Parkside PBSA 12 A1 Original Instruction

CORDLESS DRILL PBSA 12 A1

IAN 273457

CORDLESS DRILL

Translation of the original instructions

AKKUPORAKONE

Alkuperäisen käyttöohjeen käännös

AKKU-BOHRSCHRAUBER

Originalbetriebsanleitung

WIERTARKO-WKRĘTARKA

AKUMULATOROWA

Tłumaczenie oryginalnej instrukcji obsługi

SLADDLÖS BORRSKRUVDRAGARE

Översättning av bruksanvisning i original

273457_par_Akku-Bohrschrauber_cover_FI_PL.indd 2 19.01.16 11:50

GB / IE Translation of the original instructions Page 4

FI Alkuperäisen käyttöohjeen käännös Sivu 17

SE Översättning av bruksanvisning i original Sidan 31

PL Tłumaczenie oryginalnej instrukcji obsługi Strona 44

DE / AT / CH Originalbetriebsanleitung Seite 59

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the

device.

Käännä ennen lukemista kuvallinen sivu esiin ja tutustu seuraavaksi laitteen kaikkiin toimintoihin.

Vik ut bildsidan och ha den till hands när du läser igenom anvisningarna och gör dig bekant med

apparatens / maskinens funktioner.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi

funkcjami urządzenia.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

273457_par_Akku-Bohrschrauber_cover_FI_PL.indd 3 19.01.16 11:50

12

3

4

12

5

6

7

8

13

1415

15

16

8

9

1011

4

G B I E

Content

Introduction .................................4

Intended purpose .........................4

General description ......................5

Extent of the delivery ........................5

Overview ........................................5

Functional description .......................5

Technical data ..............................5

Safety instructions ........................6

Symbols and icons ...........................6

General safety instructions for power

tools ...............................................7

Charging the battery ..................11

Inserting/removing the battery .........11

Recharging the battery ....................11

Used batteries ...............................12

Checking the battery charge level ....12

Operation ..................................12

Choice of gear ..............................12

Set the direction of rotation .............12

Torque setting ................................12

Tool change ..................................13

Keyless drill chuck removal ..............13

Using the bitholder .........................13

Switching on/off ............................13

Cleaning and maintenance .........14

Cleaning .......................................14

Maintenance .................................14

Storage ...................................... 14

Disposal and protection of the

environment .............................. 14

Replacement parts/accessories ...15

Guarantee .................................15

Repair Service ............................16

Service-Center ............................ 16

Importer ....................................16

Translation of the original EC

declaration of conformity ............75

Introduction

Congratulations on the purchase of your

new device. With it, you have chosen a

high quality product.

During production, this equipment has

been checked for quality and subjected to

a nal inspection. The functionality of your

equipment is therefore guaranteed.

The operating instructions constitute

part of this product. They contain

important information on safety, use

and disposal.

Before using the product, familiarise

yourself with all of the operating

and safety instructions. Use the

product only as described and for

the applications specied.

Keep this manual safely and in the

event that the product is passed on,

hand over all documents to the third

party.

Intended purpose

The device is intended for drilling screws

in and out and for drilling holes in wood,

metal or plastic.

Any other use that is not explicitly ap-

proved in these instructions may result in

damage to the equipment and represent a

serious danger to the user.

The user or operator is responsible for ac-

cidents causing injury to other people or

damage to property.

This equipment is not suitable for commer-

cial use. Commercial use will invalidate the

guarantee.

5

G B I E

General description

The illustrations are on the

front and back fold-out

page.

Extent of the delivery

Carefully unpack the appliance and check

that it is complete:

- Cordless Drill

- Battery-charger

- Battery

- Storage case

- Instruction Manual

Pictured bit and drill not included.

Overview

1 Keyless drill chuck

2 Chuck ring

3 Torque adjustment ring

4 Battery Indicator

5 Speed selector

6 Direction of rotation switch

7 Battery

8 Battery release button

9 On/off switch

10 LED working light

11 Drill chuck aperture

12 Storage case

13 Charger

14 Charger power supply cord

15 Green LED

16 Red LED

17 Bitholder

Functional description

The cordless drill with two-speed gearing

has a 19+1 level torque adjustment, left/

right running, a removable keyless chuck,

a 6-point bitholder and an LED working

light.

