Frigidaire FFWC3822QS User guide

Brand: Frigidaire

Model: FFWC3822QS

Category: Wine coolers

Type: User guide

TABLE OF CONTENTS

www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352

All about the

Use & Care

of your Wine Cooler

Important Safety Instructions .................................2

Installation ...........................................................4

Door Reversal Instructions .....................................5

Energy Saving Tips ................................................6

242101901 (August 2010)

Temperature Controls ............................................7

Features ...............................................................8

Care and Cleaning ................................................ 9

Before you Call ....................................................10

Major Appliance Warranty ....................................12

WARNING

WARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury.

IMPORTANT

IMPORTANT indicates installation, operation or

maintenance information which is important but not

hazard-related.

DANGER

DANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious

injury.

Deﬁnitions

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible injury

or death.

CAUTION

CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury.

WARNING

Please read all instructions before using this Beverage

Cooler.

SERIAL/MODEL #’S - IMPORTANT SAFETY INSTRUCTIONS

Read and Save These Instructions

This Owner’s Guide provides speciﬁc operating

instructions for your model. Use your Wine Cooler only

as instructed in this guide. These instructions are not

meant to cover every possible condition and situation

that may occur. Common sense and caution must be

practiced when installing, operating, and maintaining any

appliance.

Record Your Model and Serial Numbers

Record the model and serial numbers in the space

provided below. The serial plate is located on the upper

left wall inside the Wine Cooler.

Model Number:

Serial Number:

Purchase Date:

IMpORtAnt SAfEty InStRuctIOnS

WARnInG



Destroy carton, plastic bags, and any exterior 

wrapping material immediately after the wine

cooler is unpacked. Children should never use

these items to play. Cartons covered with rugs,

bedspreads, plastic sheets or stretch wrap may

become airtight chambers, and can quickly cause

suffocation.

Remove all staples from the carton. Staples can 

cause severe cuts, and destroy nishes if they

come in contact with other appliances or furniture.

An empty, discarded wine cooler is a very 

dangerous attraction to children.

Remove the door(s) of any appliance that is not in 

use, even if it is being discarded.

WARnInG



• 



 The power cord of

the appliance is equipped with a three-prong

grounding plug for your protection against

electrical shock hazards. It must be plugged

directly into a properly grounded three prong

receptacle. The receptacle must be installed in

accordance with local codes and ordinances.

Consult a qualied electrician. Avoid connecting

refrigerator to a Ground Fault Interruptor (GFI)

circuit. 



If the power cord is damaged, it should be •

replaced by an authorized service technician to

prevent any risk.

Never unplug the wine cooler by pulling on the •

power cord. Always grip the plug rmly, and

pull straight out from the receptacle to prevent

damaging the power cord.

Unplug the wine cooler before cleaning and before •

replacing a light bulb to avoid electrical shock.

Performance may be affected if the voltage varies •

by 10% or more. Operating the wine cooler with

insufcient power can damage the compressor.

Such damage is not covered under your warranty.

Do not plug the unit into an electrical outlet •

controlled by a wall switch or pull cord to prevent

the wine cooler from being turned off accidentally.

WARnInG





Child entrapment and suffocation are not problems of

the past. Junked or abandoned wine coolers are still

dangerous – even if they will sit for “just a few days”.

If you are getting rid of your old wine cooler, please

follow the instructions below to help prevent accidents.

We strongly encourage responsible appliance recycling/

disposal methods. Check with your utility company or

visit www.recyclemyoldfridge.com for more information

on recycling your old wine cooler.



Remove doors.•

Leave shelves in place so children may not easily •

climb inside.

Have refrigerant removed by a qualied service •

technician.



nOtE

The exterior walls of the wine cooler may become quite

warm as the compressor works to transfer heat from

the inside. Temperatures as much as 30° F warmer

than room temperature can be expected. For this

reason it is particularly important in hotter climates to

allow enough space for air circulation around your wine

cooler.

    

The wine cooler must have all bottom corners resting

rmly on solid oor. The oor must be strong enough

to support a fully loaded wine cooler. NOTE: It is Very

Important for your wine cooler to be level in order to

function properly. If the wine cooler is not leveled during

installation, the door may be misaligned and not close

or seal properly, causing cooling, frost, or moisture

problems.



After removing all interior and exterior packaging

materials, use a carpenter’s level to level the wine cooler

from front-to-back. Adjust the leveling legs in front, ½

bubble higher, so that the door closes easily when left

halfway open.



Wash any removable parts of the wine cooler interior, 

and exterior with mild detergent and warm water.

Wipe dry. Do not use harsh cleaners on these

surfaces.

Do not use razor blades or other sharp instruments, 

which can scratch the appliance surface when

removing adhesive labels. Any glue left from the tape

can be removed with a mixture of warm water and

mild detergent, or touch the residue with the sticky

side of tape already removed. Do not remove the

serial plate.

 Do not store food in your wine

cooler as interior temperature may not get cool enough

to prevent spoilage. In summer months or areas of high

humidity, the glass door may build up moisture. To

remove the moisture, wipe it away.



Set handle over the two mounting studs at top of 

door.

Use hex head screw driver or allen wrench to tighten 

set screws from bottom to secure handle to door.

� Handle

ĸ Wooden Shelf Made of Beech

Ĺ Control Panel

� Glass Door

� Control Switch of Lamp

� Adjustable Leg

Placement of Wine Cooler

The wine cooler should be placed in dry and ventilated room. The location of

the wine cooler should not be irradiated by direct sunshine. The wine cooler

should be far away from heating sources, such as: cooking stove or heating

radiator. If the wine cooler has to be placed near heating source, please adopt

proper heating insulation board for insulation or keep the wine cooler at least

the following minimum distances away from the heating sources:

For electric stove: 3 ΁.

For oil or coal stove: 30 ΁.

Replacement of Door Hinge

The door hinges of this wine cooler can be interchanged between the left and

right sides.

Installation of Handle

1. Set the handle on the fixation shaft.

Fixation Shaft of Handle

Set Handle

2. Screw down the fixation pins of the handle with screw driver.

- 7 -

Mounting stud

Locate handle

Screw driver

Handle Fixation Pin

Screw Driver

Level the Wine Cooler

Place the wine cooler on the planned location and level it.

