques est

constitué par un opérateur électromécanique irréversible,

alimenté à 12 Vcc et associé à une armoire électronique dotée

d'une batterie de fonctionnement (et non pas de black-out), qui

garantit le fonctionnement de l'automatisme même en cas de

coupure de courant.

Le système irréversible garantit le blocage mécanique du portail

quand le moteur n'est pas en fonction. Un déverrouillage manuel

permet de manœuvrer le portail en cas de dysfonctionnement.

Le fonctionnement du motoréducteur est géré par une centrale

électronique de commande, logée à l'intérieur du motoréducteur

avec un degré de protection adéquat contre les agents

atmosphériques.

Le portail se trouve normalement en position de fermeture.

Quand la centrale électronique reçoit une commande d'ouver-

ture par l'intermédiaire de la radiocommande ou de tout autre

générateur d'impulsion, elle actionne le motoréducteur obtenant

le mouvement du portail, jusqu'à la position d'ouverture qui permet

l'accès.

Si on a sélectionné le fonctionnement automatique, les vantaux

se referment d'eux-mêmes au bout du temps de pause sélectionné.

Si on a sélectionné le fonctionnement semi-automatique, envoyer

une deuxième impulsion pour obtenir la refermeture.

Une impulsion de stop (si prévue) arrête toujours le mouvement.

Pour le comportement détaillé de l'automatisme dans les

différentes logiques de fonctionnement, contacter l'Installateur.

Les automatismes comprennent des dispositifs de sécurité qui

empêchent le mouvement du portail quand un obstacle se trouve

dans la zone qu'ils protègent.

L'automatisme STEP-T est doté d'un dispositif réglable d'anti-

écrasement qui, en cas de contact avec un obstacle, invertit le

mouvement du portail.

La signalisation lumineuse indique le mouvement en cours du

portail.

Page is loading ...

Genius STEP T Operating instructions

Brand: Genius

Model: STEP T

Category: Gate Opener

Type: Operating instructions

Download PDF

report

in other languages

italiano: Genius STEP T Istruzioni per l'uso
français: Genius STEP T Mode d'emploi
español: Genius STEP T Instrucciones de operación
Deutsch: Genius STEP T Bedienungsanleitung
Nederlands: Genius STEP T Handleiding

Genius STEP T Operating instructions

Genius STEP T Operating instructions

in other languages

Related papers

Other documents