Technical data

Appliance

Motor voltage ............................. 12 V

Idling speed

1st gear .............................0-350 min

-1

2nd gear .........................0-1200 min

-1

Maximum torque ..........................25 Nm

Span-chuck ............................ 0.8-10 mm

Weight (without battery charger) .....1.1 kg

Drilling capacity

for wood .......................... max. 25 mm

for steel ............................. max. 8 mm

Sound power level

(L

pA

) ......................66.5 dB(A); K= 3 dB

Sound power level

(L

WA

) ........................ 77.5 dB(A); K= 3 dB

Vibration (a

h

)

Drilling in metal ...................< 2.5 m/s

2

Screwdriving without impact .. < 2.5 m/s

2

K= 1.5 m/s

2

Battery (Li-Ion) ............ DCBK-70-12

Nominal voltage ......................... 12 V

Capacity ..................................... 1.5 Ah

Charging time ...................... approx. 1 h

Recharger ............ JLH201261500G

Nominal consumption .....................30 W

Uptake voltage/Input

........................... 100-240 V~, 50-60 Hz

Voltage output/Output

.................................12.6 V

1500 mA

Protection class ................................

II

Protection category ......................... IPX0

6

G B I E

Noise and vibration values have been

determined according to the standards and

regulations mentioned in the declaration of

conformity.

Technical and optical changes may be

undertaken in the course of further devel-

opment without notice. All dimensions,

references and information in this instruc-

tion manual are therefore not guaranteed.

Legal claims made on the basis of the

instruction manual can therefore not be

considered as valid.

The stated vibration emission value was

measured in accordance with a standard

testing procedure and may be used to com-

pare one power tool to another.

The stated vibration emission value may

also be used for a preliminary exposure

assessment.

Warning: The vibration emission

value may differ during actual use

of the power tool from the stated

value depending on the manner in

which the power tool is used.

Safety precautions aimed at protect-

ing the user should be based on esti-

mated exposure under actual usage

conditions (all parts of the operating

cycle are to be considered, includ-

ing, for example, times during which

the power tool is turned off and

times when the tool is turned on but

is running idle).

Safety instructions

Ensure that the safety instructions are ob-

served when operating the appliance.

Symbols and icons

Symbols on the appliance:

Carefully read these operating in-

structions.

Electrical appliances must not be dis-

posed of with the domestic waste.

Symbols on the battery:

Carefully read these operating in-

structions.

Do not dispose of

batteries in house-

hold waste, re or

water.

Do not subject the battery to strong

sunlight over long periods and

do not leave it on a heater (max.

45°C).

Take batteries to an old battery

collection point where they will

be recycled in an environmentally

friendly manner.

Store the battery in charged

condition

The battery requires an ambient

temperature of

+10°C to + 40°C.

The battery should never come into

contact with water.

7

G B I E

General safety instructions

for power tools

WARNING! Read all safety

directions and instructions.

Omissions in the compliance with

safety directions and instructions

can cause electrical shock, re

and/or severe injuries.

Retain all safety directions and in-

structions for future use.

The term “Power Tools” used in the safety

instructions refers to mains-operated power

tools (with power cord) and to battery-oper-

ated power tools (without power cord).

1) WORK AREA SAFETY

a) Keep work area clean and well

lit. Cluttered or dark areas invite acci-

dents.

b) Do not operate power tools in

explosive atmospheres, such as

in the presence of ammable

Iiquids, gases or dust. Power tools

create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders

away while operating a power

tool. Distractions can cause you to lose

control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the

outlet. Never modify the plug in

any way. Do not use any adapter

plugs with earthed (grounded)

power tools. Unmodied plugs and

matching outlets will reduce risk of electric

shock.

b) Avoid body contact with earthed

or grounded surfaces, such as

Symbols on the recharger:

Warning!

Before using for the rst time, care-

fully read through the user manual.

The recharger is for indoor use

only.

T2A

Miniature fuse

Protection class II

Electrical appliances must not be dis-

posed of with the domestic waste.

LED display while

charging.

Symbols in the manual

Warning symbols with in-

formation on damage and

injury prevention.

Instruction symbols (the instruction

is explained at the place of the

exclamation mark) with information

on preventing damage.

Help symbols with information on

improving tool handling.

8

G B I E

pipes, radiators, ranges and re-

frigerators. There is an increased risk

of electric shock if your body is earthed

or grounded.

c) Do not expose power tools to rain

or wet conditions. Water entering a

power tool will increase the risk of electric

shock.

d) Do not abuse the cord. Never use

the cord for carrying, pulling or

unplugging the power tool. Keep

cord away from heat, oil, sharp

edges or moving parts. Damaged

or entangled cords increase the risk of

electric shock.

e) When operating a power tool

outdoors, use an extension cord

suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a

damp location is unavoidable,

use a residual current device

(RCD) protected supply. Use of an

RCD reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are

doing and use common sense

when operating a power tool. Do

not use a power tool while you

are tired or under the inuence

of drugs, alcohol or medication.

A moment of inattention white operating

power tools may result in serious personal

injury.

b) Use personal protective equip-

ment. Always wear eye protec-

tion. Protective equipment such as dust

mask, non-slip safety shoes, hard hat, or

hearing protection used for appropriate

conditions will reduce personal injuries.

c) Prevent unintentional starting.

