Bosch HGG24W256R/35 User manual

Category
Kitchen & houseware accessories
Type
User manual

This manual is also suitable for

[en] Instruction manual
Free standing cooker HGG24W226R, HGG24W256R
3
Ú Table of contents
[en]Instruction manual
Safety precautions .....................................................................4
Before installation ...............................................................................4
Safety information ...............................................................................4
Causes of damage .............................................................................5
Set-up, gas and electricity connection.....................................5
Gas connection ...................................................................................5
Faults in the gas installation/smell of gas .....................................6
Electrical connection ..........................................................................6
Levelling the cooker ...........................................................................6
Setting up the appliance ...................................................................6
Measures to be noted during transport..........................................6
Your new cooker.........................................................................7
General information ............................................................................7
Cooking area .......................................................................................7
Oven ......................................................................................................8
Accessories .........................................................................................8
Before using the oven for the first time ................................. 10
Setting the time of day.................................................................... 10
Heating up the oven........................................................................ 10
Setting procedure for the lower gas burner ............................... 10
How to set the gas grill................................................................... 10
Cleaning the accessories............................................................... 11
Advance cleaning of burner cup and cap .................................. 11
Making settings on the hob.....................................................11
Igniting the gas burners.................................................................. 11
Table - Cooking................................................................................ 11
Setting the oven........................................................................12
This is how you adjust the lower gas burner in the oven ........ 12
Setting procedure for the gas grill in the oven .......................... 12
Setting the timer .......................................................................13
Care and cleaning .................................................................... 13
Upper glass cover ........................................................................... 13
Cleaning agents............................................................................... 13
Detaching and refitting the rails.................................................... 14
Detaching and attaching the oven door...................................... 15
Removing and installing the door panels ................................... 15
Troubleshooting ....................................................................... 16
Malfunction table.............................................................................. 16
Replacing the bulb in the oven ceiling light ............................... 16
Glass cover....................................................................................... 16
After-sales service ................................................................... 16
E-number and FD-number.............................................................. 16
Energy and environment tips.................................................. 17
Saving energy................................................................................... 17
Saving energy with the gas hob ................................................... 17
Environmentally-friendly disposal.................................................. 17
Tested for you in our cooking studio. .................................... 17
Cakes and pastries ......................................................................... 17
Baking tips ........................................................................................ 18
Meat, poultry, fish, toast ................................................................. 18
Tips for roasting and grilling.......................................................... 19
Acrylamide in foodstuffs......................................................... 19
Produktinfo
Additional information on products, accessories, replacement
parts and services can be found at www.bosch-home.com and
in the online shop www.bosch-eshop.com
4
Safety precautions
Read this instruction manual carefully. Keep the instruction and
installation manuals, as well as the various accessories, in a
safe place. Please pass on these manuals and the accessories
to the new owner if you sell the appliance.
These instructions are only valid if the appropriate country
symbol appears on the appliance. If the symbol does not
appear on the appliance, it is necessary to refer to the
technical instructions which will provide the necessary
instructions concerning modification of the appliance to the
conditions of use of the particular country.
Appliance category: Category 1
Before installation
Damage during transport
Check the appliance for damage after unpacking it. Do not
connect the appliance if it has been damaged in transit.
Incorrect connection.
The appliance (electricity and gas connection) must be
installed in accordance with the instruction manual and the
instructions for gas connection and conversion to a different
gas type.
Incorrect connection and incorrect settings may cause serious
damage to the appliance. The appliance manufacturer does not
accept any liability for such damage. The appliance warranty
will be invalidated.
Safety information
Caution:This appliance is for cooking purposes only. It must
not be used for other purposes, for example room heating. This
hob must only be used for food preparation.
Adults and children who have any physical, motor or mental
impairment
and/or are not sufficiently informed about how to use the
appliance or not familiar with the appliance
must not operate the appliance without supervision.
Children must not be allowed to play with the appliance.
Hot surfaces
ã=Risk of burns!
Caution: Accessible parts may be hot when the grill is in
use. Young children should be kept away from the
appliance.
Never touch the interior oven surfaces, the hot burners and
heating elements. Keep small children away from the
appliance.
Never prepare food containing large quantities of drinks with
a high alcohol content. The alcoholic vapours may catch fire
in the oven. Only use small quantities of drinks with a high
alcohol content and open the oven door carefully.
Electricity/gas cables must not come into contact with the
back of the appliance. When the appliance is in operation,
the back of the appliance heats up. This may cause damage
to the power cables.
Never clean the appliance while it is hot. Allow the appliance
to cool down before cleaning it.
Open the oven door carefully. Hot steam may escape.
ã=Risk of fire!
Never place flammable objects on the burners or store them in
the cooking compartment. Never open the appliance door if
there is smoke inside. Switch off the appliance. Pull out the
mains plug or switch off the appliance at the circuit breaker in
the fuse box. Shut off the gas supply.
The surfaces of the plinth drawer may become very hot. Only
store oven accessories in the drawer. Flammable and
combustible objects must not be stored in the plinth drawer.
There is a risk of fire!
ã=Risk of short circuit!
Never trap the mains cable of electrical appliances in the
appliance door when it is hot or pull the cable over burners
when they are hot. The cable insulation could melt.
ã=Risk of scalding!
Never pour water into the hot cooking compartment. This will
produce hot steam.
Hot accessories and ovenware
ã=Risk of burns!
Never remove ovenware or accessories from the cooking
compartment without an oven cloth or oven gloves.
Overheated oil and fat
ã=Risk of fire!
Overheated oil or fat can ignite very quickly. Never leave hot oil
or fat unattended. Never attempt to extinguish burning fat or oil
with water. Extinguish the flames with a lid or a plate. Switch the
hotplate off.
Insufficient ventilation when cooking with gas cookers
Caution:The use of a gas cooking appliance results in the
production of heat, moisture and products of combustion in the
room in which it is installed. Ensure that the kitchen is well
ventilated especially when the appliance is in use: keep natural
ventilation holes open or install a mechanical ventilation device
(mechanical extractor hood).
Prolonged intensive use of the appliance may call for additional
ventilation, for example opening of a window, or more effective
ventilation, for example increasing the level of mechanical
ventilation where present.
