Glacier Bay 67574-6001 Installation guide

THANK YOU

USE AND CARE GUIDE

TWO-HANDLE LAVATORY FAUCET

Questions, problems, missing parts? Before returning to the store,

call Glacier Bay Customer Service

8 a.m. - 6 p.m., EST, Monday - Friday

1-855-HD-GLACIER

HOMEDEPOT.COM

Model #67574-6001

67574-6004

67574-6016

faucet. We strive to continually create quality products designed to enhance your home. Visit us online to see

our full line of products available for your home improvement needs. Thank you for choosing Glacier Bay!

REV.01YOW

2

Table of Contents

Safety Information ....................................2

Warranty ...................................................2

Pre-Installation .........................................2

Planning Installation ..............................2

Tools Required .......................................2

Package Contents ..................................3

Installation ................................................4

Operation...................................................7

Care and Cleaning ....................................8

Service Parts

...........................................

8

Safety Information

Please read and understand this entire manual before

attempting to assemble, operate, or install the product.

CAUTION: Always turn off the water supply before

removing an existing faucet or replacing any part of a

faucet. Open the faucet handle to relieve water pressure

and ensure that the water is completely shut off.

Warranty

LIMITED LIFETIME WARRANTY

Glacier Bay products are manufactured with superior quality standards and workmanship and are backed by our

limited lifetime warranty. Glacier Bay products are warranted to the original consumer purchaser to be free of

defects in materials or workmanship. We will replace FREE OF CHARGE any product or parts that proves defective.

Simply, return the product / part to any of The Home Depot retail locations or call 1-855-HD-GLACIER (1-855-434-

5224) to receive the replacement item. Proof of purchase (original sales receipt) from the original consumer

purchaser must be made available for all Glacier Bay warranty claims.

This warranty excludes incidental/inconsequential damages and failures due to misuse, abuse or normal wear and

tear. This warranty excludes all industrial, commercial & business usage, whose purchasers are hereby, extended

duration of warranty.

Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitations may not apply to you. This warranty gives you specic legal rights and you may also have other

rights that vary from state to state and province to province. Please see a store or contact 1-855-HD-GLACIER for

more details.

Adjustable

wrench

Safety

goggles

Phillips

screwdriver

SILICONE

Silicone

(2) Supply

lines

Basin

wrench

Pre-Installation

PLANNING INSTALLATION

TOOLS REQUIRED

Before beginning the installation of this product, ensure all parts are present. Compare parts with the Package

Contents section. If any part is missing or damaged, do not attempt to install the product.

3

Pre-Installation (continued)

PACKAGE CONTENTS

HOMEDEPOT.COM

Please contact 1-855-HD-GLACIER for further assistance.

Part Description Quantity

A 1

B Hot end valve 1

C Cold end valve 1

J

Quick connect

assembly

1

Spout assembly

D 2

E Nut 2

F Screw 4

Washer

G 1

H

Washer

1

I

Nut

K

1Stopper

L

1Flange

M

1Gasket

N

1Nut

O

1Pop-up body

P

1Pivot nut

Q

1Horizontal rod

R

1Clip

T

1Strap

S

1Screw

Part Description Quantity

1Lift rod assembly

A

B

C

D

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

E

4

Installation

1

Installing the spout assembly

CAUTION: Always turn off the water supply before

removing an existing faucet or replacing any part of a

faucet. Open the faucet handle to relieve water pressure

and ensure that the water is completely shut off.

□ Shut off the water supply.

□ Place the spout assembly (A) through the middle

mounting hole in the sink.

□ Secure the spout assembly (A) with the washer

(G) and the nut (H). Use the basin wrench to

tighten the nut (H).

2

Connecting the hot and cold

valves

□ Slide the hot and cold end valves (B & C) through

the sink mounting holes. Make sure the long

tubes are installed away from the spout

assembly (A).

□ Secure the end valves (B & C) with the washers

(D) and the nuts (E). Hand tighten the nuts (E)

onto the end valve (B & C) shanks. Lock the nuts

(E) into position by tightening the screws (F) with

a phillips screwdriver.

NOTE: The hot side end valve is labeled.

H

G

A

C

B

F

D

E

HOMEDEPOT.COM

Please contact 1-855-HD-GLACIER for further assistance.