Ensure the switch is in the off-po-

sition before connecting to power

source and/or battery pack,

picking up or carrying the tool.

Carrying power tools with your nger on

the switch or energising power tools that

have the switch on invites accidents.

d) Remove any adjusting key or

wrench before turning the power

tool on. A wrench or a key left attached

to a rotating part of the power tool may

result in personal injury.

e) Do not overreach. Keep proper

footing and balance at all times.

This enables better control of the power

tool in unexpected situations.

f) Dress properly. Do not wear loose

clothing or jewellery. Keep your

hair, clothing and gloves away

from moving parts. Loose clothes,

jewellery or long hair can be caught in

moving parts.

g) If devices are provided for the

connection of dust extraction and

collection facilities, ensure these

are connected and properly used.

Use of dust collection can reduce dust-

related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use

the correct power tool for your

application. The correct power tool will

do the job better and safer at the rate for

which it was designed.

b) Do not use the power tool if the

switch does not turn it on and off.

Any power tool that cannot be controlled

with the switch is dangerous and must be

repaired.

c) Disconnect the plug from the

9

G B I E

power source and/or the bat-

tery pack from the power tool

before making any adjust -ments,

changing accessories, or storing

power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentaIly.

d) Store idle power tools out of the

reach of children and do not al-

low persons unfamiliar with the

power tool or these instructions to

operate the power tool. Power tools

are dangerous in the hands of untrained

users.

e) Maintain power tools. Check for

misalignment or binding of mov-

ing parts, breakage of parts and

any other condition that may af-

fect the power tool’s operation. If

damaged, have the power tool repaired

before use. Many accidents are caused

by poorly maintained power tools.

f) Keep cutting tools sharp and

clean. Properly maintained cutting tools

with sharp cutting edges are less Iikely to

bind and are easier to control.

g) Use the power tool, accessories

and tool bits etc. in accordance

with these instructions, taking into

account the working conditions

and the work to be performed.

Use of the power tool for operations dif-

ferent from those intended could result in

a hazardous situation.

h) Hold the device by the insulated

gripping surfaces when per-

forming work in which the cut-

ting tool may come into contact

with hidden wiring or its own

cord. Contact with a live wire can also

cause a charge in metal parts of the

device and result in an electric shock.

5) CAREFUL HANDLING AND USE OF

BATTERY DEVICES

a) Charge the batteries only in

chargers that are recommended

by the manufacturer. Risk of re if a

charger that is suitable for a specic type

of battery is used with other batteries.

b) In the power tools, use only the

batteries designed for the pur-

pose. The use of other batteries may

result in injuries and risk of re.

c) Keep the unused battery away

from paper clips, coins, keys,

nails, screws and other small

metal objects, which could cause

bridging of the contacts. A short

circuit between the battery contacts may

cause burns or re.

d) If used incorrectly, liquid may

leak from the battery. Avoid

contact with this. In the event of

accidental contact, rinse off with

water. If the liquid gets into eyes,

seek medical assistance. Leaking

battery uid may cause skin irritations or

burns.

6) SERVICE

Have your power tool serviced by

a qualied repair person using

only identical replacement parts.

This will ensure that the safety of the

power tool is maintained.

7) SPECIAL SAFETY DIRECTIONS FOR

BATTERY-OPERATED TOOLS

a) Ensure that the device is switched

off before inserting the battery.

Inserting a battery into a power tool that

is switched on may result in accidents.

b) Recharge the batteries indoors

1 0

G B I E

only because the battery charger

is designed for indoor use only.

c) To reduce the electric shock haz-

ard, unplug the battery charger

from the mains before cleaning

the charger.

d) Do not subject the battery to

strong sunlight over long periods

and do not leave it on a heater.

Heat damages the battery and there is a

risk of explosion.

e) Allow a hot battery to cool before

charging.

f) Do not open up the battery and

avoid mechanical damage to the

battery. Risk of short circuit and fumes

may be emitted that irritate the respiratory

tract. Ensure fresh air and seek medical

assistance in the event of discomfort.

g) Do not use non-rechargeable bat-

teries!

8) CORRECT HANDLING OF THE BAT-

TERY CHARGER

• This appliance can be used by children

aged from 8 years and above and per-

sons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use

of the appliance in a safe way and un-

derstand the hazards involved. Children

shall not play with the appliance. Clean-

ing and user maintenance shall not be

made by children without supervision.

• To charge the battery, use only

the charger supplied. Risk of re and

explosion. This ensures that the safety of

the device is maintained.

• Before each use, check the charg-

er, cable and plug and have them

repaired by qualied profession-

als and only with original parts.

Do not use a defective charger and do

not open it up yourself. This ensures that

the safety of the device is maintained.

• Connect the charger only to a

socket with an earth. Ensure that

the mains voltage matches the

specications on the charger rat-

ing plate. Risk of electric shock.

