SPECIFICATIONS
HAZARD DEFINITIONS
INTRODUCTION
SAFETY
WARNING! Read and understand all instructions before
using this tool. The operator must follow basic
precautions to reduce the risk of personal injury
and/or damage to the equipment.
WORK AREA
PERSONAL SAFETY
WARNING! Wear personal protective equipment
approved by the Canadian Standards Association (CSA)
or American National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
PERSONAL PRECAUTIONS
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with
product (gained from repeated use) replace strict
adherence to the tool safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious personal
injury.
ELECTRICAL SAFETY
WARNING! Do not touch or handle a live tool with any
part of your body that is wet or damp. Wet skin
reduces resistance to electrical current, increasing
the danger of a serious or fatal shock.
WARNING! To reduce risk of electric shock, be certain
that the plug is connected to a properly grounded
receptacle.
WARNING! All wiring should be performed by a
qualified electrician.
POWER CORD
POLARIZED PLUG
ELECTROMAGNETIC FIELDS
WARNING! Shut off the electrical tool or device and
move away if you feel faint, dizzy, nausea or shocks.
Seek medical attention.
UNPACKING
WARNING! Do not operate the tool if any part is
missing. Replace the missing part before operating.
Failure to do so could result in a malfunction and
personal injury.
ASSEMBLY & INSTALLATION
INSTALLING THE ATTACHMENTS
OPERATION
HIGH SPEED DRILL BIT ATTACHMENT
IDENTIFICATION KEY
SHARPENING DRILL BITS
Caution! Sharpened drill bits may be
hot. Handle with care to prevent minor
burn injuries.
CLAMPING DRILL BITS
Drill bit size
Clamp setup
STANDARD KNIFE AND SCISSOR
ATTACHMENT
IDENTIFICATION KEY
SHARPENING KNIVES
CAUTION! Keep hands away from the
blade. Handle knives and scissors with
care to prevent injuries.
SHARPENING SCISSORS
STRAIGHT-EDGE CHISEL AND PLANE
BLADE ATTACHMENT
IDENTIFICATION KEY
SHARPENING CHISEL AND PLANE BLADES
NOTICE! Do not hold the blade in place against a
running grinding wheel for extended periods as this
may cause irregular sharpening
CARE & MAINTENANCE
WARNING! Only qualified service personnel should
repair the tool. An improperly repaired tool may
present a hazard to the user and/or others.
REMOVING AND INSTALLING THE
GRINDING WHEEL
CLEANING
CAUTION! Do not clean with metal
scouring pads. Metal pieces from
the pad can come in contact with
the electrical parts and increase
the risk of shock.
STORAGE
DISPOSAL
TROUBLESHOOTING
PARTS BREAKDOWN
PARTS LIST
#
DESCRIPTION
QTY
SPÉCIFICATIONS
DÉFINITIONS DE DANGER
INTRODUCTION
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes
les instructions avant d'utiliser cet outil. L'utilisateur
doit respecter les précautions de base lorsqu'il utilise
cet outil afin de réduire le risque de blessure ou de
dommage à l'équipement.
AIRE DE TRAVAIL
SÉCURITÉ PERSONNELLE
AVERTISSEMENT ! Portez de l'équipement de
protection personnelle homologué par l'Association
canadienne de normalisation (CSA) ou l'American
National Standards Institute (ANSI).
ÉQUIPEMENT DE PROTECTION PERSONNELLE
PRÉCAUTIONS PERSONNELLES
CONSIGNES DE SÉCURITÉ SPÉCIFIQUES
AVERTISSEMENT! Ne permettez PAS au confort ou à
votre familiarisation avec l'outil (obtenus après un
emploi répété) de se substituer à une adhésion stricte
aux règles de sécurité de l'outil. Si vous utilisez cet
outil de façon dangereuse ou incorrecte, vous pouvez
subir des blessures corporelles graves.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
