Welcome
Thank you for purchasing the new Hair Clipper SY-HCT1X. In order to benefit fully from this product please read
the following instructions carefully. Store the instructions manual in a safe place for future reference.
Important safeguards
• Before the first use of the appliance check that the voltage indicated on the rating label corresponds to the
mains voltage in your home.
• For home use only. Do not use for industrial purposes. Do not use the appliance for any other purposes
than described in this instruction manual.
• Do not use outdoors.
• Always unplug the appliance from the power supply before cleaning and when not in use.
• To prevent risk of electric shock and fire, do not immerse the appliance in water or any other liquids.
However if this does occur DO NOT TOUCH the appliance, unplug it immediately and contact your near
service center.
• Do not take this product to a bathroom or use near water.
• Do not immerse the recharging stand or adaptor in water.
• Never charge the unit near water.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliances by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not leave the appliance switched on when not in use.
• Do not use other attachments than those supplied.
• Do not operate after any malfunction, cord damage, battery leak, charging stand damage or adaptor
damage.
• Do not attempt to repair, adjust or replace any parts of the appliance. Check and repair any damages by
contacting Sytech Service Center.
• Keep the cord away from sharp edges and hot surfaces.
• Do not place or store the appliance where it can fall or be pulled into a tub or sink.
• Do not pull, twist, or wrap the power cord around the appliance.
• Never insert any objects into the openings of the appliance.
• Before use, make sure that blades are adjusted properly.
• Do not place the appliance while it is operating on any surface, it may cause injury or damage.
• Do not use the appliance with a damaged comb, or with teeth missing from the blades as injury may occur.
NOTE: KEEP THE BLADES OILED
• Do not use the appliance when the skin is infected.
• Do not use the appliance on animals.
• The manufacturer reserves the right to introduce minor changes into the product design without prior
notice, unless such changes influence significantly the product safety, performance, and functions.
When charging:
• Please don’t charge the unit if temperature is lower than 0°C or higher than 40°C.
• Please don’t charge near direct sunlight, or any other heat source
• The standard charging time is 1.5 hours. In order to avoid damaging the batteries, do not overcharge.
Once the unit is completely charged, remove the adaptor from the base or from the clipper.
Caution:
- Clean the housing using only a cloth slightly dampened with water or a mild soap solution.
- Never use a caustic solution.
- Never submerge the clipper in water.
- Keep away from the children.
- This clipper may become warm during operating and/or charging, this is normal.
- When using, do not pull or hold on the cord, this may cause damage to the user.
- Never touch the moving parts as this may result in severe injuries.
Parts identification:
1. Blade
2. Length adjustment
3. Switch
4. LED digital display
5. Charging stand
6. Comb attachment
7. Adaptor
8. Brush
9. Oil
How to use
The SY-HCT1X can be used cordlessly and while it is being charged.
Connect the adaptor to one end of the clipper and the other end to the wall outlet to charge the unit without the
base. The unit can also be charged using the charging stand. Connect one end of the adaptor to the charging
base and the other end to the wall outlet. Then place the unit on the charging base and the unit will charge. For a
complete charge it takes about 1.5 hours. When the unit is fully charged, it can be used continuously for more
than 45 minutes. The clipper has a LED digital display indicating the user the battery level while using and the
charge level while charging.
Before Starting the Haircut
• Select the comb attachment and the level of haircut desired (please see following sections on how to select
haircut level). Place the clipper besides the hair and push the switch button to ON to start using the hair
clipper. Carefully move in the same directions throughout the haircut.
• Check the clipper, making sure that there is no oil between the cutting blade teeth. Turn the unit on to
distribute the oil and to make sure it is running smoothly before using. Wipe off any excess oil. This should
be done before each use.
• In the case of cutting someone else’s hair, seat the person so the head is approximately at the eye level.
This allows ease of visibility while cutting and a better control of the clipper.
• Place a towel around the neck and shoulders of the person getting the haircut.
• Before cutting always comb the hair so it is tangle free.
Reminders
• Cut the hair in an even and slow manner. Use short strokes only and work gradually over the entire head.
• Always take off a little hair at a time; you can always trim off additional hair later.
• As you work, comb the hair frequently back into the style to which you are cutting.
• When cutting with this hair clipper it is better to leave the hair dry, not wet. With dry hair, it is much easier to
control the amount of the hair being cut.
• Cutting hair requires practice so it is always better to leave the hair longer for the first few haircuts until you
become used to the hair clipper levels and how much hair does each level cut.
How to use the comb attachment
First choose a desired comb attachment and then slide the comb attachment down over the main blade as
shown in the picture below. You may then adjust the hair cutting level by turning the dial clockwise or
anticlockwise.
To remove the comb attachment, gently push the comb upwards and slide it out as shown in the picture below
as well.
How to use and care the blade
1. Hold the handle of the hair clipper and push the upper part outwards and away from the blade. (Please
see picture)
2. Using the brush, clean the blade in order to remove excess hair which may be caught between the
blades. Lubricate the space between the fixed blade and the moving blade with 2 or 3 drops of oil after
every few uses.
3. To place the blade back on the clipper, first set the dial to 2.0mm, then place the blade back in the
correct position and then push it in until it clicks firmly in position (please see picture).
After using
Clean the unit after every use and keep the switch turned off to maintain optimal performance.
Specifications
• Professional Electrical Hair Clipper
• Fixed blade with Titanium coating
• Moving Ceramic blade
• Rechargeable
• Direct Drive use function
• Charging time: 1.5 hours
• Working time: 45 mins
• Level Adjustment for perfect cut
• Powerful and silent motor
• 4 Attachment combs of 3,6,9,12 mm
• Hair-cut depth regulator: 0.8 – 2mm
• Power source: 100-240V/50Hz, 3V 1000mA
• Battery: 2xAA. 1200 mAh (NI-MH)
• Power: 9W
• Accessories supplied:
• Oil bottle
• Cleaning Brush
• AC Adaptor
DECLARATION OF CONFORMITY
Manufacturer Name: Satyatrade S. L.
Address: Pol.Ind.La Raya. C/ Guadalquivir, 2.
Camarma de Esteruelas, 28816 Madrid
Tel: 902 430 967
Fax: 91 8864285
NIF: B83254763
Manufacturing country: China
Description: Hair Clipper
Sytech® SY-HCT1X complies with the following directives:
CE Standard: Directive 2004/108/CE
LVD Standard: 2006/95/EC
ROHS Standard: 2011/65/EU Restriction of Hazardous Substances
Signed: Ajeet Nebhwani Utamchandani
Sole Administrator
/