Shop Vac SS11 Serie User manual

Brand: Shop Vac

Model: SS11 Serie

Category: Vacuum cleaners

Type: User manual

User manual

Please review before operating vac.

Manual del usuario

Por favor lea esta manual antes de usar la aspiradora.

Series

SS11, SS14, SS16

Wet/Dry Vacuum

Household and Workshop Use

Series

SS11, SS14, SS16

Aspiradora para aspiración de residuos

Líquidos/Sólidos

Para Uso Doméstico y Comercial

ATTENTION!

Read all safety rules carefully

before attempting to operate.

Retain for future reference.

ATENCIÓN!

Lea cuidadosamente todas

las normas de seguridad

antes de utilizar la aspira-

dora. Conserve esta man-

ual para consultas futuras.

PELIGRO!

Nunca opere esta unidad ante

la presencia de materiales o

vapores inflamables dado que

los artefactos eléctricos pro-

ducen arcos o chispas que

pueden causar un incendio o

una explosión.

NO DEJE LA ASPI-

RADORA FUNCIO-

NANDO SIN VIGI-

LANCIA!

DANGER!

Never operate this unit when

flammable materials or vapors

are present because electri-

cal devices produce arcs or

sparks that can cause a fire

or explosion.

NEVER OPERATE

UNATTENDED!

SHOP-VAC CORPORATION

2323 Reach Road, P.O. Box 3307

Williamsport, PA 17701-0307

(570) 326-3557

www.shopvac.com

SHOP-VAC CANADA

1770 Appleby Line

Burlington, Ontario L7L 5P8

(905) 335-9730

www.shopvac.ca

Shop Vac-México, S.A. de C.V.

Av. Mariano Otero #5095, Local 1 PB

Col. La Calma

Zapopan, Jalisco C.P. 45070

MÉXICO

52 (33) 3188 6388

Patents Issued and Pending.

Brevets délivrés et en instance.

Patentes registradas y en trámite.

Manuel d’utilisation

Veuillez lire avant d’utiliser l’aspirateur.

Séries

SS11, SS14, SS16

Aspirateur pour déchets secs et humides

Pour utilisation domestique ou dans les entrepôts

ATTENTION!

Lisez attentivement les in-

structions sur la sécurité

avant d’utiliser cet appareil.

Conservez ce manuel pour

vous y reporter ultérieurement.

DANGER

N’utilisez jamais cet aspira-

teur en présence de vapeurs

ou de matières inflammables.

Les appareils électriques

produisent des arcs ou des

étincelles qui peuvent causer

un incendie ou une explosion.

NE JAMAIS FAIRE

FONCTIONNER SANS

SURVEILLANCE!

BRAND/MARQUE/MARCA

in sketches B and C may be used

to connect this plug to a 2-pole

receptacle as shown in sketch B

if a properly grounded outlet is not

available. The temporary adaptor

should be used only until a properly

grounded outlet (sketch A) can be

installed by a qualified electrician.

The green colored rigid ear, lug or

the like extending from the adaptor

must be connected to a permanent

ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be

held in place by a metal screw.

IN CANADA, THE USE OF A TEMPORARY ADAPTOR IS NOT PERMITTED BY THE CANADIAN

ELECTRICAL CODE. Make sure that the appliance is connected to an outlet having the same

configuration as the plug. No adapter should be used with this appliance.

This appliance must be grounded. If it should malfunction or breakdown, grounding provides a

path of least resistance for electric current to reduce the risk of electric shock. This appliance

is equipped with a cord having an equipment-grounding conductor and grounding plug. The

plug must be inserted into an appropriate outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

WARNING – IMPROPER CONNECTION OF THE

EQUIPMENT-GROUNDING CONDUCTOR CAN RESULT IN A RISK OF

ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE

PERSON IF YOU ARE IN DOUBT AS TO WHETHER THE OUTLET IS

PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE

APPLIANCE – IF IT WILL NOT FIT THE OUTLET, HAVE A PROPER OUTLET

INSTALLED BY A QUALIFIED ELECTRICIAN.