Do not hang easily combustible materials, such as curtains,
near this appliance. If the burners are not covered with
ovenware, do not operate the extractor hood. Grease deposits
in the filters of the extractor hood may ignite, and the resulting
hot temperatures may damage the extractor hood. There is a
risk of fire!
Hinges
Do not place your hands in the oven door hinges or, if
available, the upper cover hinges. You could trap your fingers.
Repairs
Incorrect repairs may result in significant risk to the user. Risk
of electric shock. There is a risk of a gas leak!
Repairs may only be carried out by fully trained after-sales
service engineers. A damaged cable must only be replaced by
the after-sales service engineer.
Switch off the circuit breaker in the fuse box if the appliance is
faulty. Shut off the gas supply. Call the aftersales service.
Moving the appliance by the gas line or door handle
Do not move the appliance while holding the gas line; the gas
pipe could be damaged. There is a risk of a gas leak! Do not
move the appliance while holding it by the door handle. The
door hinges and door handle could be damaged.
5
Oven door - Additional safety precautions
During long cooking times, the oven door may become very
hot.
If you have small children, extra supervision is required during
oven operation.
In addition, there is a protective device (protective grid) which
prevents direct contact with the oven door. You can purchase
this optional accessory (469088) from the after-sales service.
Upper glass cover
Caution: The glass cover may crack due to heat. Before
closing the cover, turn off all burners. Wait until the oven has
cooled down before closing the glass cover.
Causes of damage
Hob
Caution!
Only use the burners when cookware has been placed on
top. Do not heat up empty pots or pans. The saucepan base
will be damaged.
Only use pots and pans with an even base.
Place the pot or pan centrally over the burner. This will
optimise transfer of the heat from the burner flame to the pot
or ban base. The handle does not become damaged, and
greater energy savings are guaranteed.
Ensure that the gas burners are clean and dry. The burner
cup and ¶burner cap must be positioned exactly.
Ensure that the top cover is not closed when the oven is
started up.
Damage to the oven
Caution!
Do not push baking trays onto the oven floor. Do not line the
oven floor with aluminium foil. Do not place any food
containers on the oven floor, as this could cause heat to
accumulate. The baking and roasting times will no longer be
correct and the enamel will be damaged.
Do not pour water directly into a hot oven. This could damage
the enamel.
Do not use too much fruit when baking a very liquid fruit
cake. Fruit juice, which drips from the baking tray, may cause
stains that cannot be removed.
Do not use the open oven door as a seat or footstool.
Damage to the plinth drawer
Caution!
Do not place hot objects in the plinth drawer. It could be
damaged.
Damage to the fronts of adjacent units
Caution!
Only allow the oven to cool down with the oven door closed.
Even if the door is only open slightly open, the fronts of
adjacent units could be damaged over time.
If the oven seal is very dirty, the oven door will not close
properly during operation. The fronts of adjacent units will
become damaged over time. Always keep the door seal
clean.
Set-up, gas and electricity connection
Gas connection
Installation must only be performed by an approved expert or a
licensed after-sales service engineer in accordance with the
instructions specified under "Gas connection and conversion to
a different gas type".
For the licensed expert or after-sales service
Caution!
The setting conditions for this appliance are specified on the
rating plate on the back of the appliance. The gas type set in
the factory is marked with an asterisk (*).
Before setting up the appliance, check the grid access
conditions (gas type and gas pressure) and ensure that the
gas setting of the appliance meets these conditions. If the
appliance settings have to be changed, follow the instructions
in the section "Gas connection and conversion to a different
gas type".
This appliance is not connected to a waste gas main. It must
be connected and commissioned in accordance with the
installation conditions. Do not connect the appliance to a
waste gas main. All ventilation regulations must be observed.
The gas connection must be made via a fixed, i.e. not mobile
connection (gas line) or via a safety hose.
If using the safety hose, ensure that the hose is not trapped
or crushed. The hose must not come into contact with hot
surfaces.
The gas line (gas pipe or safety hose) can be connected to
the right or left-hand side of the appliance. The connection
must have an easily accessible locking device.
Safety information
The nominal operating pressure of the appliance is;
For natural gas (G20) 20 mBar, for LPG (G30) 30 mBar, for
LPG (G31) 37 mBar. The appliance must be operated at these
pressure values. All data on the rating plate of your appliance
relates to these pressure values. The manufacturer is not
responsible for results, performance or any risk caused by
operating the appliance at different values.
6
ã=If the gas pressure in your gas supply grid!
for natural gas (G20) is higher than 25 mBar, for LPG (G30) is
higher than 36 mBar, for LPG (G31) is higher than 45 mBar,
you must use your appliance in connection with a suitable gas
regulator, for safety reasons. Connection, maintenance and
configuration of the gas regulator must be performed by an
authorised installation expert. If you do not know the gas
pressure in your gas supply grid, please ask your local supply
grid operator.
Faults in the gas installation/smell of gas
If you notice a smell of gas or faults in the gas installation, you
must
immediately shut off the gas supply and/or close the gas
cylinder valve
immediately extinguish all naked flames and cigarettes
switch off electrical appliances and lights
open windows and ventilate the room
call the aftersales service or the gas supplier
Electrical connection
Caution!
Have the appliance set up by your after-sales service. A 16 A
fuse is required for connection. The appliance is designed for
operation at 220-240 V.
If the electricity supply drops below 180 V, the electrical
ignition system does not work.
Any damage arising from the appliance being connected
incorrectly will invalidate the guarantee.
For the after-sales service
Caution!
The appliance must be connected in accordance with the
data on the rating plate.
Only connect the appliance to an electrical connection that
meets the applicable provisions. The socket must be easily
accessible so that you can disconnect the appliance from the
electricity supply if necessary.
Please ensure the availability of a multi-pin disconnecting
system.
Never use extension cables or multiple plugs.
For safety reasons, this appliance must only be connected to
an earthed connection. If the safety earth terminal does not
comply with regulations, safety against electrical hazards is
not guaranteed.
You must use a H 05 W-F type cable or equivalent for the
appliance connection.
Levelling the cooker
Always place the cooker directly on the floor.
1.Pull out the plinth drawer and lift it up and out.
There are adjustable feet at the front and rear on the inside of
the plinth.
2.Use an Allen key to raise or lower the adjustable feet as
necessary until the cooker is level (picture A).
3.Push the plinth drawer back in (picture B).