The front screw of leg is adjustable.

Pay Attention to Room Temperature & Ventilation

The climate type is marked on the model nameplate. It indicates the room

temperature range for operation of wine cooler.

Climate Type Indoor Temperature Range

N +16°C to 32°C

ST +18°C to 38°C

T +18°C to 43°C

- 8 -

Set screw

InStALLAtIOn

This Use & Care Guide provides general operating

instructions for your model. Use the appliance only as

instructed in this Use & Care Guide. 





Choose a place that is near a grounded electrical •

outlet.  use an extension cord or an adapter

plug.

For optimal performance, it is recommended that •

you install the wine cooler where the ambient

temperature is between 70 and 78 degrees

fahrenheit.

Allow space around the unit for good air circulation. •

Leave a 2 inch space on the back and sides of the

wine cooler for adequate circulation.

Be sure the wine cooler stays in the upright position •

during transport.

Keep the wine cooler from any hazardous or •

combustible agents.



The glass door can be opened from left to right and vice

versa. Should you desire to change the opening direction,

please follow these instructions.



nOtE

All parts removed must be saved to do the

reinstallation of the door.

Remove top cap. Remove the three screws that hold 

the upper hinge (right side) to the top of the cabinet.

See Fig. 1.

Carefully remove top hinge (See Fig. 1.), then lift the 

door up off of bottom hinge and place it on a padded

surface to prevent scratching it. See Fig. 2.

Remove the three button plugs from the upper left 

corner of the cabinet and transfer them to the holes

on the opposite side. Be sure to press the button

plugs rmly into the holes. See Fig. 1.

Remove three screws that hold the bottom hinge to 

lower end of cabinet. Remove the three button plugs

from lower LH corner and transfer to holes where

bottom hinge was just removed. See Fig. 3.

Unscrew pins from both hinges and transfer to 

threaded hole on opposite side. See Fig. 4. Re-install

bottom hinge in LH corner of cabinet using same

three screws removed in Step 4.

On bottom edge of door, transfer door stop bracket 

and bushing to holes on opposite side. See Fig. 6.

On top edge of door, transfer the button plugs and 

bushing to hole on opposite side. See Fig. 7.

Place bottom LH corner of door onto lower hinge, 

then install top hinge to cabinet. Make sure door

is level and it seals properly against cabinet, then

securely fasten three screws. See Fig. 7. Snap top

cap back onto hinge.

Chart 2

Step 7:Remove the bolt on the bottom of the door by screwdriver�(see chart

Step 8:Remove the screw� and the block �,then set them on the left side.(see

chart 3)

Chart 3

Step 9:Change the hinge axis� from the right hole to left hole(see chart 4)

Chart 4

Step 10:Use knife to remove the parts�,see chart 5.

- 8 -



Screws

Top cap

Bushing

Hinge

� Handle

ĸ Wooden Shelf Made of Beech

Ĺ Control Panel

� Glass Door

� Control Switch of Lamp

� Adjustment Leg

Door Reversal Instructions:

You can reverse the door swing if you change the position of the hinge(�) ,pls

follow the steps below:

Step 1:Close the door and use the knife carefully to remove the parts�ǃ�(see

chart 1)

Step 2:Remove the hinge coverĹ(see chart 1)

Step 3:Remove the screws by cross-screwdriverĺ(see chart 1)

Step 4:Remove the top hingeĻ(see chart 1)

Step 5:Remove the bolt by screwdriverļ(see chart 1)

Chart 1

Step 6:Open the door and lift it up carefully then remove it,see chart 2.

- 7 -

Button plugs

Step 11:Loosen the bolt� and bottom hinge�ˈthen replace the parts on the

left and right sideˈthen assemble the parts,see chart 6.

Chart 5

Chart 6

Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see

chart 7.

Chart 7

Step 13:Assemble the door on the bottom hinge�ˈthen reset the door bolt�

- 9 -



Move pin to

opposite hole

(upper and

lower hinges)

Step 11:Loosen the bolt� and bottom hinge�ˈthen replace the parts on the

left and right sideˈthen assemble the parts,see chart 6.

Chart 5

Chart 6

Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see

chart 7.

Chart 7

Step 13:Assemble the door on the bottom hinge�ˈthen reset the door bolt�

- 9 -



Button plugs

Screws

Hinge

Step 11:Loosen the bolt� and bottom hinge�ˈthen replace the parts on the

left and right sideˈthen assemble the parts,see chart 6.

Chart 5

Chart 6

Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see

chart 7.

Chart 7

Step 13:Assemble the door on the bottom hinge�ˈthen reset the door bolt�

- 9 -



Button plugs

Screws



InStALLAtIOn

and fix the top hinge on the door,to make the door level,see chart 8.

Step 14:Check the sealing of the door,then refit the parts �ǃ�.

Chart 8

Placement of Wine Cooler

The wine cooler should be placed in dry and ventilated room. The location of

the wine cooler should not be irradiated by direct sunshine. The wine cooler

should be far away from heating sources, such as: cooking stove or heating

radiator. If the wine cooler has to be placed near heating source, please adopt

proper heating insulation board for insulation or keep the wine cooler at least

the following minimum distances away from the heating sources:

For electric stove: 3 ΁.

For oil or coal stove: 30 ΁.

Replacement of Door Hinge

The door hinges of this wine cooler can be interchanged between the left and

right sides.

Installation of Handle

1. Set the handle on the fixation shaft.

- 10 -



Chart 2

Step 7:Remove the bolt on the bottom of the door by screwdriver�(see chart

Step 8:Remove the screw� and the block �,then set them on the left side.(see

chart 3)

Chart 3

Step 9:Change the hinge axis� from the right hole to left hole(see chart 4)

Chart 4

Step 10:Use knife to remove the parts�,see chart 5.

- 8 -



Bushing

Stop

bracket

Install the wine cooler in the 

coolest part of a dry and ventilated

room, out of direct sunlight and

away from heating ducts or

registers. Do not place the wine

cooler next to heat-producing

appliances such as a range, oven

or dishwasher.

Level the wine cooler so the door close tightly.

Do not over crowd the wine cooler or block cold air 

vents. Doing so causes the wine cooler to run longer

and use more energy. Shelves should not be lined

with aluminum foil, wax paper or paper toweling.

Liners interfere with cold air circulation, making the

wine cooler less efcient.

Wipe containers dry before placing them in the wine 

cooler. This cuts down on moisture build-up inside

the unit.

Organize the wine cooler to reduce door openings. 

Remove as many items as needed at one time and

close the door as soon as possible.



InStALLAtIOn



For best performance, allow 4 hours for the wine cooler to cool down completely. The wine cooler will run continuously

for the rst several hours.



Indication of Temperature in Lower Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

Indication of Temperature in Upper Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

: Temperature display.

Light: Lighting button for LED lamp; it controls the on/off of lamp.

Power: On/off button used to turn on/off all load.

Press Light and Power together for 2 seconds and you can convert between

fahrenheit temperature and Celsius temperature.

Notice!

z The default temperature is 10/10°C, and the temperature after power

failure will be the temperature set before the power failure.

z To elongate the service life of compressor, please wait for at least 5

minutes before the wine cooler is restarted after power failure.

z Failure display

z If there is failure on the sensor, the screen may display failure code, such

as: E and F. When the screen displays the above-mentioned errors, please

do not disassemble it for check by yourself. You should contact local

after-sales service personnel for repair.

z If the temperature in the cooler is too low, it will display “L”.

When the temperature in the cooler is too high, the screen will display “H”

and will flash; under this state, the buzzer will buzz until 30 seconds; one

minute later, the buzzer will continue to give alarm in the next 30 seconds; after

the alarm is given for three times, it will not give alarm any more. You can

press any key to cancel sound alarm.

z When you put a lot of wines together in the cooler, the temperature in the

cooler may rise temporarily.

- 10 -



 This button turns the light ON and OFF.

 This buttons turns the power ON and OFF.

Press both  and  button’s at the same time

to change between Fahrenheit and Celsius temperatures.

Indication of Temperature in Lower Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

Indication of Temperature in Upper Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

: Temperature display.

Light: Lighting button for LED lamp; it controls the on/off of lamp.

Power: On/off button used to turn on/off all load.

Press Light and Power together for 2 seconds and you can convert between

fahrenheit temperature and Celsius temperature.

Notice!

z The default temperature is 10/10°C, and the temperature after power

failure will be the temperature set before the power failure.

z To elongate the service life of compressor, please wait for at least 5

minutes before the wine cooler is restarted after power failure.

z Failure display

z If there is failure on the sensor, the screen may display failure code, such

as: E and F. When the screen displays the above-mentioned errors, please

do not disassemble it for check by yourself. You should contact local

after-sales service personnel for repair.

z If the temperature in the cooler is too low, it will display “L”.

When the temperature in the cooler is too high, the screen will display “H”

and will flash; under this state, the buzzer will buzz until 30 seconds; one

minute later, the buzzer will continue to give alarm in the next 30 seconds; after

the alarm is given for three times, it will not give alarm any more. You can

press any key to cancel sound alarm.

z When you put a lot of wines together in the cooler, the temperature in the

cooler may rise temporarily.

- 10 -

Press this button once to increase temperature 1° F/C.

Press this button once to decrease temperature 1° F/C.

The wine cooler can be operated by adjusting the temperature control buttons (up arrow and down arrow) until

the desired temperature is reached.

The display will ash for a few seconds before set point is locked in.

The temperature range MIN and MAX is 41° - 64°F (5° - 18° C).

tEMpERAtuRE cOntROLS

The default temperature for the wine cooler is 54°F (12°C). The temperature after power failure will be the 

temperature set before the power failure.

To prolong the life of compressor, please wait for at least 5 minutes before the wine cooler is restarted after power 

failure.



If “E” and “F” are displayed, please contact local service personnel for repair.

If the temperature in the cooler is too low, it will display “L”.

If the temperature in the cooler is too high, the screen will display “H” and will ash. Under this state, the buzzer 

will buzz for 30 seconds. One minute later, the buzzer will continue to buzz for the next 30 seconds. After three

times, the alarm will not buzz any more. You can press any key to cancel sound alarm.

Storing too many wine bottles in the cooler may cause the temperature in the cooler to rise temporarily.





Press this button once to increase temperature 1° F/C.

Press this button once to decrease temperature 1° F/C.



Press this button once to increase temperature 1° F/C.

Press this button once to decrease temperature 1° F/C.

Indication of Temperature in Lower Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

Indication of Temperature in Upper Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

: Temperature display.

Light: Lighting button for LED lamp; it controls the on/off of lamp.

Power: On/off button used to turn on/off all load.

Press Light and Power together for 2 seconds and you can convert between

fahrenheit temperature and Celsius temperature.

Notice!

z The default temperature is 10/10°C, and the temperature after power

failure will be the temperature set before the power failure.

z To elongate the service life of compressor, please wait for at least 5

minutes before the wine cooler is restarted after power failure.

z Failure display

z If there is failure on the sensor, the screen may display failure code, such

as: E and F. When the screen displays the above-mentioned errors, please

do not disassemble it for check by yourself. You should contact local

after-sales service personnel for repair.

z If the temperature in the cooler is too low, it will display “L”.

When the temperature in the cooler is too high, the screen will display “H”

and will flash; under this state, the buzzer will buzz until 30 seconds; one

minute later, the buzzer will continue to give alarm in the next 30 seconds; after

the alarm is given for three times, it will not give alarm any more. You can

press any key to cancel sound alarm.

z When you put a lot of wines together in the cooler, the temperature in the

cooler may rise temporarily.

- 10 -

Indication of Temperature in Lower Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

Indication of Temperature in Upper Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

: Temperature display.

Light: Lighting button for LED lamp; it controls the on/off of lamp.

Power: On/off button used to turn on/off all load.

Press Light and Power together for 2 seconds and you can convert between

fahrenheit temperature and Celsius temperature.

Notice!

z The default temperature is 10/10°C, and the temperature after power

failure will be the temperature set before the power failure.

z To elongate the service life of compressor, please wait for at least 5

minutes before the wine cooler is restarted after power failure.

z Failure display

z If there is failure on the sensor, the screen may display failure code, such

as: E and F. When the screen displays the above-mentioned errors, please

do not disassemble it for check by yourself. You should contact local

after-sales service personnel for repair.

z If the temperature in the cooler is too low, it will display “L”.