This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks

like the plug illustrated in sketch A. A temporary adaptor that looks like the adaptor illustrated

GROUNDING INSTRUCTIONS

UNPACKING AND SET-UP

1. Pull lid latches in an outward motion, remove tank cover

and any accessories that may have been shipped in the

tank.

2. Attach caster system following the instructions and

illustrations in this manual.

3. Attach side tank handles following the instructions and

illustrations in this manual.

4. Before replacing tank cover, please refer to Dry Pick Up or

Wet Pick Up Operation in this manual to ensure you have

the proper filters installed for your cleaning operation.

5. Replace tank cover, and apply pressure with thumb to each latch until it snaps tightly in

place. Make sure all lid latches are clamped securely.

6. Insert machine hose end into inlet of tank. Twist slightly to tighten the connection (Figure

A). Friction Fit Inlet.

7. Insert machine hose end with locking-nut into inlet on the front of the tank. Turn locking

nut to tighten. Do not over-tighten (Figure B) Lock-On

inlet.

When using the appliance at a distance where an extension cord becomes necessary, a 3-conductor

grounding cord of adequate size must be used for safety, and to prevent loss of power and

overheating. Use the table below to determine A.W.G. wire size required. To determine ampere rating

of your vacuum, refer to nameplate located on rear of motor cover. Before using appliance, inspect

power cord for loose or exposed wires and damaged insulation. Make any needed repairs or

replacements before using your appliance. Use only three-wire outdoor extension cords which have

three-prong grounding-type plugs and three-pole receptacles which accept the extension cord’s

plug. When vacuuming liquids, be sure the extension cord connection does not come in contact with

the liquid.

EXTENSION CORDS

When using an electrical appliance, basic precautions should always be followed, including the

following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR INJURY:

1. Do not leave appliance when plugged in. Unplug from outlet when not in use and before

servicing. Connect to a properly grounded outlet only. See Grounding Instructions.

2. Do not expose to rain – store indoors.

3. Do not allow to be used as a toy. Close attention is necessary when used by or near children.

4. Use only as described in this manual. Use only Manufacturer’s recommended attachments.

5. Do not use with damaged cord or plug. If appliance is not working as it should, has been

dropped, damaged, left outdoors or dropped into water, contact Shop-Vac Corporation for

assistance.

6. Do Not: pull or carry by cord, use cord as a handle, close a door on cord or pull cord around

sharp edges or corners. Do not run appliance over cord. Keep cord away from heated

surfaces.

7. Do not unplug by pulling on cord. To unplug, grasp the plug; not the cord.

8. Do not handle plug or appliance with wet hands.

9. Do not put any object into openings. Do not use with any openings blocked; keep free of dust,

lint, hair and anything that may reduce air flow.

10. Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.

11. Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.

12. Do not use without dust bag and/or filters in place.

13. Turn off all controls before unplugging.

14. Use extra care when cleaning on stairs.

15. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where

they may be present.

16. Do not use your cleaner as a sprayer of flammable liquids such as oil base paints, lacquers,

household cleaners, etc.

17. Do not vacuum toxic, carcinogenic, combustible or other hazardous materials such as

asbestos, arsenic, barium, beryllium, lead, pesticides or other health endangering materials.

Specially designed units are available for these purposes.

18. Do not pick up soot, cement, plaster or drywall dust without cartridge filter and collection

filter bag in place. These are very fine particles that may pass through the foam and affect the

performance of the motor or be exhausted back into the air. Additional collection filter bags are

available.

19. Do not leave the cord lying on the floor once you have finished the cleaning job. It can become

a tripping hazard.

20. Use special care when emptying heavily loaded tanks.

21. To avoid spontaneous combustion, empty tank after each use.

22. The operation of a utility vac can result in foreign objects being blown into eyes, which can

result in eye damage. Always wear safety goggles when operating vacuum.

23. STAY ALERT. Watch what you are doing and use common sense. Do not use vacuum cleaner

when you are tired, distracted or under the influence of drugs, alcohol or medication causing

diminished control.

24. WARNING! Do NOT use this vacuum cleaner to vacuum lead paint debris because this may

disperse fine lead particles into the air. This vacuum cleaner is not intended for use under EPA

Regulation 40 CFR Part 745 for lead paint material cleanup.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

WARNING

– DO NOT LEAVE VACUUM UNATTENDED WHEN IT IS PLUGGED IN AND/OR OPERATING. UNPLUG UNIT WHEN NOT IN USE.