• Disconnect the charger from the

mains before closing or opening

connection to the battery / power

tool / device.

• Keep the charger clean and away

from wet and rain. Do not use

the charger outdoors. Dirt and the

entry of water increase the risk of electric

shock.

• Operate the charger only with

the appropriate original batteries.

Charging other batteries may result in

injuries and risk of re.

• Avoid mechanical damage to the

charger. This can result in internal short

circuits.

• Do not operate the charger on a

combustible surface (e.g. paper,

textiles). Risk of re due to heating dur-

ing charging.

• If the power cable for this equipment is

damaged, it must be replaced by the

manufacturer, a customer service agent of

the same or a similarly qualied person in

order to prevent hazards.

• The battery of the appliance is not fully

charged at the time of delivery. It there-

fore needs to be fully recharged before

you use it for the rst time. Slot the bat-

tery into the base and plug the battery

charger into a mains outlet.

• When the battery is fully charged, unplug

the charger from the mains and from the

appliance.

• Do not use the charger to charge non-

rechargeable batteries.

1 1

G B I E

9) RESIDUAL RISKS

Even if properly operating and handling this

electric tool, some residual risks will remain.

Due to its construction and build, this electric

tool may present the following hazards:

a) Cuts

b) Ear damage if working without ear protec-

tion.

c) Damage to your health caused by swing-

ing your hands and arms when operating

the appliance for longer periods of time or

if the unit is not held or maintained prop-

erly.

Warning! During operation, this

electric tool generates an electromag-

netic eld which, under certain circum-

stances, may impair the functionality of

active or passive medical implants. To

reduce the risk of serious or lethal inju-

ries, we recommend that persons with

medical implants consult their doctor

and the manufacturer of their medical

implant before operating the machine.

Charging the battery

Do not expose the battery to

extreme conditions such as

heat or impact. Risk of injury

from escaping electrolytic so-

lution! After eye/skin contact,

rinse the affected areas with

water or a neutraliser and

consult a doctor.

Charge the battery in a dry

room only.

Prior to attaching the charger,

check that the battery‘s outer

surface is clean and dry.

There is a risk of injury due to

electric shock.

Only use the original charger from

the package to charge the battery.

• Charge the battery before the rst time

of use. Do not briey charge the bat-

tery several time in a row.

• Recharge the battery when you notice

that the appliance is becoming slower.

• If a fully recharged battery lasts for

considerably shorter operating times,

the battery is used up and needs to

be replaced. Only use an OEM spare

battery available from our Customer

Service.

• Always take heed of the applicable

safety instructions as well as the envi-

ronmental protection regulations and

information.

• The warranty excludes all defects

caused by improper handling.

Inserting/removing the

battery

1. To insert the battery (7), place it

on the guide track and push it

back into the appliance. It will

audibly snap in.

2. To remove the battery (7) from the

appliance, press the release but-

tons (8) on the battery and pull

out the battery.

Recharging the battery

1. Remove the battery (7) from the

appliance i necessary.

2. Insert the battery (7) in the charg-

ing compartment of the battery

charger (13). It will audibly snap

in.

3. Plug the battery charger (13) into

a mains outlet.

1 2

G B I E

4. When the battery is fully re-

charged unplug the battery

charger (13) from the mains.

5. Pull the battery (7)out of the bat-

tery charger (13).

Overview of the LED indicators on

the charger (13):

Green LED (15) lights up

without battery inserted:

Charger ready.

Green LED (15) lights up:

Battery such alleged

charged.

Red LED (16) lights up:

Battery charging.

Used batteries

• If a fully recharged battery lasts for

considerably shorter operating times,

the battery is used up and needs to be

replaced. Only use an OEM battery

pack replacement available from our

Customer Service.

• Always take heed of the applicable

safety instructions as well as the envi-

ronmental protection regulations and

information (see “Cleaning and Main-

tenance”).

Checking the battery charge

level

The battery’s ( 7) charge level is indi-

cated by the charge state indicator (

4).

The LEDs indicate the battery’s charge

level, when the device is in operation.

red-yellow-green => Battery fully

charged

red and yellow => Battery half charged

red => Battery needs to be

charged

Operation

Choice of gear

Slide the gear selector (5) to 1 or

2, corresponding to a low or high

torque selection.

A gear change may only be per-

formed in standstill mode!

Set the direction of rotation

You can select the direction of rotation with

the direction switch (clockwise and anti-

clockwise direction) and secure the device

against accidental start up.

1. Wait for the device to shut-down.

2. Clockwise direction:

Press direction switch (6) to

the right.

3. Anticlockwise direction:

Press direction switch (6) to

the left.

4. Switch lock: Bring direction switch

to neutral position.

The direction changed may only be

performed in standstill mode.