Setting up the appliance
The appliance must be set up directly on the kitchen floor
and in line with the specified dimensions. The appliance must
not be set up on any other object.
The distance between the top edge of the oven and the
bottom edge of the extractor hood must meet the
requirements of the extractor hood manufacturer.
Ensure that the appliance is not moved again after set up.
The distance from the high output burner or wok burner to
the fronts of the adjacent units or the wall must be at least 50
mm.
Measures to be noted during transport
Secure all mobile parts in and on the appliance using an
adhesive tape that can be removed without leaving any traces.
Push all accessories (e.g. baking tray) into the corresponding
slots with cardboard at the edges, in order to avoid damaging
the appliance. Place cardboard or similar between the front and
rear side to prevent knocks against the inside of the glass door.
Secure the door and, if available, the top cover to the appliance
sides using adhesive tape.
Keep the original appliance packaging. Only transport the
appliance in the original packaging. Observe the transport
arrows on the packaging.
If the original packaging is no longer available
pack the appliance in protective packaging to guarantee
sufficient protection against any transport damage.
Transport the appliance in an upright position. Do not hold the
appliance by the door handle or the connections on the rear, as
these could be damaged. Do not place any heavy objects on
the appliance.
%$


0LQ

7
Your new cooker
Here you will learn about your new cooker. We will explain the
control panel, the hob and the individual operating controls.
You will find information on the cooking compartment and the
accessories.
General information
The design depends on the respective appliance model.
Cooking area
Only use pots or pans with an even base.
Place the pot or pan centrally over the burner. This will optimise
transfer of the heat from the burner flame to the pot or ban
base. The handle does not become damaged, and greater
energy savings are guaranteed.
&DXWLRQ
'XULQJRSHUDWLRQ
RIWKHRYHQKRW
VWHDPHPHUJHV
DWWKLVSRLQW
6WHDPRXWOHW
)URQWSDQHO
3OLQWKGUDZHU
&RQWUROSDQHO
0XVWEH
RSHQZKHQ
WKHDSSOLDQFH
LVLQRSHUDWLRQ
+REFRYHU
+RWSODWHV
2YHQGRRU
6WHDPRXWOHW
&DXWLRQ+RWDLU
LVUHOHDVHGKHUH
6WDQGDUG
EXUQHU
(FRQRP\
EXUQHU
6WDQGDUG
EXUQHU
:RNEXUQHU
Hob Pot or pan diameter
Economy burner 1kW 1218 cm
Standard hob 1.7 kW 1824 cm
Wok burner 3.6 kW 2428 cm
8
Burner knob
You can adjust the heat setting of the hotplates using the four
burner knobs.
There is a limit stop at the end of the settings area. Do not turn
the timer beyond this.
Ignition button
This button activates the electronic ignition system.
When you press the button, all igniters ignite at the same time.
Oven
Function selector
Turn the function selector anti-clockwise to set the oven
temperature or clockwise to select the grill.
Heat setting for the lower burner: 3 kW
Heat setting of the gas grill: 2,1 kW
Light button
This button switches on the oven light.
To switch it off, press the multi-function button again.
Buttons and display
The buttons are used to select the various additional functions.
In the display, you can read the values that you have set.
Accessories
The accessories can be inserted in the oven at 5 different
levels.
You can pull out the accessories two-thirds of the way out
without them tilting. This allows meals to be taken out easily.
Heat may cause the accessories to deform. As soon as the
accessories cool down, they regain their original shape. Their
function is not impaired.
Hold the baking tray securely on the sides with both hands and
push it parallel into the frame. Avoid movements to the right or
left when pushing the baking tray in. Otherwise, it will be difficult
to push the tray in and the enamelled surfaces could be
damaged.
You can buy accessories from the after-sales service, from
specialist retailers or online. Please specify the HEZ number.
The Positions Function/gas oven
þ
Zero position The oven is switched off.
˜
Settings area Large flame = highest setting
Economy flame = lowest setting
Positions Function
ÿ
Zero position Oven not hot.
170-270 Temperature
range
Temperature range in ºC for
baking cakes in baking tins,
pizza on the baking sheet, bis-
cuits etc.
(
Grill setting Grill burner setting for grilling
at maximum temperature.
Button Function
0
Clock button Use this button to set the timer
and the
x cooking time.
A
Minus button Use this button to adjust the set
value downwards.
@
Plus button Use this button to adjust the set
value upwards.
Wire rack
For ovenware, cake tins, roasts,
grilling and frozen meals.
Push the wire rack in with the elbow
pointing downwards
¾.
Enamel baking tray
For cakes and biscuits.
Slide the baking tray into the oven
with the sloping edge facing
towards the oven door.
Aluminium baking tray
For cakes and biscuits.
Slide the baking tray into the oven
with the sloping edge facing
towards the oven door.
Protective plate
For use when grilling.
When grilling, always use the pro-
tective plate to protect the control
panel and control knobs from high
temperatures.
9
Optional accessories
You can buy optional accessories from your after-sales service
or from specialist retailers. You will find a variety of suitable
products for your oven in our brochures and on the Internet.
The availability of optional accessories and the options for
ordering them on the internet vary depending on the country.
You can find information on this in the sales documents.
Not every optional accessory is suitable for every appliance.
When purchasing, please always quote the complete
identification number (E no.) of your appliance.
Optional accessories HEZ number Function
Metal roasting dish HEZ6000 The metal roasting dish is suitable for glass ceramic hobs with
extended cooking zone. Also suitable for induction hobs, pro-
grammes and automatic roasting. The roasting dish is enamel
on the outside with a non-stick coating on the inside.
Pizza tray HEZ317000 Particularly good for pizza, frozen meals and round tarts. You
can use the pizza tray instead of the universal pan. Slide the
tray in above the wire rack and proceed according to the
instructions in the tables.
Insert wire rack HEZ324000 For roasting. Always place the grill wire rack on the universal
pan. This ensures that dripping fat and meat juices are col-
lected.
Grill tray HEZ325000 Used for grilling instead of the grill wire rack or used as a
splatter guard to protect the oven from becoming heavily
soiled. Only use the grill tray with the universal pan.
Grilling on the grill tray: only shelf positions 1, 2 and 3 can be
used.
The grill tray as a splash guard: the universal pan is inserted
together with the grill tray under the wire rack.
Baking stone HEZ327000 The baking stone is perfect for preparing home-made bread,
bread rolls and pizzas which require a crispy base. The baking
stone must always be preheated to the recommended temper-
ature.
Enamel baking tray HEZ331000 For cakes and biscuits.
Slide the baking tray into the oven with the sloping edge facing
towards the oven door.
Enamel baking tray with non-stick coating HEZ331010 The baking tray is ideal for laying out cakes and biscuits. Slide
the baking tray into the oven with the sloping edge facing
towards the oven door.
Universal pan HEZ332000 For moist cakes, pastries, frozen meals and large roasts. Can
also be used under the wire rack to catch fat or meat juices.
Slide the universal pan into the oven with the sloping edge fac-
ing the oven door.
Universal pan with non-stick coating HEZ332010 This universal pan is ideal for moist cakes, pastries, frozen
meals and large roasts. Slide the universal pan into the oven
with the sloping edge facing the oven door.
Profi extra-deep pan with insert wire rack HEZ333000 Particularly suitable for preparing large quantities of food.
Lid for the Profi extra-deep pan HEZ333001 The lid converts the Profi extra-deep pan into the Profi roasting
dish.
Wire rack HEZ334000 For ovenware, cake tins, roasts, grilling and frozen meals.
Glass pan HEZ336000 Deep baking tray made of glass. Can also be used as a serv-
ing dish.
2-level telescopic pull-out rail set HEZ338250 With the pull-out rails at levels 2 and 3, you can pull the acces-
sories out further without them tilting.
3-level telescopic pull-out rail set HEZ338352 With the pull-out rails at levels 1, 2 and 3, you can pull the
accessories out without them tilting.
3-level telescopic pull-out rail set HEZ338356 With the pull-out rails at levels 1, 2 and 3, you can pull the
accessories out without them tilting.
Universal roasting dish HEZ390800 Particularly suitable for preparing large quantities of food. The
roasting dish has a granite enamel exterior and an ovenproof
glass lid. The glass lid may be used as a gratin dish.
Glass roasting dish HEZ915001 The glass roasting dish is suitable for steamed food and souf-
flés. Ideal for programmes and automatic roasting.
10
After-sales service products
You can obtain suitable care and cleaning agents and other
accessories for your domestic appliances from the after-sales
service, specialist retailers or (in some countries) online via the
eShop. Please specify the relevant product number.
Before using the oven for the first time
In this section, you can find out what you must do before using
your oven or gas hob to prepare food for the first time. First
read the section on Safety information.
Setting the time of day
When you connect the power for the first time, the x symbol
lights up.
1.Make sure that the x is flashing in the display.
2.Press the 0 button.
The display goes dark.
You can use the oven clock as a timer. How to set the timer is
explained on the following pages.
Caution!
The clock runs independently of the lower gas burner and gas
grill.
The oven clock can be used as a timer.
The clock runs independently of the oven.
The clock has no effect on the gas supply to the lower gas
burner and grill burner. The gas supply is interrupted if the
switch is turned off.
Heating up the oven
To remove the new cooker smell, heat up the oven when it is
empty and closed. Ensure that no packaging material has been
left in the cooking compartment.
Setting procedure for the lower gas burner
Example in the picture: Heat at 270 °C
1.Open the top cover. The top cover must remain open for as
long as the oven is in operation.
2.Open the main gas supply to the appliance. Connect the plug
in the socket. Open the oven door.
3.Push in the switch for the lower gas burner and turn it to
270 °C.
4.While holding the switch for the oven's lower gas burner
depressed, press the ignition button
8 .
5.The gas escaping from the oven's lower gas burner is ignited
using the ignition button. To activate the safety pilot, press
and hold the lower gas burner on the oven for 10 seconds.
6.Look through the inspection port to make sure that the flame
is lit. If it is not, repeat the process from step 3.
7.Close the oven door slowly.
8.Turn off the switch for the lower gas burner after 30 minutes.
How to set the gas grill
1.Open the top cover. The top cover must remain open for as
long as the oven is in operation.
2.Open the main gas supply to the appliance. Connect the plug
to the socket.
3.Insert the protective plate into the groove under the control
panel.
The protective plate is inserted with the longer edge at the
front with the elbow pointing downwards.
Secure the protective plate in the groove underneath the
control panel using the retainers.
Make sure that the protective plate is engaged in the
retainers. If the protective plate cannot be pulled out, it is
correctly engaged. You can now use the protective plate
safely. Otherwise, insert the protective plate into a groove at a
slightly higher angle and make sure that it engages in the
retainers.
4.Close the oven door so that it touches the protective plate.
5.Press the function selector and turn it clockwise to the (
grill setting.
Cleaning cloths for stainless-steel surfaces Product no. 311134 Reduces the build-up of dirt. Impregnated with a special oil for
perfect maintenance of your appliance's stainless-steel sur-
faces.
Oven and grill cleaning gel Product no. 463582 For cleaning the cooking compartment. The gel is odourless.
Microfibre cloth with honeycomb structure Product no. 460770 Especially suitable for cleaning delicate surfaces, such
as glass, glass ceramic, stainless steel or aluminium. The
microfibre cloth removes liquid and grease deposits in one go.
Door lock Product no. 612594 To prevent children from opening the oven door. The locks on
different types of appliance door are screwed in differently.
See the information sheet supplied with the door lock.
11
6. Keeping the function selector pressed, push the 8 ignition
button.
7. The gas escaping from the gas grill is ignited using the
ignition button. To activate the safety ignition, press and hold
the function selector for 10 seconds.
8. Check that the flame is lit. If it is not, repeat the process from
step 5.
9. After 30 minutes, switch off the function selector. Once the
oven has cooled down, remove the protective plate again.
Cleaning the accessories
Before you use the accessories for the first time, clean them
thoroughly with hot soapy water and a soft dish cloth.
Advance cleaning of burner cup and cap
Clean the burner cap (1) and cup (2) with water and washing-
up liquid. Dry the individual parts carefully.
Place the burner cup and cap back on the burner shell (5).
Ensure that the igniter (3) and flame safety pin (4) are not
damaged.
The nozzle (6) must be dry and clean. Always position the
burner cap exactly over the burner cup.
Making settings on the hob
Your hob is equipped with four gas burners. The following
information explains how to light the gas burners and set the
size of flame.