5

Installation (continued)

3

Connecting the hose

□ Align the tabs (1 & 2) on the quick connect

assembly (I).

□ Push the quick connect assembly (I) rmly

upward and snap it onto the receiving tube tab.

Pull down moderately to ensure the connection

has been made.

□ If it is necessary to remove the quick connect

assembly (J), squeeze the tabs on the hose,

and then pull down to disconnect.

4

Making the waterline

connections

NOTE: The hot side inlet tube is indicated by a label.

If the label is not present, the hot supply tube is the longer

of the two inlet tubes.

□ Use 1/2 in. I.P.S. faucet connections (2), or use

supply line coupling nuts (3) (not included) with

a 3/8 in. O.D. ball-nose riser (1).

NOTE: Before tightening the faucet connector to the water

supply, apply a second wrench to the supply tube tting.

This will prevent the supply tube from moving or twisting

when tightening the faucet connector. Do not overtighten.

1

I

2

3

1

2

6

Installation (continued)

Installing the horizontal rod,

stopper, and strap

5

Preparing the pop-up assembly

□ Remove the stopper (J) and the ange (K).

□ Screw the nut (M) all the way down, and push the

gasket (L) down.

7

□ Remove the pivot nut (O).

□ Install the horizontal rod (P) and the stopper (J),

as shown (1).

□ Hand tighten the pivot nut (O).

□ Attach the horizontal rod (P) to the strap (S)

using the clip (Q).

6

Installing the pop-up body and

pop-up flange

□ Apply silicone to the underside of the ange (K).

□ Insert the pop-up body (N) into the sink. Screw

the ange (K) onto the pop-up body (N). The pivot

hole (1) must face the back of the sink.

□ Use the groove joint pliers to tighten the nut (M),

but do not over tighten. Do not turn the pop-up

body (N) while tightening the nut (M) or the

sealant may not seal properly. Clean away

any excess putty.

K

J

M

L

N

1

M

SILICONE

K

O

P

J

1

S

Q

7

Installation (continued)

8

Installing the lift rod

□ Insert the lift rod (T) through the spout

assembly (A) and into the strap (S).

□ Tighten the screw (R).

HOMEDEPOT.COM

Please contact 1-855-HD-GLACIER for further assistance.

1

Flushing and checking for leaks

□ Turn on the water supply and allow both hot

and cold water to run for at least one minute

each. This ushes away any debris that could

cause damage to internal parts.

□ While the water is running, check for leaks.

□ Turn off the water and replace the aerator.

Operation

A

T

R

S

1

9

Remove the quick connector

□ If it is necessary to remove the quick connector

(1), squeeze the tabs (2) on the quick connector

and then pull down to disconnect.

Squeeze

Pull

down

1

2

IMPORTANT: After installation is complete, remove the

aerator to ush the water lines. Do not lose the gasket (1) in

the aerator.

8

Care and Cleaning

□

□ Do not use abrasive cleaners when cleaning this faucet.

Service Parts

*Specify Finish

Part Description Part Number

1

RP13188*

2 Screw RP50169

3

4

5

6

7

Cartridge (H) RP20035

8

Cartridge (C) RP20036

9

Flange

RP80291*

Handle

14

Nut RP56059

O-ring RP60002

Part Description Part Number

10

11

12

Washer

RP64147

15

Screw RP50004

16

Aerator RP30060*

17

Washer RP70228

Nut RP56091

Bonnet RP70435 Block RP70421

19 Lift rod & lift rod knob RP40118*

20

Pop-up assembly less

lift rod

RP40027*

18

Quick connect

assembly

RP70430

13

O-ring RP60020

Handle seat RP17148*

Index RP80242*

1

2

3

4

5

6

7

8

9

10

11

12

14

15

16

17

18

13

19

20

Questions, problems, missing parts? Before returning to the store,

call Glacier Bay Customer Service

8 a.m. - 6 p.m., EST, Monday - Friday

1-855-HD-GLACIER

HOMEDEPOT.COM

Retain this manual for future use.

Page is loading ...

Glacier Bay 67574-6001 Installation guide

Glacier Bay 67574-6001 Installation guide

in other languages

Related papers

Other documents