Torque setting

You can preset the maximum torque by ro-

tating the torque adjustment ring (3).

19+1 torque levels are provided.

1 3

G B I E

1. Turn the adjusting ring (3) to se-

lect the desired torque:

Step 1 --> lowest torque,

Step

--> highest torque.

Screws: Steps 1 - 19

Drilling: Step

.

2. Start with a lower torque step

and increase according to re-

quirement.

Torque adjustment should only be

performed in standstill mode.

Reaching the preset torque limit pro-

duces a noticeable rasping sound.

This sound is caused by the slip

clutch.

Tool change

1. Rotate the keyless chuck (1) coun-

ter-clockwise, until the drill chuck

aperture (11) is large enough to

accommodate the tool.

2. Push the tool as far as possible

into the keyless chuck (1).

3. Rotate the chuck clockwise to

clamp the tool rmly.

4. To remove the tool again, rotate

the keyless chuck (1) and pull out

the tool.

Keyless drill chuck removal

To use the bitholder (17), you must remove

the keyless chuck (1).

1. Hold the keyless chuck (1) tightly

from the front. Pull or push the

drill chuck ring (2) in the direction

of the keyless chuck (1).

2. This unlocks the keyless chuck (1)

and it can be pulled off from the

front.

3. In order to put the keyless chuck

(1) back in position, pull the drill

chuck ring (2) in the direction of

the keyless chuck. Push the key-

less chuck (1) on as far as it will

go.

If the keyless chuck (1) does not

engage automatically, turn the drill

chuck ring (2).

Using the bitholder

After removing the keyless chuck (1) you

can use the bitholder (17).

1. Insert a suitable 6-point bit in the

bitholder (17). Because of the

6-point bit holder, it may be that

you need to rotate the bit slightly.

2. Slide the bit right into the bithold-

er (17). The bit is held rmly

by the duct and the magnetic

bitholder.

3. To remove the bit, simply remove

the bit from the bitholder (17).

Switching on/off

By using the on/off switch (9) you can

progressively control the speed. The longer

you push the on-off button, the higher the

speed.

1. Press the on/off switch (9) to start

the device. The LED work light

(10) lights up during operation.

2. To turn it off, release the on/off

switch (9).

When you move the direction

switch (6) to the middle position,

the device is secured against be-

ing switched on.

1 4

G B I E

Cleaning and

maintenance

Contact our Service Centre about

repairs and servicing not described

in this manual. Only use OEM

parts. Risk of injury!

Turn off the appliance and, before

doing any servicing, remove the

battery.

The following cleaning and servicing

should be done regularly. This will ensure

a long and reliable service life.

Cleaning

Do not spray the appliance

with water and do not im-

merse it in water. Electric

shock hazard!

• Keep clean the ventilation slots, motor

housing and handles of the appliance.

Use a damp cloth or a brush.

Do not use cleaning agents or solvents.

You may otherwise irreparably dam-

age the appliance.

Maintenance

The appliance cleaner is maintenance free.

Storage

• Store the equipment in a dry place

well out of reach of children.

• Store the equipment between 10° C

and 40° C. During storage, avoid ex-

treme cold or heat so the battery does

not lose power.

• Remove the battery before storing the

unit for longer periods of time.

• During a longer storage period, check

the state of charge of the battery and

recharge if necessary roughly every

3months.

Disposal and protection

of the environment

Remove the battery from the device and

take the device, battery, accessories and

packaging for environmentally friendly

recycling.

Machines do not belong with domes-

tic waste.

Do not dispose of batteries in

household waste, re (risk of explo-

sion) or water. Damaged batteries

may damage the environment and

your health if toxic fumes or liquids

leak out.

• Return the unit to a recycling centre.

The plastics and metals in the unit can

be sorted and appropriately recycled.

Ask our Service Centre for details.

• Dispose of batteries in discharged condi-

tion. We recommend covering the pole

with adhesive tape to prevent a short

circuit. Do not open up the battery.

• Dispose of batteries in accordance with

the local regulations. Take batteries to

an old battery collection point where

they will be recycled in an environ-

mentally friendly manner. For informa-

tion about this, ask your local waste

management company or our service

centre.

• Defective units returned to us will be

disposed of for free.

1 5

G B I E

Replacement parts/

accessories

Spare parts and accessories

can be obtained at

www.grizzly-service.eu

If you do not have internet access, please

contact the Service Centre via telephone

(see “Service-Center” Page 16). Please

have the order number mentioned below

ready.

Keyless drill chuck (

1) ........ 91103353

Battery (

7) ....................... 80001133

Charger (

13) .................... 80001078

Guarantee

Dear Customer,

This equipment is provided with a 3-year

guarantee from the date of purchase.

In case of defects, you have statutory rights

against the seller of the product. These

statutory rights are not restricted by our

guarantee presented below.

