Baxton Studio BBT8051.13-Tan/Walnut-5PC Dining Nook Set Assembly Instructions

Brand
Baxton Studio
Model
BBT8051.13-Tan/Walnut-5PC Dining Nook Set
Type
Assembly Instructions

This manual is also suitable for

ASSEMBLY INSTRUCTIONS
MODEL : BBT 8051.13 A3 - SF
HARDWARE LIST
ITEM DESCRIPTION QTY
1 JCBC Bolt M6 x 50mm 4pcs
2 JCBB Bolt M8 x 45mm 8pcs
3 M8 FLAT WASHER 8pcs
4 M6 SPRING WASHER 4pcs
5 M8 SPRING WASHER 8pcs
6 WOOD SCREW M4 x 38mm 10PCS
7 M4 ALLEN KEY (BALL SHAPE) 1PC
8 M5 ALLEN KEY (BALL SHAPE) 1PC
9 WOOD DOWEL M8 x 30mm 8PCS
Read this instruction carefully. See hardware and furniture part list for guidance.
Be sure all parts are complete, before you assemble. Place all wooden furniture
parts on a clean and flat soft surface to prevent from being scratched.
Follow the figure to start assembling.
CAUTIONS : 1. Do not FULLY - TIGHTEN the nut or nut bolt until all nut or bolt is ready assembed.
2. Do not OVER - TIGHTEN the nut or bolt to avoid causing damages to the thread.
3. Keep all hardware parts out of reach of children.
NOTE : THE LIST AND QUANTITY SHOWN ARE FOR 1 UNIT ASSEMBLY.
Tool needed : Screwdriver & Rubber Mallet (not provider).
STEP 1 STEP 2
1 OF 3
417
CE
PART LIST
ITEM DESCRIPTION QTY
A CUSHION BACK 1 PC
B CUSHION SEAT 1 PC
C LEG SUPPORT FRONT 1 PC
D LEG SUPPORT BACK 1 PC
E LEG LEFT 1 PC
F LEG RIGHT 1 PC
G ARM 1 PC
D
FL
R
9
C
D
FRONT
BACK
FRONT
BACK
FRONT
BACK
FRONT
BACK
ASSEMBLY INSTRUCTIONS
STEP 3 STEP 4
2 OF 3
8
2
5
3
A
B
A
B
28
5
3
Don't screw tied **Finish step 4,
Please screw tied the step 3 bolt.
G
G
ASSEMBLY INSTRUCTIONS
STEP 5
3 OF 3
6
STEP 6
L
L
R
R
C
D
E
F
5.1 Follow marking line assemble leg.
ASSEMBLY INSTRUCTIONS
MODEL : BBT 8051.13 A3 - SF
HARDWARE LIST
ITEM DESCRIPTION QTY
1 JCBC Bolt M6 x 50mm 4pcs
2 JCBB Bolt M8 x 45mm 6pcs
3 M8 FLAT WASHER 6pcs
4 M6 SPRING WASHER 4pcs
5 M8 SPRING WASHER 6pcs
6 WOOD SCREW M4 x 38mm 10PCS
7 M4 ALLEN KEY (BALL SHAPE) 1PC
8 M5 ALLEN KEY (BALL SHAPE) 1PC
9 WOOD DOWEL M8 x 30mm 8PCS
Read this instruction carefully. See hardware and furniture part list for guidance.
Be sure all parts are complete, before you assemble. Place all wooden furniture
parts on a clean and flat soft surface to prevent from being scratched.
Follow the figure to start assembling.
CAUTIONS : 1. Do not FULLY - TIGHTEN the nut or nut bolt until all nut or bolt is ready assembed.
2. Do not OVER - TIGHTEN the nut or bolt to avoid causing damages to the thread.
3. Keep all hardware parts out of reach of children.
NOTE : THE LIST AND QUANTITY SHOWN ARE FOR 1 UNIT ASSEMBLY.
Tool needed : Screwdriver & Rubber Mallet (not provider).
PART LIST
ITEM DESCRIPTION QTY
A CUSHION BACK 1 PC
B CUSHION SEAT 1 PC
C LEG SUPPORT FRONT 1 PC
D LEG SUPPORT BACK 1 PC
E LEG LEFT 1 PC
F LEG RIGHT 1 PC
STEP 1 STEP 2
1 OF 3
417
CE
DL
R
F
9
C
D
FRONT
BACK
BACK
FRONT
FRONT
FRONT
BACK
BACK
ASSEMBLY INSTRUCTIONS
STEP 3 STEP 4
2 OF 3
8
2
5
3
A
B
A
B
L
RD
CE
F
L
R
4.1 Follow marking line assemble leg.
6
ASSEMBLY INSTRUCTIONS
STEP 5
3 OF 3
ASSEMBLY INSTRUCTIONS HARDWARE LIST
ITEM DESCRIPTION QTY
1 JCBC Bolt M6 x 50mm 4pcs
2 M6 SPRING WASHER 4pcs
3 WOOD SCREW M4 x 38 8PCS
4 M4 ALLEN KEY (BALL SHAPE) 1PC
5 WOOD DOWEL M8 x 30mm 8PCS
Read this instruction carefully. See hardware and furniture part list for guidance.
Be sure all parts are complete, before you assemble. Place all wooden furniture
parts on a clean and flat soft surface to prevent from being scratched.
Follow the figure to start assembling.
CAUTIONS : 1. Do not FULLY - TIGHTEN the nut or nut bolt until all nut or bolt is ready assembed.
2. Do not OVER - TIGHTEN the nut or bolt to avoid causing damages to the thread.
3. Keep all hardware parts out of reach of children.
NOTE : THE LIST AND QUANTITY SHOWN ARE FOR 1 UNIT ASSEMBLY.
Tool needed : Screwdriver & Hammer (not provider).
PART LIST
ITEM DESCRIPTION QTY
A CUSHION SEAT 1 PC
B LEG SUPPORT 2 PCS
C LEG 2 PCS
STEP 1 STEP 2
1 OF 2
214
5
B
BC
1.1 Open the zip at the bottom of cushion seat and take out all part hardware.
B
ASSEMBLY INSTRUCTIONS
STEP 3 STEP 4
2 OF 2
3
3.1 Follow marking line assemble leg.
ASSEMBLY INSTRUCTIONS
HARDWARE LIST
ITEM DESCRIPTION QTY
1 JCBC Bolt M6 x 50mm 4pcs
2 JCBC Bolt M8 x 45mm 8pcs
3 M8 FLAT WASHER 8pcs
4 M6 SPRING WASHER 4pcs
5 M8 SPRING WASHER 8pcs
6 WOOD SCREW M4 x 38 10PCS
7 M4 ALLEN KEY (BALL SHAPE) 1PC
8 M5 ALLEN KEY (BALL SHAPE) 1PC
9 WOOD DOWEL M8 x 30mm 8PCS
Read this instruction carefully. See hardware and furniture part list for guidance.
Be sure all parts are complete, before you assemble. Place all wooden furniture
parts on a clean and flat soft surface to prevent from being scratched.
Follow the figure to start assembling.
CAUTIONS : 1. Do not FULLY - TIGHTEN the nut or nut bolt until all nut or bolt is ready assembed.
2. Do not OVER - TIGHTEN the nut or bolt to avoid causing damages to the thread.
3. Keep all hardware parts out of reach of children.
NOTE : THE LIST AND QUANTITY SHOWN ARE FOR 1 UNIT ASSEMBLY.
Tool needed : Screwdriver & Hammer (not provider).
STEP 1 STEP 2
1 OF 3
417
CE
PART LIST
ITEM DESCRIPTION QTY
A CUSHION BACK 1 PC
B CUSHION SEAT 1 PC
C LEG SUPPORT FRONT 1 PC
D LEG SUPPORT BACK 1 PC
E LEG LEFT 1 PC
F LEG RIGHT 1 PC
D
FL
R
9
C
D
FRONT
BACK
1.1 Open the zip at the bottom of cushion seat and take out all part hardware.
ASSEMBLY INSTRUCTIONS
MODEL : BBT 8051.13 A3 - CC
HARDWARE LIST
ITEM DESCRIPTION QTY
1 JCBC Bolt M6 x 50mm 4pcs
2 JCBB Bolt M8 x 45mm 4pcs
3 M8 FLAT WASHER 4pcs
4 M6 SPRING WASHER 4pcs
5 M8 SPRING WASHER 4pcs
6 WOOD SCREW M4 x 38mm 6PCS
7 M4 ALLEN KEY (BALL SHAPE) 1PC
8 M5 ALLEN KEY (BALL SHAPE) 1PC
9 WOOD DOWEL M8 x 30mm 8PCS
Read this instruction carefully. See hardware and furniture part list for guidance.
Be sure all parts are complete, before you assemble. Place all wooden furniture
parts on a clean and flat soft surface to prevent from being scratched.
Follow the figure to start assembling.
CAUTIONS : 1. Do not FULLY - TIGHTEN the nut or nut bolt until all nut or bolt is ready assembed.
2. Do not OVER - TIGHTEN the nut or bolt to avoid causing damages to the thread.
3. Keep all hardware parts out of reach of children.
NOTE : THE LIST AND QUANTITY SHOWN ARE FOR 1 UNIT ASSEMBLY.
Tool needed : Screwdriver & Rubber Mallett (not provider).
PART LIST
ITEM DESCRIPTION QTY
A CUSHION BACK 1 PC
B CUSHION SEAT 1 PC
C LEG SUPPORT FRONT 1 PC
D LEG SUPPORT BACK 1 PC
E LEG LEFT 1 PC
F LEG RIGHT 1 PC
STEP 1 STEP 2
1 OF 2
C
CE
417
A
B
A
8
2
5
3
D
D
FL
R
9
1.1 Open the zip at the bottom of
cushion seat and take out all part
hardware.
FRONT
BACK
FRONT
FRONT
BACK
BACK
FRONT
ASSEMBLY INSTRUCTIONS
STEP 3 STEP 4
2 OF 2
6
C
D
E
FL
R
L
R
3.1 Follow marking line assemble leg.
PART LIST
ITEM DESCRIPTION QTY
A TABLE TOP 1 PC
B LEGS 4 PCS
ASSEMBLY INSTRUCTIONS PART LIST
ITEM DESCRIPTION QTY
1 JCBC BOLT M6 x 60mm 8 PCS
2 M6 FLAT WASHER 8 PCS
3 M6 SPRING WASHER 8 PCS
4 M4 ALLEN KEY 1 PC
STEP 1
Read this instruction carefully. See hardware and furniture part list for guidance.
Be sure all parts are complete, before you assemble. Place all wooden furniture
parts on a clean and flat soft surface to prevent from being scratched.
Follow the figure to start assembling.
CAUTIONS : 1. Do not FULLY - TIGHTEN the nut or nut bolt until all nut or bolt is ready assembed.
2. Do not OVER - TIGHTEN the nut or bolt to avoid causing damages to the thread.
3. Keep all hardware parts out of reach of children.
NOTE : THE LIST AND QUANTITY SHOWN ARE FOR 1 UNIT ASSEMBLY.
STEP 2
A
B
2
3
1
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Baxton Studio BBT8051.13-Tan/Walnut-5PC Dining Nook Set Assembly Instructions

Brand
Baxton Studio
Model
BBT8051.13-Tan/Walnut-5PC Dining Nook Set
Type
Assembly Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents