Page is loading ...
2
English
Technical Information
Water pressure
Recommended 15 - 75 PSI (0.1 - 0.5 MPa)
Maximum 145 PSI (1 MPa)
Hot water temp.
Recommended 120°-140° F*(48° -60° C*)
Maximum 158°F*(70° C*)
Max. flow rate 1.2 GPM (4.5 L/min)
Hole size in mounting surface
spout 1⁵⁄₁₆" (34 mm)
valves 1³⁄₁₆" (30 mm)
Max. depth of mounting surface 1³⁄₁₆" (30 mm)
* Please know and follow all applicable local plumbing
codes when setting the temperature on the water
heater.
Installation Considerations
• For best results, Hansgrohe recommends that
this unit be installed by a licensed, professional
plumber.
• Please read over these instructions thoroughly
before beginning installation. Make sure that
you have all tools and supplies needed to
complete the installation.
• The drain is suitable for most, but not all, lavatory
sinks sold in the United States and Canada.
• This drain is intended for use in a sink with an
overflow. If your sink does not have an overflow,
or if this drain is too small for the hole in your
sink, please refer to the instructions
included with the sink. Some sinks include
special drain installation instructions and/
or parts. Others require the use of a specialty
drain. Hansgrohe is not respnsible for the cost
of a specialty drain.
The hot and cold supply hoses included
with this faucet are for use with ⅜ stops.
If your stops are a different size, purchase
adapters at your local plumbing supply
store or home center. Adapters are not
available from Hansgrohe.
• Keep this booklet and the receipt (or other proof
of date and place of purchase) for this product
in a safe place. The receipt is required should it
be necessary to request warranty parts.
Page is loading ...
Page is loading ...
Page is loading ...
6
English Français
Español
Installation / Installation / Instalación
Place the hot and cold valve
assemblies on the mounting
surface. The hot valve should
be on the left, the cold valve on
the right.
Rest the valve on the mounting
surface.
Install the fiber washer, metal
washer, and mounting nut.
Do not fully tighten the nut at
this time.
Placez les ensembles de valve
d’eau chaude et d’eau froide
sur la surface de montage. La
valve d’eau chaude doit être à
gauche, et celle de l’eau froide
à droite.
Déposez la valve sur la surface
de montage.
Installez la rondelle en fibre, la
rondelle métallique et l’écrou de
montage.
Ne serrez pas l’écrou à fond
pour l’instant.
Coloque las válvulas de agua
fría y caliente sobre la superfi-
cie de montaje. La válvula de
agua caliente debe estar a la
izquierda y la de agua fría a la
derecha.
Apoye la válvula en la superficie
de montaje.
Instale la arandela de fibra, la
arandela metálica y la tuerca de
montaje.
No apriete la tuerca completa-
mente en este momento.
red
rouge
rojo
1
2
1 2
7
English
Français
Español
Inspect the alignment of the
handles.
If necessary, rotate the valve.
Vérifiez l’alignement des
poignées.
Au besoin, tournez la valve.
Inspeccione la alineación de las
manijas.
Si es necesario, gire la válvula.
3 4
8
English Français
Español
Tighten the nut. Tighten the
tensioning screws.
Install the drain pull rod on the
spout.
Serrez l’écrou. Serrez les vis de
pression.
Installez la tige d’entraînement
du trou d’écoulement sur le bec.
Apriete la tuerca. Apriete los
tornillos tensores.
Instale el tirador de drenaje en
el surtidor.
5
6
2.2 ft-lb
3 Nm
9
English
Français
Español
Position the sealing ring on the
mounting surface.
Position the spout on the mount-
ing surface.
Install the fiber washer, metal
washer, and mounting nut.
Tighten the tensioning screws.
Placez le joint sur la surface de
montage.
Placez le bec sur la surface de
montage.
Installez la rondelle en fibre, la
rondelle métallique et l’écrou de
montage.
Serrez les vis de pression.
Coloque el retén anular sobre la
superficie de montaje.
Coloque el surtidor sobre la
superficie de montaje.
Instale la arandela de fibra, la
arandela metálica y la tuerca de
montaje.
Apriete los tornillos tensores.
2.2 ft-lb
3 Nm
8
7
10
English Français
Español
Open the quick-connect by
pushing it upwards.
Insert the connection angle in
the spout quick-connect.
Ouvrez la douille de raccord
rapide en la poussant vers le
haut.
Insérez le coude de raccorde-
ment dans la douille de raccord
rapide du bec.
Abra la conexión rápida empu-
jándola hacia arriba.
Inserte el codo de conexión en
la conexión rápida del surtidor.
9 10
11
English
Français
Español
Lock the quick-connect by pulling
down on it.
Connect the hot and cold supply
hoses to the stops.
Verrouillez la douille de raccord
rapide en la tirant vers le bas.
Connectez les tuyaux d’arrivée
d’eau chaude et d’eau froide
aux butées d’arrêt.
Trabe la conexión rápida tiran-
do hacia abajo.
Conecte las mangueras de sum-
inistro de agua caliente y fría a
los topes.
9 mm
16 mm
11 12
12
English Français
Español
Open the quick-connect on
one of the connection hoses by
pushing it upwards.
Push the quick-connect over one
of the inlets on the connection
angle.
Ouvrez la douille de raccord
rapide de l’un des tuyaux de
raccordement en la poussant
vers le haut.
Poussez la douille de rac-
cord rapide sur l’une des
orifices d’arrivée du coude de
raccordement.
Abra la conexión rápida en una
de las mangueras de conexión
empujándola hacia arriba.
Presione la conexión rápida
sobre una de las entradas en el
codo de conexión.
13 14
13
English
Français
Español
Lock the quick-connect by
pushing it toward the connection
angle.
Repeat with the second connec-
tion hose.
Remove the aerator.
Verrouillez la douille de raccord
rapide en la poussant vers le
coude de raccordement.
Répétez l’opération pour le sec-
ond tuyau de raccordement.
Retirez l’aérateur.
Trabe la conexión rápida empu-
jándola hacia el codo.
Repita con la segunda mangu-
era de conexión.
Retire el aireador.
15 16
1
2
14
English Français
Español
Flush the hot and cold supply
lines for at least two minutes.
Reinstall the aerator.
Rincez les conduites d’ali-
mentation d’eau chaude et
d’eau froide pendant au moins
deux minutes.
Réinstallez l’aérateur.
Purgue los suministros de agua
caliente y agua fría durante al
menos dos minutos.
Reinstale el aireador.
> 2 min
17
18
1.5 ft-lb
2 Nm
15
Installation / Installation / Instalación
Petroleum-based plumbers putty can
damage the surface of some sinks.
Please consult the manufacturer of the
sink regarding compatible sealants.
Les mastics de plomberie à base de pé-
trole peuvent endommager la surface
de certains lavabos. Veuillez consulter
le fabricant du lavabo pour connaître
les scellants compatibles.
Masilla de petróleo-basó puede da-
ñar la superficie de algún bañeras.
Consulte por favor al fabricante del
bañera con respecto a selladores
aceptables.
shorter
plus court
más corto
longer
plus long
más largo
1 2
3 4 5
76
1
2
1
2
1
2
3
16
Joleena
04774XXX
Replacement Parts / Pièces détachées / Repuestos
xx = Colors / Couleurs / Acabados
00 = Chrome
67 = Matte Black
82 = Brushed Nickel
83 = Polished Nickel
92914000
(400 mm)
96321001
(450 mm)
98932000
93554XXX
95366001
98817001
92907000
(33x2.5)
97827000
(8x1.75)
97827000
(8x1.75)
92909000
92909000
97548000
92913000
(200 mm)
(M4x6)
88509xx0
92905000
93553XXX
93530XXX
93531XX1
93555XXX
Page is loading ...
18
Cleaning Recommendation for Hansgrohe Products
Modern bathroom faucets, kitchen faucets and shower products are made from different materials to comply with the
needs of the market with regard to design and functionality. To avoid damage to the product, it is necessary to take
proper care of it.
For best results:
• Prevent the buildup of mineral scale and /or soap residue by cleaning your Hansgrohe product(s) when
needed.
• Select a cleaning agent specifically intended for the type of product.
• Do not use these types of cleaners as they will cause damage to your Hansgrohe product:
´ Any cleaning agent containing hydrochloric acid, formic acid, lye, or acetic acid.
´ Abrasive cleaning powders, pads, or brushes.
´ Steam cleaners.
´ “No rinse” cleaning agents.
• Always follow the instructions provided by the manufacturer of the cleaning agent.
• Do not mix cleaning agents, unless directed by the manufacturer.
• Do not spray cleaners directly onto the product as drops could enter openings and gaps and cause damage.
When using spray cleaners, spray the cleaner onto a soft cloth or sponge.
• Always rinse your Hansgrohe product thoroughly with clear water and polish dry with a soft cloth after
cleaning.
Important
• Residue from soaps and shampoos can cause damage. Rinse the product with clean water after each use.
• Residue from basin/tub/tile cleaner can cause damage to faucets and fittings. Immediately rinse any overspray
from the Hansgrohe product.
• Do not store any cleaning agents under your Hansgrohe product, such as in a vanity unit, as the fumes may
damage the product.
• Damage to the product caused by improper care or the use of improper cleaning agents is
not covered by the warranty.
• If a component of the product is damaged, replace it, as there is risk of injury.
Conseil de nettoyage pour les produits Hansgrohe
Les robinets pour les salles de bains et les cuisines modernes ainsi que les produits récents pour les douches se composent
de matériaux différents afin de satisfaire aux besoins du marché en termes de conception et de fonctionnalité. Afin
d’éviter d’endommager le produit, il est nécessaire d’en prendre soin.
Pour de meilleurs résultats :
• Empêchez l’accumulation de tarte et/ou de résidu de savon en nettoyant votre produit Hansgrohe lorsque c’est
nécessaire.
• Sélectionnez un produit de nettoyage spécifiquement prévu pour ce type de produit.
• N’utilisez pas ces types de nettoyants car ils peuvent endommager votre produit Hansgrohe :
´ Tout produit de nettoyage contenant de l’acide chlorhydrique, de l’acide formique, de la potasse ou de
l’acide acétique.
´ Les poudres de nettoyage, les tampons ou les brosses abrasives.
´ Les nettoyeurs à vapeur.
´ Les produits de nettoyage « sans rinçage ».
• Ne mélangez pas les produits de nettoyage, à moins que cela soit indiqué par le fabricant.
• Ne pulvérisez pas les nettoyants directement sur le produit car des gouttes pourraient entrer dans les
ouvertures et les fentes et causer des dommages. Lorsque vous utilisez des nettoyants par pulvérisation,
pulvérisez le nettoyant sur un chiffon ou une éponge douce.
• Après le nettoyage rincer abondamment à l’eau clair pour éliminer intégralement les restes de détergent.
Page is loading ...
20
Hansgrohe, Inc. 1490 Bluegrass Lakes Parkway Alpharetta, GA 30004
Tel. 800-334-0455 Fax 770-889-1783
www.hansgrohe-usa.com
US - Installation Instructions • Part No. 90694521• Revised 06/2019
This warranty is limited to products manufactured by Hansgrohe,
Inc. (“Hansgrohe”) that are purchased by a consumer in the United
States or Canada after March 1, 1996, and installed in either the
United States or in Canada.
WHO IS COVERED BY THE WARRANTY
This limited warranty extends to the original purchaser only. This
warranty is non-transferable. Hansgrohe neither assumes nor
authorizes any person to create for it any other obligation or liability
in connection with this product.
LENGTH OF WARRANTY
If you are a consumer who purchased the product for use primarily
for personal, family or household purposes, this limited warranty
starts on the date of purchase and extends for as long as you
own the product and the home in which the product is originally
installed. If you purchased the product for use primarily for any
other purpose, including, without limitation, a commercial purpose,
this limited warranty starts on the date of purchase and extends (i)
for 1 year, with respect to Hansgrohe and Commercial products,
and (ii) for 5 years, with respect to Axor products. The Rubbed
Bronze finish is subject to a 3-year limited warranty starting on
the date of purchase.
WHAT IS COVERED BY THE WARRANTY
This limited warranty covers only your Hansgrohe manufactured
product. Hansgrohe warrants this product against defects in
material or workmanship as follows:
Hansgrohe will replace at no charge for parts only or,
at its option, replace any product or part of the product
that proves defective because of improper workmanship
and/or material, under normal installation, use, service
and maintenance. If Hansgrohe is unable to provide a
replacement and repair is not practical or cannot be
made in timely fashion, Hansgrohe may elect to refund
the purchase price in exchange for the return of the
product. REPAIR OR REPLACEMENT (OR, IN LIMITED
CIRCUMSTANCES, REFUND OF THE PURCHASE PRICE)
AS PROVIDED UNDER THIS LIMITED WARRANTY IS THE
EXCLUSIVE REMEDY OF THE PURCHASER.
WHAT IS NOT COVERED BY THE WARRANTY
A. Conditions, malfunctions or damage not resulting from
defects in material or workmanship.
B. Conditions, malfunctions or damage resulting from (1)
normal wear and tear, improper installation, improper
maintenance, misuse, abuse, negligence, accident or
alteration; (2) the use of abrasive or caustic cleaning agents
or “no-rinse” cleaning products, or the use of the product
in any manner contrary to the product instructions; or (3)
conditions in the home such as excessive water pressure
or corrosion.
C. Labor and other expenses for disconnection, deinstallation,
or return of the product for warranty service (including but
not limited to proper packaging and shipping costs), or for
installation or reinstallation of the product.
D. Accessories, connected materials and products, or related
products not manufactured by Hansgrohe.
E. Any Hansgrohe or Axor product sold for display purposes.
HANSGROHE SHALL NOT BE LIABLE TO PURCHASER OR
ANY OTHER PERSON FOR ANY INCIDENTAL, SPECIAL
OR CONSEQUENTIAL DAMAGES, ARISING OUT OF
BREACH OF THIS LIMITED WARRANTY.
Some provinces and some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
TO OBTAIN WARRANTY PARTS OR INFORMATION
Contact your Hansgrohe retailer, or contact Technical Service at:
Hansgrohe, Inc.
1492 Bluegrass Lakes Parkway
Alpharetta, GA 30004
Toll-free 800-334-0455
In requesting warranty service, you will need to provide:
1. The sales receipt or other evidence of the date and place
of purchase.
2. A description of the problem.
3. Delivery of the product or the defective part, postage
prepaid and carefully packed and insured, to:
Hansgrohe, Inc.
1492 Bluegrass Lakes Parkway
Alpharetta, GA 30004
Toll-free 800-334-0455
When warranty service is completed, any repaired or replacement
product or part will be returned to you postage prepaid. REVISED
MAY 1, 2016.
PRODUCT INSTRUCTIONS AND QUESTIONS
Upon purchase or prior to installation, please carefully inspect
your Hansgrohe product for any damage or visible defect. Prior
to installing, always carefully study the enclosed instructions on the
proper installation and the care and maintenance of this product.
If you have questions at any time about the use, installation or
performance of your Hansgrohe product, or this warranty, please
write us or call us toll-free at 800-334-0455.
Limited Consumer Warranty
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Hansgrohe 04774670 Installation guide
- Category
- Faucets
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Hansgrohe 04774670 Guide d'installation
- español: Hansgrohe 04774670 Guía de instalación
Related papers
-
Hansgrohe 14113001 Installation guide
-
Hansgrohe 71130001 Installation guide
-
-
-
-
-
-
-
-
Other documents
-
Axor 39020001 Citterio Assembly Instruction
-
-
-
-
Axor 11041001 Urquiola Assembly Instruction
-
Axor 16582001 Montreux Installation guide
-
-
Axor 38020001 Uno Installation guide
-
-