Volts

Total length of cord in feet

120V

Ampere Rating

More Not More

Than Than

0 - 6

6 - 10

10 - 12

12 - 16

25 50 100

150

AWG

Not recommended

8. Attach the extension wands to the accessory end of the

hose. Twist slightly to tighten the connection (Figure 1).

9. Attach one of the cleaning accessories (depending on

your cleaning requirements) to the extension wands. Twist

slightly to tighten the connection (Figure 1).

10. Plug the cord into the wall outlet. Your cleaner is ready for

use.

I = ON, O =OFF

NOTE: MANY MORE USEFUL TOOLS ARE AVAILABLE AT YOUR

LOCAL DEALER OR SHOP-VAC

WEBSITE.

NOTE: STATIC SHOCKS ARE COMMON

IN DRY AREAS OR WHEN THE RELATIVE

HUMIDITY OF THE AIR IS LOW. THIS

IS ONLY TEMPORARY AND DOES NOT

AFFECT THE USE OF THE APPLIANCE.

TO REDUCE THE FREQUENCY OF STATIC

SHOCKS IN YOUR HOME, THE BEST

REMEDY IS TO ADD MOISTURE TO THE

AIR WITH A CONSOLE OR INSTALLED

HUMIDIFIER.

With Wheel Dolly

You will find two casters (a), two large rear wheels (b), one axle (c), tool rack (d), two washers

(e), and two hair pin clips (f). If your vacuum is 16 U.S. gallons (60.5 liters) or larger you will

also find two screws, two metal flat washers and two square nuts with your wet/dry vacuum.

Assemble as follows:

1. Make sure the cord is disconnected from the receptacle then remove the tank cover.

2. If your unit is 4 U.S. gallon (15.1 liter) to 14 U.S. gallon (53 liter), assemble as follows:

a. Turn tank upside down so the bottom is facing up.

b. Continue on to step 4 below.

3. If your unit is 16 U.S. gallon (60.5 liter) or above, assemble as follows:

a. With the tank upright and back facing you, insert square nut into one of the two slots

located in back of dolly (Figure 11).

b. Place metal flat washer over stem of screw.

c. Tilt the tank forward slightly and locate the hole provided in the underside of the dolly

directly below the slot containing the square nut (Figure 12).

d. Place the screw, containing the flat washer, into the hole and turn clockwise until

end of screw is connected to square nut. If you have difficulty getting the screw to

connect to the square nut, push downward on the square nut with the eraser end of a

pencil while turning the screw.

e. Finish tightening the screw using 7/16” socket, wrench or nut driver.

f. Repeat steps a to e with the second slot in dolly.

g. Turn tank upside down so bottom is facing up. Continue on to set 4 below.

4. Place one hair pin clip in one end of axle (Figure 13). Slide one washer down the length of

the axle to rest on the hair pin clip. Slide wheel onto axle next to washer (Figure 14). Be

sure flat side of wheel hub is facing outward.

5. Slide axle through holes provided in tool rack (Figure 15).

6. Slide remaining wheel then washer onto axle. Insert hair pin clip into remaining hole in

axle to hold wheel in place (Figure 16).

7. Install tool rack assembly onto dolly (already installed on tank) by placing large slot in

tool rack over rim on back of dolly (Figure 17). Push tool rack onto dolly until the bottom

of tool rack is flush with bottom of dolly. NOTE: It is normal for tool rack to fit tightly onto

dolly.

8. Secure with four screws provided (Figure 18).

9. If plastic flat washers are included in hardware package, place one flat washer over stem

of each caster. NOTE: Flat washers are not required with all units.

10. Insert casters into front of dolly by placing stem of casters into holes provided. Apply

pressure and twisting motion until casters snap into place (Figure 19).

11. Return tank to upright position.

Not all units are equipped with the same caster system. Follow the instructions, which

apply to your specific unit.

With Caster Feet

1. With cord disconnected

from receptacle and tank

cover removed, turn tank

upside down so that the

bottom is facing up.