Igniting the gas burners
Always position the burner cap exactly over the burner cup.
Openings on the burner cup are always unobstructed. All parts
must be dry.
1. Open the top cover. The top cover must remain open for as
long as the oven is in operation.
2. Turn the switch for the desired burner anticlockwise to the
large flame symbol
.
3. Press and hold the burner knob and press the ignition button
at the same time. The gas burner ignites.
4. Press and hold the burner knob for approximately 1-3
seconds. The safety pilot is activated. If the gas flame goes
out, the gas supply is automatically interrupted by the safety
pilot.
5. Set the desired flame size. Between setting û Off and setting
, the flame is not stable. Therefore, always choose a setting
between
large and ˜ small flame.
6. If the flame goes out again, repeat the process from step 2.
7. To end the cooking process: Turn the burner knob û
clockwise to the Off position.
The ignition device should not be actuated for more than 15
seconds. If the burner does not light within 15 seconds, wait for
at least one minute. Then repeat the ignition process.
The gas burner does not ignite
If there is a power cut or if the ignition plugs are damp, you can
light the gas burners with a gas lighter or a match.
Table - Cooking
Select the right saucepan size for each burner. The diameter of
the pot or pan base should be the same as that of the burner.
Cooking times depend on the type, weight and quality of the
food. Deviations are therefore possible. You yourself can best
judge the optimal cooking time.
Minerals and vitamins are very quickly destroyed during
cooking. Therefore, only use a little water. This will help you
retain vitamins and minerals. Select short cooking times so that
the vegetables remain firm and full of nutrients.
Example Dish Burner Heat setting
Melting Chocolate, butter, margarine Economy burner small flame
Heating Stock, tinned vegetables Standard burner small flame
Heating and keeping
warm
Soups Economy burner small flame
Braising* Fish Standard burner between large and small flame
* If you are using a saucepan with a cover, turn the flame down as soon as it reaches boiling point.
** For frying on the wok burner, we recommend that you use a wok.
12
Setting the oven
Here you can find out how to set the oven.
This is how you adjust the lower gas burner in
the oven
When the lower gas burner is lit, you can bake on a baking
sheet with the oven door closed.
Example in the picture: Baking at 170 °C
1.Open the top cover. The top cover must remain open for as
long as the oven is in operation.
2.Open the main gas supply to the appliance. Connect the plug
to the socket. Open the oven door.
3.Push in the switch for the lower gas burner and turn it to
170 °C.
4.While holding the switch for the lower gas burner depressed,
press the ignition button
8 .
5.The gas escaping from the oven's lower gas burner is ignited
using the ignition button. To activate the safety ignition, press
and hold the lower gas burner on the oven for 10 seconds.
The safety ignition is activated. If the gas flame goes out, the
gas supply is automatically interrupted by the safety ignition
system.
6.Look through the inspection port to make sure that the flame
is lit. If it is not, repeat the process from step 3.
7.Close the oven door slowly.
8.Preheat the empty oven for approximately 15 minutes before
baking.
9.When the dish has finished cooking, turn off the switch for the
lower gas burner.
You can change the temperature at any time.
ã=Caution:!
The ignition device should not be actuated for more than 15
seconds. If the burner does not light within 15 seconds, wait for
at least one minute. Then repeat the ignition process.
Setting procedure for the gas grill in the oven
1.Open the top cover. The top cover must remain open for as
long as the oven is in operation.
2.Open the main gas supply to the appliance. Connect the plug
in the socket.
3.Insert the protective plate into the groove under the control
panel.
The protective plate is inserted with the longer edge at the
front and the curvature pointing downwards.
Secure the protective plate in the groove underneath the
control panel using the retainers.
Make sure that the protective plate is engaged in the
retainers. If the protective plate cannot be pulled out, it is
correctly engaged. You can now use the protective plate
safely. Otherwise, insert the protective plate into a groove at a
slightly higher angle and make sure that it engages in the
retainers.
4.Close the oven door so that it touches the protective plate.
5.Press the function selector and turn it clockwise to the (
grill setting.
6.Keeping the function selector pressed, push the 8 ignition
button.
7.The gas escaping from the gas grill is ignited using the
ignition button. To activate the safety pilot, press and hold the
function selector for 10 seconds.
The safety pilot is activated. If the gas flame goes out, the gas
supply is automatically interrupted by the safety pilot.
Braising* Potatoes and miscellaneous
vegetables, meat
Standard burner between large and small flame
Cooking* Rice, vegetables, meat dishes
(with sauces)
Standard burner large flame
Frying** Pancakes, potatoes, schnitzel,
fish fingers
Wok burner between large and small flame
Example Dish Burner Heat setting
* If you are using a saucepan with a cover, turn the flame down as soon as it reaches boiling point.
** For frying on the wok burner, we recommend that you use a wok.
13
8. Check that the flame is lit. If it is not, repeat the process from
step 5.
9. When the dish has finished cooking, switch the function
selector off. Once the oven has cooled down, remove the
protective plate again.
ã=Caution!
The ignition device should not be actuated for more than 15
seconds. If the burner does not light within 15 seconds, wait for
at least one minute. Then repeat the ignition process.
Setting the timer
You can use the timer as a kitchen timer. It runs independently
of the oven. The timer has a special signal. This means that you
can tell whether the timer or cooking time has expired.
Setting procedure
1. Press the 0 Clock button.
The
S timer symbol flashes.
2. Use the + or - button to set the timer time.
+ button / default value = 10 minutes
- button / default value = 5 minutes
The timer starts after a few seconds. The
S symbol appears in
the display. The elapsed time is shown.
The time has elapsed
A signal sounds. Press the
0 Clock button. The timer display
goes out.
Changing the timer duration
Press the Clock button. Use the + or - button to change the
time.
Cancelling the setting
Press the
0 Clock button. Press the - button repeatedly until a
zero appears in the display.
The timer and cooking time count down at the same time
The symbols light up. You can see the timer time counting
down in the display.
To query the
x remaining time:
Press the
0 button.
The queried value appears in the display for a few seconds.
Care and cleaning
With attentive care and cleaning, your hob and oven will retain
its looks and remain in good working order for a long time. We
will explain here how you should care for and clean them
correctly.