When the temperature in the cooler is too high, the screen will display “H”

and will flash; under this state, the buzzer will buzz until 30 seconds; one

minute later, the buzzer will continue to give alarm in the next 30 seconds; after

the alarm is given for three times, it will not give alarm any more. You can

press any key to cancel sound alarm.

z When you put a lot of wines together in the cooler, the temperature in the

cooler may rise temporarily.

- 10 -



 This LED turns the light ON and OFF.

 This LED turns the power ON and OFF.

Press both  and  LED’s at the same time to

change between fahrenheit and Celsius temperatures.

The default temperature is 46°F (8°C) for upper zone and 59°F (15°C) for lower zone. The temperature after 

power failure will be the temperature set before the power failure.

To prolong the life of compressor, please wait for at least 5 minutes before the wine cooler is restarted after power 

failure.



If “E” and “F” are displayed, please contact local service personnel for repair.

If the temperature in the cooler is too low, it will display “L”.

If the temperature in the cooler is too high, the screen will display “H” and will ash. Under this state, the buzzer 

will buzz for 30 seconds. One minute later, the buzzer will continue to buzz for the next 30 seconds. After three

times, the alarm will not buzz any more. You can press any key to cancel sound alarm.

Storing too many wine bottles in the cooler may cause the temperature in the cooler to rise temporarily.

The temperature range MIN and MAX is 41 - 54° F for the upper zone and 54 - 64° F for the lower zone.

The wine cooler can be operated by adjusting the temperature control buttons (up arrow and down arrow) until

the desired temperature is reached.

The display will ash for a few seconds before set point is locked in.

Indication of Temperature in Lower Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

Indication of Temperature in Upper Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

: Temperature display.

Light: Lighting button for LED lamp; it controls the on/off of lamp.

Power: On/off button used to turn on/off all load.

Press Light and Power together for 2 seconds and you can convert between

fahrenheit temperature and Celsius temperature.

Notice!

z The default temperature is 10/10°C, and the temperature after power

failure will be the temperature set before the power failure.

z To elongate the service life of compressor, please wait for at least 5

minutes before the wine cooler is restarted after power failure.

z Failure display

z If there is failure on the sensor, the screen may display failure code, such

as: E and F. When the screen displays the above-mentioned errors, please

do not disassemble it for check by yourself. You should contact local

after-sales service personnel for repair.

z If the temperature in the cooler is too low, it will display “L”.

When the temperature in the cooler is too high, the screen will display “H”

and will flash; under this state, the buzzer will buzz until 30 seconds; one

minute later, the buzzer will continue to give alarm in the next 30 seconds; after

the alarm is given for three times, it will not give alarm any more. You can

press any key to cancel sound alarm.

z When you put a lot of wines together in the cooler, the temperature in the

cooler may rise temporarily.

- 10 -









fEAtuRES

appliances.

GB-T 23777-2009 Wine Cooler

International or other national or regional standards:

UL 250 BULLETINS-2003 U.S.A. household fridge safety requirements

IEC 61000-3-4-1998 Electromagnetic compatibility (EMC) - Limits -

Limitation of emission of harmonic currents in low-voltage power supply

systems for equipment with rated current greater than 16 A

UL 250 BULLETINS2-2003 U.S.A. household fridge safety

requirements

Enterprise Standard

Q/MB 004-2007 Wine Cooler

Know About Wine Cooler



Fig. 1

The illustration might be different from the actual products.

- 6 -



Multi-position adjustable interior shelves can be moved to any position for larger or smaller packages. The shipping

spacers that stabilize the shelves for shipping should be removed and discarded.



The light comes on automatically when the door is opened. The light can also be turned on and off by pressing the

 button on the control panel. Press the button twice to keep the light on when the door is closed.



This unit is equipped with a lock near the bottom of the door. Two keys are provided. Keep the keys out of reach of

children.

Wine Cooler - Dual Zone

1 Handle

2 Wooden shelf

3 Control panel

4 Glass door

5 Light switch

6 Adjustable leg



1 Handle

2 Control panel

3 Wire shelves

4 Glass door

5 Light switch

6 Adjustable legs

CARE AND CLEANING

Wine Cooler

1 Handle

2 Control panel

3 Wire racks

4 Glass door

5 Light switch

6 Adjustable legs

Cleaning the wine cooler

Before cleaning, turn the temperature control to OFF, •

unplug the wine cooler and remove the bottles.

Clean your wine cooler once every two months.•

Inside: Wash inside surfaces of the wine cooler with a

solution of two tablespoons of baking soda in one quart

(1.136 litres) warm water. Rinse and dry. Wring excess

water out of the sponge or cloth when cleaning in the

area of the controls, or any electrical parts.

Wash the removable parts with the baking soda solution

mentioned above, or mild detergent and warm water.

Rinse and dry. Never use metallic scouring pads,

brushes, abrasive cleaners, or alkaline solutions on any

surface. Do not wash removable parts in a dishwasher.

Outside: Wash the cabinet with warm water and mild

liquid detergent. Rinse well and wipe dry with a clean

soft cloth.

Care of plastic parts

Be sure and protect the door gasket. It should be •

kept clean at all times.

If the plastic parts in the wine cooler remain •

contaminated by oil (animal or vegetable) for a long

period of time, they will age and crack easily. Please

clean them on a regular basis.

Vacation and Moving Tips

Vacations:

If the wine cooler will not be used for several months:

Remove all wine bottles and unplug the power cord. •

Clean and dry the interior thoroughly. •

Leave the wine cooler door open slightly, blocking it •

open if necessary, to prevent odor and mold growth.

Moving: When moving the wine cooler, follow these

guidelines to prevent damage:

Disconnect the power cord plug from the wall outlet.•

Remove wine bottles and clean the wine cooler.•

Secure all loose items by taping them securely in •

place to prevent damage.

In a moving vehicle, secure the wine cooler in an •

upright position to prevent movement. Also, protect

the outside of the wine cooler with a blanket or

similar item.

WARNING

If leaving the wine cooler door open while on vacation,

make certain that children cannot get into the wine

cooler and become entrapped.

appliances.

Wine Cooler

national or regional standards:

LLETINS-2003 U.S.A. household fridge safety requirements

Electromagnetic compatibility (EMC) - Limits -

emission of harmonic currents in low-voltage power supply

ater than 16 A

U.S.A. household fridge safety

Know About Wine Cooler

GB-T 23777-2009

International or other

UL 250 BU

IEC 61000-3-4-1998

Limitation of

systems for equipment with rated current gre

UL 250 BULLETINS2-2003

requirements

Enterprise Standard

Q/MB 004-2007 Wine Cooler

Fig. 1

The illustration might be different from the actual products.

- 7 -

Beverage Center

1 Handle

2 Control panel

3 Glass shelves

4 Glass door

5 Light switch

6 Adjustable legs



Before cleaning, turn the temperature control to OFF, 

unplug the wine cooler and remove the bottles.

Clean your wine cooler once every two months.

Wash inside surfaces of the wine cooler with a

solution of two tablespoons of baking soda in one quart

(1.136 liters) warm water. Rinse and dry. Wring excess

water out of the sponge or cloth when cleaning in the

area of the controls, or any electrical parts.

Wash the removable parts with the baking soda solution

mentioned above, or mild detergent and warm water.

Rinse and dry. Never use metallic scouring pads,

brushes, abrasive cleaners, or alkaline solutions on any

surface. Do not wash removable parts in a dishwasher.

 Wash the cabinet with warm water and mild

liquid detergent. Rinse well and wipe dry with a clean

soft cloth.



Be sure and protect the door gasket. It should be 

kept clean at all times.

If the plastic parts in the wine cooler remain 

contaminated by oil (animal or vegetable) for a long

period of time, they will age and crack easily. Please

clean them on a regular basis.





If the wine cooler will not be used for several months:

Remove all wine bottles and unplug the power cord. 

Clean and dry the interior thoroughly. 

Leave the wine cooler door open slightly, blocking it 

open if necessary, to prevent odor and mold growth.

Moving: When moving the wine cooler, follow these

guidelines to prevent damage:

Disconnect the power cord plug from the wall outlet.

Remove wine bottles and clean the wine cooler.

Secure all loose items by taping them securely in 

place to prevent damage.

In a moving vehicle, secure the wine cooler in an 

upright position to prevent movement. Also, protect

the outside of the wine cooler with a blanket or

similar item.

WARnInG

If leaving the wine cooler door open while on vacation,

make certain that children cannot climb inside and

become entrapped.

cARE AnD cLEAnInG

pROBLEM cAuSE cORREctIOn

WInE cOOLER OpERAtIOn





Wine cooler is plugged into a •

circuit that has a ground fault

interrupt.

Temperature control is in the •

OFF position.

Wine cooler may not be •

plugged in, or plug may be

loose.

House fuse blown or tripped •

circuit breaker.

Power outage.•

Use another circuit. If you are unsure about the outlet, •

have it checked by a certied technician.

See •  section.

Ensure plug is tightly pushed into outlet.•

Check/replace fuse with a 15 amp time-delay fuse. Reset •

circuit breaker.

Check house lights. Call local Electric Company.•





Room or outside weather is •

hot.

Wine Cooler has recently been •

disconnected for a period of

time.

Large amounts of warm or hot •

food has been stored recently.

Door is opened too frequently •

or too long.

Wine Cooler door may be •

slightly open.

Temperature control is set too •

low.

Wine Cooler gasket is dirty, •

worn, cracked, or poorly tted.

It’s normal for the Wine Cooler to work harder under these •

conditions.

It takes 4 hours for the Wine Cooler to cool down •

completely.

Warm food will cause Wine Cooler to run more until the •

desired temperature is reached.

Warm air entering the Wine Cooler causes it to run more. •

Open doors less often.

See • “DOOR pROBLEMS” section.

Turn control knob to a warmer setting. Allow several hours •

for the temperature to stabilize.

Clean or change gasket. Leaks in the door seal will cause •

Wine Cooler to run longer in order to maintain desired

temperature.







Temperature control is set too •

low.

Turn the control to a warmer setting. Allow several hours •

for the temperature to stabilize.







Temperature control is set too •

warm.

Door is opened too frequently •

or too long.

Door may not be seating •

properly.

Large amounts of warm or hot •

food has been stored recently.

Wine Cooler has recently been •

disconnected for a period of

time.

Turn control to a colder setting. Allow several hours for the •

temperature to stabilize.

Warm air entering the Wine Cooler causes it to run more. •

Open doors less often.

See • “DOOR pROBLEMS” section.

Warm food will cause Wine Cooler to run more until the •

desired temperature is reached.

It takes 4 hours for the Wine Cooler to cool down •

completely.







The external Wine Cooler walls •

can be as much as 30°F warm-

er than room temperature.

This is normal while the compressor works to transfer heat •

from inside the Wine Cooler cabinet.

SOunD AnD nOISE







Modern wine coolers have •

increased storage capacity and

more stable temperatures.

They require a high efciency

compressor

This is normal. When the surrounding noise level is low, •

you might hear the compressor running while it cools the

interior

BEfORE yOu cALL

Visit our web site at

www.frigidaire.com.

1-800-944-9044 (United States)

1-800-265-8352 (Canada)



pROBLEM cAuSE cORREctIOn









Wine Cooler operates at higher •

pressures during the start of the

ON cycle.

This is normal. Sound will level off or disappear as refrig-•

erator continues to run.







Exterior thermostat has acti-•

vated the heater or fan.

This is normal.•



-



Metal parts undergo expansion •

and contraction, as in hot water

pipes.

This is normal. Sound will level off or disappear as Wine •

Cooler continues to run.



-



Refrigerant (used to cool Wine •

Cooler) is circulating through-

out the system.

This is normal.•





Wine Cooler is not level. It •

rocks on the oor when it is

moved slightly.

Level the unit. Refer to leveling instructions in the •

section.

 Cold control turning the Wine •

Cooler OFF and ON.

This is normal.•

WAtER/MOIStuRE/fROSt InSIDE WInE cOOLER







Weather is hot and humid.•

Door may not be seating •

properly.

Door is kept open too long, or •

opened too frequently.

This is normal.•

See • “DOOR pROBLEMS” section.

Open the door less often.•

WAtER/MOIStuRE/fROSt OutSIDE WInE cOOLER

-



Door may not be seating prop-•

erly, causing the cold air from

inside the wine cooler to meet

warm moist air from outside.

See • “DOOR pROBLEMS” section.

ODOR In WInE cOOLER

 Interior needs to be cleaned.• Clean interior with sponge, warm water, and baking soda.•

DOOR pROBLEMS

 Wine Cooler is not level. It •

rocks on the oor when it is

moved slightly.

This condition may force the cabinet out of square and •

misalign the door. Refer to “Leveling’ in the 

section.



 Light bulb is burnt out.•

No electric current is reaching •

the Wine Cooler.

Follow instructions under “Interior Light” in the •

“fEAtuRES” section.

See •  section.

MAjOR AppLIAncE WARRAnty

Your appliance is covered by a one year limited warranty. For one year from your original date of

purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove

to be defective in materials or workmanship when such appliance is installed, used and maintained in

accordance with the provided instructions.



1. Products with original serial numbers that have been removed, altered or cannot be readily determined.

2. Product that has been transferred from its original owner to another party or removed outside the USA or

Canada.

3. Rust on the interior or exterior of the unit.

4. Products purchased “as-is” are not covered by this warranty.

5. Food loss due to any refrigerator or freezer failures.

6. Products used in a commercial setting.

7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances

not in ordinary household use or used other than in accordance with the provided instructions.

8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.

9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,

etc.,which are not a part of the appliance when it is shipped from the factory.

10. Service calls to repair or replace appliance light bulbs, air  lters, water  lters, other consumables, or

knobs, handles, or other cosmetic parts.

11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip

charges, or mileage expense for service calls to remote areas, including the state of Alaska.

12. Damages to the  nish of appliance or home incurred during installation, including but not limited to  oors,

cabinets, walls, etc.

13. Damages caused by: services performed by unauthorized service companies; use of parts other than

genuine Electrolux parts or parts obtained from persons other than authorized service companies; or

external causes such as abuse, misuse, inadequate power supply, accidents,  res, or acts of God.

DIScLAIMER Of IMpLIED WARRAntIES; LIMItAtIOn Of REMEDIES

CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT

REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR

OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT

BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL

EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED

WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL

OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE

LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.

Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period

should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.

Service under this warranty must be obtained by contacting Electrolux at the addresses or phone

numbers below.







This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances

North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.

Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under

this warranty must be performed by Electrolux or an authorized service company. Product features or speci cations as described

or illustrated are subject to change without notice.

uSA



Electrolux Major Appliances

North America

10200 David Taylor Drive

Charlotte, NC 28262





Electrolux Canada Corp.

5855 Terry Fox Way

Mississauga, Ontario, Canada

L5V 3E4



uSA



Electrolux Major Appliances

North America

10200 David Taylor Drive

Charlotte, NC 28262





Electrolux Canada Corp.

5855 Terry Fox Way

Mississauga, Ontario, Canada

L5V 3E4

Page is loading ...

INsTALACIÓN

Step 11:Loosen the bolt� and bottom hinge�ˈthen replace the parts on the

left and right sideˈthen assemble the parts,see chart 6.

Chart 5

Chart 6

Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see

chart 7.

Chart 7

Step 13:Assemble the door on the bottom hinge�ˈthen reset the door bolt�

- 9 -

Step 11:Loosen the bolt� and bottom hinge�ˈthen replace the parts on the

left and right sideˈthen assemble the parts,see chart 6.

Chart 5

Chart 6

Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see

chart 7.

Chart 7

Step 13:Assemble the door on the bottom hinge�ˈthen reset the door bolt�

- 9 -



La puerta de vidrio se puede abrir de izquierda a derecha y

viceversa. Si desea cambiar la dirección de apertura, siga estas

instrucciones.



NOTA

Todas las piezas extraídas se deben guardar para realizar la

reinstalación de la puerta.

Quite la tapa superior. Quite los tres tornillos que soportan 

la bisagra superior (costado derecho) con la parte superior

del gabinete. Vea la Figura 1.

Quite cuidadosamente la bisagra superior (vea la Figura 

1), luego eleve la puerta y aleje de la bisagra inferior,

colóquela en una supercie acolchada para evitar arañarla.

Vea la Figura 2.

Quite los tres tapones cabeza de botón de la esquina 

izquierda del gabinete y transéralos a los oricios del lado

opuesto. Asegúrese de presionar los tapones cabeza de

botón rmemente en los oricios. Vea la Figura 1.

Quite los tres tornillos que soportan la bisagra inferior en el 

extremo inferior del gabinete. Quite los tres tapones cabeza

de botón de la esquina izquierda inferior y transéralos

a los oricios donde la bisagra inferior fue quitada

recientemente. Vea la Figura 3.

Desenrosque las clavijas de ambas bisagras y transéralas 

al oricio roscado del lado opuesto. Vea la Figura 4. Vuelva

a instalar la bisagra inferior en la esquina izquierda del

gabinete utilizando los tres tornillos quitados en el paso 4.

En el borde inferior de la puerta, transera la boquilla y el 

soporte de detención de la puerta a los oricios del lado

opuesto. Vea la Figura 6.

En el borde superior de la puerta, transera la boquilla y los 

tapones cabeza de botón a los oricios del lado opuesto.

Vea la Figura 7.



Desplace la

clavija al

oricio opuesto

(bisagras

superiores e

inferiores)



Tapones cabeza

de botón

Tornillos

Bisagra



Tapones cabeza de botón

Tornillos

� Handle

ĸ Wooden Shelf Made of Beech

Ĺ Control Panel

� Glass Door

� Control Switch of Lamp

� Adjustment Leg

Door Reversal Instructions:

You can reverse the door swing if you change the position of the hinge(�) ,pls

follow the steps below:

Step 1:Close the door and use the knife carefully to remove the parts�ǃ�(see

chart 1)

Step 2:Remove the hinge coverĹ(see chart 1)

Step 3:Remove the screws by cross-screwdriverĺ(see chart 1)

Step 4:Remove the top hingeĻ(see chart 1)

Step 5:Remove the bolt by screwdriverļ(see chart 1)

Chart 1

Step 6:Open the door and lift it up carefully then remove it,see chart 2.

- 7 -

Tornillos

Tapa

superior

Buje

Bisagra

Tapones cabeza de botón



Coloque la esquina izquierda inferior de la puerta en la 

bisagra inferior, luego instale la bisagra superior en el

gabinete. Asegúrese de que la puerta esté nivelada y cierre

correctamente contra el gabinete, luego ajuste bien los tres

tornillos. Vea la Figura 7. Recupere la tapa superior en la

bisagra.

Chart 2

Step 7:Remove the bolt on the bottom of the door by screwdriver�(see chart

Step 8:Remove the screw� and the block �,then set them on the left side.(see

chart 3)

Chart 3

Step 9:Change the hinge axis� from the right hole to left hole(see chart 4)

Chart 4

Step 10:Use knife to remove the parts�,see chart 5.

- 8 -



Step 11:Loosen the bolt� and bottom hinge�ˈthen replace the parts on the

left and right sideˈthen assemble the parts,see chart 6.

Chart 5

Chart 6

Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see

chart 7.

Chart 7

Step 13:Assemble the door on the bottom hinge�ˈthen reset the door bolt�

- 9 -

and fix the top hinge on the door,to make the door level,see chart 8.

Step 14:Check the sealing of the door,then refit the parts �ǃ�.

Chart 8

Placement of Wine Cooler

The wine cooler should be placed in dry and ventilated room. The location of

the wine cooler should not be irradiated by direct sunshine. The wine cooler

should be far away from heating sources, such as: cooking stove or heating

radiator. If the wine cooler has to be placed near heating source, please adopt

proper heating insulation board for insulation or keep the wine cooler at least

the following minimum distances away from the heating sources:

For electric stove: 3 ΁.

For oil or coal stove: 30 ΁.

Replacement of Door Hinge

The door hinges of this wine cooler can be interchanged between the left and

right sides.

Installation of Handle

1. Set the handle on the fixation shaft.

- 10 -

Chart 2

Step 7:Remove the bolt on the bottom of the door by screwdriver�(see chart

Step 8:Remove the screw� and the block �,then set them on the left side.(see

chart 3)

Chart 3

Step 9:Change the hinge axis� from the right hole to left hole(see chart 4)

Chart 4

Step 10:Use knife to remove the parts�,see chart 5.

- 8 -





Boquilla

Soporte

detención

Instale el enfriador de bebidas en la parte 

más fría de una habitación ventilada y

seca, lejos de la exposición directa de

la luz solar y lejos de los conductos de

calefacción o registros. No coloque el

enfriador de bebidas y vinos cerca de

electrodomésticos que produzcan calor

como una cocina, horno o lavavajillas.

Nivele el enfriador de bebidas de manera que la puerta se 

cierre bien.

No llene en exceso el enfriador de bebidas o bloquee 

las ventilaciones de aire frío. Si lo hace, provocará que

el enfriador de bebidas funcione más y utilice más

energía. Los estantes no deben estar cubiertos con

láminas de aluminio, papel de cera o toalla de papel. Los

revestimientos intereren con la circulación de aire frío, lo

que hace que el enfriador de bebidas y vinos sea menos

eciente.

Limpie en seco los envases antes de colocarlos en el 

enfriador de bebidas. Esto disminuye la acumulación de

humedad dentro de la unidad.

Organice el enfriador de bebidas para reducir las aperturas 

de la puerta. Retire tantos artículos como sea necesario

una sola vez y cierre la puerta lo antes posible.



INsTALACIÓN



Para un mejor funcionamiento, deje pasar 4 horas para que el enfriador de bebidas se enfríe completamente. El enfriador de bebidas

funcionará continuamente durante las primeras horas.



Indication of Temperature in Lower Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

Indication of Temperature in Upper Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

: Temperature display.

Light: Lighting button for LED lamp; it controls the on/off of lamp.

Power: On/off button used to turn on/off all load.

Press Light and Power together for 2 seconds and you can convert between

fahrenheit temperature and Celsius temperature.

Notice!

z The default temperature is 10/10°C, and the temperature after power

failure will be the temperature set before the power failure.

z To elongate the service life of compressor, please wait for at least 5

minutes before the wine cooler is restarted after power failure.

z Failure display

z If there is failure on the sensor, the screen may display failure code, such

as: E and F. When the screen displays the above-mentioned errors, please

do not disassemble it for check by yourself. You should contact local

after-sales service personnel for repair.

z If the temperature in the cooler is too low, it will display “L”.

When the temperature in the cooler is too high, the screen will display “H”

and will flash; under this state, the buzzer will buzz until 30 seconds; one

minute later, the buzzer will continue to give alarm in the next 30 seconds; after

the alarm is given for three times, it will not give alarm any more. You can

press any key to cancel sound alarm.

z When you put a lot of wines together in the cooler, the temperature in the

cooler may rise temporarily.

- 10 -



 este botón ENCIENDE y APAGA la luz.

 este botón ENCIENDE y APAGA la alimentación.

Pulse los botones de  y  al mismo tiempo para

cambiar entre temperaturas Fahrenheit y Celsius.

Indication of Temperature in Lower Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

Indication of Temperature in Upper Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

: Temperature display.

Light: Lighting button for LED lamp; it controls the on/off of lamp.

Power: On/off button used to turn on/off all load.

Press Light and Power together for 2 seconds and you can convert between

fahrenheit temperature and Celsius temperature.

Notice!

z The default temperature is 10/10°C, and the temperature after power

failure will be the temperature set before the power failure.

z To elongate the service life of compressor, please wait for at least 5

minutes before the wine cooler is restarted after power failure.

z Failure display

z If there is failure on the sensor, the screen may display failure code, such

as: E and F. When the screen displays the above-mentioned errors, please

do not disassemble it for check by yourself. You should contact local

after-sales service personnel for repair.

z If the temperature in the cooler is too low, it will display “L”.

When the temperature in the cooler is too high, the screen will display “H”

and will flash; under this state, the buzzer will buzz until 30 seconds; one

minute later, the buzzer will continue to give alarm in the next 30 seconds; after

the alarm is given for three times, it will not give alarm any more. You can

press any key to cancel sound alarm.

z When you put a lot of wines together in the cooler, the temperature in the

cooler may rise temporarily.

- 10 -

Pulse este botón una vez para aumentar la temperatura en 1° F o C.

Pulse este botón una vez para disminuir la temperatura en 1° F o C.

El refrigerador para bebidas puede ser ajustado usando los botones de control de temperatura (echas hacia arriba y hacia

abajo).

El rango de temperatura MÍN. y MÁX. es de 41° a 64°F (5° a 18° C).

CONTROLEs DE LA TEMPERATURA

TEMPERATURE CONTROLs

La temperatura predeterminada para el enfriador el enfriador de bebidas es de 41 ºF (5 ºC). La temperatura luego de una falla 

de alimentación será la temperatura establecida antes de la falla de alimentación.

Para prolongar la vida del compresor, espere al menos 5 minutos antes de reiniciar el enfriador de después de la falla de 

alimentación.



Si se muestra “E” y “F”, comuníquese con el personal de servicio local para su reparación.

Si la temperatura en el enfriador es demasiado baja, se mostrará “L”.

Si la temperatura en el enfriador es demasiado alta, la pantalla mostrará “H” y parpadeará. Bajo este estado, el zumbador 

realizará un zumbido durante 30 segundos. Un minuto más tarde, el zumbador continuará zumbando durante los próximos 30

segundos. Después de tres veces, la alarma no zumbará más. Puede pulsar cualquier tecla para cancelar la alarma de sonido.

Si almacena demasiadas botellas en el enfriador, puede provocar que la temperatura en el enfriador aumente temporalmente.





Press this button once to increase temperature 1° F/C.

Press this button once to decrease temperature 1° F/C.



Pulse este botón una vez para aumentar la temperatura en 1° F o C.

Pulse este botón una vez para disminuir la temperatura en 1° F o C.

Indication of Temperature in Lower Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

Indication of Temperature in Upper Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

: Temperature display.

Light: Lighting button for LED lamp; it controls the on/off of lamp.

Power: On/off button used to turn on/off all load.

Press Light and Power together for 2 seconds and you can convert between

fahrenheit temperature and Celsius temperature.

Notice!

z The default temperature is 10/10°C, and the temperature after power

failure will be the temperature set before the power failure.

z To elongate the service life of compressor, please wait for at least 5

minutes before the wine cooler is restarted after power failure.

z Failure display

z If there is failure on the sensor, the screen may display failure code, such

as: E and F. When the screen displays the above-mentioned errors, please

do not disassemble it for check by yourself. You should contact local

after-sales service personnel for repair.

z If the temperature in the cooler is too low, it will display “L”.

When the temperature in the cooler is too high, the screen will display “H”

and will flash; under this state, the buzzer will buzz until 30 seconds; one

minute later, the buzzer will continue to give alarm in the next 30 seconds; after

the alarm is given for three times, it will not give alarm any more. You can

press any key to cancel sound alarm.

z When you put a lot of wines together in the cooler, the temperature in the

cooler may rise temporarily.

- 10 -

Indication of Temperature in Lower Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

Indication of Temperature in Upper Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

: Temperature display.

Light: Lighting button for LED lamp; it controls the on/off of lamp.

Power: On/off button used to turn on/off all load.

Press Light and Power together for 2 seconds and you can convert between

fahrenheit temperature and Celsius temperature.

Notice!

z The default temperature is 10/10°C, and the temperature after power

failure will be the temperature set before the power failure.

z To elongate the service life of compressor, please wait for at least 5

minutes before the wine cooler is restarted after power failure.

z Failure display

z If there is failure on the sensor, the screen may display failure code, such

as: E and F. When the screen displays the above-mentioned errors, please

do not disassemble it for check by yourself. You should contact local

after-sales service personnel for repair.

z If the temperature in the cooler is too low, it will display “L”.

When the temperature in the cooler is too high, the screen will display “H”

and will flash; under this state, the buzzer will buzz until 30 seconds; one

minute later, the buzzer will continue to give alarm in the next 30 seconds; after

the alarm is given for three times, it will not give alarm any more. You can

press any key to cancel sound alarm.

z When you put a lot of wines together in the cooler, the temperature in the

cooler may rise temporarily.

- 10 -

Indication of Temperature in Lower Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

Indication of Temperature in Upper Chamber

: Press this button once and the temperature increase 1°C.

: Press this button once and the temperature decrease 1°C.

: Temperature display.

Light: Lighting button for LED lamp; it controls the on/off of lamp.

Power: On/off button used to turn on/off all load.

Press Light and Power together for 2 seconds and you can convert between

fahrenheit temperature and Celsius temperature.

Notice!

z The default temperature is 10/10°C, and the temperature after power

failure will be the temperature set before the power failure.

z To elongate the service life of compressor, please wait for at least 5

minutes before the wine cooler is restarted after power failure.

z Failure display

z If there is failure on the sensor, the screen may display failure code, such

as: E and F. When the screen displays the above-mentioned errors, please

do not disassemble it for check by yourself. You should contact local

after-sales service personnel for repair.

z If the temperature in the cooler is too low, it will display “L”.

When the temperature in the cooler is too high, the screen will display “H”

and will flash; under this state, the buzzer will buzz until 30 seconds; one

minute later, the buzzer will continue to give alarm in the next 30 seconds; after

the alarm is given for three times, it will not give alarm any more. You can

press any key to cancel sound alarm.

z When you put a lot of wines together in the cooler, the temperature in the

cooler may rise temporarily.

- 10 -



 este botón ENCIENDE y APAGA la luz.

 este botón ENCIENDE y APAGA la

alimentación.

Pulse los botones de  y  al

mismo tiempo para cambiar entre temperaturas

Fahrenheit y Celsius.

La temperatura predenida es 46°F (8°C) para la zona superior y 59°F (15°C) para zona más baja. La temperatura luego de una 

falla de alimentación será la temperatura establecida antes de la falla de alimentación.