2. With a pair of scissors,

trim the enclosed template

to ﬁt your size tank. Sizes

will be 11”, 14” or 16”

diameters.

3. Once template is cut

out, place on bottom of

tank. Align inlet arrow on

template with center of

inlet on tank (Figure 2).

4. If caster feet are attached

together, separate by

removing webbing.

5. Take caster foot marked

with the letter A and align

arrow on foot (Figure 3)

with arrow on template

also marked with the letter

A (Figure 4).

6. Place groove of foot over

rim of tank and push until

the caster foot is tight

against bottom of tank

(Figure 5).

7. Secure feet with screw and washer when provided (Figure 6).

8. Repeat steps 4-7 with remaining feet.

9. If plastic ﬂat washers are included in hardware package, place one ﬂat washer over stem

of each caster. NOTE: Flat washers are not required with all units.

10. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and

twisting motion until casters snap into place (Figure 7).

11. Return tank to upright position.

CASTER SYSTEM ASSEMBLY

With Caster Dolly

You will ﬁnd four casters (a) with your wet/dry vacuum. If your vacuum is 16 U.S. gallon (60.5

liter) or larger, you will also ﬁnd two screws, two metal ﬂat washers and two square nuts.

Assemble as follows:

1. Make sure the cord is disconnected from the receptacle then remove the tank cover.

2. If your unit is 4 U.S. gallon (15.1 liter) to 14 U.S. gallon (53 liter), assemble as follows:

a. Turn tank upside down so the bottom is facing up.

b. Insert casters into bottom of dolly by placing stem of caster into holes provided. Apply

pressure and twisting motion until casters snap into place (Figure 8).

c. Return tank to upright position.

3. If your unit is 16 U.S. gallon (60.5 liter) or above, assemble as follows:

a. With the tank upright and back facing you, insert square nut into one of the two slots

located in back of dolly (Figure 9).

b. Place metal ﬂat washer over stem of screw.

c. Tilt the tank forward slightly and locate the hole provided in the underside of the dolly

directly below the slot containing the square nut (Figure 10).

d. Place the screw, containing the ﬂat washer, into the hole and turn clockwise until end of

screw is connected to square nut. If you have difﬁculty getting the screw to connect to

the square nut, push downward on the square nut with the eraser end of a pencil while

turning the screw.

e. Finish tightening the screw using 7/16” socket, wrench or nut driver.

f. Repeat steps a to e with the second slot in dolly.

Arrow

Template

Bottom of Tank

Tank Bottom

8 10

b c

12 13

15 16

18 19

(Not standard with all models)

Attach side handles to tank with screws provided (Figure 30).

(Not standard with all models)

NOTE: If foam sleeve is in postion over lid cage, it must be removed before installing cartridge

filter.

The cartridge filter can be used for wet or dry pick up; installation is the same for both. When

picking up large quantities of liquid please refer to the Wet Pick Up Operation section in this

manual. Use the cartridge filter in position over the lid cage for most general dry material pick

up. With the tank cover in an upside down position, slide the cartridge filter down over the

lid cage, pushing until the filter seals against the cover (Figure 36). Place filter retainer into

the top of the cartridge filter, hold the tank cover with one hand, turn the handle on the filter

retainer clockwise to tighten, locking the filter into place (Figures 37 & 38). To remove the

filter for cleaning, again hold the tank cover and turn the filter retainer counter-clockwise to

loosen and remove, slide the cartridge filter off the lid cage (Figures 39 & 40). To clean the

cartridge filter shake or brush off excess dirt or rinse (from the inside of the filter) with water,

dry completely (approximately 24 hours) and reinstall (Figures 41 & 42). NOTE: If the filter

has been used for wet pick up, it must be cleaned and dried before using for dry pick up.

INSTALLING THE CARTRIDGE FILTER

WARNING – ALWAYS DISCONNECT THE PLUG FROM THE

WALL OUTLET BEFORE REMOVING THE TANK COVER.

When using the reusable dry filter

to pick up dust and dry material,

you must install foam sleeve

and reusable dry filter to ensure

proper filtration. If the vacuum

has been used to pick up liquids,

the foam sleeve must be cleaned

and dried before installing for dry

pick up. With tank cover in an

upside down position, slide foam

sleeve down over lid cage pulling

until foam sleeve completely

covers lid cage (Figures 31, 32).

Center the reusable dry filter on lid

cage (Figure 33), slide mounting

ring down over filter until ring is

positioned against the ribs of the lid

cage (Figure 34). The reusable dry

filter should always be in position over the foam sleeve for dry pick

up. To remove the filter for cleaning, remove mounting ring and filter

from lid cage (Figure 35). To clean the reusable dry filter, shake

off excess dirt and dust or (depending on the condition of the filter)

rinse with water. Allow the filter to dry completely and reinstall.

DO NOT MACHINE WASH OR DRY.

(Not standard with all models)

INSTALLING FOAM SLEEVE AND

REUSABLE DRY FILTER

DRY PICK UP

INSTALLING THE CARRIAGE HANDLE

(Not standard with all models)

Follow the instructions for the carriage handle that came with your vacuum.

If your side tank handles look like the ones pictured to the right,

follow these instructions (Figure 23).

You will ﬁnd one carriage handle and a handle pack containing two side tank handles, four

handle supports and eight screws. Assemble as follows:

1. Take two handle supports and two 1” screws. Place screws

through the hole provided in center of each support

(Figure 24).

2. Position the tank, in the upright position, with the inlet facing

you. Put the support assemblies inside the tank, then place

the screws through the holes provided on left side of the tank.

Make sure the plastic portion is located inside the tank. Turn

the supports until the back of the supports ﬁt ﬂush against the

inside curve of the tank (Figure 25).

3. Remove any webbing that attaches the tank handles to each

other. Take the side tank handle with the letter L and position

it on the outside of the tank where the support assemblies

are installed. The U-shaped cutout on the bottom end of the

handle must face the rear of the tank. Secure the side tank

handle to the tank with the screws in the support assemblies

(Figure 26).

4. Repeat steps 1 to 3 using right side of tank and the remaining side tank handle marked with

the letter R.

5. Position metal carriage handle outside of tank and under

the tank handles. Be sure to spread ends of carriage handle

when assembling to prevent damage to tank. Line up holes in

ends of carriage handle with holes in bottom of tank handles.

Make sure carriage handle is in the U-shaped cut on the tank

handles (located towards rear of unit). Secure with 1½” screws

provided (Figure 27).

If your side tank handles look like the ones pictured to the right,

follow these instructions (Figure 28).

21 22

TOOL HOLDER

(Not standard with all models)

1. With rear of unit facing you, take tool holder and position it with tabs facing rear of unit

(Figure 20).

2. Place "J" shaped tabs into the slots on cord wraps (Figure 21).

3. Press down until tabs snap into place.

4. Press down on center of tool holder until tab latches on bottom of lid (Figure 22).

6. Attach carriage handle to tank by inserting bolt through the center hole of handle and tank,

secure with nut provided. Attach side handles with screws provided. Be sure to spread ends

of carriage handle when assembling to prevent damage to tank (Figure 29).

Item Description

1 Metal tank handle

2 Side tank handle

3 #10 x 3/4” Screw hex head

4 Bolt 1/4 - 20 x 1/2”

5 1/4 - 20 Hex nut

SIDE TANK HANDLE ASSEMBLY

EMPTYING LIQUID WASTES FROM THE TANK

Not all units are equipped with tank drains. Follow the instructions, which apply to

your specific unit.

Without Tank Drain

Liquid waste may be emptied by removing the tank cover. To empty, stop the motor and

remove the plug from the wall receptacle. Remove the tank cover and deposit the liquid

waste contents in a suitable drain. After tank is empty, return the cover to its original

position. To continue use, plug the cord into the wall receptacle and turn the unit on.

With Tank Drain

Liquid waste may be emptied by removing the tank drain. To empty, turn unit off and remove

plug from wall receptacle. Remove the drain cap and deposit the liquid waste contents in

a suitable drain. After the tank is empty, return the drain cap to its original position. To

continue use, plug the cord into the wall receptacle and turn the unit on.

Your vacuum can be used as a powerful blower. To use your unit

as a blower, clear hose of any obstruction. Insert machine hose

end into blower port on rear of unit (Figure 48). Twist slightly

to tighten the connection. Caution should be used when using

as a blower due to the powerful force of air when using certain

attachments.

WARNING – ALWAYS WEAR EYE PROTECTION TO

PREVENT ROCKS OR DEBRIS FROM BEING BLOWN OR RICOCHETING

INTO THE EYES OR FACE, WHICH CAN RESULT IN SERIOUS INJURY.

BLOWER FEATURE

WET PICK UP OPERATION

Remove ALL dirt and debris found in the tank. The vacuum requires only a minimum of

conversion when going from dry to wet pick up. Remove all dry use filters from the vacuum.

A clean cartridge filter may be used for vacuuming small amounts of liquids. For proper

installation of the cartridge filter refer to Installing the Cartridge Filter. For best results when

vacuuming large quantities of liquid, remove the cartridge filter. When vacuuming liquids

containing debris, it is recommended purchasing a foam sleeve and install over filter cage;

otherwise a foam sleeve is not required for wet pick up. Foam sleeve and additional filters may

be purchased by visiting our website at www. shopvac.com, contacting our customer service

department, or purchasing at your local Shop-Vac

distributor.

Misting in exhaust air may occur if the filter becomes saturated during wet pick up. If misting

occurs, remove filter and allow to dry or, replace with another dry filter to eliminate the misting

and possible dripping of liquid around the lid. Turn the unit off immediately upon completing

a wet pick-up job or when tank is full and ready to be emptied. Raise the hose to drain any

excess liquid into the tank. The interior of the tank should be periodically cleaned.

The foam sleeve should be cleaned periodically as described in the following steps:

1. Always disconnect the plug from the wall receptacle before removing the tank cover. Place

tank cover in an upside down position. Remove foam sleeve by sliding it up and off the lid

cage.

2. Shake excess dust off foam sleeve with a rapid up and down movement.

3. Hold foam sleeve under running water for a minute or two, rinsing from the inside. A water

wash is not always required, depending on the condition of the foam sleeve.

4. Gently wring out excess water, blot foam sleeve with a clean towel, and allow to dry. The

foam sleeve is now ready to be reinstalled on the lid cage.

NOTE: WET PICK UP ACCESSORIES SHOULD BE WASHED PERIODICALLY, ESPECIALLY AFTER

PICKING UP WET, STICKY KITCHEN ACCIDENTS. THIS CAN BE ACCOMPLISHED WITH A WARM

SOLUTION OF SOAP AND WATER.

WARNING FOR FINE DUST & POWDERS

When vacuuming fine dust, or powders of any kind (ex. plaster, drywall dust, cold ashes,

concrete dust, etc.)...a high efficiency drywall filter bag must be used. When vacuuming

normal household dust and debris, standard household disposable filter bags may be used.

These "large bag" filters connect to the air inlet fitting on the inside of the vacuum tank.

FILTER SELECTION GUIDE

SIZE

5-8 U.S. Gal (18.9-30.3L)

10-14 U.S. Gal (37.8-53L)

15-22 U.S. Gal (56.8-83.2L)

5-10 U.S. Gal. (18,9-37,8L)

12-20 U.S. Gal. (18,9-37,8L)

90671/

90672/

90673/

90215/

90216/

90107/ REUSABLE DRY FILTER AND MOUNTING RING

fits most Shop-Vac

Wet/Dry Vacuums.

90585/ FOAM FILTER SLEEVE fits most Shop-Vac

Wet/Dry Vacuum

Fine dust

Drywall

Standard

Household

90661/

90662/

90663/

INSTALLING THE DISPOSABLE FILTER BAG

(Not standard with all models)

1. Use the disposable ﬁlter bag in conjunction with the cartridge ﬁlter for easy disposal of the

debris. The bag is not required for normal dry pick up. When picking up ﬁne dust or powders

a high efﬁciency ﬁlter bag (not standard with all models) must be used.

NOTE: Use for dry pick up only.

2. With cord disconnected from the receptacle, pull latches in an outward motion and remove

the tank cover.

3. Unscrew hose locking-nut and remove hose from inlet (Figure 43).

4. Remove the inlet deﬂector from the deﬂector guide. NOTE: Hose must be removed before

the inlet deﬂector can be taken out (Figure 44).

5. Position the inlet deﬂector with the opening facing the left or the right side of the ﬁlter bag.

Slide the ﬁlter bag collar over the inlet deﬂector, matching the notches of the bag collar to

the tabs on the inlet deﬂector. Bag will only ﬁt properly one way (Figure 45).

6. Slide the inlet deﬂector with the ﬁlter bag attached into the deﬂector guide (Figure 46).

7. Reinsert hose into inlet and tighten the locking-nut (Figure 47).

8. When secured in place, expand the ﬁlter bag and position around the inside of the tank.

Replace tank cover.

NOTE: When removing ﬁlter bag from tank, remove the inlet deﬂector from the ﬁlter bag

collar. Reinstall inlet deﬂector into deﬂector guide. Inlet deﬂector must be in place for any

type of cleaning.

9. When secured in place, expand the ﬁlter bag and position around the inside of the tank

Replace tank cover.

TEAR RESISTANT WET / DRY COLLECTION BAG

The tear resistant wet / dry collection bag can be used in conjunction with the cartridge ﬁlter

for picking up dry debris. The bag is not required for dry pick up; however, it makes it easier

to remove the debris and keeps the tank clean. When picking up ﬁne dust or powders a high

efﬁciency bag must be used. The high efﬁciency bags are for dry use only and do not come

standard with this model.

The tear resistant wet / dry collection bag can also be used in conjunction with the foam

sleeve when picking up liquids or using the pump feature. The bag traps medium to large

debris that may be contained in the liquid, while allowing the liquid to ﬂow through the

bag and deposit into the vacuum’s tank. The bag is not required for wet pick up, but it is

recommended when the liquid contains debris that could damage the vacuum’s motor. NOTE:

If the bag is used for wet pick up, it must be removed from the tank and hung up to dry.

To install the bag:

1. With cord disconnected from the receptacle, pull latches in an outward motion and remove

the tank cover.

2. Unscrew hose locking-nut and remove hose from inlet (Figure 43).

3. Remove the inlet deﬂector from the deﬂector guide. NOTE: Hose must be removed before

the inlet deﬂector can be taken out (Figure 44).

4. Position the inlet deﬂector with the opening facing the left or the right side of the ﬁlter bag.

Slide the ﬁlter bag collar over the inlet deﬂector, matching the notches of the bag collar to

the tabs on the inlet deﬂector. Bag will only ﬁt properly one way (Figure 45).

5. Slide the inlet deﬂector with the ﬁlter bag attached into the deﬂector guide (Figure 46).

6. Reinsert hose into inlet and tighten the locking-nut (Figure 47).

7. When secured in place, expand the ﬁlter bag and position around the inside of the tank.

Replace tank cover.

NOTE: When removing ﬁlter bag from tank, remove the inlet deﬂector from the ﬁlter bag

collar. Reinstall inlet deﬂector into deﬂector guide. Inlet deﬂector must be in place for any

type of cleaning.

8. When secured in place, expand the ﬁlter bag and position around the inside of the tank

Replace tank cover.

To remove the bag:

1. If the bag was used for wet pick up, move the vacuum outside or to a ﬂoor that won’t get

damaged if the liquid drips onto it.

2. Make sure the cord is disconnected from the receptacle, the tank cover is removed and the

hose is disconnected from the tank inlet.

3. Grasp the plastic collar ﬁrmly and pull the rubber guard off of the inlet ﬁtting. Before

removing the bag from the tank, insert the plastic tab connected to the collar into the bag

opening.

4. If the bag was used for dry pick up, simply grasp the plastic handle and remove from the

tank.

5. If the bag was used for wet pick up, grasp the plastic handle and slowly lift up on the bag.

Allow the liquid to drain from the bag into the tank. If the bag is not full, hang it up and allow

it to dry completely. Once dry, check the bag for tears or holes. If none are found the bag can

be reinstalled.

NOTE: Additional collection bags are available at your local dealer or the Shop-Vac

website.

LUBRICATION

No lubrication is necessary as the motor is equipped with lifetime lubricated bearings.

Trouble Possible Cause Remedy

Suction weakens or

cleaner runs hot

Clogged filter

Brush dirt from filter. If condition continues,

change filter.

Air leak Check all fittings for tight fit (nozzles, hose, etc.)

Check that tank cover is sealed properly.

Obstruction in hose

or nozzle

Check nozzle, hose, etc. for obstructions, and

remove if present.

Misting in the

exhaust air

Saturated filter Replace saturated filter with a dry filter.

TROUBLESHOOTING

WARNING –

IF ANY OF THE MOTOR HOUSING PARTS

SHOULD BECOME DETACHED OR BROKEN, EXPOSING THE MOTOR

OR ANY OTHER ELECTRICAL COMPONENTS, OPERATION SHOULD BE

DISCONTINUED IMMEDIATELY TO AVOID PERSONAL INJURY OR FURTHER

DAMAGE TO THE VACUUM. REPAIRS SHOULD BE MADE BEFORE REUSING

THE VACUUM.

STORAGE

Before storing your vacuum cleaner the tank should be emptied

and cleaned. The power cord can be wrapped around the cord

wraps provided on the tank cover on rear of unit (Figure 49).

Accessories may be stored in the tool holder (not standard on all

models) so they can be readily available. The vacuum should be

stored indoors.

FIVE YEAR HOME USE WARRANTY

Your Shop-Vac® vacuum cleaner is warranted for normal household use, in accordance

with the User Manual, against original defects in material and workmanship for a period of

five years from date of purchase. Should this product be used for commercial or rental use,

a 90 day limited warranty will apply. Shop-Vac Corporation warrants placing this vacuum

cleaner in correct operating condition, by repair or parts replacement, during the warranty

period, without charge. This warranty does not cover accessories. Use of non-recommended

filters and/or accessories may void the manufacturer's warranty. Shop-Vac® assumes no

responsibility for damage or faulty performance caused by misuse, careless handling, and

where repairs or modifications have been made. Do not attempt to service your vacuum

beyond that described in the User Manual. Proof of purchase date is required. The warranty

gives you specific legal rights, and you may have other rights which vary from state to state

or province to province. This warranty is void outside of the United States and Canada.

Customers in the United States: for product service contact Shop-Vac Corporation, Customer

Service, at (570) 326-3557 or go to www.shopvac.com/support. Visit www.shopvac.com for

your vacuum's parts list schematic.

Customers in Canada: for product service return the complete unit, (transportation prepaid), to

the Authorized Shop-Vac® Service Centre nearest you. A complete list of Authorized Service

Centres is included with each vacuum cleaner.

Customers in Mexico: for product service see paperwork that came with your unit.

The vacuum is equipped with an automatic suction shut-off that operates when picking up

liquids. As the level of the liquid rises in the tank, an internal float rises until it seats itself

against a seal at the intake of the motor, shutting off suction. When this happens, the motor

will develop a higher than normal pitch noise and the suction is drastically reduced. If this

occurs, turn unit off immediately. Failure to turn unit off after float rises and shuts off suction

will result in extensive damage to the motor. To continue use, empty the liquid waste from

the tank as outlined in the previous paragraph.

NOTE: IF ACCIDENTALLY TIPPED OVER, THE VACUUM COULD LOSE SUCTION. IF THIS

OCCURS, PLACE VAC IN UPRIGHT POSITION AND TURN SWITCH OFF. THIS WILL ALLOW

THE FLOAT TO RETURN TO ITS NORMAL POSITION, AND YOU WILL BE ABLE TO CONTINUE

OPERATION.

AUTOMATIC SUCTION SHUT-OFF

Page is loading ...

Shop Vac SS11 Serie User manual

Brand: Shop Vac

Model: SS11 Serie

Category: Vacuum cleaners

Type: User manual

Download PDF

report

in other languages

français: Shop Vac SS11 Serie Manuel utilisateur
español: Shop Vac SS11 Serie Manual de usuario

Shop Vac SS11 Serie User manual

Shop Vac SS11 Serie User manual

in other languages

Related papers

Other documents