Terms of Guarantee

The term of the guarantee begins on the

date of purchase. Please retain the original

receipt. This document is required as proof

of purchase.

If a material or manufacturing defect

occurs within three years of the date of

purchase of this product, we will repair or

replace – at our choice – the product for

you free of charge. This guarantee requires

the defective equipment and proof of pur-

chase to be presented within the three-year

period with a brief written description of

what constitutes the defect and when it oc-

curred.

If the defect is covered by our guarantee,

you will receive either the repaired product

or a new product. No new guarantee pe-

riod begins on repair or replacement of the

product.

Guarantee Period and Statutory

Claims for Defects

The guarantee period is not extended by

the guarantee service. This also applies for

replaced or repaired parts. Any damages

and defects already present at the time of

purchase must be reported immediately af-

ter unpacking. Repairs arising after expiry

of the guarantee period are chargeable.

Guarantee Cover

The equipment has been carefully pro-

duced in accordance with strict quality

guidelines and conscientiously checked

prior to delivery.

The guarantee applies for all material and

manufacturing defects. This guarantee

does not extend to cover product parts that

are subject to normal wear and may there-

fore be considered as wearing parts (e.g.

keyless drill chuck) or to cover damage to

breakable parts (e.g. switches, batteries).

This guarantee shall be invalid if the prod-

uct has been damaged, used incorrectly or

not maintained. Precise adherence to all of

the instructions specied in the operating

manual is required for proper use of the

product. Intended uses and actions against

which the operating manual advises or

warns must be categorically avoided.

The product is designed only for private

and not commercial use. The guarantee

will be invalidated in case of misuse or

improper handling, use of force, or inter-

ventions not undertaken by our authorised

service branch.

1 6

G B I E

Processing in Case of Guarantee

To ensure efcient handling of your query,

please follow the directions below:

• Please have the receipt and item num-

ber (IAN 273457) ready as proof of

purchase for all enquiries.

• Please nd the item number on the rat-

ing plate.

• Should functional errors or other de-

fects occur, please initially contact the

service department specied below by

telephone or by e-mail. You will then

receive further information on the pro-

cessing of your complaint.

• After consultation with our customer

service, a product recorded as defective

can be sent postage paid to the service

address communicated to you, with the

proof of purchase (receipt) and speci-

cation of what constitutes the defect

and when it occurred. In order to avoid

acceptance problems and additional

costs, please be sure to use only the ad-

dress communicated to you. Ensure that

the consignment is not sent carriage

forward or by bulky goods, express or

other special freight. Please send the

equipment inc. all accessories supplied

at the time of purchase and ensure ad-

equate, safe transport packaging.

Repair Service

For a charge, repairs not covered by

the guarantee can be carried out by

our service branch, which will be happy to

issue a cost estimate for you.

We can handle only equipment that has

been sent with adequate packaging and

postage.

Attention: Please send your equipment to

our service branch in clean condition and

with an indication of the defect.

Equipment sent carriage forward or by

bulky goods, express or other special

freight will not be accepted.

We will dispose of your defective devices

free of charge when you send them to us.

Service-Center

Service Great Britain

Tel.: 0871 5000 720

(£ 0.10/Min.)

E-Mail: [email protected]

IAN 273457

Service Ireland

Tel.: 1890 930 034

(0,08 EUR/Min., (peak))

(0,06 EUR/Min., (off peak))

E-Mail: [email protected]

IAN 273457

Importer

Please note that the following address is

not a service address. Please initially con-

tact the service centre specied above.

Grizzly Tools GmbH & Co. KG

Stockstädter Straße 20

63762 Großostheim

Germany

www.grizzly-service.eu

G B

I E

F I

1 7

Sisältö

Alkusanat ..................................17

Käyttötarkoitus ..........................17

Yleinen kuvaus .......................... 18

Toimituksen laajuus ......................... 18

Yleiskuva ...................................... 18

Toiminnon kuvaus ........................... 18

Tekniset tiedot ............................ 18

Turvallisuusmääräykset .............19

Symbolit ja kuvat .......................... 19

Sähkötyökaluja koskevat

turvallisuusohjeet ............................ 20

Lataus ........................................24

Akun asennus/poisto ...................... 24

Akun lataus ................................... 25

Käytetyt akut .................................. 25

Akun lataustilan tarkistus ................. 25

Käyttö .......................................25

Vaihteen valitseminen ..................... 25

Pyörimissuunnan asettaminen .......... 25

Vääntömomentin asettaminen .......... 26

Työkalun vaihtaminen ..................... 26

Pikakiristysistukan irrottaminen ......... 26

Ruuvauskärjen kiinnityksen käyttö ..... 26

Päälle- ja poiskytkentä .................... 27

Puhdistus ja huolto ....................27

Puhdistus ....................................... 27

Huolto .......................................... 27

Säilytys ...................................... 27

Hävitys/ympäristönsuojelu ........28

Varaosat/Tarvikkeet ..................28

Takuu ........................................29

Korjaus-huolto ...........................30

Service-Center ............................ 30

Maahantuoja .............................30

Alkuperäisen CE yhdenmukai-

suustodistuksen käännös ........... 75

Alkusanat

Onnittelumme uuden laitteen ostollesi.