Notes
Slight differences in the colours on the front of the oven are
caused by the use of different materials, such as glass,
plastic and metal.
Shadows on the door panel which look like streaks, are
caused by reflections made by the oven light.
Enamel is baked on at very high temperatures. This can
cause some slight colour variations. This is normal and does
not affect operation. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.
Upper glass cover
Before opening the top cover, remove any spills with a cloth.
Use glass cleaner if possible.
For cleaning, remove the top cover. To do this, hold the cover
securely on both sides with both hands and pull it upwards.
If the cover hinges become loose, note the letters marked on
them. The hinge with the letter R must be fitted on the right, and
the hinge with the letter L must be fitted on the left.
After cleaning, re-assemble the top cover following the same
procedure in reverse order.
Only close the top cover once the burners have cooled down.
Cleaning agents
Damage to the various different surfaces caused by using the
wrong cleaning agent can be avoided by observing the
following instructions.
When cleaning the hob do not use
undiluted washing-up liquid or dishwasher detergent,
scouring pads,
abrasive cleaning agents such as oven cleaner or stain
remover,
high-pressure cleaners or steam jets.
Do not clean individual parts in the dishwasher.
When cleaning the oven do not use
sharp or abrasive cleaning agents,
cleaning agent with a high alcohol content,
scouring pads,
high-pressure cleaners or steam jets.
Do not clean individual parts in the dishwasher.
Wash new sponges thoroughly before first use.
14
Detaching and refitting the rails
The rails can be removed for cleaning. The oven must have
cooled down.
Detaching the rails
1.Lift up the front of the rail
2.and unhook it (figure A).
3.Then pull the whole rail forward
4.and remove it (Fig. B).
Clean the rails with cleaning agent and a sponge. For stubborn
deposits of dirt, use a brush.
Refitting the rails
1.First insert the rail into the rear socket, press it to the back
slightly (figure A),
2.and then hook it into the front socket (figure B).
The rails fit both the left and right sides. Ensure that, as shown
in figure B, levels 1 and 2 are below and levels 3, 4 and 5 are
above.
Stainless steel
fronts
Wipe with some washing-up liquid and a damp cloth. Always wipe parallel to the natural grain. Otherwise,
you may scratch the surface. Dry with a soft cloth. Remove flecks of limescale, grease, starch and albumin
(e.g. egg white) immediately. Do not use any abrasive materials, scouring sponges or rough cleaning
cloths. The stainless steel fronts can be polished using a special care product. Follow the manufacturer's
instructions. You can purchase special stainless steel cleaner from our after-sales service or from specialist
retailers.
Enamel surfaces and
lacquered surfaces
Clean with some washing-up liquid and a damp cloth. Dry with a soft cloth.
Burners and steel
grid of the gas burn-
ers
Do not clean in the dishwasher. Remove the wire rack and clean with a sponge, washing-up liquid and
some hot water. Remove the burner cup and cap. Clean with a sponge and some hot water and washing-up
liquid. Ensure that the gas outlets on the burner cups are clean and unobstructed. Brush the igniters with a
small, soft brush. The gas burners only work properly when the igniters are clean. Remove food residue
from the burner shells with some washing-up liquid and a damp cloth. Only use a little water. Water must
not be allowed to enter the appliance. Ensure that the nozzle opening does not become blocked or dam-
aged during cleaning. Dry all parts after cleaning and place the burner cover accurately on the burner cup.
If the parts are not positioned accurately, it will be harder to ignite the burner. The burner covers are coated
with black enamel. Due to the high temperatures, discolouration may occur. This will not impair the function
of the burner. Replace the wire rack in the oven.
Electric hob (option) Clean with the hard side of a scouring sponge and some liquid scouring agent. After cleaning, switch the
hob on briefly to dry it. Wet hobs rust over time. Then apply a care product. Always remove spilt liquids and
food residue immediately.
Metal ring of the
electric hob (option)
The metal ring may discolour with time. However, it is possible restore the original colour. Clean the ring
with the hard side of a scouring sponge and some liquid scouring agent. When doing so, make sure that
you do not scour the adjacent surfaces, as this could damage them.
Knobs Clean with some washing-up liquid and a damp cloth. Dry with a soft cloth.
Door glass Can be cleaned with glass cleaner. Do not use any abrasive cleaning agents or sharp metal objects. These
could scratch and damage the surface of the glass panel.
Seal Wipe with a damp cloth. Dry with a soft cloth.
Oven interior Clean with hot water or vinegar solution. For heavy soiling: Only use oven cleaner on cold surfaces.
Glass cover on the
oven light
Clean with some washing-up liquid and a damp cloth. Dry with a soft cloth.
Accessories Soak in hot soapy water. Clean with a brush or a sponge.
Aluminium baking
tray (option)
Do not clean in the dishwasher. Never use oven cleaner. To avoid scratches, never touch the metal sur-
faces with a knife or similar sharp object. Wipe the surfaces horizontally and without applying pressure with
soapy water and a soft window cloth or a lint-free microfibre cloth. Dry with a soft cloth. Do not use any
abrasive materials, scouring sponges or rough cleaning cloths. They could scratch the baking tray
Childproof lock
(option)
If a childproof lock has been fitted on the oven door, it must be removed before cleaning. Soak all plastic
parts in hot soapy water and wash with a sponge. Dry with a soft cloth. If very dirty, the childproof lock will
not work properly.
Plinth drawer
(option)
Clean with some washing-up liquid and a damp cloth. Dry with a soft cloth.
Accessories Soak in hot soapy water. Clean with a brush or sponge.

%



$
%
$
15
Detaching and attaching the oven door
For cleaning purposes and to remove the door panels, you can
detach the oven door.
The oven door hinges each have a locking lever. When the
locking levers are closed (figure A), the oven door is secured in
place. It cannot be detached. When the locking levers are open
in order to detach the oven door (Fig. B), the hinges are locked.
They cannot snap shut.
ã=Risk of injury!
Whenever the hinges are not locked, they snap shut with great
force. Ensure that the locking levers are always fully closed or,
when detaching the oven door, fully open.
Detaching the door
1. Open the oven door fully.
2. Fold up the two locking levers on the left and right (figure A).
3. Close the oven door as far as the limit stop. With both hands,
grip the door on the left and right-hand sides. Close the door
a little further and pull it out (figure B).
Attaching the door
Reattach the oven door in the reverse sequence to removal.
1. When attaching the oven door, ensure that both hinges are
inserted straight into the opening (figure A).
2. The notch on the hinge must engage on both sides (figure B).
3. Fold back both locking levers (figure C). Close the oven
door.
ã=Risk of injury!
If the oven door falls out accidentally or a hinge snaps shut, do
not reach into the hinge. Call the aftersales service.
Removing and installing the door panels
To facilitate cleaning, you can remove the glass panels from the
oven door.
1. Detach the oven door and lay on a cloth with the handle
facing down.
2. Unscrew the cover on top of the oven door. To do this, undo
the left and right screws (figure A).
3. Lift the panel, and pull it up and out (figure B).
Clean the panels with glass cleaner and a soft cloth.
Do not use sharp or abrasive materials or a glass scraper.
The glass could be damaged.
4. Insert the panel diagonally towards the back. The smooth
surface must face outwards.
5. Put the cover back in place and screw it on.
6. Attach the oven door.
Do not use the oven again until the panels have been
correctly fitted.
%
$
%
$
%
$
&
%
$
16
Troubleshooting
Malfunctions often have simple explanations. Refer to the table
before calling the after-sales service as you may be able to
remedy the fault yourself.
Malfunction table
If a dish doesn't turn out as well as you had hoped, refer to the
section Tested for you in our cooking studio, where you will
find plenty of cooking tips and tricks.
ã=Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be carried
out by one of our trained after-sales engineers.
Replacing the bulb in the oven ceiling light
If the bulb in the oven light fails, it must be replaced. Heat-
resistant, 25 watt spare bulbs can be obtained from our after-
sales service or a specialist retailer. Only use these bulbs.
ã=Risk of electric shock!
Switch off the circuit breaker in the fuse box.
1.Place a tea towel in the cold oven to prevent damage.
2.Unscrew the glass cover by turning it anti-clockwise.
3.Replace the bulb with one of the same type.
4.Screw the glass cover back in.
5.Remove the tea towel and switch on the circuit breaker.
Glass cover
You must replace a damaged glass cover. Suitable glass
covers may be obtained from the after-sales service. Please
specify the E number and FD number of your appliance.
After-sales service
Our after-sales service is there for you if your appliance needs
to be repaired. We will always find the right solution in order to
avoid unnecessary visits from a service technician.
E-number and FD-number
When you call our authorised service, please provide your E-
number and the FD-number. You can find this information on
the label located inside the drawer. You can enter the data for
your equipment here so that you can find it easily in case of a
fault.
Please find the contact data of all countries in the enclosed
customer service list.
To book an engineer visit and product advice
Trust the expertise of the manufacturer, and rest assured that
the repair will be carried out by trained service technicians
using original spare parts for your domestic appliance.
Problem Possible cause Remedy/information
The oven does
not work.
The circuit
breaker is
defective.
Look in the fuse box and
check that the circuit
breaker is in working order.
Power cut Check whether the kitchen
light or other kitchen appli-
ances are working.
The clock dis-
play flashes.
Power cut Reset the clock.
The oven does
not heat up.
There is dust on
the contacts.
Turn the control knobs back
and forth several times.
The gas burner
does not ignite.
Power failure or
damp ignition
plugs.
Light the gas burner with a
gas lighter or a match.
ENo.
FDNo.
Customer Service
O
GB 0844 8928979
Calls from a BT landline will be charged at up to 3
pence per minute. A call set-up fee of up to 6 pence may
apply.
IE 01450 2655
17
Energy and environment tips
Here you can find tips on how to save energy when baking and
roasting in the oven and when cooking on the hob, and how to
dispose of your appliance properly.
Saving energy
Only preheat the oven if this is specified in the recipe or in
the tables in the instruction manual.
Use dark, black lacquered or enamelled baking tins, because
they absorb heat particularly well.
Open the oven door as infrequently as possible while the
food is baking and roasting.
For longer cooking times, the oven can be turned off
10 minutes before the end of the cooking time, and the meal
can be finished using residual heat.
Saving energy with the gas hob
Always use a saucepan which is the correct size for your
food. A larger, less full saucepan requires a lot of energy.
Always place a suitable lid on the saucepan.
The gas flame must always be in contact with the base of the
saucepan.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly manner.
Tested for you in our cooking studio.
Here you will find a selection of dishes and the ideal settings for
them. We will show you which type of heating and which
temperature are best suited for your dish. You can find
information about suitable accessories and the height at which
they should be inserted. There are also tips about cookware
and preparation methods.
Notes
The values in the table apply to dishes placed into the
cooking compartment when it is cold and empty.
Only preheat the appliance if the table specifies that you
should do so. Line the accessories with greaseproof paper
before preheating.
The times specified in the tables are guidelines only. They will
depend on the quality and composition of the food.
Use the accessories supplied. Additional accessories may be
obtained as special accessories from specialist retailers or
from the after-sales service.
Before using the appliance, remove all accessories from the
cooking compartment that you will not be using.
Always use oven gloves when taking hot accessories or
ovenware out of the cooking compartment.
Your oven is suitable for baking on one level.
Caution!
The appliance was manufactured to suit the reference gases
specified in the standards. If a gas is used which does not
comply with the specified gas mixture and pressure, cooking
performance and heat output may not produce the desired
result.
Cakes and pastries
Cake tins
When you are baking in the cake tin, insert the wire rack at the
level indicated and place the cake tin on the wire rack.
Dark-coloured cake tins are the most suitable.
If you use light-coloured baking tins or glass, the baking time
increases and the cake is not browned evenly.
Only use heat-resistant glass dishes. Do not place a hot glass
dish on a cold or wet surface. The glass could break.
If you want to use silicone moulds, follow the guidelines in the
manufacturer's instruction manual. Silicone moulds turn out
slightly smaller than normal cake tins. For this reason, the
quantities may be slightly different to those indicated in your
recipe.
Baking tables for the lower burner in the gas oven
In the tables, you will find the optimum types of heating for a
selection of cakes and gateaux. The temperature and cooking
times depend on the quantity and consistency of the dough.
The values in the table apply to dishes placed into the cooking
compartment when it is cold and empty.
The heat is distributed in the oven as soon as the gas escaping
from the lower gas burner is ignited. For this reason, the
underside of food is usually more browned than the top.
This appliance complies with European Directive
2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE). The directive gives a framework for
the collection and recycling of old appliances, which is
valid across the EU.
Name of the gas Gas mixture (%)
G20 CH
4
= 100
G25 CH
4
= 86, N
2
= 14
G30 n-C
4
H
10
= 50, i-C
4
H
10
= 50
Cake in a mould Accessories Level Temperature in
°C
(lower gas
burner on the
oven)
Cooking time
in minutes
Cakes Round springform cake tin with tube
sheet, deep
2 180 60-80
Cakes Round springform cake tin with tube
sheet, wide
3 180 60-80
Sponge cake Springform cake tin (dia. 26 cm) 2 180 50-60
18
Baking tips
Meat, poultry, fish, toast
Table - cooking - gas grill
The values in the table apply to dishes placed in a cold oven.
Turn the pieces of meat after
Z of the cooking time.
Always place items in the centre of the wire rack.
If you are grilling directly on the wire rack, you should insert the
baking tray at level 1. The fish juices are collected in the pan
and the oven is kept cleaner.
Apple pie Springform cake tin, light (dia. 20 cm) 2 230 60-80
Semolina cake Glass ovenproof dish, rectangular 3 180 60-80
Several small baked items on the bak-
ing sheet
Accessories Level Temperature in °C
(lower gas burner on
the oven)
Cooking time in min-
utes
Small cakes Baking sheet 4 170 70-90
Biscuits Baking sheet 3 180 40-60
Sesame seed rings Baking sheet 4 190 60-80
Puff pastry strudel Baking sheet 4 180 50-70
Yufka dough strudel Baking sheet 3 190 60-80
Yeast-risen pastry Baking sheet 4 170 70-90
Pizza Baking sheet 3 190 50-70
Dish Accessories and oven-
ware
Level Temperature in °C Cooking time in min-
utes
Pasta bake Glass ovenproof dish, rec-
tangular*
2 190 60-80
Potato gratin made using raw ingredi-
ents,
Max. 4 cm deep
Glass ovenproof dish, rec-
tangular*
2 180 60-80
Vegetable goulash Earthenware pot 2 220 80-100
* Only use heat-resistant glass dishes. Do not place a hot glass dish on a cold or wet surface. The glass could break.
Cake in a mould Accessories Level Temperature in
°C
(lower gas
burner on the
oven)
Cooking time
in minutes
You wish to bake according to your own
recipe.
Use similar items in the baking tables as a guide.
How to tell whether sponge cake is
baked through:
Approx. 10 minutes before the end of the baking time stated in the recipe, insert a cock-
tail stick into the cake at its deepest point. If the cocktail stick comes out clean, the cake
is ready.
The cake collapses. Next time, add less liquid. Observe the specified mixing times in the recipe.
The cake has risen in the middle but is
lower around the edge.
Do not grease the edge of the springform cake tin. After baking, loosen the cake care-
fully with a knife.
The cake is too dry. Make tiny holes in the finished cake using a cocktail stick. Then drizzle fruit juice or an
alcoholic drink over it. Next time, reduce the baking time.
The bottom of a fruit cake is too light. Place the cake one level lower the next time.
The fruit juice overflows. Next time, use the deeper universal pan (if available).
The pieces of dough are sticking
together when the yeast rolls are baked.
There must be a distance of about 2 cm between the bread rolls. This gives enough
space for the bread rolls to expand and bake evenly on all sides.
Condensation forms when you bake
moist cakes.
Steam can form during baking, which escapes via the door. The steam may settle and
form water droplets on the control panel or on the fronts of adjacent units. This is a natu-
ral process.
Dish Weight Accessories and oven-
ware
Level Type of heat-
ing
Cooking time in min-
utes
Meat
Steaks, (2 pieces, 3 cm thick) 0.5 kg Wire rack 4
(
30-40
Hamburgers (6 slices) 0.3 kg Wire rack 4
(
10-20
19
Tips for roasting and grilling
Acrylamide in foodstuffs
Acrylamide is mainly produced in grain and potato products
heated at high temperatures, such as potato crisps, chips,
toast, rolls, bread, baked goods made from shortcrust pastry
(biscuits, gingerbread, cookies).
Sausages (5 pieces) 0.2 kg Wire rack 4
(
10-20
Poultry
Chicken drumsticks (4 pieces) 1.5 kg Wire rack 4
(
40-50
Fish
Fish, whole (2 pieces) 1.0 kg Wire rack 4
(
35-45
Fish fillets (4 pieces) 0.5 kg Wire rack 4
(
35-45
Toast
Toasts, browned (4 slices) - Wire rack 4
(
2-4
Toasts with filling, browned from
above (4 slices)
-Wire rack 4
(
3-5
Dish Weight Accessories and oven-
ware
Level Type of heat-
ing
Cooking time in min-
utes
The table does not contain information
for the weight of the joint.
Select the next lowest weight from the instructions and extend the time.
How to tell when the roast is ready. Use a meat thermometer (available from specialist shops) or carry out a “spoon test”.
Press down on the roast with a spoon. If it feels firm, it is ready. If the spoon can be
pressed in, it needs to be cooked for a little longer.
The roast is too dark and the crackling
is partly burnt.
Check the shelf height and temperature.
The roast looks good but the juices are
burnt.
Next time, use a smaller roasting dish or add more liquid.
The roast looks good but the juices are
too clear and watery.
Next time, use a larger roasting dish and use less liquid.
Steam rises from the roast when basted. This is normal and due to the laws of physics. The majority of the steam escapes through
the steam outlet. It may settle and form condensation on the cooler switch panel or on
the fronts of adjacent units.
Recommendations for baking, roasting and grilling with low acrylamide values
General
Keep cooking times to a minimum.
Cook the food until it is golden brown. "Browned, not charred".
The larger and thicker the food, the less acrylamide it contains.
Oven chips Where possible, spread out a single layer of oven chips evenly on the baking tray. To
prevent the chips from trying out quickly, cook at least 400 g on the baking tray.
01
161291
*9000739092*
9000739092
Robert Bosch Hausgeräte GmbH
Carl-Wery-Straße 34
81739 München
Germany
www.bosch-home.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Bosch HGG24W256R/35 User manual

Category
Kitchen & houseware accessories
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI