Briggs & Stratton 071035-00 User manual

Brand: Briggs & Stratton

Model: 071035-00

Category: Power generators

Type: User manual

Installation &

Operator’s Manual

Questions?

Help is just a moment away!

Call: Helpline

(800) 743-4115 M-F 8-5 CT

BRIGGSandSTRATTON.COM

Model 071013 Revision 01

201925GS Rev. A (04/23/2007)

Briggs & Stratton Power Products Group, LLC

900 North Parkway

Jefferson, WI 53549

transmitted in any form by any means without the express written

permission of Briggs & Stratton Power Products Group, LLC.

Thank you for your purchase of this Briggs & Stratton Power Products Power Management System. This product is intended

for use with Briggs & Stratton Home Standby Generator sets ONLY. This is an optional home standby system which provides

an alternate source of electric power and to serve loads such as a gas furnace, refrigeration and communication systems that,

when stopped during any power outage, could cause discomfort, or the like. This product DOES NOT qualify for emergency

standby as defined by NFPA 70 (NEC).

This manual contains safety information to make you aware of the hazards and risks associated with power management

systems and how to avoid them. Briggs & Stratton has made every effort to provide for a safe, streamlined and cost-effective

installation. Each installation is unique, it is impossible to know of and advise of all conceivable procedures and methods by

which installation might be achieved. We do not know all possible hazards and/or the results of each method or procedure.

Save these instructions for future reference.

This power management system requires installation before use. Refer to the Installation section of this manual for

instructions on installation procedures. Only licensed electrical contractors should install power management systems.

Installations must strictly comply with all applicable federal, state and local codes, standards and regulations.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your power management system. Consult your

Yellow Pages. There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service. You

can also contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet at

BRIGGSandSTRATTON.COM.

Power Management System

Model Number

Revision

Serial Number

Date Purchased

1
FrançaisEspañol
Table Of Contents
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Owner Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installer Responsibilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Equipment Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Mounting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Power Wiring Interconnections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
System Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Testing the Power Management System . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Wiring Decal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Electrical Load Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Illustrated Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2 BRIGGSandSTRATTON.COM

Important Safety Instructions

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all

safety messages that follow this symbol to avoid

possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION, WARNING), a pictorial and/or a safety

message to alert you to hazards. DANGER indicates a hazard

which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury. CAUTION indicates a hazard

which, if not avoided, might result in minor or moderate

injury. NOTICE indicates a situation that could result in

equipment damage. Follow safety messages to avoid or

reduce the risk of injury or death.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that it

is safe for you and others. You must also make sure that the

procedure, work method or operating technique that you

choose does not render the power management system

unsafe.

Save These Instructions

• Use power management system only for intended uses.

• If you have questions about intended use, ask dealer or contact

Briggs and Stratton Power Products.

• Do not expose power management system to excessive

moisture, dust, dirt, or corrosive vapors.

• Remain alert at all times while working on this equipment. Never

work on the equipment when you are physically or mentally

fatigued.

• If connected devices overheat, turn them off and turn off their

circuit breaker/fuse.

NOTICE

Improper treatment of power management system can

damage it and shorten its life.

• Do not touch bare wires.

• Do not use power management system with worn, frayed, bare

or otherwise damaged wiring.

• Do not handle electrical cords while standing in water, while

barefoot, or while hands or feet are wet.

• If you must work around a unit while it is operating, stand on an

insulated dry surface to reduce shock hazard.

• Do not allow unqualified persons or children to operate or

service power management system.

• In case of an accident caused by electrical shock, immediately

shut down all sources of electrical power and contact local

authorities. Avoid direct contact with the victim.

WARNING

Failure to properly ground power management

system can result in electrocution.

• Despite the safe design of the power management system,

operating this equipment imprudently, neglecting its

maintenance or being careless can cause possible injury or

death.

WARNING

Power management system contains high voltage

that can cause personal injury or death.

• Failure to follow above warning could cause personal injury,

damage and/or malfunction of equipment.

WARNING

Low voltage wire cannot be installed in same

conduit as power voltage wiring.

WARNING

Only qualified electricians should attempt installation of

this system, which must strictly comply with applicable

codes, standards and regulations.

Introduction

Your Briggs & Stratton Power Management System is

supplied with this combined “Installation and Operator’s

Manual”. This is an important document and should be

retained by the owner after the installation has been

completed.

Every effort has been expended to make sure that the

information in this manual is both accurate and current.

However, the manufacturer reserves the right to change, alter

or otherwise improve the system at any time without prior

notice.

For the Home Owner

To help you make informed choices and communicate

effectively with your installation contractor(s),

Read and understand the Owner Orientation Section

of this manual before contracting or starting your

power management system installation.

To arrange for proper installation, contact the store at which

you purchased your power management system, your dealer,

or your utility power provider.

The power management system warranty is VOID

unless the system is installed by a

licensed electrical professional.

Owner Orientation

The illustrations provided are for typical circumstances and

are meant to familiarize you with the installation options

available with your power management system.

Local codes, appearance, and distances are the factors that

must be considered when negotiating with an installation

professional. As the distance from the existing electrical

service increases, compensation in wiring materials must be

allowed for. This is necessary to comply with local codes and

overcome electrical voltage drops.

The factors mentioned above will have a direct effect on

the overall price of your power management system

installation.

NOTE: Your installer must check local codes AND obtain

permits before installing the system.

• Read and follow the instructions given in this manual.

• Follow a regular schedule in caring for and using your

power management system, as specified in this

manual.

Installer Responsibilities

• Read and observe the safety rules.

• Read and follow the instructions given in this manual.

• Check federal, state and local codes.

• Consult with owner to determine loads to be controlled

and their priorities.

NOTE: A worksheet for determining which loads are to be

transferred and their priorities is provided on page 9.

• The installer may need to provide appropriate rated

contactors based on loads to be controlled.

Equipment Description

The power management system is designed to control

six priority loads and up to two air conditioner loads that are

being supplied by power from the home standby system.

This power management system goes into a STANDBY mode

and does not control any loads when utility power is present.

The power management system consists of a relay board

with 6 relays to control loads rated up to 120 VAC, 20 Amps,

1 hp, and a control module that has 2 relays for central air

conditioner loads. The circuit boards are housed in a NEMA

3R enclosure that is suitable for both indoor and outdoor

installations.

Two (2) current transformers monitor generator current at

the transfer switch to ensure that the loading of the

generator does not exceed 85 percent. Should load exceed

85 percent, the power management system will shed loads

to keep the generator from overloading. The power

management system will add load back once sufficient

current is available.

The control module has a green LED for each relay to

indicate when the relays are supplying power to the loads

when on generator power. There is also a status LED that

flashes when the power management system is functioning

properly.

Installation

Unpacking

Delivery Inspection

After removing the carton, carefully inspect the power

management system components for any damage that may

have occurred during shipment.

IMPORTANT: If loss or damage is noted at time of delivery,

have the person(s) making delivery note all damage on the

freight bill and affix his signature under the consignor's

memo of loss or damage. If loss or damage is noted after

delivery, contact the carrier for claim procedures. Missing or

damaged parts are not warranted.

Shipment Contents

• Power Management System

• Installation and Operator’s Manual

• Wire Connectors (4)

• 1/4” Double Male, Single Female Lugs (2)

Mounting Guidelines

The power management system is enclosed in a NEMA

Type 3R enclosure suitable for indoor/outdoor use.

Guidelines for mounting the power management system

include:

• Install power management system on a firm, sturdy

supporting structure.

• The power management system must be installed with

minimum NEMA 3R hardware for conduit connections.

• Level and plumb the enclosure. This can be done by

placing washers between the power management

system enclosure and the mounting surface.

• Never install the power management system where any

corrosive substance might drip onto the enclosure.

• Protect the power management system at all times

against excessive moisture, dust, dirt, lint, construction

grit and corrosive vapors.

A typical installation of the power management system is

depicted below. It is best if it is mounted near the main

breaker panel, either inside or outside. Discuss layout

suggestions/changes with the owner before beginning the

system installation process.

4 BRIGGSandSTRATTON.COM

Main

Breaker

Panel

Transfer

Switch

Hot

Water

Heater

Air

Conditioner

Service Disconnect

Generator

Watt -

Hourmeter

Branch Circuits

Disconnect Switch

Power

Manage-

ment

System

Contactor

Power Wiring Interconnections

All wiring must be the proper size, properly supported and

protected by conduit. All wiring should be done per

applicable federal, state and local codes, standards and

regulations.

Complete the following connections between the transfer

switch, power management system and main breaker panel.

Also see the Wiring Decal on page 8.

1. Set generator’s system switch to OFF position.

2. Set generator’s main circuit breaker to OFF (open)

position.

3. Identify loads and their priorities (using list developed

with owner) to be transferred to power management

system in main breaker panel.

4. In main breaker panel, turn selected load circuit

breakers to OFF position.

5. Connect “GND” lug to an approved ground.

NOTE: Assure grounding electrode conductor is connected

and bonded per applicable federal, state and local codes,

standards and regulations.

6. Using installer supplied 300VAC or greater wire and

supplied 1/4” double male, single female lugs, connect

generator 240VAC from transfer switch to relay board

in power management system.

7. Unplug current transformers from control module in

transfer switch.

Ground Lug

To Transfer Switch

Air Conditioner

Relays

Load

Connection

Control

Module

Test

Button

Generator

Connection

Air Conditioner

Connections

Relay Board

To Air Conditioners

Transfer Switch

Connections

Green LED’s

Wireways

• Failure to follow above warning could cause personal injury,

damage and/or malfunction of equipment.

WARNING

Low voltage wire cannot be installed in same

conduit as power voltage wiring.

• Remove all power prior to installing this power management

system. Failure to do so could cause internal damage to the

board when making electrical connections.

• Turn generator to OFF position.

• Turn off utility power to the home standby generator and transfer

switch.

NOTICE

Improper installation can cause damage to the circuit

boards and shorten their life. Installing circuit boards in live

circuits will damage the board and is not a warranty

condition. ALWAYS disconnect ALL sources of power prior

to servicing.

8. Cut two pin connector ends off of current transformer

leads and discard. Strip wires and place in supplied

wire connectors.

9. Using installer supplied 300VAC or greater wire, run

wires from wire connectors to control module terminal

block labeled “CT1A” through “CT2B” in power

management system.

10. Using installer supplied 300VAC or greater wire,

connect C (Common) and NO (Normally Open)

terminals on terminal strip J9 of control module in

transfer switch to control module terminal block labeled

“TXSF” and “TXFG” in power management system.

11. Wire the air conditioner thermostat control wiring to the

control module labeled “AC1A-AC2B” in power

management system.

NOTE: AC1A and AC1B is for the priority 1 air conditioner.

AC2A and AC2B is for the priority 2 air conditioner.

12. For 120VAC selected loads, remove wire from selected

load circuit breaker.

13. Using installer supplied 300VAC or greater wire,

connect selected load circuit breaker to terminal block

at power management system labeled “CB/B1” for

priority 1 load.

14. Using installer supplied 300VAC or greater wire and a

wire nut, connect the selected load wire to terminal

block in power management system labeled “RLY/B1”

for priority 1 load.

15. Repeat steps 12 through 14 for all other 120VAC

priorities using terminals “CB/C1” through “RLY/D2”.

16. For 240VAC selected loads, remove both wires from

selected load circuit breaker and place in load side of

installer supplied contactor.

17. Using installer supplied 300VAC or greater wire,

connect circuit breaker to line side of contactor.

18. Using installer supplied 300VAC or greater wire,

connect one pole of the circuit breaker to terminal block

in power management system labeled “CB/B1” for a

priority 1 load.

19. Using installer supplied 300VAC or greater wire,

connect Neutral in main breaker panel to contactor coil.

20. Using installer supplied 300VAC or greater wire,

connect contactor coil to terminal block in power

management system labeled “RLY/B1” for a priority 1

load.

21. Repeat steps 16 through 20 for all other 240VAC

priorities using terminals “CB/C1” through “RLY/D2”.

22. Tighten all wire connections/fasteners to proper torque.

See inside power management system enclosure for

proper torque values.

System Setup

You must perform the following before operating the system:

• Place the switch labeled “SW2” on the control module

in the NG or LP position, whichever is appropriate for

the installed home standby system.

• Place the switch labeled “SW3” on the control module

to match the rating of the home standby system.

• In main breaker panel, turn selected load circuit

breakers to the ON position.

IMPORTANT: After installation of the power management

system is complete, turn on utility power to the home

standby generator and transfer switch. Wait one minute

before turning generator to AUTO.

6 BRIGGSandSTRATTON.COM

SW3

SW2

Location of J9 Terminal Strip in Transfer Switch

Testing the Power Management System

With the generator in “AUTO“ position, turn the service

disconnect feeding the transfer switch contactor to the “Off”

position. The generator will start and the transfer switch will

transfer to generator power.

Press the test button on the control module of the power

management system. As the button is pressed, a relay will

energize. Each time the button is pressed, the previous relay

that was energized, will de-energize and the next relay will

energize.

Press the test button once and relay B2 will energize. Press

the test button again and B2 will de-energize and relay C1 will

energize. This will proceed until all relays have been tested or

if the test button has not been pressed for a period of 30

seconds, the test sequence will halt and the system will go

back to automatic control.

To go back to utility power, turn the service disconnect

feeding the transfer switch contactor to the “On” position.

Controls

There are no operator controls in this Power Management

System.

Operation

When the home standby system is providing power to the

transfer switch, the power management system is constantly

monitoring generator power to control loads. The power

management system monitors both incoming generator lines

and keeps the home standby system loaded to a maximum

of 85-86 percent of rated load. When the current

transformers on any line start to see current reach 85-86

percent of rated load, the power management system will

start shedding loads based on the lowest priority and work

its way to the highest priority. When current has dropped

below 85-86 percent of rated load, the power management

system will start to add loads based on the highest priority

first, followed by the second highest until the generator

reaches 85-86 percent load or all priorities are back on line.

The power management system will operate this way until

the transfer switch transfers back to utility position.

The power management system waits 5 seconds between

adding or shedding each load to permit the system to

stabilize. When a relay is opened, the relay will stay opened

for a minimum of 5 minutes or until the load can be added

without putting the generator over 85-86 percent of rated

load. If a large load demand is seen, the power management

system will shed all loads in less than 1.5 seconds to

prevent the generator from overloading. Once the demand

has stabilized, the power management system will start with

the highest priority, wait 5 seconds and then add the next

priority. The unit will continue to do this until all loads are

added or 85-86 percent of rated load is reached.

When the generator is powering loads, the A/C relays are

open. When one or both of the relays sense 24VAC from the

thermostat(s), the controller will shed loads B1-D2, and then

will allow only one A/C relay to close. A1 has priority over

A2. A2 can close when the signal for A1 has expired. When

the A/C’s are being called to run, all loads are to be shed

before the A/C unit can be added. Should A/C 1 call while

A/C 2 is running, A/C 2 shall open, all relays would open and

then A/C 1 can close. When the A/C relays open, they are to

be locked out for a minimum of 5 minutes or until they

receive a call to start the A/C.

8 BRIGGSandSTRATTON.COM

Wiring Decal

Priority 120VAC Electrical Appliances Priority 240VAC Electrical Appliances

Window Air Conditioner 1 Central Air Conditioner 1

Window Air Conditioner 2 Central Air Conditioner 2

Window Air Conditioner 3 Range/Stove

Refrigerator 1 Dryer

Refrigerator 2 Well Pump

Freezer 1 Hot Tub

Freezer 2 Pool Heater

Microwave Water Heater

Bathroom Other:________________________

Auxiliary Heater Other:________________________

Home Theater System Other:________________________

Garage Heater

Sink Water Heater

Sewage Lift Pump

Other:________________________

IMPORTANT: DO NOT connect furnace, sewage pump and sump pump to power management system.

Electrical Load Worksheet

10 BRIGGSandSTRATTON.COM

Maintenance

The power management system is designed to be

maintenance free under normal usage. However, inspection

and maintenance checks should be made on a regular basis.

Maintenance will consist mainly of keeping the power

management system clean.

Visual inspections should be done at least once a month.

Access to power management system must not be

obstructed. Keep 3 feet (92 cm) clearance around power

management system. Check for an accumulation of dirt,

moisture and/or corrosion on and around the enclosure,

loose parts/hardware, cracks and/or discoloration to

insulation, and damaged or discolored components.

Exercise the power management system at least once every

three months as described in the previous section Testing

the Power Management System unless a power outage

occurs and Home Generator System has gone through

automatic sequence. Allow generator to run for at least

30 minutes.

Contact a licensed electrical professional to inspect and clean

the inside of your power management system at least once a

year.

When Calling the Factory

Before contacting Briggs & Stratton regarding service or

repair of this power management system, obtain the Model

Number and Serial Number from the unit data decal located

on or inside the enclosure.

To contact Briggs & Stratton call (800) 743-4115, between

8:00 AM and 5:00 PM CT.

Specifications

Rated AC Voltage . . . . . . . . . . . . . . . . . . . . . . .125/250 Volts

Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50/60 Hz

Relay Contacts

Rating . . . . . . . . . .125 VAC, 20A, 1 HP, 768 VA Pilot Duty

Dimensions . . . . . .Approximately 16” H X 12” W X 6” Deep

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 lbs.

Troubleshooting

Problem Cause Correction

Supervised loads (air conditioner, etc.)

are not operating when generator is

supplying power

1. AC1A-AC2B contacts not operating

correctly.

2. Too much load on generator.

3. Current transformer not connected.

4. Broken current transformer.

5. Status LED stays lit constantly.

1A. Check AC1A-AC2B contacts for

proper operation.

B. Check control wiring to external

load.

C. Check harness between boards is

properly connected.

D. Check that there is 24 VAC to one of

the terminals.

E. Be sure 5 minute lock out has

elapsed.

F. Be sure air conditioner start time

delay has elapsed.

2. Decrease load to generator.

3. Connect current transformer.

4. Replace current transformer.

5. Contact an authorized service

center.

12 BRIGGSandSTRATTON.COM

Illustrated Parts List

Item Part # Description

1 NSP ENCLOSURE

2 196616GS BOARD, Load Control Center Relay

3 197979GS SPACER, PCB Board, 1/2"

4 198112GS HARNESS, Wire, Load Control

Center

5 201924GS BOARD, Load Control Center

6 198431GS CLIP, Latching Wire

7 * NUT, 1/4 - 20

8 * WASHER, Lock 1/4

9 186345GS TERMINAL

10 * WASHER, Shakeproof, Ext M6 - 1/4

11 192150GS SPACER

12 202426GS DECAL

13 198655GS DECAL, Warning

Item Part # Description

14 * PPHMS, 8-32 x 1

15 200574GS SPACER, 4 x 25

16 * NUT, Hex, 8 - 32, w/Locking Insert

Items Not Illustrated

195728GS CURRENT TRANSFORMER

201925GS MANUAL, Load Control Center

197956GS BLOCK, Terminal w/ Levrs

74094GS LUG, 1/4 Tab

77211GS LUG, 1/4, 18-22

* - Items without part numbers are common fasteners and

are available at local hardware stores.

Warranty

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC TRANSFER SWITCH OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the equipment that is defective in material or

workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This

warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in

our dealer locator map at BRIGGSandSTRATTON.COM.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW. ANY AND ALL IMPLIED WARRANTIES ARE

EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some

states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and

you may also have other rights which vary from state to state or country to country.

3 years

None

Consumer Use

Commercial Use

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the

table above. “Consumer use" means personal residential household use by a retail consumer. “Commercial use" means all other uses, including use for

commercial, income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter be considered as commercial use for

purposes of this warranty. Equipment used for prime power in place of utility are not applicable to this warranty.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF PURCHASE

RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED, THE MANUFACTURING

DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most warranty

repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not apply if

equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation. Similarly, the

warranty is void if the manufacturing date or the serial number on the equipment has been removed or the equipment has been altered or modified. During

the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under normal

use and service. This warranty will not cover the following repairs and equipment:

• Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty does not cover

repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized installation or

alteration and modification, misuse, negligence, accident, overloading, improper maintenance, repair or storage so as, in our judgment, to adversely

affect its performance and reliability. This warranty also does not cover normal maintenance such as adjustments, cleaning and fuse replacement.

• Other Exclusions: This warranty excludes wear items or damage or malfunctions resulting from accidents, abuse, modifications, alterations, or

improper servicing. Accessory parts are excluded from the product warranty. This warranty excludes failures due to acts of God and other force

majeure events beyond the manufacturers control. Also excluded is used, reconditioned, and demonstration equipment.

198180E, Rev. C, 12/31/2006

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WI, USA

Effective November 1, 2005 replaces all undated Warranties and all Warranties dated before November 1, 2005

WARRANTY PERIOD

Reserved

Manual de

Instalación

y del Operario

Preguntas? La ayuda es justa

un momento lejos!

Llamada: Línea Directa

(800) 743-4115 M-F 8-5 CT

BRIGGSandSTRATTON.COM

Briggs & Stratton Power Products Group, LLC.

900 North Parkway

Jefferson, WI 53549

Reservados todos los derechos. Queda prohibida la reproducción o

transmisión total o parcial de este material, sea cual sea la forma y

el medio empleados para ello, sin el permiso previo y por escrito

de Briggs & Stratton Power Products Group, LLC.

Gracias por comprar este sistema de gestión de energía Briggs & Stratton Power Products. Este producto es un sistema

doméstico de reserva opcional y proporciona una fuente alternativa de energía eléctrica con capacidad para alimentar cargas

tales como calderas de gas y sistemas de refrigeración y de telecomunicaciones, que cuando dejan de funcionar a causa de

una interrupción de la alimentación eléctrica de la red pueden producir incomodidades o problemas. Este producto no

pertenece a la categoría de reserva de emergencia según lo definido por la norma NFPA 70 (NEC).

Este manual contiene información de seguridad sobre los riesgos asociados con los sistemas de gestión de energía y sobre

cómo evitarlos. Briggs & Stratton ha realizado el máximo esfuerzo para que la instalación resulte segura, sencilla y

económica. Cada instalación es única, lo que hace imposible conocer y recomendar todos los procedimientos y métodos

posibles para efectuarla. No conocemos todos los riesgos y/o resultados posibles de cada método o procedimiento. Guarde

estas instrucciones para futuras consultas.

Antes de utilizar el sistema de gestión de energía, es necesario instalarlo. Consulte en la sección Instalación de este

manual las instrucciones o procedimientos de instalación. Los sistemas de gestión de energía sólo deben ser instalados

por electricistas cualificados. Las instalaciones deben cumplir estrictamente la totalidad de la normativa vigente.

Dónde encontrarnos

Nunca tendrá que buscar mucho para poder obtener soporte y servicio técnico de Briggs & Stratton para su sistema de

gestión de energía. Consulte las páginas amarillas. Hay más de 30.000 distribuidores de servicio autorizados Briggs &

Stratton en todo el mundo que le ofrecerán un servicio de calidad. También puede dirigirse al departamento de servicio al

cliente de Briggs & Stratton llamando al (800) 743-4115 o por Internet, en el sitio web BRIGGSandSTRATTON.COM.

Sistema de Gestión de Energía

Número de Modelo

Revisión

Número de Serie

Fecha de compra

1
Español
Instrucciones importantes de seguridad . . . . . . . . . . . . . . . . . . . . . . . . . 2
Orientación para el Propietario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Responsabilidades del Instalador . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Descripción del Equipo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Instalacion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Desempaque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pautas de Montaje . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Interconexiones de Cableado de Energía . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Configuración del Sistema. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Prueba del sistema de gestión de energía eléctrica . . . . . . . . . . . . . . . . . . . 7
Mandos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Sistema Funcionamiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Alambrar la calcomanía . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hoja de trabajo de cargas eléctricas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mantenimiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Especificaciones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Reparacion de Averias . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Garantia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Tabla de Contenido

2 BRIGGSandSTRATTON.COM

Instrucciones importantes de

seguridad

Éste es el símbolo de alerta de seguridad. Sirve

para advertir al usuario de un posible riesgo para

su integridad física. Siga todos los mensajes de

seguridad que figuren después de este símbolo

para evitar lesiones o incluso la muerte.

El símbolo de alerta de seguridad ( ) se utiliza con una

palabra de señalización (PELIGRO, PRECAUCIÓN,

ADVERTENCIA), una imagen y/o un mensaje de seguridad

para advertir al usuario de un riesgo. PELIGRO indica un

riesgo que, de no evitarse, provocará la muerte o lesiones de

gravedad. ADVERTENCIA indica un riesgo que, de no

evitarse, puede provocar la muerte o lesiones de gravedad.

PRECAUCIÓN indica un riesgo que, de no evitarse, puede

provocar lesiones moderadas. Cuando se utiliza sin el

símbolo de alerta, AVISO indica una situación que podría

producir daños en el equipo. Siga en todo momento los

mensajes de seguridad para evitar o reducir el riesgo de

lesiones y de muerte.

El fabricante no puede prever todas las posibles

circunstancias que pueden implicar riesgos. Por lo tanto, las

advertencias que aparecen en este manual y las etiquetas y

calcomanías adheridas a la unidad no incluyen todas las

posibilidades. Si aplica un procedimiento, método de trabajo

o técnica de operación no recomendada específicamente por

el fabricante, debe estar seguro de que se trata de una

práctica segura para usted y para otras personas. También

debe asegurarse de que el procedimiento, método de trabajo

o técnica de operación que elija, no haga que el sistema de

gestión de energía eléctrica se torne inseguro.

Conserve estas instrucciones

ADVERTENCIA

Únicamente los electricistas capacitados pueden intentar

instalar este sistema. Dicha instalación debe cumplir

estrictamente con los códigos, las regulaciones y las

normas correspondientes.

• Si no se respeta esta indicación pueden producirse lesiones,

daños y/o fallos de funcionamiento del equipo.

ADVERTENCIA

Los cables de baja tensión no se pueden instalar

en el mismo conducto que los cables de

suministro de energía.

• No toque los alambres pelados o receptáculos.

• No use un sistema de gestión de energía eléctrica con cables

eléctricos que estén malgastados, rotos, pelados o dañados de

cualquier forma.

• No maneje el cables eléctricos mientras esté parado en agua,

descalzo o cuando las manos y los pies estén mojados.

• Si fuera necesario realizar trabajos en cercanías de la unidad

mientras está en funcionamiento, párese sobre una superficie

seca y aislada para reducir los riesgos de una descarga.

• No permita que personas descalificadas o niños operen o sirvan

al sistema de gestión de energía eléctrica.

• En caso de que se produzca un accidente causado por una

descarga eléctrica, cierre inmediatamente la fuente de energía

eléctrica y contacta administración local. Evite el contacto

directo con la víctima.

ADVERTENCIA

Si no hace tierra apropiadamente con un sistema

de gestión de energía eléctrica, puede hacer que

ocurra un electrocutamiento.

• A pesar del diseño seguro del sistema de gestión de energía

eléctrica, si se opera este equipo en forma imprudente, si no se

cumple con el mantenimiento o si se actúa con descuido, se

pueden producir lesiones o la muerte.

ADVERTENCIA

El sistema de gestión de energía eléctrica contiene

alta tensión que puede provocar lesiones o la

muerte.

• Use el sistema de gestión de energía eléctrica solamente con la

finalidad para el cual fue diseñado.

• Si usted tiene alguna pregunta acerca de las finalidades de uso

del generador, pregúntele a su concesionario o contacte a Briggs

& Stratton.

• NO exponga al sistema de gestión de energía eléctrica a una

humedad excesiva, polvo, suciedad o vapores corrosivos.

• Permanezca siempre alerta cuando trabaje con este equipo.

NUNCA trabaje con este equipo si se siente cansado física o

mentalmente.

• Si se calientan excesivamente los dispositivos conectados,

apáguelos y abra sus interruptores o quite sus fusibles.

AVISO

El tratamiento inadecuado del sistema de gestión de

energía eléctrica puede dañarlo y acortar su vida

productiva.

Page is loading ...

Briggs & Stratton 071035-00 User manual

Brand: Briggs & Stratton

Model: 071035-00

Category: Power generators

Type: User manual

Download PDF

report

in other languages

français: Briggs & Stratton 071035-00 Manuel utilisateur
español: Briggs & Stratton 071035-00 Manual de usuario

Briggs & Stratton 071035-00 User manual

Briggs & Stratton 071035-00 User manual

in other languages

Related papers

Other documents