Olet valinnut laadukkaan tuotteen.

Tämän laitteen laatua on tarkastettu val-

mistuksen aikana ja siihen on suoritettu

lopputarkastus. Laitteesi toimintakyky on

siten taattu.

Käyttöohje on tuotteeseen kuuluva

osa. Se sisältää tärkeitä turvalli-

suuteen, käyttöön ja laitteen hävit-

tämiseen liittyviä ohjeita. Tutustu

käyttö- ja turvallisuusohjeisiin ennen

tuotteen käyttöönottoa. Käytä tuotet-

ta vain ohjeiden mukaisesti ja vain

sille tarkoitettuun käyttöön.

Pidä käyttöohje tallessa ja luovuta

kaikki asiakirjat laitteen mukana

seuraavalle käyttäjälle.

Käyttötarkoitus

Laite on tarkoitettu ruuvien sisäänkiertämi-

seen ja irrottamiseen sekä puun, metallin

tai muovin poraamiseen. Kaikenlainen muu

käyttö, jota tässä käyttöohjeessa ei nimen-

omaan sallita, voi vioittaa laitetta ja aiheut-

taa käyttäjälle vakavia vaaratilanteita.

Käyttäjä on vastuussa tapaturmista tai va-

hingoista, jotka aiheutuvat muille henkilöil-

le tai näiden omaisuudelle.

Valmistaja ei vastaa vahingoista, jotka

aiheutuvat epäasianmukaisesta käytöstä tai

vääränlaisesta käsittelystä.

F I

1 8

Yleinen kuvaus

Kuvat ovat avattavilla etu-

että takasivuilla.

Toimituksen laajuus

Poista laite pakkauksesta ja tarkasta, onko

se täydellinen.

- Akkuporakone-ruuvinväännin

- Laturi

- Akku

- Säilytyslaukku

- Käyttöohje

Kuvan terät ja palat eivät sisälly toimituk-

seen.

Yleiskuva

1 Pikakiristysistukka

2 Istukkarengas

3 Vääntömomentin säätörengas

4 Akun lataustilan näyttö

5 Vaihteen valintakytkin

6 Pyörimissuunnan valintakytkin

7 Akku

8 Akun lukituspainike

9 Virtakytkin

10 LED-työvalo

11 Istukan aukko

12 Säilytyslaukku

13 Latauslaite

14 Latauslaitteen verkkoliitäntäjohto

15 Vihreä LED

16 Punainen LED

17 Ruuvauskärjen kiinnitys

Toiminnon kuvaus

Kaksivaihteisessa akkuporakone-ruuvin-

vääntimessä on 19+1 -tasoinen vääntö-

momentin säätö, pyörimissuunta oikealle/

vasemmalle, irrotettava pikakiristysistukka,

kuusiokulmakärjen kiinnitys sekä LED-työ-

valo.

Tekniset tiedot

Laite

Moottorijännite ........................... 12 V

Tyhjäkäyntikiertonopeus

1. vaihde ...........................0-350 min

-1

2. vaihde .........................0-1200 min

-1

Suurin vääntömomentti ..................25 Nm

Istukan kiristysleveys ............... 0,8-10 mm

Paino (ilman latauslaite) .................1,1 kg

Poran halkaisija puulle ......... enint. 25 mm

Poran halkaisija metallille ....... enint. 8 mm

Äänen painetaso

(L

pA

) .......................66,5 dB(A); K=3 dB

Äänitehotaso

(L

WA

) ......................77,5 dB(A); K=3 dB

Tärinä (a

h

) .............................................

Metallin poraaminen .............. < 2,5 m/s

2

Ruuvit ilman iskua................... < 2,5 m/s

2

K= 1,5 m/s

2

Akku (Li-Ion) ............... DCBK-70-12

Nimellisjännite ............................ 12 V

Kapasiteetti ................................. 1,5 Ah

Latausaika ......................................n 1 h

Laturi ................... JLH201261500G

Nimellisotto ...................................30 W

Tulojännite/Input

...........................100-240 V~, 50-60 Hz

Lähtöjännite/Output

.................................12,6 V

1500 mA

Suojaluokka ....................................

II

Suojatapa ...................................... IPX0

F I

1 9

Ilman työkaluja tehtävä ketjun kiristys

Melu- ja tärinäarvot on määritelty stan-

dard-inmukaisuustodistuksessa olevia nor-

meja ja määräyksiä vastaaviksi.

Teknisiä ja ulkonäköä koskevia muutoksia

laitteen kehityksen suhteen voidaan tehdä

ilmoittamatta niistä etukäteen. Kaikki tässä

käyttöohjeessa annetut mitat, viitteet ja

tiedot ovat ilman takuuta. Käyttöohjeesta

poikkeavia muutosvaatimuksia ei voida

hakea oikeusteitse.

Esitetty värähtelyn päästöarvo on mitattu

normitetun tarkistusmenettelyn mukaisesti

ja arvoa voi käyttää sähkölaitetta toiseen

laitteeseen vertaillessa.

Esitetyn värähtelyn päästöarvoa voi käyt-

tää myös alustavaan pysähdyksen arvioin-

tiin.

Varoitus:

Värähtelyn päästöarvo voi sähkö-

käyttöisen työkalun todellisen käy-

tön aikana olla annetusta arvosta

eroavainen, riippuen sähkötyökalun

käytöstä ja käyttötavasta.

Tarpeen on määrätä käyttäjän

turvallisuuteen johtavat suojatoimen-

piteet, jotka kohdistuvat todellisten

käyttöedellytyksien aikana arvioi-

tavaan pysähdykseen (tällöin on

huomioitava kaikki käyttöjakson

osiot, esimerkiksi ajat, jolloin sähkö-

työkalu on pysähtynyt, ja sellaiset,

jolloin se on tosin käynnissä, mutta

kuormituksetta).

Turvallisuusmääräykset

Tämä luku käsittelee periaattellisia turval-

lisuusmääräyksiä, jotka on otettava huo-

mioon sähkökuokkalla työskennellessä.

Symbolit ja kuvat

Laitteessa olevat tekstit:

Lue käyttöohje.

Sähkölaitteet eivät kuulu talousjättei-

siin.

Akussa oleva symboli

Lue käyttöohje.

Sähkölaitteet eivät

kuulu talousjätteisiin

Älä jätä akkua pitemmäksi ajaksi

suoraan auringonvaloon äläkä

myöskään lämpöpatterien päälle.

Kuumuus vahingoittaa akun ja on

olemassa räjähdysvaara (max.

45°C).

Vie käytetyt akut keräyspisteeseen,

josta se viedään ympäristöystävälli-

seen kierrätykseen.

Akku tulee varastoida lada-

tussa tilassa

Akun tarvitsema ympäristön

lämpötila on +10°C - + 40 °C

Akku ei saa joutua kosketuksiin

veden kanssa.

F I

2 0

Sähkötyökaluja koskevat

turvallisuusohjeet

VAROITUS! Lue kaikki turval-

lisuusohjeet ja neuvot.Turval-

lisuusohjeiden noudattamattomuus

voi johtaa sähköiskun saamiseen,

aiheuttaa tulipalon ja/tai vaaralli-

sia vammoja.

Pidä turvallisuusohjeet ja neuvot

hyvin tallessa tulevaisuuden varal-

le.

Turvallisuusohjeissa käytetty termi „ Sähkö-

työkalu“ tarkoittaa sähköisesti toimivia työ-

kaluja (verkkokaapelilla) ja akulla toimivia

työkaluja (ilman verkkokaapelia).

1) TYÖPAIKAN TURVALLISUUS

a) Pidä työpaikka puhtaana ja

huolehdi riittävästä valaistuk-

sesta. Epäpuhtaus ja huono valaistus

työpaikalla voivat johtaa loukkaantu-

misiin.

b) Älä työskentele sähkölaitteella

räjähdysvaarallisella alueella,

jossa on helposti syttyviä nes-

teitä, kaasuja tai pölyä. Sähköllä

käyvät työkalut kehittävät kipinöintiä,

joka voi sytyttää pölyn tai höyryt.

c) Älä anna pienten lasten tai

asiattomien henkilöiden olla

työpaikalla sähkölaitteella

työskennellessä. Häiritseminen

voi aiheuttaa sen, että menetät koneen

hallinnan.

Laturissa olevat symbolit:

Huomio!

Lue käyttöohje.

Laturi on tarkoitettu käytettäväksi

vain sisätiloissa.

T2A

Lasiputkisulake

Suojaluokka II

Sähkölaitteet eivät kuulu talousjättei-

siin.

LED-näyttö latauksen

aikana.

Ohjeessa olevien kuvien selitys:

Vaaraan viittaava merkki

henlilö- ja esinevahinkojen

estämiseksi.

Kieltomerkki (huutomerkin asemasta

kielto on selitetty) vahinkojen estä-

miseksi.

Viite, joka antaa tietoa laitteen käy-

tön helpottamiseksi.

Page is loading ...

Parkside PBSA 12 A1 Original Instruction

Parkside PBSA 12 A1 Original Instruction

in other languages

Related papers

Other documents